Search Documents

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By D van der Wal, R Dobbe, K Moeller

"Ore mineralogy and texture are primary variables controlling mill recovery efficiency in flotation plants. However, tracking daily variations of key mineralogical characteristics such as species-by-species liberation is not possible with current on stream analysers and assay lab techniques. In addition, traditional plant mineralogical analysis limited by long data turn-around times from central analysis laboratories typically provides only a time-averaged view of mill performance, e.g. by means of monthly composite feed, con or tailings analysis.This paper presents the results of a development and first field test of an on-site Automated Mineralogy solution (MLA or QEMSCAN) with the specific goal of monitoring recovery variation, ore quality and flotation performance on a mineral species-by-species and day-by-day basis, from up to twelve million direct particle observations per month. The trial was performed at a Pb/Zn-Ag operation in the US from November 2012 to April 2013. The focus of the study was three-fold: to validate the robustness of equipment and operational procedures for daily use by mine site technicians at a remote mine site to develop a methodology to boil down hundred-thousands of Automated Mineralogy particle data from size-by-size con and tailings samples to a couple of numbers meaningful to chief metallurgists to monitor recovery trend changes and correlate these to changes in the feed properties and/or flotation efficiency.The study focused primarily on the Pb/Ag rougher-concentrator circuit. Ten polished blocks of two and three size fractions of con and tailings were prepared by mine site technicians during a daily twelve hour shift. Eight hours of daily measurement time by the instrument revealed an estimate of the dayÆs recovery performance, ore quality and flotation performance for Freibergite (Ag-species) and Galena (Pb-species), within 36 hours from initial sampling. Data quality was assessed by means of calculated versus measured assay reconciliation. Cumulative sum curves of recovery performance, ore quality and flotation performance reveal trend changes with a frequency of 1 to 4 weeks. These were correlated to cumulative sum curves of e.g. locked and slimed particle classes of the mineral species of interest, attempting to identify a possible root cause of recovery performance trend changes. Systematic over-grinding and flotation chemistry issues were the primary causes of below average plant operations during the trial.CITATION:van der Wal, D, Dobbe, R and Moeller, K, 2013. Development of an on-site mineralogy solution for metallurgists, in Proceedings MetPlant 2013, pp 126-132 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

By Gregory Poole

With access to the World Wide Web, many resources are readily available for improving claim reports. With a little time spent on line, a more thorough report can be created. Claimants will accept the conclusions of a report more readily when they can view support information on their own computer, particularly when the support information is not just from blasting related web sites. Some suggested resources are discussed including aerial pictures, local tax maps, topographical maps and home repair web sites. This paper provides suggestions for tracking down support information on the web and information on how to properly reference this information. Case studies of several claim investigations are presented. These are some examples of how a little time spent online provided clear and convincing evidence to support the conclusions of the investigation.

Jan 1, 2006

By G. G. Barbante

An understanding of the thermodynamics of smelting copper anode slimes is a prerequisite for improvements to the process. During slimes smelting, a silver-copper selenide matte is formed and subsequently oxidised to silver metal. As part of a series of investigations, molten silver selenide matte was oxidised at 1 100 degrees C with pure oxygen. The chemical potential diagram for the system was developed and used for qualitative prediction of the results of the experiments. A simple, computational thermodynamic model of converting is presented, the adjustable parameters of which were determined by matching the model with the experimental results. The practical usefulness of the model was demonstrated by predicting the effect on silver recovery of smelting temperature and of using either oxygen or air as the smelting gas

Jun 21, 1905

The minerals industry focus over much of the past twenty years has been on cost reduction and production growth supported, but not driven, by technology improvements. Mergers and acquisitions, and the demands of financial markets, have been high priority items whereas research and development and technology based innovation have received less attention and have been cut back in many companies. Technology improvements will be critical if the industry is to make progress on the stated aims of improving energy efficiency, reducing water usage and maximising recovery from deposits. They will also be important for improving capital efficiency and in treating difficult deposits. However the role technology based innovation will play both in the overall industry, and within individual companies, during the next decade is quite uncertain. There are major challenges in progressing technology based innovation in an industry with limited technical resources which is dominated by long life high capital operations. Specific opportunities for energy and productivity improvements exist but face significant technical and structural barriers that need to be overcome if the industry is to significantly improve performance. Current evidence suggests that changes in approach will be needed for these improvements to be realised. Recent studies in the United States and Canada have highlighted the wide range of energy performance across the industry and the scope for marked improvement from both incremental improvements and increased research and development. Comminution, material transportation and underground mine ventilation were identified as high priority areas. Opportunities within these areas are discussed both in respect of specific technologies and in how they may change performance. The role of open innovation as a source of new technology is also discussed. This is an abstract only. No full paper was prepared for this presentation.

Sep 13, 2010

By R. S. Dean

"INTRODUCTION The idea of direct steel is by no means new. Although the work of Bessemer and Siemens provided simple and effective moans for converting pig iron into steel and established the ""blast-furnace route"" as the almost universal method of producing steel, metallurgists have not ceased to dream of direct steel. By direct steel is meant any process by which iron oxide in ore is reduced to Iron of the same or greater purity than the final steel or wrought iron. That is, carbon or alloying elements would be added as needed, not reduced in unwanted quantities into the iron and then removed more or completely by refining (Bessemer or open hearth) only to be readded in desired quantities.In general, direct-steel processes are ""sponge-iron"" processes, because reducing iron oxide without simultaneously alloying the iron with carbon, phcophorus, sulfur, and silicon present in ore and fuel succeeds only if the temperature is below the melting point of the iron. Such solid iron formed by reduction of iron oxide at relatively low temperature is sponge iron, which is butlery and porous. When the reduction proceeds at the higher temperature at which the particles of metal can weld together or finally even melt to yield pellets or balls that do not have the porosity and low-density characteristic of sponge iron, the product might preferably be called simply ""direct iron."""

Jan 1, 1945

By N. Kyriazi

The U.S. Bureau of Mines subjected the CSE SR-lOO self-contained self-rescuer (SCSR) approved by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. The apparatus were heated to 710 C for 48 h, cooled to -450 C for 16 h, vibrated for 9 h, and dropped 1 m on each axis. A critical concern was internal damage to an apparatus, without any obvious external signs, that would cause it to malfunction or seriously degrade its performance. Carbon dioxide (C02) levels in apparatus with combined treatments were higher than in apparatus with individual treatments and untreated apparatus. The higher levels remained within safe limits, however. None of the treatments caused venting of the small oxygen cylinder that provides starter oxygen. Some bottles were found to be empty because of manufacturing defects in the burst disks. This problem was corrected in later models. The heat treatments did make the case ends more difficult to remove and the breathing bag sticky and subsequently more difficult to unfold. An apparatus that was dropped and vibrated had a broken desiccant bag that released some of its contents which compromised the seal of the relief valve. The case was dented from the drops. As with the first-generation self-rescuers, if there is visible damage to the case of the apparatus, the apparatus should be considered to be internally damaged and must be removed from service.

Jan 1, 1990

By None None

Life as a mining/mineral professional doesn’t leave much time for perusing 20-page technical papers. Yet, being technologically savvy is part and parcel of a successful career in this industry. What’s an intelligent, well-informed person to do?

By Vern Pfannenstiel

Jan 1, 2005

By J. E. Nesset

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

By Vincent A. Scovazzo

Benchmarking is a business management process that seeks improvement through the study and reapplication of practices conducted by industry leaders. This discussion presents objectives and organization of benchmarking applied to mining geomechanics. Similar procedures have been successfully applied to mining companies, laboratories, and research organizations involved in mining geomechanics throughout the world. Benchmarking is a structured process that allows an organization to learn from the "best" in the field. The objectives of benchmarking vary depending on the company's targeted areas for improvements. Typical goals include ground control cost reduction, enhanced safety, optimization of geotechnical staffing, development of state-of-the-art design procedures, or the adoption of the "best in the field" geotechnical data management. Once the objective of the study is established and the practices and procedures to be benchmarked are identified, a benchmarking team is formed from internal and outside specialists. Benchmarking in geomechanics is fundamentally different than in most other fields because of the effects of local geologic conditions and regulations, both of which must be understood by all on the benchmarking team, before a comparative analysis can be made.

Jan 1, 2000

By F. M. C. C. Vieira

The DEEPMINE Research Programme sought to develop the technology and competence to mine gold safely and profitably at depths of 3 to 5 km. Among the many issues addressed was the stability and support of rockpasses at ultra-depth. It was found that high virgin and mining-induced stresses could cause the walls of rockpasses to spall, leading to the deterioration and failure. A comprehensive programme of numerical modelling was conducted to investigate alternative mining layouts and sequences to ameliorate the problem.

Jan 1, 2005

By H. Kotzé

Titania slag is used as feedstock in the production of titanium dioxide pigment. It (titania slag) is the product of ilmenite smelting,a process whereby ilmenite is reduced at high temperature utilizing anthracite as a reducing agent. Although various slag tapping configurations are employed throughout the ilmenite smelting industry, the method of tapping the slag from the furnace into bell shaped cast steel pots, was the subject of investigation in this study. The paper describes the formulation of a cooling model used to calculate and subsequently predict the temperature profile of a slagblock during its cooling within the various cooling environments of pot cooling, air cooling and water cooling. The model was calibrated against actual internal slag temperature measurements and verified with information obtained from both pilot and industrial scale blocks. The paper concludes with solidification results and their practical implication.

Jan 1, 2010

By Frank E. Williams

This Bureau of Mines report describes 147 known fluorspar deposits in New Mexico and briefly mentions 54 miscellaneous occurrences for which little or no information was obtained. Most miscellaneous occurrences are minor and too poorly exposed to be considered more than prospects. History and production of fluorspar in New Mexico, type of deposition, mineralogy, uses, and grade specifications are discussed. Total mine production of fluorspar in New Mexico is nearly 641,000 tons of various grades of crude ore and hand-sorted material. Fluorspar deposits occur in 13 of the state's 32 counties. Grant, Valencia, and Luna Counties account for 86.4 percent of the total production. During the investigation, 141 deposits were visited. A total of 72 character samples was collected for assay, and 3 larger samples were collected for bench-scale metallurgical tests. Results of these metallurgical tests indicate that an acid-grade product can be obtained with 95 percent recovery of the CaF2 content of the crude ore.

Jan 1, 1966

By Ry Stone

To maintain longwall continuity, NRE Wongawilli Colliery extracted the approximately 20-year-old Thompson Mains and in doing so, 20 roadways were holed into during longwall retreat. The orientation of these roadways with regard to the longwall face varied between (i) a parallel alignment where the entire roadway was simultaneously subjected to a significant increase in vertical stress on holing and (ii) a more favorable high angle of alignment, meaning that only a portion of the roadway was subjected to an increase in vertical stress on holing. In addition, the longwall holed into and was recovered in one of the existing roadways. The geotechnical environment presented several additional challenges during longwall retreat. The orientation of the stress field resulted in a major horizontal stress notch on the maingate and an elevation in the major horizontal stress in front of the longwall face during the retreat up to an adjacent goaf edge. The presence of geological structure zones also resulted in both swings in the major horizontal stress direction and increased levels of roof deformation. The gate road support designs were based on commonly accepted strata management techniques and principles. The support designs in the hole-through roadways were based on empirical design models generated from (i) aconceptual geomechanical model of pre-driven hole-throughand recovery roads and (ii) a worldwide database on pre-driven hole-throughand recovery roads. Imperative to the success of extracting the panel was a sitespecific strata management process. In this regard, consideration was given to the following: roof displacement monitoring in the gate roads (in particular, Longwall (LW) Acceleration Position), roof-to-floor convergence monitoring in the hole-through roadways, the ability of the mine to limit downtime prior to and during holing by utilizing an Authority to Mine (ATM) type process, and the use of Trigger Action Response Plans (TARP).

Jan 1, 2012

By E. J. Sun

The ADS system was developed to reduce accidents related to haul trucks operating under low visibility conditions in surface mining and construction sites, which is based on the GPS, mesh-wireless networks, and the Google-Earth 3D graphic engine as the graphic interface and mine-mapping server. This system has the capability to pin-point and track vehicles in real time using a 3D interface, which is based on user-based AutoCAD mine maps using the Google-Earth graphics interface. All equipped vehicles are shown in a 3D mine map stored in a local server through a wireless network. When low visibility conditions are present, the system indicates available exit/escape routes for driver safety. The research results indicate that the ADS system potentially increases reliability and reduces uncertainty in open pit mining operations by customizing the local 3D digital mining map, constructing the truck 3D models, tracking vehicles in real time using a 3D interface and indicating available escape routes for driver safety.

Oct 1, 2009

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.