Search Documents

By R. J. Hundermark, S. Sun

The oxidation state dependence of the electrical conductivity of a calcium ferrite slag with 25 wt% CaO was measured at 1300°C using a shallow slag layer and two-electrode technique. The experiments were started in air and the slag was sequentially reduced by means of a controlled gas atmosphere using CO2and CO. The electrical conductivity in air was approximately 300 S/m and increased with reduction to approximately 1900 S/m at a pO2of 10-10atm. The interest in the oxidation state dependence of the conductivity of calcium ferrite slags was to provide a comparison with the conductivity of iron silicate slags and to establish the effect of slag basicity on the electrical conductivity and its oxidation state dependence. The results obtained are discussed in terms of the slag structural information available in the literature. The co-ordination of the ferric ions appears to play a large role in determining the electrical conductivity. Keywords: calcium ferrite, slags, electrical conductivity.

Jan 1, 2004

By Q. G. Reynolds

Keywords: Pyrometallurgy, furnace, DC, reverse polarity, dual-electrode The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode, and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions ? this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magneto-hydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By E. T. Turkdogan, P. Grieveson, J. F. Beisler

Jan 1, 1963

By R. M. Cox

The ground forces generated by a properly installed and tensioned mine roof truss assembly can provide permanent mine roof support, even in severe ground conditions, either by direct suspension of the rock loads within the potential failure zone above the mine opening or indirect reinforcement of the natural rock arch that tends to form within the immediate mine roof. Notable advancements in mine roof truss support systems hardware and design technology have occurred since the introduction of the in situ mine roof truss concept for permanent mine roof support in 1966. The systematic installation of mine roof truss support systems has proven to be a very effective method of mine roof control room and pillar mines under a wide variety of ground conditions, even in areas otherwise considered unmineable because of severe roof control problems. Properly designed mine roof truss systems have also been used for permanent support of mine slopes and haulage tunnels.

Jan 1, 2002

By M J. Kindley

The Golden Cross Gold Mine Project is now fully operational and into its second year of operation. Because of its location in the sensitive Coromandel Peninsula , strict water management and environmental requirements had to be met. This led to the development of new technologies for cyanide recovery and the adoption of advanced water management and water treatment systems. This paper discusses the water management and treatment system adopted for contaminated water at Golden Cross and provides data on the operational history to date.

Jan 1, 1993

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966

By Stanley A. Schwartz

In the Piedmont, heavily loaded structures are generally supported by either drilled piers or one of several pile types. The choice of drilled piers or piles is typically one of comparative costs. The cost of a drilled pier foundation is usually the more difficult to predict because of the greater impact that variable conditions and construction monitoring have on cost. Poor specifications, related to the drilling equipment, procedures and bearing level, can also result in large cost extras. In the southern Piedmont, straight shafts are typically extended down to hard rock to achieve primary support in end-bearing: when bells are required, they are often constructed manually. In some eastern and northern Piedmont locations the thickness of the decompossed rock zone is significant and considerable skin friction can be mobilized. Typically piers are constructed in holes temporarily cased with steel liners. The bottom is cleaned of loose material and water, and then evaluated by a geotechnical engineer to confirm the design bearing pressure (and friction, where appropriate) or recommend alternative construction measures.

Jan 1, 1988

The paper considers Aboriginal responses to large-scale mining, including Indigenous attitudes towards land access for exploration and project development. The core question, in which I have been interested for some time (Trigger 1997a; 2000; 2001), is: what are the significant factors affecting responses among Indigenous communities to mining exploration and development project proposals?

Jan 1, 2002

By Kenneth Eilerts

[The development and operation of ?combination on wells?5/ have created new and unusual problems, many of which cast to solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to Know whether liquid will be formed in the reservoir it as a result o a isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how gyres sure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios of gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and pressure of the oysters are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the fluids under reservoir conditions are particularly important at this time. To rest the immediate requirements of the industry for such experimental information an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date, have boon accumulated, it may be possible to mare dependable estimates of the phase relations ft. high gas-liquid ratio fluids at the pre runes and temperatures characteristics of ?combination-well? reservoirs.]

Jan 1, 1940

By Norman O. Lotter, Simon Yu, Tony Deng, Antonio Di Feo

"Xstrata Nickel’s Raglan operation, northern Québec, achieved paymetal recovery gains in 2007 by switching the collector from potassium amyl xanthate to sodium isobutyl xanthate. To follow on from that position, Xstrata Process Support (XPS) and A. Di Feo of Raglan proposed that a mixed xanthate system be formulated and tested towards further performance gains. This work selected ethyl and isobutyl xanthates as the candidates. An optimized ratio of these was to be determined by a designed experiment. This suggestion was based on an abundance of published literature that reported mixed collector systems outperformed single ones. A partial factorial design was used to configure four test conditions and a mid-square for the flotation work. The testwork was conducted using High Confidence Flotation Testing. The raw data were analyzed and modelled by Design-Expert software. An optimum ratio of 1.6:1.0 by mass (1.32:1.0 in molar terms) of isobutyl:ethyl xanthate was determined. Without this modelling, the optimum ratio would have been missed. Results obtained with the new baseline flotation test using this optimized mixture showed a 3.3% Ni recovery gain in the bypass concentrate and more than 1% recovery gain for PGM over the single PIBX system. This system has been proposed for and accepted as a plant scale trial in the first half of 2010.INTRODUCTIONConcentrator OperationsMilling and flotation of sulphide ores ahead of smelting and refining is a common practice. This choice results in the larger and more variable paymetal loss in the production of saleable metal [Cramer, 2001]. For this reason, it is common to see an ongoing performance improvement programme at the operations level. When successfully performed, these e"

Jan 1, 2010

By David Bendersky

This report covers a technical and economic investigation of old electrical power systems, equipment and practices being used in the metal/non-metal raining industry. The principal sources of information were the MSHA District offices, visits to representa¬tive mines and mills, equipment manufacturers and the literature. A list of 85 mines and mills, submitted by the MSHA Districts as candidates for this study, is given and their characteristics are analysed. The electrical power systems and practices at the 10 mines and 9 mills which were visited are described. The principal areas which do not conform to standard electrical practices are discussed with emphasis on the safety aspects of these practices. The costs to update electrical power systems and practices in metal/non-metal mines and mills are given. The principal findings of the study are summarized and recommendations are submitted.

Jan 1, 1980

By Y. Oka, H. Majima

When a rock particle is subjected to an external force, internal stresses and deformations are experienced by the particle. Assuming that the breakage of a rock is mainly due to tensile stresses generated by the action of a pair of concentrated loads, F, directed in compression towards the loading points at the shortest distance, as illustrated in Fig. 1, the stress and deformation experienced by a particle of irregular shape can be determined with the aid of the theory of elasticity. According to the photoelastic experiments made by one of the present authors,' the stress states in a rock particle of irregular shape are quite similar to that of an inscribed sphere of diameter x, as indicated in Fig. 1, but accompanied by the faint stresses, in the vicinity of the particle outside of the inscribed sphere. Therefore, the stress components in an irregularly shaped particle can be estimated by referring to stress components in a sphere. Applying polar spherical coordinates to an elastic spherical body, as shown in Fig. 1, the stress components are all expressed as multiples of F /x2 and more or less influenced by the loading angle and Poisson's number m. In general, the energy w, acting on a rock particle is defined as the product of loading compression F

Jan 1, 1970

By E. Chin

The only economically significant mineral exploited in Banglades - during 1981 was natural gas. Nitrogenous fertilizer production was important to the agricultural sector and was totally dependent on the natural gas for fuel and raw material. Domestic cement plants were also fu pled by natural gas. The flat river-delta terrain for most of Bangladesh makes the potential for discovering major mineral deposits poor. No large deposits of metal ores have been found and only in the small hilly southeastern section of the country is there even much chance of finding any. Heavy mineral sand deposits may eventually be exploited along the Chittagong coastline. There is a good potential for crude oil discoveries. The Bangladesh economy has been heavi¬ly subsidized by billions of dollars of foreign aid since the country's inception. A World Bank report recommended total aid needs of over $2.6 billion in fiscal year (FY) 1980-81. It received commitments for barely over one-half that amount.

Jan 1, 1983

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By Napisporn Memongkol

Syntheses of Al-TiC-Al2O3 and Al-SiC-Al2O3 composites were obtained in situ by carbothermal reduction of mixtures of Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders. The reductions were carried out in a horizontal tube furnace under flow of inert gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of aluminum reinforce with titanium carbide and alumina and aluminum reinforce with silicon carbide and alumina. The effect of the reaction temperature (1000 o C ? 1200 o C) and condition of precursors on the Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders were investigated using XRD and SEM method. The synthesized products showed those composites with aluminum matrix and titanium carbide and alumina as reinforced phases and aluminum matrix and silicon carbide and alumina as a reinforced phase was formed.

Jan 1, 2006

By R. M. Lamya

The kinetics of copper cementation during atmosphere leaching of a Ni-Cu matte in CuSO4-H2SO4 solution was studied as a function of initial copper ion concentration, initial acid concentration, temperature, stirring rate, particle size distribution and pulp density. It was found that all these process variables influenced the rate of cementation. A two-stage rate of reaction was observed inmost of the experiments, with the rate of cementation in the initial stage being slower than that of the subsequent second stage. The increased rate of cementation in the second stage was attributed to the enhancing effect of the surface deposit. The cementation process was found to take place by two different rate-controlling mechanisms. At a temperature range of 50?70°C, an activation energy of 74.6 kJ/mol was obtained, indicating a surface reaction controlled process. At higher temperatures (70?80°C) a lower value of activation energy was observed (18.2 kJ/mol), indicative of a process controlled by diffusion through surface layers. The structural characteristics of the cemented deposit could not be determined in the investigated system where the deposit was mixed with the leach solid residue.

Jan 1, 2005

By M. Tangstad, B. Monsen, H. Midtgaard

The increased attention towards reducing emissions of fossil CO2 due to its potential global warming effect has resulted in a focus on renewable resources, as charcoal. Since charcoal is produced from growing wood it does not contribute to global warming. This paper gives a brief review of consequences of and reasons for using charcoal in the silicomanganese (SiMn) production. Results are presented from practical SiMn smelting experiments, on a pilot scale, using charcoal as reduction material and comparing with coke. As slag- and CO2-reactivity are important for furnace performance these features have also been measured.

Jan 1, 2004

By H. S. Benson

This report documents, from concept through field testing, the pan scraper Wheel Slip Monitor. The function of this device is to instantly warn the scraper operator of wheel slip and thus enable him to take immediate corrective action. Knowledgeable pan scraper people recognize that the preponderance of scraper tire damage and wear occurs during useless wheel slip when the scraper operator attempts to increase machine draft beyond what traction will allow. The resultant shortened tire life has become very expensive. The Wheel Slip Monitor reported here provides the means for relieving the scraper operator of attempting to judge wheel slip on tires he cannot see. Direct and intuitively understandable audible and flashing light warnings tell the scraper operator which wheel is slipping and also indicate the relative magnitude of the slip. Beside the Wheel Slip Monitor's patent utility as a real time operator aid, it has unique potential for application to extended term wheel slip history acquisition under field conditions. This information has never been easily available and it promises practical value in pan scraper management.

Jan 1, 1983

By Robinson KJ

There has been much debate in recent years regarding the number of Geology (Earth Science) graduates produced in Australia. The key variable has commonly been assumed to be the placement of graduates in the mineral and petroleum industries. Although not wishing to deny the importance of this element, we contend that Geoscience studies should be given to a wider variety of graduates. The essence is to make students and future citizens more environmentally aware. INTRODUCTION Geoscience is fundamental to exploration and to the well-being of the minerals industry and hence the Australian economy. The value of mineral primary products exports for the past three years has been: 1895 $15.3 billion 1986 $14.8 billion 1987 $16.3 billion (Data source: B.M.R) The mining industry supplies about 40% of Australia's export earnings. However the overall value of Geoscience to the Australian economy is much greater. At the opening of the ANZAAS conference in Townsville during May 1987, Sir Bruce Watson , Chairman of the Mt. Isa Mines Ltd., made a plea for a national re-examination of the way science is taught in secondary schools. In particular he emphasized the point that the community should be more aware of the importance of Geoscience and the value of the mining industry to Australia.

Jan 1, 1989