Search Documents

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By Rolf Birger Pedersen, Alden Ross Denny

"Synthetic Aperature Sonar (SAS) is a powerful tool for ultra-high resolution marine survey. The Kongsberg HiSAS system deployed on the HUGIN AUV has a rangeindependent resolution of 3x3 cm for sonar image and ~10x10cm for the interferometric bathymetry product [1]. This resolution is achievable for areas up to 50 km2 on a single survey mission providing huge multi-attribute datasets. This technology, originally designed for military and oil-industry applications, has the potential to revolutionize scientific seafloor mapping. The extreme resolution of this technique allows for deposit mapping in and around seafloor hydrothermal systems, including the discovery of extinct venting structures. By clearly distinguishing between volcanic and hydrothermal landscapes based on features below the resolution of conventional multibeam systems, SAS enables an entirely new level of hydrothermal deposit survey. Additionally due to the extreme resolution of this survey technology, repeat survey and change detection should allow centimeter-scale changes in deposit morphology to be routinely detected over an entire hydrothermally venting region. In collaboration with the EU funded MIDAS project, the Centre for Geobiology at the University of Bergen will deploy the HUGIN AUV this summer at two distinct shallow venting systems on the Arctic Mid-Ocean Ridge system. The AUV will collect repeat bathymetry at the Jan Mayen Vent Field, and extend the SAS coverage to include newly discovered venting sites. We will present the preliminary findings of this expedition, including the first deposit estimations made from full-resolution SAS mosaics."

Sep 1, 2014

By J. Lehmann, H. Gaye

A brief review of Computational Thermodynamics software concerning the modeling and prediction of reactions involving metals, slags and fluxes is presented. Their application for various steelmaking treatments is discussed. Examples concern phosphorus removal in BOF and EAF, ladle steel desulfurization, and specific treatments for inclusions control in semi-killed or Al-killed carbon and stainless steels.

By J M. Parr, P M. Herzig, J B. Gemmell, S D. Scott

PACMANUS is an actively-forming seafloor analogue of volcanic-hosted massive sulfide orebodies, situated on the crest of an andesite-dacite-rhyodacite ridge overlying rifted older arc crust in a back-arc basin. Hydrothermal deposits range from Mn-oxide crusts to Cu-Zn-rich massive sulfide mounds and chimneys containing significant Au and Ag. Preliminary data suggest a substantial magmatic component to fluids and metal sources, and we speculate that PACMANUS is the cap to a complete hydrothermal system including subvolcanic and intrusive-related mineralisation.

Jan 1, 1995

By N H. S Oliver

Five major veining events have been identified within the area surrounding the Mount Whaleback microplaty hematite deposit. These veining events can be directly correlated to the established deformation history of the Hamersley Province (Brown et al, in press). Vein formation temperatures of 203 to 231¦C have been obtained from primary fluid inclusions within veins which formed around the postulated time of ore formation. Preliminary proton induced x-ray emition (PIXE) analysis of these inclusions indicates KCl is the dominant salt species with varying levels of Ca, Fe, Ti, Mn present. It is suggested that some of these veins may have formed from feeder or effluent fluids from microplaty hematite ore formation.

Jan 1, 2002

By G. Kosick, G. Dobby

CEET, an acronym for Comminution Economic Evaluation Tool, was jointly developed by MinnovEX Technologies Inc. and 13 major mining companies for the purpose of designing and predicting the performance of grinding circuits. It fundamentally differs from other methods by using as its’ data set a geostatistically significant population of hardness data distributed across the mine block model. Historically the characterization of an orebody for the purpose of either designing a grinding circuit or predicting the performance of an existing circuit has been done with a relatively limited number of discrete samples. In addition to power selection, shell sizing, and costing for multiple circuit options, CEET also outputs tons per hour, P80, and operating cost on every mining block for subsequent integration back into the block model. This paper will provide an overview of what CEET is and how it works.

Jan 1, 2001

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By D. B. Felsher

"Lakeshore Gold’s Bell Creek Mill is located in Timmins, Ontario. The mill has been in operation since 2009 and has undergone several small expansions since then. In 2012 - 2013 the first major mill expansion was commissioned raising the mill capacity from 2,000tpd to 3,150tpd. This was done through the installation of a new ROM ore truck dumping facility, jaw crusher, ore storage dome, SAG mill, leach tank, CIL tank, and electrowinning cell. This paper will cover the equipment installed to raise the tonnage as well as the commissioning of the new equipment including problems encountered and how these problems were solved.IntroductionLake Shore Gold acquired the Bell Creek Mill, along with the Bell Creek Mine, from the Porcupine Gold Mines Joint Venture, a joint venture between Goldcorp Canada Ltd. and Kinross Gold Corporation, in December 2007.The Bell Creek mill, which processed ore from the Bell Creek Mine has consistently achieved recoveries of over 95%, is a conventional gold mill circuit, involving crushing and two stage ball mill grinding, gravity and leaching, followed by Carbon-In-Pulp (CIP) process for gold recovery. The facility had been placed on care and maintenance in 2002. At the beginning of 2009, the mill had been refurbished with an initial capacity of 800 tonnes per day and was subsequently refurbished to a capacity of 1,500 tonnes per day near the end of the third quarter of that year. The Mill was then expanded in 2010 to a capacity of 2,000 tonnes per day.In late 2011, the Company commenced a 50% expansion of its milling facility, from a processing capacity of 2,000 tonnes per day to 3,150 tonnes per day. Phase 1 of the expansion, which mainly involved enhancements to the solution circuit (“back end”) and increased the mill’s capacity to 2,500 tonnes per day, was completed at the end of 2012. Commissioning of Phase 2 of the expansion, to a capacity of 3,150 tonnes per day, commenced at the end of July 2013."

Jan 1, 2015

By Stig Eriksson

In Switzerland two major railway systems as shown below in Figure 1 has recently been completed or is under construction: ¦Lötschberg, south of Bern which was commissioned in 2007 ¦Gotthard, south of Zurich which is scheduled to be commissioned in 2016The aim is to increase the transport capacity of the railway system and to transfer more transport of goods to the railway by offering transport of trailers and lorries on the new railway systems. It will have a positive environmental impact but also improve the congested traffic situation of the highways in north-south directionThe Gotthard tunnel is totally 57 km (35 mile) long and the Lötschberg tunnel is 35 km (22 mile) long. Both tunnel systems consist of two parallel single track tunnels connected with cross tunnels at every 333 m (1 093 ft). Additionally there are cross-over tunnels and caverns for installations and operation. In the Lötschberg tunnel, the majority of the excavation has been by Drill & Blast and in Gotthard tunnel the major part is being excavated by TBM.

Gold mining in Australia and globally has a long and variable history. In recent years, due to ongoing public concern over long-term environmental impacts, the mining industry globally has been moving towards a more sustainable framework, presented as the æMining, Minerals and Sustainable DevelopmentÆ (MMSD) framework at the Johannesburg Earth Summit in 2002. There are a number of fundamental issues and concerns with assessing the sustainability of mining. Firstly, long-term trends show that ore grades for almost all metals and minerals will continue to decline (some rapidly so), increasing waste rock is being produced due to the trend towards large-scale open cut mining and more complex ores are now commonly being developed. The impact of these trends on the resource intensity, or unit cost, of gold production is of major concern as it could lead to an increase in energy, water and reagent consumption and greenhouse emissions per unit gold produced. A detailed compilation of these fundamental sustainability indices for gold mining has been undertaken, and is presented with respect to indices over time, ore grade and ore throughput. A clear observation is that the resource intensity of gold mining is extremely sensitive to the ore grade, with energy, water and cyanide consumption and greenhouse emissions rising significantly as ore grade decreases. Based on the gold ore resources at operating mines and other known gold deposits, it is most likely that the average gold ore grade will continue to decline, leading to increased resource intensity and consequent environmental impacts (assuming no breakthrough new technologies occur). These findings are of major importance to understanding the sustainability of gold mining. The final judgement of the sustainability of gold mining therefore must take into account the sensitivity of the ore grade in the resource intensity of gold production.

Jan 1, 2007

By S. B. Bealko

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities, and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies including a fire or explosion, a massive roof collapse, mine inundations, or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life, and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By E. C. Stephens

The eastern Washington— Idaho clay region stretches along the northeast margin of the Columbia basin for 150 mil es. The three better known and developed clay areas are Clayton, Wash., (2 miles north of Spokane); Mica, Wash., (10 miles southeast of Spokane); and Moscow-Deary-Bovill, Latah County, Idaho (about 80 to 90 miles southeast of Spokane) see Fig. 1. Clays from the eastern Washington— Idaho clay area have been mined for more than 50 years. At present Mica, Washington deposits are used by the Gladding—McBean & Co. to make a variety of bricks and ceramic products and Latah County, Idaho clays are used by the A. P. Green Fire Brick Co. to make refractories. The Anaconda Co. made an intensive investigation of the clay deposits in the northeastern Washington-!daho area in 1919 to determine the existence of a supply of raw materials from which alumina could be made. The greater part of the work, which included systematic drilling and shaft sinking, was concentrated at Mica, Wash. This was part of a research project carrted on by the Anaconda Metallurgical Research Dept. under the direction of Frederick Laist and F. Frick and it was terminated in 4920. V. D. Perry, Vice President and Chief Geologist for The Anaconda Co., in 1952 assigned the writer to make a preliminary study of clay and other potential sources of alumina ore in the Pacific Northwest with particular emphasis on those deposits which might be of future importance to The Anaconda Co9s. then new aluminurri plant at Columbia Falls, Mont.

Jan 1, 1961

Viscosity measurements were carried out on slags in the CaO-Cu2O-CuO-MgO-SiO2systemcontaining ~ 63 wt% SiO2in air. The experimental work was carried out over a range of temperatures where the slags were completely liquid. Initial measurements were on a binary CaO-SiO2slag to which incremental additions of CuxO-MgO-SiO2slag with the same silica mole fraction were made. The viscosity-temperature relationship was measured for slags with‘Cu2O’contents of 0.02, 0.19, 0.38, 0.79, 1.69, 2.47, 3.01, 5.31 and 10.0 wt%. The proportions of Cu+and Cu2+in the slags were determined. The oxidation state of Cushifted from predominantly Cu+to Cu2+, with the Cu+/Cu2+ratio of approximately 0.3 for slag with a Cu content above 2 wt%. This is equivalent to Cu1.13O. The trends observed for changes of Cu2+/Cu+redox ratio with slag chemistry were consistent with the literature. Decreasing the CaO content by substituting copper oxide resulted in a decrease in the Cu+/Cu2+redox ratio. The change in ratio corresponded to a shift of the value of x in CuxO from an initial value of 1.8 to 1.1,when the slags contained 10% ‘Cu2O’. In this study, the SiO2content of the slags varied between 64 and 60 wt% as the Cu content increased. The viscosity of the slag containing 10 wt% CuxO was nearly 4.5 times lower than the binary CaO-SiO2slag. As the silica mole fraction (xSiO2) actually stayed constant (0.61±0.009),the results show that CuxO acted as a network breaker. Comparison with other ternary slags with similar silica mole fractions suggest that that addition of CuxO to silicate slags has a stronger effect on lowering the viscosity than FeO or MnO has on a molar basis. Keywords: viscosity, copper, silicate, slags

Jan 1, 2004

By Foster Fraas

The most important lithium resource in the United States is in the form of the feldspathoid mineral spodumene. This mineral has not been used to any important extent as a source of lithium salts or lithium metal, as other more easily decomposed minerals have b en available in sufficient quantity to supply the relatively small demand. The need for cheaper lithium salts for such promising new uses as air conditioning or dehumidification and of lithium feldspar for use in the glass and [ramic] trades has justified the recent work done by the Bureau of Mines on King available, through improved beneficiation and extractive processes, some of the lower grade but extensive spodumene deposits.

Jan 1, 1937

By Foster Fraas

The most important lithium resource in the United States is in the form of the feldspathoid mineral spodumene. This mineral has not been used to any important extent as a source of lithium salts or lithium metal, as other more easily decomposed minerals have been available in sufficient quantity to supply the relatively small demand. The need for cheaper lithium salts for such promising new uses as air conditioning or dehumidification and of lithium feldspar for use in the glass and [ramic] trades has justified the recent work done by the Bureau of Mines on [king] available, through improved beneficiation and extractive processes, some of the lower grade but extensive spodumene deposits.

Jan 1, 1937

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

A research project was commissioned by the Australian Coal Association Research Program (ACARP) to improve the understanding of tailgate strata mechanics and to provide a more rigorous engineering basis for tailgate support design. A deformation mechanism termed æskew roofÆ was defined which relates the regional influence of differential horizontal strata movement (shear) about longwall extraction to gateroads. Confirmation of the mechanism was achieved by field investigations which included measurement of the shear displacement along weak interfaces. Under geological and mining conditions where the skew roof mechanism operated, strata units were found to move progressively further towards the goaf with height into the roof. 3D numerical modelling was used to assess the major geotechnical factors controlling the mechanism and to determine appropriate support strategies within a æskew roofÆ environment including the role of cables versus standing supports. The skew mechanism is considered relevant to; all roadways in the vicinity of longwall extraction including the faceline itself, chain pillar design, and support design.

Jan 1, 2005

By T. Backers

In fracture mechanics modeling the rock mass is seen as the combination of rock material and fractures, which are evident on different scales. The activation and propagation of fractures dominates the stability and performance issues as well as fluid flow potential. Once fractures have started to grow into each other and create through going separations, stability of rock engineering constructions may be violated. Further, as fracture mechanics inherently incorporated a scaling law in the form of the participating fracture length, scaling issues can be more accurately mirrored. This contribution highlights some examples of application of a fracture mechanics based code on some rock mechanics issues such as numerical laboratory experiments, borehole stability or the creation of fluid pathways due to underground constructions. The results show explicitly the creation of fractures and connection of existing ones, and hence the safety and performance issues. It has to be concluded that the basis for frequent application of fracture mechanics on specialized challenges in Geomechanics is laid, and the needs for future developments are defined.

May 1, 2009

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990

By Nick Barton

A recent analysis of 145 TBM tunnels of more than 1000km total length has helped to quantify the time dependence of utilization (U). In fact U = Tm, where T is time in hours and m is a negative gradient of deceleration. In poor quality ground, gradient m has a strong dependence on rock mass quality Q, for example m ˜ -0.5when Q = 0.1. Good investigation is critical for ensuring faster TBM tunneling then drill-and-blasting, which tends not to slow down (in m/hr) as the tunnel length increases. Anew design model called QTBM allows more reliable prognoses be made, and occasionally will disqualify the TBM solution.

Jan 1, 2001