Search Documents

By R Castedo, L. M. Lopez, J. A. Sanchidrian

In 2014 the authors presented results from 13 tests made with two blasting seismographs on a vibration exciter. They measured coupling transmissibility as function of frequency (i.e. ratio of the velocity of the sensor mount to the velocity of the ground motion) from 16 to 200 Hz at one or two vibrations levels (5 mm/s or 0.2 in/s, and 20 mm/s or 0.79 in/s) with mounts freely placed, sandbagged, and anchored to a granite slab firmly attached to the plate of a vibration exciter. As the memory capacity of one of the seismographs prevented to cover low frequencies, e.g. 4-16 Hz, a new measuring campaign has been recently made to extend the study down to 2 Hz. In this campaign, two more techniques, in which the sensor mounts were fixed with thermal adhesive or a combination of duct tape and gypsum plaster, have been also investigated from 2 to 200 Hz at 5 and 20 mm/s. Free and sandbagged mounts lead to a weak coupling of the mounts to rock, so that transmissibility depends on the characteristics of the imposed rock motion (peak velocity and frequency). Measurements are accurate only at low frequencies (below 17 Hz for free mounts and 10 Hz for sandbagged) in the tested conditions (velocities up to 20 mm/s). Above these frequencies, ground motion in the measurement can be modified by a factor of 0.16 to 1.22. Anchored, glued and plastered mounts achieve a stiff rock-to-ground coupling, ensuring consistent measurements for the frequencies commonly found in blasting independently of the vibration level and the mount characteristics

Jan 1, 2015

By Paulo José Costa Couceiro Junior, Manuel Lopez Cano

In 2011, two historic outcrop rocks known as Teffé and Itapema located in the navigation channel of the Port of Santos, Brazil (Latin America’s largest port) – were excavated by drilling and blasting techniques. Sensitive structures - a passenger terminal and an 80-year old warehouse were exposed to ground vibrations generated by underwater blasting. The warehouse had existing structural problems due to a combination of factors such as the presence of an unstable soil, previous repair work, and intense seismic events generated by the daily traffic of cargo trains nearby during eight decades. Since the worsening state of the structure was attributed to ground vibration from underwater blasting, particle velocity time histories generated by underwater blasting and by passing trains were monitored. By analyzing the energy spectral density of these events using spectrograms, it was possible to observe the seismic energy levels in time and spectral domains. Since the hysteretic energy dissipation by structures is related to the duration of the seismic event and the limited dissipation capacity of the structure, one could expect damages to appear in the structure once energy levels exceeded this dissipation capacity. As the quantity of energy transmitted to the structure is proportional to the duration of the seismic event, the transmission of seismic energy to the warehouse structure over time was more significant in the case of the train-induced ground vibrations (several minutes) than those generated by the underwater blasting (few seconds). Thus, for the warehouse, train-induced ground vibrations have a larger impact on the structure rather than ground vibration generated by controlled underwater blasting techniques.

Jan 1, 2016

Results obtained from small scale tests using Australian tin concentrates indicate that metallic tin containing less than 0·1 per cent iron can be recovered by a two-stage process using hydrogen and make-up chlorine. In the first stage the concentrate is ground,. pelletized, roasted, and reacted at 650°C with HCI and H2 to volatilize the tin as SnOI2. The volatilization reaction is conducted with cocurrent gas and solids flow because it was found that the use of cocurrent flow yielded a solids residue substantially free from FeCI2. The second stage uses a technique termed "reflux reduction" during which the SnOl2 produced by volatilization is reduced by hydrogen to form tin and a gas containing HCI and H2 of sufficiently high HCI tenor for recycle to the volatilization stage. The elimination of tin ranged from 98+ to 99·7+ per cent of the tin from concentrates containing 5 to 50 per cent tin, respectively. The process should be capable of continuous operation, and a tentative calculation has shown ,that a treatment rate of 12,000 tonnes of tin concentrate per year could be obtained in a volatilization reactor 1·1 m in diameter and 6·1 m high. The process may have particular application to finely divided concentrates containing less than 20 per cent tin.

Jan 1, 1974

By P. K. Narasimharaghavan

The major threat to the sustainability of Aluminium Industry is its significant contribution to global warming by way of generation of non eco-friendly gases during its production cycle from Bauxite to the finished product. Though reduction measures are taken in control and effective recovery of values from pot room gases, efforts in use of environment friendly additives in the final products production line is warranted. In this line, the present paper describes our efforts in the use of a new generation refining flux which apart from helping in effective removal of alkali metals, reduction in inclusions and ensure a better metal cleanliness shall also aide in reduction of obnoxious gases generated during the metal refining process prior to casting. The aim of the current work was to reconcile the practical results with the old generation fluxes used. Further improvements to bring in a better metal cleanliness will also be discussed.

Jan 1, 2010

By Roy L. Wilfong

The thermal decomposition of the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of praseodymium, neodymium, and samarium was investigated thermogravimetrically in the temperature range 25° to 1,500° C. Each salt was decomposed at a heating rate of 2.5° C, per minute. The pyrolytic sequences have been identified and the temperatures of formation of inter-mediates, the minimum oxide formation temperatures, and values for loss on ignition have been determined. The nonstoichiometric ranges between Pr6011 and Pr203 and the extent of these ranges have been determined for oxides derived from the carbonate, nitrate, and oxalate salts of praseodymium. The alum and sulfate salts of praseodymium produced the sesquioxide without forming the intermediate non-stoichiometric oxides. The temperature limits of formation and regions of stability for the alums and sulfates were better defined than were those for the carbonates, nitrates, and oxalates. The minimum oxide formation temperature increased in the order of samarium, neodymium, and praseodymium irrespective of the anion.

Jan 1, 1962

Choosing the correct delay time for many blasting applications is an important and critical blast design parameter for controlling fragmentation, muckpile shape, swell, digability, throw, ground vibration and airblast. BAl and its affiliates have monitored thousands of full scale blasts in a variety of field conditions, spanning over 15 countries, with sophisticated blast monitoring instrumentation. In some blast environments, a small change in the choice of delay times used had a dramatic and pronounced effect on the overall blast results. In other blast environments, large changes in the choice of delays used had absolutely no effect on the final results in terms of specific outputs. In environments which were sensitive to the delay selection, the type of explosive, dynamic response time of the rock mass (TMIN), integrity of the material, burden and rock mass geometry, all played a very important ,role.

Jan 1, 1998

By P. van Meurs, C. van der Poel

From observations of the linear displacement of oil by water from a porous medium as visualized in transparent models, new insight into the mechanism of vircous fingering, as occurring in the case of unfavorable oil-water viscosity ratios, has been obtained. A mathematical description of the observed phenomena leads to formulas. expressing both oil production and pressure drop across the formation as a func-tion of cumulative water injection with the oil-water viscosity ratio as a parameter. Theoretical results are compared with those obtained from scaled laboratory experiments in sand-filled rubes in which water was injected at the one end and production was obtained from the other end. In the second part of the paper the same principles are used to calculate a more realistic production scheme in which production of oil and water is obtained from wells regularly distributed over the field. Results show satisfactory agreement with production data of an actual oil field. Application of the theory is extremely simple as only a limited number of readily available parameters have to be known and results are presented in an analytical form. INTRODUCTION When oil is displaced from a porous medium by water having a viscosity lower than the oil. the oil-water interface is essentially unstable and has the tendency to break up into what are called "fingers" or "streamers". This Viscous fingering has been noted before by Engelberts and Klinkenberg' and has recently been demonstrated in transparent models by van Meurs-. It is highly questionable whether it is at all possible to perform relative permeability measurements In the laboratory reproducing the same distribution of water and oil in the cores as Present in practice. Therefore, we based our descriptive theory on an idealized model which was "tailored" to the fingering mechanism as observed in transparent models under scaled conditions. This approach was the more attractive, as a highly simplified model had already yielded an adequate description of the process. Though we are aware our theoretical approach can be extended in several ways, it is given here in its simplest form to explain the fundamental principles and to avoid complicated formulas. SIMPLEST CASE OF A LINEAR DRIVE Observations and Theoretical Model In Fig. 1 a series of photographs shows how water penetrates into a formation saturated with an oil which is considerably more viscous than the water. The technique for obtaining these photographs, using transparent models, has already been described?. The fingers can be clearly observed and are seen to be mainly parallel to the flow direction. Note that the contours of these fingers are not smooth but show protrusions of water enclosing oil pockets.

By Hamid Butt

Information Technology ??Advanced Information Technology is dramatically changing information flow within organizations. This enables employees to have information at their fingertips to make informed and prompt decisions. ??Real-time information allows timely analysis, which dramatically reduces cycle times, making organizations faster and more flexible. Business Challenges ??Continual growth of mining and Mine mobile fleet.??Increasing maintenance costs. ??Difficult to identify and troubleshoot equipment problems while equipment is operating. ??New equipment is increasing in complexity and cost. Therefore, each failure results in a greater impact to production and cost. ??Troubleshooting practice is reactive. ??Protect and optimize the use of mining assets to realize maximum business value. ??Maintenance and Operating information is not easily accessible ?no near real-time system that provides complete information.

May 1, 2006

By J. L. Cupp, R. C. Ford, B. R. Romig

The Climax Molybdenum Mine, located near Leadville, Colorado, is the site of a lengthy mining history spanning more than 80 years. In the 1960’s, extraction of molybdenum from oxide ore located adjacent to the massive molybdenite sulfide deposit resulted in the construction of an earthen core dam to impound fine-grained oxide tailing in the Eagle River Valley. Through recognized value of water storage and reclamation opportunities, a tailing removal project was initiated in 1993 to convert the impoundment facilities to a post-mining beneficial land use of developed water resources. An evaluation of the effect residual materials and lake dynamics would have on in-stream water quality was performed. Eagle Park Reservoir stands as a model for future reclamation efforts that involve water delivery to highly sensitive receiving waters. This paper provides a case study on project development, the evolution of water quality assessment, and the regulatory framework that contributed to this project’s success.

Jan 1, 1999

Close spatial relationships between the deposits of the Etheridge Goldfield (23 000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic.This hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so; it is concluded that there is little scope for the discovery of extensions of this field.However, the stratigraphic interval between the postulated source rocks of the Etheridge field and stratigraphically higher host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (Pyritic carbonaceous, and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1981

The applicability of borehole assaying techniques, both conventional and advanced, to orebody evaluation in the mining industry is reviewed and assessed, and the research, development, and demonstration programs necessary to apply the various logging techniques to mining are outlined. At present, the principal method of orebody evaluation in the mining industry is coring. However, coring is costly and time-consuming, and potentially great savings can be realized if all or part of d coring program is replaced by a borehole logging suite specialized to the needs of the particular mining industry. Using a set of 12 minerals, most of which are essential to the U. S. economy, an algorithm is presented for calculating the priority of developing suitable borehole assaying technology to replace all or part of the coring in each mineral industry, The priority is expressed in terms of dollars currently spent for that portion of present orebody evaluation techniques which may eventually be replaceable by in-situ assay techniques. The orebody assay requirements (grades, accuracies, etc.) of the 12 selected mineral industries, as determined from mining industry interviews and published literature, are compiled and represent performance criteria for borehole assaying instruments for the particular industry. Current logging techniques, applied chiefly in the petroleum industry, and advanced assay techniques which are or may be packageable for borehole use are evaluated to determine their performance characteristics. The performance characteristics of the various conventional and advanced techniques are then compared with the performance criteria in each of the 12 mineral industries in order to determine the potential benefit derivable from each technique. Finally, the benefit available from each technique, averaged over the 12 mineral industries, is compared with the cost of development of the technique, to determine the overall priority for investment in research to develop the technique for use in mining. The technology assessment and cost-benefit analysis shows neutron activation analysis in its various forms to have the highest priority for research and development as a borehole logging technique. Other techniques found to be promising include x-ray fluorescence, x-ray diffraction, photoluminescence (optical fluorescence), and infrared spectroscopy. Of the 12 industries considered in the study, those where the need for advanced borehole logging technology is greatest are uranium, copper, gold, and iron.

Jan 1, 1976

By William E. Young

There are many large rhodonite-bearing veins containing manganese in the Eureka-Animas Forks area of the San Juan Mountains in Colorado. The Sunnyside vein is the largest known vein in the area. As observed on the surface, the vein is mineralized over 8,000 feet and attains a maximum width of 200 feet. The average width of the vein and its branches and ramifications is 58 feet in the area that was mapped in detail. The weighted-average analysis of surface and underground samples from the northeastern extension of the Sunnyside vein is 8 percent manganese. Most other known veins in the area have a similar manganese content. The Hidden Treasure vein lies southeast of the Sunnyside-No Name-Mastadon vein. The weighted average of the analyses of surface and underground samples from this vein is 13 percent manganese. Exposures of the Scotia-Silver Chord vein are visible over a strike length of 4,000 feet on Treasure Mountain. Diamond-drill holes show that the vein contains 10 percent or more manganese to a depth of 400 feet. The vein has an average width of 28 feet. The Independence vein is exposed on the surface for a distance of 600 feet and has an average width of 6 feet. Three cut samples taken across the vein had an average content of 20.7 percent manganese. Sampling of the outcrops of eight veins in the Placer Gulch area also indicates manganese. Numerous other veins cropping out in the surrounding area are similar to the outcrop of the Sunnyside vein system mineralogically and are worth investigating.

Jan 1, 1966

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

Author's Note: Since the paper on "All-Flotation at North Broken Hill Limited" was read and discussed, the metallurgical results obtained have conclusively justified the adoption of the All-Flotation treatment.At present the shipping grades of lead concentrate produced from North mine ore range between 74% and 75% Pb, carrying approximately 43 oz. Ag and 4.5%-5% Zn. The lead recovery in lead concentrate is recording 95%-96% of the lead content of crude ore, and the milling and treatment cost on 6400 tons crude ore perweek of 96 hours has dropped to 6s. 3.6d. per ton on ore. With an increased ore tonnage, and with a new mill, considerable further reduction in costs is certain.New flotation machines, with 30 in. vertical depth of overflow (instead of 42 in. depth), are now being tried for the secondary granular treatment, with advantageous results. The treatment to-day is practically the same as that outlined in the paper, excepting that additional concentrate is returned for retreatment in the existing units.(Signed) A. LOWRY.Mr. T. A. READ: The author states (page 356 of Proceedings, No. 79), "The sulphide ore itself was then comparatively coarsegrained, a fact which permitted ready concentration of the galena contents by means of jigs, tables, vanners, etc."

Jan 1, 1931

Results of flotation tests on lead-zinc ore from Broken Hill, N.S.W., confirmed that flotation at pH 9 in the presence of cement gave poorer metallurgical results than flotation at pH 7. Additions of 2 kg/tonne wood raspings [e.g. blackbutt (Eucalyptus pilularis), blue gum (E. saligna), brushbox (Tristania conferta), or turpentine gum (Syncarpia laurifolia)l had little effect at pH 7 but greatly accentuated the deleterious effect of cement at pH 9. This was shown to be caused by e:xtractives (e.g. polyphenols and carbohydrate materials) derived from woods at pH 9. The proportion of extractives, as shown by DV absorbance spectra, increased with increase of pH and was affected by various salts.Additions of 1 kg/tonne Al2(S04)3.16H20 when cement or cement and wood were present showed that metallurgical results obtained by flotation were then very simHar to those in the absence of cement or wood or both. This was ascribed to lower pH values in the presence of aluminium sulphate and possibly to specific chemical effects.Additions of aluminium sulphate appear to offer an economic solution to the problem of treatment of ores contaminated with cemented fill at Broken Hill.

Jan 1, 1974

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

Ensuring the success of a major resource development project, whether in the Gippsland Basin or elsewhere, is typically both a complex and costly process. It is therefore imperative from the point of view of the proponents of such a project - and in particular the financiers - that everything possible be done to minimise administrative confusion and delay in the establishment phase of the project, and to put systems in place which enable the project to run smoothly and efficiently in the later stages of its development and operation. An essential element in this process is ensuring that the project management is able to come to terms with and deal effectively with the relevant planning and environmental laws.

Jan 1, 1992

By E J. Hofmann, J E. Hofmann, A J. Hofmann-Fritz

"With its Head Quarters in Perth, global heavy engineering company Hofmann Engineering is one of the largest family owned engineering companies in Australia. The company has pioneered a number of new manufacturing processes and design improvements for components of large comminution equipment.Some of these innovations are: Innovative design improvements of high pressure grinding roll (HPGR) forged steel tyres. Hofmann Engineering has developed unique patented tungsten carbide stud and edge protection designs which improve wear life and introduce quick and cost effective replacement options to further extend the life of the tyre. Development of forged fabricated mill heads using rolled and welded high tensile steel plate as an alternative to cast conical mill heads. Establishment of Australian capability to manufacture and export up to 42 ft. (12.8 m) diameter SAG mill shells. Techniques for fast track, product improved replacements of cracked or damaged mill gears, including in situ profile & wear measurements of girth gears using portable coordinate measuring machine (CMM) technology, forged rim steel and induction hardening technology. Gear and pinion mechanical drive designs to 24 MW or higher for SAG mills of 38 ft. to 42 ft. (11.6 m - 12.8 m) diameter as reliable alternatives to gearless drives.The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering on large, high powered equipment for both the domestic and export markets.CITATION:Hofmann, E J, Hofmann, J E and Hofmann-Fritz, A J, 2013. Australian innovations in high pressure grinding rolls and large grinding mill manufacture, in Proceedings MetPlant 2013, pp 141-151 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013