Search Documents

By W. E. Robinson

Differences in the composition or chemical structure of the organic material in samples of Uinta Basin (Utah) oil shale were studied relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble organic material (kerogen) present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extracts and upon the aromaticity of the kerogen. Significant differences exist in the chemical composition of the organic material from various strata within the Uinta Basin, some of which were related to burial depth but most were related to source material variations, environmental differences, or other factors. The Uinta Basin samples differed significantly from Piceance Creek Basin and Green River Basin samples in the large amount of soluble extract they contained.

Jan 1, 1975

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By S. Lolon

Spontaneous combustion in underground coal mines has become a serious problem particularly in the caved area (gob). Recent statistic has shown that approximately 17% of total 87 underground coal mine fires in the United States are attributed to spontaneous combustion (De Rosa, 2004). Spontaneous combustion results from a self-heating process in exothermic conditions. The accumulated heat, if not removed, is conducive to the rapid increase of temperature and may result in mine fires or explosions. It is well accepted that the interaction between oxygen and coal substances is the main cause for spontaneous combustion, while other factors such as pyrite, moisture, and bacteria play a secondary role to the self-heating of coal. Therefore, only coal oxidation is considered in this study. Coal oxidation occurs as coal comes into contact with air. This process involves complex phenomena in terms of heat transfer, chemical surface absorption, and energy balance related to inherent properties of coal (Wang et al., 2003). For simulation purpose, overall reactions can be simplified as suggested by Mitchell (1990): C + O2 CO2 + heat [65°- 94°C] (1) CO2 + C 2CO + heat [100°- 150°C] (2) Stoichiometric reactions (1) and (2) show that 2.66 grams of oxygen are required to oxidize 1.0 gram of carbon. Once the temperature exceeds 100°C, the reaction has little chance to stop. The crucial step in reducing spontaneous combustion risk is locating the ignition point of spontaneous combustion (hot spot). This information is useful in the effort of developing a preventive method effectively. In this study, this was conducted based on the best gathered information: ventilation surveys conducted in an existing longwall mine located in the western US; the laboratory experiments performed on a physical gob model; and the CFD models to investigate the flow behavior in the gob, the oxidation of coal, and heat transfer phenomena. The hot spot location is determined as a function of oxygen concentration and gob temperature. The critical values are the following: 5% (by volume) for oxygen and 100°C for gob temperature. CHARACTERISTICS OF GOB MATERIAL AND MODELS Permeability Concept Permeability is one of the key parameters in any study dealing with porous medium. This is determined by particle size and the ratio of void volume to the total volume (porosity) of porous medium. This relationship is known as the Carman-Kozeny equation (Scheidegger, 1957) and is given mathematically as [ ] where k* = theoretical specific permeability, m2 dm = the mean particle size, m n = porosity However, permeability tests with various particle sizes were carried out at the University of Utah?s ventilation model (Figure 1) to verify this relationship. These tests indicated a necessity to modify this theoretical relationship. A factor of 0.898 was obtained to make up the different between theoretical permeability and the experimental one. The modified version of (3) is given by: [ ] This equation is used to determine permeability of the simulated mine gob throughout the study. [ ] Mine Gob Material The gob is represented by zones filled with material of given size distribution. For physical measurements and CFD simulations, the material used were crushed rock and coal. Due to compaction, three different characteristics of gob material were used in the model: unconsolidated, semiconsolidated, and consolidated. In the real condition, the largest coal-rock particles are more likely to be located in the area behind the shields. This material is freshly broken and unconsolidated. The size of these broken particles is based on a study carried out by analyzing images taken from the area behind the shields in three coal mines in the United States (Pappas and Mark, 1993). The results have shown that the mean size of materials behind the shields is about 1.22 m. The permeability associated with this size was then obtained from (4) and permeability tests. This was 4.68 x10-7 m2. For semiconsolidated and consolidated zones, due to the lack of experimental data, these were determined through CFD simulations. These simulations were designed by assigning a permeability of 3.15 x 10-8 m2 for consolidated zone and 7.98 x 10-9 m2 to the other zone. The airflow pattern in the gob assigned with given permeabilities was expected to follow the experimental distribution (Brunner, 1985). The mean particle sizes for the semi-consolidated and consolidated zones were 0.02 and 0.006 m, respectively; smaller than those of the unconsolidated zone. Figure 2 shows the 3D view of permeability changes in the gob.

Jan 1, 2009

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

By Aram Grigoryan

This paper addresses the challenges of designing the underpinning of major sub-way station with 4 operating tracks. No. 7 subway extension crosses under the existing 42nd street subway station on the 8th Avenue line. Understanding the history of the original construction, of the current structures and their condition were instrumental in developing a feasible underpinning design that is integrated with the design of the new tunnels. The existing 8th Avenue subway station has a lower abandoned level. Several alignments and corresponding underpinning schemes were studied. The design allows new tunnel construction under the station without interruption of station operations.

By P. Wells

"In the past decade, there have been many developments in processing of nickel/copper sulfide ores. Improved pentlandite/pyrrhotite flotation selectivity with the use of new reagents, fine regrinding and Redox measurement (control) has led to increased pyrrhotite rejection and thus higher concentrate grades. Flash flotation has increased overall nickel and associated precious group metal recoveries. Recovery of both fine and coarse particles has been improved through an understanding of flotation cell hydrodynamics. The separation of copper from nickel in such ores has seen a similar level of development. From the late 80s to very recently, the use of flotation columns, the use of pyrrhotite depressing reagents and the improved understanding of the complex mineralogy of chalcopyrite, pentlandite and pyrrhotite have considerably increased copper / nickel separation efficiency. Copper concentrate with more than 30% copper and less than 0.5% nickel grade is now obtainable at 80-85% copper recovery from mill feed compared to 70-75% copper recovery with 30% copper and 1% nickel grade only a few years ago. Improved copper / nickel separation in milling operations has the potential to substantially improve the processing of the resulting concentrates and thus the overall return from the extraction of nickel and copper from sulfide ores.INTRODUCTIONNickel metal by itself or in alloys with other metals and materials makes a significant contribution to modern society. The relatively high price that nickel commands compared to other base metals is a reflection of the fact that, although abundant in the universe, nickel is sparingly distributed in the earth’s crust. There are two types of nickel deposits that are currently being exploited: complex sulfide ores and lateritic oxide ores. Lateritic contain no copper but in sulfide deposits, nickel– bearing minerals, principally pentlandite (Pn, [Ni,Fe]8S9), some millerite (NiS) and violarite ([Ni,Fe]S) are often found in association with copper-bearing minerals, mainly chalcopyrite (Cp, CuFeS2) and cubanite (CuFe2S3). The copper content of such ores can vary considerably from as high as 5-8% (in some Sudbury basin ores) to as low as 0.1% (in ores mined by Western Mining at Mount Keith, Western Australia and by Inco in Thompson, Manitoba). The valuable minerals Pn and Cp are almost invariably found associated with pyrrhotite (Po, Fe7S8) which along with nonsulphide rock has to be rejected to tails in the primary milling stage. The bulk concentrate from the primary stage is then treated to depress Pn and float Cp. A complete Cu/Ni separation at the mill would be highly desirable but this is not possible because of locking between a small fraction of the valuable minerals. As a result, Cu/Ni separation has to be carried out both during milling and during refining of the matte following smelting. At Inco, Jinchuan and in Norilsk, a chalcocite / heazlewoodite separation is made by flotation following slow cooling of the matte. In the present Sudbury Inco operations, Cu/Ni separation has not been conducted at the mill since 1991 and all Cu/Ni separation takes place at the matte processing plant. Because of the rising ratio of Cu to Ni in the ore, this strategy is under review and this paper describes some recent studies of circuits in preparation for possible installation of a copper / nickel separation circuit at Inco’s Clarabelle Mill in the Sudbury area."

Jan 1, 2004

By Gale D. C, Giles D. E, James Parker A

A zinc-lead-iron sulphide concentrate from McArthur River can be leached at atmospheric pressure in aqueous solutions with HCI, FeCl3, CuCI2, HCl/02 HC1/02/ CuCI2, Cl2, and CI2/CuCI2 to extract >98 per cent zinc, >90 per cent silver, and <15 per cent iron in 1-7 h at 95°. Galena is more reactive than sphalerite and is converted to lead chloride. Except for leaching with HCI, elemental sulphur is the the main by-product of the leach with little or no sulphate ion detected. The rates and products of these reactions are compared. It is recommended that aqueous slurries of the concentrate (50 per cent w/v) are leached at atmospheric pressure with Cl2 in the presence of copper(II) chloride, which accelerates the extraction of zinc. Hydrochloric acid is a by-product which is consumed bYJeaction with fresh concentrate in air at 60°. Copper is subsequently stripped from the leach solution and recycled by reaction with fresh concentrate at 100°. The separation, recovery, and electrolysis of zinc and lead chloride is outlined since this process would produce Cl2 gas which can be recycled and used directly in the leaching stage.

Jan 1, 1976

[United Engineering Trustees, Inc. ALBERT ROBERTS. '47 R. M. ROOSEVELT, '49 RALPH B. WILLIAMS, '48 The Engineering Foundation F. F. COLCORD. '46 M. A. PRENTIS. Jn.. '48 It. >I. ROOSEVELT. '49]

Jan 1, 1946

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane5, a new refrigerant that has a remarkably low toxicity. Continued research by the Prigidaire Corporation6 and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati7 revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical-and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

By Michael B. Gilbert

The Woodbury L-73 Tunnel involved the design and construction of a 96-inch tunnel driven through 8,080 lf of very difficult ground conditions. Anticipated ground and groundwater conditions consisted of potentially flowing silty sand with cobbles and boulders, mixed face of sand and sandstone and full face of the St. Peter Sandstone. Actual conditions were similar, although the quantities did change from bid quantities. This paper presents the approach used for development of the GBR regarding risk management. The means of arriving at a fair compensation for variances from the baseline values to address the actual encountered tunneling behavior of the soil, boulder count and its effect on production rates are presented.

Jan 1, 2008

By B. D. Pandey, D. Bagchi, Premchand

During the separation and recovery of metals from the ammoniacal leach liquor of Indian Ocean nodules by solvent extraction-electrowinning (SX-EW) in close-loop operation, the copper electrolyte containing ~40g/L Cu, 20 g/L Ni and 180 g/L sulphuric acid is bled-off to control the impurities. The recovery of copper and nickel as powders has been examined from the copper bleed solution following partial decopperisation, crystallization of mixed sulphate of the two metals and aqueous hydrogen reduction. From the dissolved sulphate solution containing 17.68 g/L Cu, 18.83 g/L Ni and 0.03 g/L Fe, the copper powder was precipitated at initial hydrogen pressure of 26 bar in an autoclave in 90 min at 140 °C. The residual copper from the spent solution was removed as sulphide and nickel powder was then recovered (99%) in two stages from a solution of pH 4.5 at 40 bar pressure and 190 °C. However, 98% nickel recovery in one stage was achieved when hydrogen reduction was carried out from an ammoniacal solution in the pH range 9-11. Copper and nickel powders were produced from the bleed solution with acceptable purity and specifications suitable for P/M applications.

Jan 1, 2004

By Eric Konigsmann, Doug Spence, Scott Jones

"The Williams Gold Mine is located in the Hemlo camp of Northwestern Ontario and is one of Canada’s largest gold producers with annual gold production of 400,000 ounces. The operation is owned and operated as a 50:50 joint venture between Teck Cominco Limited and Barrick Gold Corporation.In July 2002, the decision was made to introduce paste backfill produced from mill tailings as the primary backfilling method in the mine and to decommission the existing cemented rock fill system. This required a fast track design to be completed for both a surface paste backfill plant and an underground paste distribution system followed by an intensive construction phase through the fall and winter of 2002/2003. The paste system was commissioned on schedule in late April 2003 and was in full production within 4 weeks of the initial start up. Overall, the project duration was only 42 weeks from initial project release to commissioning and it was completed $2 million under the budget of $14 million.This paper presents an overview of the lab testwork and process flowsheet design, process control methodology and describes the construction and commissioning phases of the project. Preliminary paste plant performance and operating cost data is also presented.IntroductionThe Williams Gold Mine is located in Northwestern Ontario adjacent to the Trans Canada Highway in the Hemlo Gold Camp as shown in figure 1. The mine currently produces approximately 400,000 ounces of gold annually and is owned and operated as a 50:50 joint venture between Teck Cominco and Barrick.The deposit was discovered as part of the Hemlo gold discovery in 1981 which led to the development of three mining operations within a 2 kilometre radius. The neighboring operations are the Golden Giant Mine, currently owned and operated by Newmont Gold, and the David Bell Mine, currently owned and operated by the same joint venture which is running Williams. David Bell ore is blended and milled in the Williams concentrator."

Jan 1, 2004

By Patrice Favreau, R. F. Ph. D. Professor Emeritus Favreau

After Nobel invented dynamite, blasts were carried out by trial and error, without the use of equations based on the fundamental principles of Chemistry and Physics, although everyone accepted that shock waves were involved; but no equations were available to calculate their intensity. Around 1950 however, M.A. Cook proposed a procedure to calculate the thermochemistry of an explosive, and thus evaluate theenergy released during the explosion of a fully confined explosive. Some blasters then began to use theEnergy Factor; the latter, however, does not subdivide the energy into its three kinds of activities necessaryfor a successful blast, as demonstrated in 1968 by reference 2, namely i) the shock wave which weakensthe rock; ii) the stress field SS which fully fragments the rock; and iii) the release of the stress SS whichcauses the fully fragmented rock to burst out with the velocity necessary to move the rock into the muckpile. The article explains that the way to achieve a successful blast is by insuring that the explosive energy divides properly into the weakening action of the shock wave which is necessary to prevent large collar blocks and toe, and into adequate stress field intensity SS which is necessary to obtain good fragmentation size distribution at the crusher, as well as adequate burst out rock movement to achieve easy mucking.

By M. Mets

Pile foundations have been used in Estonia since the beginning of 1960's. To evaluate the capacity of piles nearly 2,500 pile tests and 1,800 pile loading tests Have been carried out. The pile foundations of nearly 150 houses are under settlement observations.

Jan 1, 2000

By Robert Blickensderfer

Tungsten alloys with high-temperature strength properties, comparable to the best of alloys recently developed by others, were produced by a new process called here the oxyreaction process. The process involved additions of a powder of a reactive metal compound, ZrN, ZrW2, or HfW2, to a base metal powder, tungsten, which contained some oxygen. The powders were blended, compacted, sintered, and extruded. During sintering, diffusion and internal oxidation occurred to produce reactive-metal oxide particles and solid solutions. A dispersion of oxide particles could be precipitated by heat treating. The oxyreaction process circumvents many of the agglomerating and coarsening problems encountered in the current methods for dispersing a stable oxide in a metal. Oxyreaction strengthening results from solid-solution strengthening and from dispersion strengthening produced by the reactive metal and its oxides. At a test temperature of 1,650° C, the alloys prepared from WW, had tensile strengths up to 70,000 psi and stress-rupture lives up to 142 hr at 10,000 psi stress; the alloys prepared from ZrN powders had tensile strengths up to 80,000 psi and stress-rupture lives up to 27 hr at 10,000 psi stress. Tensile strengthening in the alloys was attributed to Zr in solid solution or to Zr-O-W structures too small to be observed in an electron microscope replica. Stress-rupture life was attributed to a dispersion of submicron Zr02 particles which precipitated and grew to 0.05-to 0.2-micron size during the test. Tensile strengthening and stress-rupture life were dependent upon both the zirconium and oxygen contents with the maximum occurring at roughly 0.9 atomic pot Zr and 0.9 atomic pot 0. Studies of the details of the oxyreaction process were made on the W-ZrW2 alloys and three general steps were determined: (1) The reaction of 0 in tungsten powder with ZrW2 to form relatively large Zr02 particles; (2) the dissolution of remaining ZrW2 into the W matrix and partial internal oxidation to form ultrafine but sparse zirconium oxide particles and possibly to establish Zr-O-W structures; (3) the development of ultrafine Zr02 particles during high-temperature aging.

Jan 1, 1971

By Bas R. Hemmen

GeoBrain is a facility at GeoDelft with the purpose to provide society with all relevant geo-engineering knowledge and experience in a structured way. On the basis of the available knowledge and experience engineers, decision makers and construction supervisors can come to a fast, reproducible and objective choice, taking into account the consequences. The paper presents examples from the GeoBrain experience databases and forecasting models developed for foundation engineering and directional drilling, or: "GeoBrain Foundations" and "GeoBrain Drilling". GeoBrain is closing the gap between theory and practice. It is aimed directly at reducing uncertainty and the costs of failure, thereby increasing the quality of profession and minimising the risk in geo-engineering works.

Jan 1, 2006

By James E. Aplin

Previous studies have shown that fracturing of roof strata precedes ultimate failure, and that the fracture development causes an accompanying increase in the apparent resistivity of the strata. Using this principal, a microprocessor controlled resistivity roof fall warning system (RRFWS) was developed that automatically sequences through and records up to 32 electrodes that may serve as either voltage or current electrodes. This capability permits increased coverage with a minimal number of required electrodes. The data is stored in a nonvolatile memory and on an optional printout, making the system nonsusceptible to loss of mine-power. To further save battery power, the system's electronics shut down between readings, except for a carbon molybdenum steel real-time clock. At a preprogramed interval, the RRFWS reactivates and repeats the sequence. If the absolute change or the rate of change of resistivity exceeds a predetermined limit the system is capable of sounding an alarm. In addition to the monitor, a stainless steel mod led split-set electrode was also developed that permits long-term corrosion-free contact.

Jan 1, 1983

By L. F. Heising

This report is a general summary of pertinent data on the manufacture and use of synthetic ammonia products. It provides a condensed summary of the potentialities of a synthetic ammonia industry in North Dakota for Federal, State, and private organizations that may be interested in helping to develop an integrates synthetic ammonia and fertilizer industry. The report contains discussions of: (1) Materials used in the manufacture of nitrogenous fertilizers, nitric acid, and urea; (2) National production, imports, exports, and consumption; (3) the ammonia industry, location, capacity of plants; (4) processes used in manufacturing synthetic ammonia, nitric acid, and urea; (5) other potential industries; and (6) analyses of manufaturing and plant cosh;. Additional information on industrial compounds from ammonia and plant nutrients removed by crops is given in Appendixes 1 and 2. Synthetic ammonia is one of the primary ingredients in fertilizers. Resources required in synthetic ammonia manufacture are available in North Dakota. Hydrogen is available from the petroleum and natural gas resources, particularly in the Williston Basin, and from the large lignite resources in the State. Hydrogen can be produced from lignite by a gasification process developed by the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1954

By T. Seal

Hydro-Jex© releaching was undertaken during the summer of 2010 at the Valley Leach Facility (VLF) at AngloGold Ashanti?s Cripple Creek & Victor Gold Mine. Several advancements to the technique were made in response to the technical design and operational challenges posed by the unique site conditions. New geophysical resistivity monitoring techniques were developed to monitor solution migration during the injections. These developments are presented along with discussion of gold production resulting from the project.

Jan 1, 2011

By C. H. Manney

This report deals with the feasibility of the use of vocoders as an integral part of a mine electromagnetic voice communication system. Limitations imposed by the nature of the transmission path, background noise and equipment are examined. Some properties of vocoders and apparent advantages of the use of vocoders in a mine communication are discussed. The conclusion is reached that the man-made noise level will ultimately determine the workability of such a system.

Jan 1, 1972