Search Documents

By C. W. Binckley, F. R. Burgess, E. R. Haymaker

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By E. R. Haymaker, C. W. Binckley, F. R. Burgess

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By G. R. Smithson, John E. Hanway

This paper, the first of two papers covering the development of a metallurgical process for the treatment of a complex ore, describes the bench-scale experimental Program undertaken as a basis for initial process design. The results of using various potentially applicable process steps are detailed and the basis for selecting certain of these steps for Pilot-plant development is outlined. A process consisting of the steps of sulfate roasting, leaching, copper recovery, solution purification, zinc electrolysis, and brine leaching for lead recovery was recommended for further study. THIS paper describes the bench-scale development of a sulfate roasting process designed to recover copper, lead, and zinc from a complex ore. The extrapolation of the bench-scale results to pilot-plant design and the results of pilot-plant operation will be described by Lund, et al.' in a subsequent paper. Several years ago, the research divisions of the St. Joseph Lead Co. became responsible for the development of a metallurgical procedure to treat a complex sulfide ore containing copper, zinc, and lead sulfides. The primary objective was to devise a procedure which would permit economic recovery of the nonferrous values. As could logically be expected, the study of conventional flotation procedures was undertaken; in addition, however, because the physical nature of the mineral association in the complex ore indicated that physical methods of ore beneficiation might not prove to be entirely satisfactory, a program also was established to investigate alternative methods of direct metallurgical treatment for recovery of the metal values. Exploratory test work by the St. Joseph Lead staff led to the conclusion that a sulfate roasting technique represented the most attractive approach for a direct metallurgical process. Sulfate roasting would provide for the selective conversion of the nonferrous values to forms soluble in conventiona1.1 leaching agents and would permit their efficient separation from the insoluble iron and other gangue materials. It should allow efficient utilization of the thermal energy available from oxidation of the sulfide raw material, and might provide an opportunity for recovering byproducts such as iron and sulfur. The decision to evaluate a selective sulfation procedure as a basic processing step also was influenced by the excellent results obtained by the St. Joseph Lead Co. in using this procedure for the recovery of cadmium from zinc sulfide concentrates. The choice of selective sulfation as a major processing step served as a basis for an extended experimental investigation of the process with bench- and pilot-scale equipment to prove its feasibility. St Joseph Lead Co., aware that Battelle Memorial 1nstitute had participated in the development of several fluidized-bed sulfate roasting procedures, asked Battelle to undertake the bench-scale development of a suitable sulfation process. This paper describes the procedure used and the results obtained at Battelle in the treatment of the complex sulfide ore. EXPERIMENTAL WORK Nature of the Raw Material. The sulfide ore deposits of interest are essentially a massive sulfide, with the indivudual ore minerals being extremely fine grained and intimately intergrown with each other and with the associated gangue. The zinc in the ore is present mainly as sphalerite (ZnS), the lead as galena (PbS), and the iron either as pyrite (Fes2) or as pyrrhotite (FeS). Table I shows the chemical analysis of various individual samples of the ore. These analyses illustrate the variability of the ore body and impose a rather severe requirement on any type of metallurgical process—that of being able to tolerate probable wide variations in the assay of the head ore. The tentative flowsheet designed to serve as a guide for the initial experimental investigation of

Jan 1, 1962

By P. H. Turnock, R. D. Pehlke

The effects of mutual interactions between elements on the solubility of nitrogen in liquid iron alloys containing chrormium, columbium, molybdenurn, nickel, or silicon have been determined. The equilibrium nitrogen solubilities in the liquid iron alloys were measured by the Sieverts method. The second-order effects caused by the presence of chrormium, columbium , or silicon in the melt were found to be significant. The solubility of nitrogen in liquid iron alloys containing several alloying elements has also been measured as a function of melt temperature and nitrogen pressure. The heat of solution of nitrogen in microcomponent iron alloys has been found to be a function of the logarithnz of the activity coefficient of nitrogen, irrvespectilje of the composition of the melt. The heat of solution of nitrogen in pure liquid iron was determined to be 1265 ± 450 cal per g-atom of N over the temperatxue range 1600° to 1800°. Sieverts ' law was obeyed for all melt compositions studied in the pressure interval 0.4 to 1.0 atm. The solubility of nitrogen in liquid pure iron and in many dilute binary liquid-iron alloys has been the subject of many investigations. Pehlke and Elliott' made a comprehensive investigation on this subject in which they summarized and compared previous researches. However, the practical application of these solubility studies requires prediction of the nitrogen solubility in the multicomponent alloys encountered in operating practice. The interaction parameter as defined by wagner2 has been used to predict the behavior of a solute in a complex alloy, and a modification of this approach has met with reasonable success in several instances.'1"5 The necessity for extending the nitrogen solubility data on binary alloys is caused by the lack of direct measurements of the solubility of nitrogen in molten alloy steels. A direct comparison between measured solubilities and those predicted for multicomponent alloys based on data in binary systems has been made in only a few instances, and most of these were reviewed by Langenberg,6 who developed a graphical technique for predicting nitrogen solubilities in multicomponent iron alloys. The solubility of nitrogen has also been studied over the entire Fe-Cr-Ni ternary system by Humbert and Elliott.? Both studies compared the solubilities computed from binary iron alloy data with those measured in ternary alloys in the liquid state at 1600°C. Most of the nitrogen solubility measurements referred to above were for iron alloys at 1600°C; thus, the ability to predict nitrogen solubilities in molten iron alloys has been restricted primarily to alloys at 1600°C. Recently, Nelsson8 devised an approximate method for calculating the change in nitrogen solubility in molten iron alloys as a function of temperature, but an assumption of regular solution behavior limits the applicability of the method. Chipman and Corrigan9,10 have developed an empirical correlation. based on the activity coefficient of nitrogen in the iron alloy at 1600°C, which facilitates the estimation of nitrogen solubilities at higher temperatures. This method also has limitations, due to the necessity of calculating the activity coefficient for nitrogen in a multicomponent iron alloy at 1600°C from the nitrogen solubility data for binary iron alloys. The shortcoming of such a straightforward approach to the problem of predicting nitrogen solubilities is the disregard of mutual interactions between elements in a complex iron melt. This investigation was conducted in an attempt to provide a more reliable method of predicting nitrogen solubilities in multicomponent iron alloys. The effects of the mutual interactions between chromium, nickel, silicon, molybdenum, or columbium in iron were studied, using the Sieverts' technique1,7 to measure the effects of alloy composition, temperature, and pressure on the solubility of nitrogen in ternary liquid iron alloys.

Jan 1, 1967

By L. W. Holm, A. K. Csaszar

A series of laboratory experiments was conducted in which oil was displaced from a porous medium by water-driven slugs of alcohols or similar solvents. The solvents used were soluble to some degree in both oil and water and covered the range of solubilities from complete solubility in oil to complete solubility in water. Displacement experiments were conducted on 2-and 3%-in. in diameter consolidated cores and 1-and 2-in. in diameter unconsolidated sand packs. The cores and sand packs ranged in length from 1 to 30 ft, and they were saturated with brine and crude or refined oils. The solvents used included ethyl alcohol, isopropyl alcohol (IPA), tertiary butyl alcohol (TBAI, secondary butyl alcohol (SBA), n-amyl alcohol (NAA), methyl ethyl ketone, acetone and others. It was found that all of the oil present in a porous medium could be miscibly displaced by injecting a slug of mutual solvent and driving it with water. The oil-recovery efficiency was dependent upon (1) the relative solubilities of the solvent in oil and water, and (2) the distance traversed by the flood. For complete oil recovery from cores, a smaller amount of a preferentially oil-soluble solvent was required, compared to the amount of preferentially water-soluble solvent needed. The size of the solvent slug required varied inversely with the linear flooding-path length raised to the 0.65 power. Water-driven dual solvent combinations (an oil-soluble solvent slug followed by a water-soluble solvent slug) were found to effect complete oil recovery with less total solvent than any single solvent used. In these dual-solvent displacement experiments, the slug size required varied inversely with length raised to the 0.55 power. Based upon the experimental results, a theory was developed to describe the displacement of oil and water by mutual solvents, and equations are presented to predict the production history in a linear system. These equations take into account the properties of the solvents and the porous medium. INTRODUCTION Oil-recovery processes which utilize displacing fluids that are miscible with the reservoir fluids have been studied extensively in recent years. Because of the poor contact efficiency and high pressure requirements of the LPG-gas displacement process there has been considerable interest in the alcohol-water process, and a number of studies have been made on the recovery of oil through the use of solvents which are mutually soluble in oil and water. An investigation by Sievert, Dew and Conleyl indicated that the use of mutual solvents would be limited because the presence of water in a porous medium would cause a phase break in the leading edge of the displacing solvent. Their study also showed that, in consolidated cores containing. only oil, the displacement of oil by a water-driven mutual-solvent slug of tertiary butyl alcohol (TBA) was affected by the viscosity ratios of the fluids involved. Gatlin and slobod3 concluded that an isopropyl alcohol (IPA) slug acts as a miscible piston, completely displacing both oil and water until the alcohol content of the mixing zone falls below the concentration necessary to maintain miscibility. Their study was conducted on uniform unconsolidated sand packs. They concluded further that IPA could be used effectively to recover oil from a watered-out sand. In a paper by Taber, Gamath and Reed4 relating an investigation on sandstone cores, it was stated that the displacement of oil by mutual solvents, particularly IPA, was not a miscible displacement and that no improvement in efficiency could be expected with increase in flooding-path length. However, their analytical analysis of the displacement mechanism using TBA is, in fact, one which indicates that the displacement is controlled by miscible mixing. They suggested that the lack of improvement in efficiency with flooding - path

By S. J. Matas, R. F. Hehemann, R. H. Goodenow

The hot-stage metallographic method has been employed to determine radial growth rates of upper and lower bainite. Lower bainite appears to grow as individual plates that increase in both length and thickness while upper bainite grows as sheaves of closely spaced plates or needles. A discontinuity in the temperature dependence of the growth rate appears to be associated with the transition from upper to lower bainite and stepped quenching experiments suggest that lower bainite will not continue to grow when the temperature is raised to the upper range. Thus, a single process does not appear to control the growth of both upper and lower bainite. A tentative model based on the forces acting on a dislocation interface is proposed to account for the slow growth of bainite. It has been recognized since the early studies of Davenport and Bain that a close relationship exists between the martensite and bainite transformations in steels. However, diffusion of carbon during the transformation has lead to considerable controversy concerning the reaction mechanism.1-7 Many studies4,5,7-9 have emphasized the structura and kinetic aspects of the bainite reaction and, in particular, the difference observed between the two forms of bainite—frequently termed upper and lower bainite. A kinetic difference between the two types of bainite has been revealed in the activation energy determined from the overall reaction;4,5 however, many difficulties arise in an interpretation of these activation energies since a number of temperature dependent factors contribute to the kinetics of the overall reaction. The displacive surface relief10 accompanying the bainite reaction permits a separation of the nuclea-tion and growth contributions to the reaction and allows the kinetics of the growth process to be examined. Several investigations of this type have been conducted; however, they have been restricted to the low temperature range.3'6'11 Here, bainite plates are observed to grow slowly in both length and width. The present investigation extends such studies to include the upper bainite range. MATERIALS AND PROCEDURE Materials. The composition of the steels studied in this investigation are presented in Table I. The range of composition permitted a study of the effect of carbon content on the growth rate of upper bainite in the 9 pct Ni steels and consideration of both upper and lower bainite in the higher carbon steels. These steels were received as hot-rolled rounds and were forged to approximately 1/2 in. thick plates for preparation of metallographic specimens. In order to produce an essentially zero carbon steel, Steel A was decarburized in wet hydrogen at 1550°F for 15 days with the result tabulated as Steel AD. Experimental Procedure. In order to study the slow growth of the displacive transformation product, a commercially available Leitz hot stage was modified to permit heating of the specimen by its own resistance in a manner similar to that employed by other investigators.6 The furnace chamber was maintained at a pressure of 2 to 3 X 10-5 mm Hg prior to austenitizing at 2000° ± 12° F for 5 min. Samples could be cooled from the austenitizing to the transformation temperature in approximately 15 sec and the progress of transformation was recorded with a 9 cm by 12 cm single frame camera or a 16 mm movie camera. RESULTS AND DISCUSSION Growth Characteristics. The general growth characteristics observed in this investigation were analogous to those reported previously.3,6,11 Typical growth sequences for the high temperature and low temperature forms are illustrated in Figs. 1 to 5. In both temperature ranges, bainite plates increase in length at slow, temperature dependent rates until interrupted by a grain boundary, another plate, or

Jan 1, 1963

By C. E. Birchenall, G. Derge

IN studying the kinetics of slag-metal reactions, it has become increasingly apparent that a complete knowledge of all aspects of interface phenomena will be required to clarify these processes adequately. A part of the data required for all oxidizing slags used in the refining of impure iron to steel is the rate of exchange of iron between the slag and metal phases. The simplest equilibrium of this type is that between liquid iron and iron silicate slag when both phases are equilibrated with the silica crucible containing them. In this study, the exchange of iron between the two liquid phases has been measured by using radioactive Fe as tracer. The observed high exchange rate indicates the ease with which such interfaces may be crossed in refining processes. The experiments required for this study involved relatively minor and normal modifications of well established techniques. Melting was accomplished by induction heating in heavy walled, fused silica, rotating crucibles." Rotation was used to minimize dilution of the slag by crucible erosion. The melting stock was ingot iron. Slags were prefused in iron crucibles using chemically pure grade oxide reagents. The special conditions applying to the active iron additions will be described for individual experiments. Suitable precautions were observed with regard to protection against radiation hazards.' Identification of Activity This particular study was initiated several years ago, but held in abeyance because the radioactive iron available at that time contained a foreign activity which concentrated in the slag so as to mask the iron activity and render the results unin-terpretable. With the benefit of experiences from other studies, radioiron of suitable purity can now be prepared. As received from the Isotope Div. of A.E.C., the unit appears to contain Fe + Fe50 and a high activity cobalt. The cobalt and iron are separated by repeated ether extractions, and the purified iron stored for sufficient time for the Fe'7 44 day half-life) to decay to negligible activity, leaving only Fe as the active isotope. This was confirmed by the absorption curves for slag and metal samples from heat No. 1. In Fig. 1 the experimentally measured points for the absorption curves of slag and metal are fitted by the calculated slope of 5.8 mg per sq cm in aluminum, which corresponds to the Mn K doublet emission resulting from the capture of an orbital electron of Fe" by the nucleus. This shows that the radioactive species are the same in both slag and metal and identifies it as Fe55 Description of Individual Heats For the first heat, the radioactive iron was contained in the prefused slag. The active Fe55 had been precipitated with carrier and was added as Fe2O3 during fusion in the iron crucible. The charge of 500 grams of ingot iron was melted, the protective iron sleeve added, rotation started, and a prefused, inactive slag was added to allow the system to approach equilibrium. After about 5 min at temperature, the wash slag was skimmed and the active slag added. Initial slag and metal samples were taken as soon as the slag was molten. Additional samples were taken at indicated intervals thereafter. Slag samples were dipped with a small iron spoon and metal samples were sucked into 1/4 in. ID silica tubes. The slag and metal samples were pulverized and mounted for radioactive counting. The slag samples were analyzed chemically for FeO. Temperature was read after the last slag sample by immersion of a Pt-Pt-Rh thermocouple protected by a fused silica sheath. Since no significant variation of rate with temperature was observed

Jan 1, 1954

By W. S. Hyler, W. L. Bruckart

The powder metallurgy and arc-cast types of wrought molybdenum stock were studied in rotating beam fatigue. Endurance ratios of unnotched specimens after 5x10 cycles were found to be 0.74 and 0.81, respectively. Fatigue notch factors (K,) of 1.36 and 2.05, respectively, were obtained on V-notched specimens having a theoretical stress-concentration factor Kt = 3.1. MOLYBDENUM and its alloys are rapidly gaining importance as engineering materials of construction for high temperature applications. AS a wrought material, molybdenum and its alloys are outstanding above 1800°F. It is necessary, however, with molybdenum to provide elevated temperature oxidation protection. This is currently being studied by a number of investigators. Thus far, there have been no published data on the fatigue behavior of molybdenum either at room temperature or at elevated temperature. The knowledge of fatigue behavior, particularly notched fatigue behavior, becomes increasingly important as the engineering importance of a material increases, especially from the design standpoint. The work described here was directed toward determination of the notched and unnotched rotating beam fatigue characteristics of molybdenum at room temperature. Also, it was desired to learn whether any difference exists between wrought molybdenum of the powder metallurgy and the are-cast types. Fabrication History of Bar Stock For this work, bar stock was procured from Climax Molybdenum Co. (are-cast type) and from Westing-house Electric Corp. (powder metallurgy type). The processing histories of these materials are listed in Table I. The first lot of are-cast molybdenum was deoxidized by aluminum additions. The second lot was deoxidized by carbon." Both lots of the powder Microstructure A microscopic examination of these materials, as received, revealed the powder metallurgy molybdenum to be free of inclusions and to be finely fibered. On the other hand, the are-cast C molybdenum possessed numerous carbide inclusions, and the arc-cast A appeared to have coarse grained fibers. These are shown in Fig. 1. Owing to the large apparent difference in fineness of fiber between the are-cast A and the powder product and are-cast C, a check was made of the recrystallized grain sizes to determine whether these differences persisted. A series of recrystallization anneals revealed mixed grain sizes in both the are-cast A and the powder product. Variations in grain diameter of as much as 50 times were found after full recrystallization at 1200°C for 30 min. There was no distinction between the two. Arc-cast C was not checked. Room Temperature Mechanical Properties Prior to subjecting the materials to fatigue tests, room temperature mechanical properties were determined. These data, together with the tensil: strength of the notched bars, data,togetherare listed in Table tensil: There were no significant differences in the tensile strengths of the two types of molybdenum. However, the powder metallurgy material was generally more ductile and yielded at a somewhat lower stress than the arc-cast material. Tensile strengths of the notched specimens indicated a slightly greater notch strengthening effect in the are-cast C than in the powder product, lot 2. Room Temperature Fatigue Properties Sample Preparation: Specimens were prepared for use in R. R. Moore rotating beam fatigue machines. These specimens had a continuous radius test section with a minimum diameter of 0.260 in. The specimens were prepared by grinding to shape and polishing to produce a smooth unworked surface. Polishing consisted of rotating a disk in the continuous radius section on which were attached, successively, emery belts of 240, 400, and 600 grit. The specimens were slowly rotated during the operation. The belt speed was high, and rotation was such that polishing scratches were longitudinal. Unnotched Fatigue Properties: Unnotched fatigue data were obtained from a number of specimens of each of the four lots of molybdenum. The results of the tests are presented in Fig. 2. From this figure,

Jan 1, 1956

By E. I. Alessandrini, A. U. Seybolt

Selective oxidation (preferential oxidation of a single alloy component) can be an important oxidation mode in the case of alloys such as Si-Fe, Al-Fe, and so on, when heat-treating in atmospheres of low oxygen potential. It was the purpose of this work to identify the oxide films formed on iron containing 31/4 pct Si at low oxygen potentials, and to make some observations on the H2O/H2 ratios required to form them. EXPERIMENTAL METHOD HYDROGEN of varying water content offers a very convenient method of establishing a wide range of oxidizing power, or oxygen potential. The method chosen to provide a desired H2O/H2 ratio was to nearly saturate hydrogen at room temperature by bubbling the gas through water at room temperature, and then to wring out the excess water by passing the wet gas through a long glass spiral immersed in a refrigerated liquid at a desired dew point. After oxidation, the samples were examined by electron diffraction in order to identify any film which might be present. PREPARATION AND TREATMENT OF SAMPLES The samples were prepared from a Si-Fe alloy made in the laboratory using electrolytic iron and 96 pct ferro-silico11, vacuum-induction melted, hot-rolled then cold-rolled to 0.015-in. thickness. After the cold-rolling the samples were annealed at 1000°C. Transmission Laue X-ray patterns showed very little evidence of preferred orientation, but it is likely that a weak texture could have escaped notice. The chemical analysis was as follows: 3.34 Si, 0.01 Al, 0.001 0, 0.006 C, 0.002 N. Before each sample was oxidized, it was polished through 4/0 emery paper, cleaned and dried using benzene, carbon tetrachloride, acetone, absolute alcohol, and ether. The method of oxidizing the samples was as follows: Samples about 1/2 by 1 by 0.015 in. were held in the upper, cool part of a vertical vacuum furnace until the desired temperature was established in the furnace, Fig. 1. The sample was then lowered into the uniform hot zone where it was heated quickly to the desired temperature, and subjected to hydrogen of controlled moisture content (dew point) as mentioned previously. Temperatures from 400" to 1000°C were used, and dew points from room temperature to —78°C were explored. In general, the runs lasted about 6 hr, but a few runs were of different duration, as will be indicated later. After the predetermined period of time had elapsed, the specimens were withdrawn by the hollow stainless steel-quartz holder to a cool zone at the top of the furnace. EXPERIMENTAL RESULTS The results are summarized in Table I. Most of the electron-diffraction patterns were obtained by glancing-angle reflection, but in a few cases it was possible to strip the oxide films from the surface by a total immersion in a 3 pct bromine-methanol solution. Some of the thinner stripped films yielded quite satisfactory transmission patterns. However, both diffraction techniques yielded the same results; the patterns while most frequently showing a (low) tridymite, also showed a (low) cristobalite in some cases. A few patterns showed evidence of both phases. Because of the known nonequilibrium behavior of silica, it is not surprising that both forms of silica could coexist on one sample. It was noted that at fairly low dew points such as —40°C, there was a tendency for diffuse diffraction rings, suggesting a very small crystallite size. Also some subsequent experiments to be reported later show that thin silica films can be amorphous.

Jan 1, 1959

By Reinhardt Thiessen

In the general study of coal, all evidence points in the one direction —that coals had their origin in a manner analogous to that of peat. The best method of studying coal, whether it concerns its chemistry, composition, or physical condition, is to study peat. The essentials in a study of peat are a knowledge of the chemistry of plants, knowledge of decay and of the transformation process of plant-substances into peat. A number of facts must be emphasized, namely, (1) peat is formed under wet conditions only; (2) plants grow in the place where peat is formed; (3) all the plant substances go into the bog; and (4) all the plant substances are subjected to a series of phases of decay which are (a) in the air completely above the water level but in relatively moist conditions; (b) above the water level, but covered by debris; and (c) completely submerged by both water and debris. Plant Chemistry Plant chemistry as a whole is remarkably well understood. The number of compounds composing plants is large, and it is not possible here to give even a comprehensive outline, but a classification into definite groups is possible; this is as follows: Carbohydrates; glucosides; pigments; tannins; acids, alcohols and ketones, etc., and their salts; essential oils; resins; vegetable bases; proteins; enzymes. Plant substances may also be grouped according to the role they play in the life of the plant, such as: Framework materials, living materials, food materials, protecting materials, waste materials. While this classification groups them well for. certain purposes, it does not group them exactly chemically; but in a consideration of the composition of coal, this is an excellent classification for our purpose here.

Jan 1, 1925

By Phillip B. Bucky, R. S. Taborelli

The term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater inechanization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar inodel built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimenbions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein. Longwall Mining What Is Longwall Mining?—Agreement should be reached as to what constitutes longwall mining and therefore what constitutes a longwall face. Let longwall mining be defined as the mining procedure in which the roof and overlying bed breaks tend to parallel the working face. In the ordinary stope or room-and-pillar mining the roof breaks tend to

Jan 1, 1938

By Phillip B. Bucky, R. S. Taborelli

The term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater inechanization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar inodel built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimenbions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein. Longwall Mining What Is Longwall Mining?—Agreement should be reached as to what constitutes longwall mining and therefore what constitutes a longwall face. Let longwall mining be defined as the mining procedure in which the roof and overlying bed breaks tend to parallel the working face. In the ordinary stope or room-and-pillar mining the roof breaks tend to

Jan 1, 1938

By K. M. Rolls, R. M. Rose, H. B. Shukovsky

Studies of the phase structure, critical current density, and resistive critical magnetic field of a 45 pct Nb-55 pct Zr superconducting alloy after final-size heat treatments are reported in this paper. A combination of optical metallography, X-ray diffraction, and electrical-resistivity measurements were used to determine the phase structure. Superconductivity measurements, made with heat-treated wires, are correlated with microstructure. Although no quantitative relationship between microstructure and critical current density is found, it is shown that SINCE Kunzler1 as well as Berlincourt, Hake, and Leslie2 first described the high-field, high-current-density superconductivity of Nb-Zr alloys, it has be- the critical current density is highest when the microstructure is finely divided by fibering, coring, precipitation, or fine-scale phase dispersions. The resistive critical field is very sensitive to the compositions of the phases present. Since the alloy investigated here is near the maximum resistive critical field for the Nb-Zr system, any phase decomposition results in a lower H,. Elimination of the effects of cold work lowers H, also. A possible interpretation of the latter in terms of internal surface superconductivity is suggested. come apparent that the resistive critical field and the current-carrying capacity of such alloys are, in large measure, dependent on composition and processing. The resistive critical magnetic field (Hr) for low current densities has been found to increase progressively with zirconium content until a flat maximum is reached between 50 and 65 pet Zr.3 For any single composition, a characteristic maximum value of H, is attained by heavily cold-drawn wire.4 critical current density (J,) depends not only upon cold work but also, apparently, upon microstructure. Heat treatments of cold-worked wires generally

Jan 1, 1965

By J. E. Johnson

It is the purpose of the present paper, while not excluding chemical considerations, to deal more extensively with some of the physical and mechanical aspects of the blast-furnace process, and to point out its dependence, in these respects, on well-known laws. The quantity and cost of ore and flux required to make a ton of iron being determined by circumstances over which the furnace-man, under given conditions as to quality and quantity of product, has commonly little control, the principal item of cost, apart from the saving of labor, which he can aspire to reduce, is that of fuel. To determine the limits of possibility in this direction is clearly the first step in a practical inquiry; and this step is represented herewith in Fig. 1, a diagram showing the total useful effect obtained from a pound of fuel under various conditions, and thus permitting direct comparison, under any given conditions, between actual results and the maximum possible results. The following statements will explain the basis upon which this diagram has been constructed. One pound of fuel, containing 90 per cent. of fixed carbon (which represents average conditions), is taken as the unit. The degree of oxidation of the carbon is measured by the ratio of the two oxides of carbon contained in the top-gases. It is necessary to remember that a considerable quantity of carbon is brought in as carbon dioxide by the flux, and to take account of it and of its condition. It is here considered that the carbon dioxide liberated by the limestone does not affect the analysis of the top-gases, and that the ratio of CO to CO2 will remain unchanged by the addition of limestone; enough CO, being reduced by the solution

Jan 1, 1906

By W. H. Schacht

IN THE Lake Superior District, the air indoors must be heated continuously during eight months of the year and occasionally during the remaining months. Incident with mining in this district, therefore, there is need for heating many of the buildings connected with these operations. In addition to the mine buildings, that is, shops, engine, houses, offices, change houses, etc., such public buildings as schools, library, and theater, when close to the mines, are often supplied from the mine heating mains. At the Copper Range Company's mines, Champion, Trimountain and Baltic, the heating surface thus supplied from the mine mains is over 50,000 sq. ft. (4645 sq. m.) which requires a steam consumption, at times, of 18,000 lb. (8165 kg.) per hour, or the equivalent of a rate of over 50 tons of coal per day (were live steam used). This figure is based on a consumption of 1/3 lb. per square foot of heating surface during the coldest weather, and provided the system is not wasting steam by blowing it to the atmosphere or into the return line on account of leaky traps, which so often is the case. Under the latter conditions, steam consumptions of three to four times the above rate are not uncommon. This shows that the cost of heating is of enough importance to be given serious consideration, especially at this time of rising prices of fuel. The power and heating value of exhaust steam are appreciated by most engineers, and its application for such purposes is general. At our stamp mills, the exhaust from the stamps is used to operate low-pressure turbines, thus reducing the former water rate per horsepower developed by more than 50 per cent.

Jan 8, 1920

By C. C. Singleterry, D. L. Katz

The critical phenomena have been studied during the past century but our knowledge of the critical temperatures and pressures of complex hydrocarbon mixtures still is very limited. The critical temperatures and pressures of pure substances have been examined in large numbers120 and in great detail.11.17 No experimental determinations of the critical phenomena have been reported on such complex hydrocarbon systems as a reservoir fluid. The critical temperature is defined by Taylor18 as follows: "there is some temperature for each gas above which the gas cannot be liquefied. This temperature is called the critical temperature." The critical pressure of a pure substance is the vapor pressure at the critical temperature. It should be noted that these definitions refer to a given substance in the pure state and do not mean that the pure substance cannot be liquefied in the presence of a second constituent. The normal procedure for obtaining the critical temperature of a substance is to heat it in a glass tube 1,20 under pressure until the meniscus between the liquid and vapor phase disappears, although other methods, especially for mixtures, have been used.13,14 However, when considering oil and gas reservoirs, it is more enlightening to consider a critical phenomenon that occurs when a mixture of oil and gas are compressed at a reservoir temperature until the meniscus disappears because the two phases become equal in composition. This conception, along with erroneous applications of the definition of the critical phenomena of a pure substance to that pure substance when it is part of a complex mixture, has caused confusion even among persons familiar with the classical theories. The purpose of this paper is to discuss the critical phenomena of pure substances and mixtures and to report experimental data on a mixture of

Jan 1, 1939

By C. C. Singleterry, D. L. Katz

The critical phenomena have been studied during the past century but our knowledge of the critical temperatures and pressures of complex hydrocarbon mixtures still is very limited. The critical temperatures and pressures of pure substances have been examined in large numbers120 and in great detail.11.17 No experimental determinations of the critical phenomena have been reported on such complex hydrocarbon systems as a reservoir fluid. The critical temperature is defined by Taylor18 as follows: "there is some temperature for each gas above which the gas cannot be liquefied. This temperature is called the critical temperature." The critical pressure of a pure substance is the vapor pressure at the critical temperature. It should be noted that these definitions refer to a given substance in the pure state and do not mean that the pure substance cannot be liquefied in the presence of a second constituent. The normal procedure for obtaining the critical temperature of a substance is to heat it in a glass tube 1,20 under pressure until the meniscus between the liquid and vapor phase disappears, although other methods, especially for mixtures, have been used.13,14 However, when considering oil and gas reservoirs, it is more enlightening to consider a critical phenomenon that occurs when a mixture of oil and gas are compressed at a reservoir temperature until the meniscus disappears because the two phases become equal in composition. This conception, along with erroneous applications of the definition of the critical phenomena of a pure substance to that pure substance when it is part of a complex mixture, has caused confusion even among persons familiar with the classical theories. The purpose of this paper is to discuss the critical phenomena of pure substances and mixtures and to report experimental data on a mixture of

Jan 1, 1939

Discussion of the paper of N. V. Hansell, presented at the Cleveland Meeting, October, 1912, and published in Bulletin No. 72, December, 1912, pp. 1497 to 1,517. C. Q. PAYNE, New York (communication to the Secretary*) :-Mr. Hansell has presented in his paper a very interesting and valuable summary of the various methods of enriching iron-ores which have been developed during recent years. Particularly striking in this connection is the high degree of enrichment of the concentrates from magnetic iron-ores which is now commercially feasible. Magnetic concentrates containing from 6 7 to 139 per cent. of metallic iron, showing an efficiency of 90 and even 95 per cent. in. their separation, are not now uncommon. Such results exceed those obtained by gravity methods of treatment of all copper-, lead-, and zinc-ores, and are only equaled in the cyaniding of gold-ores and in the flotation treatment of certain copper-ores. It is of interest to note that the-type of magnetic field which is employed in securing these results, in the Gröndal (wet) and the Ball & Norton (dry) systems of treatment is the same in each case : viz., a field of alternating north and south poles. The credit for developing this simple and useful field, which has found so wide an application both in this country and abroad, is due to two American inventors and engineers, Clinton M. Ball and Sheldon Norton. At the same time, it should be noted that part of the improvement in the grade of the magnetic concentrates, especially in the case of the wet treatment of finely mineralized ores, is due to a well-devised scheme of mill-treatment, whereby a rough concentrate is usually obtained as an intermediate product, which is then recrushed and reseparated in obtaining final clean products.

Jan 3, 1913

By J. C. Humbert, J. F. Elliott

The solubility of nitrogen in liquid pure Fe, Cr, and Ni, in liquid Fe-Ni, Fe-Cr, and Ni-Cr alloys and Fe-Cr-Ni alloys, has been measured by the Sieverts' type apparatus between 1500° and 1800°C. Tabulations and graphs of the solubility data and activity coefficients are shown. Heats of solution are reported. Interaction coefficients of the several elements in Fe. Cr, and Ni ave also reported. THE solubility of a gas in a liquid metal is usually measured by either the quenching technique or the so-called Sieverts' method. In the quenching method, 1-3 the melt is equilibrated at the desired temperature and pressure with the gas phase having a known fugacity of the gas being studied. The melt is sampled and the sample is quenched and analyzed chemically for its gas content. In Sieverts' method the melt is contained in a closed chamber. The apparent volume of this chamber, i.e. the "hot volume," is usually determined by introducing a known quantity of an inert gas having very closely the same physical characteristics as does the experimental gas. Alternatively, the experimental gas is used with an inert specimen having the same general physical characteristics as does the experimental melt. Subsequently, the experimental melt is equilibrated with the experimental gas by introducing a known quantity of the gas into the calibrated chamber. The solubility of the gas is obtained from P-V-T relationships. The quenching method suffers from' the limitation that some gas may be gained (as in the case of Cr-Fe alloys) or lost (as in the case of Fe-Ni alloys) during solidification and cooling of the sample. With Sieverts' method sampling and analysis are unnecessary. However, errors can result from the difficulty of determining accurately the "hot volume,"

Jan 1, 1961

By R. V. Whetsel, V. R. Gargias, J. W. Ristori

WoRld consumption of petroleum and its substitutes in 1941, the amount of which obviously is largely conjectural, is estimated at 2,066,653,000 bbl. This is 48,689,000 bbl. more than the previous year and is an all-time high. Except for the United States, this figure does not include consumption for military purposes. Consumption in the United States also reached an all-time high during 1941, totaling 1,492,000,000 bbl., or 158,230,000 bbl. more than the previous peak year of 1940. On the other hand, it is estimated that civil consumption in countries outside of the United States decreased 109,541,ooo bbl. as compared with the previous year. Demand for military purposes and/or additions to stocks in countries outside of the United States is estimated at 304,507,000 bbl. during 1941, compared with 209,635,000 bbl. in 1940. This increase was due largely to blitzkrieg warfare on several fronts. especially Russia; entailing large expenditures of petroleum by both sides because of the immense area covered by the fighting forces, the long supply lines necessary and the intensity of the fighting. It is interesting to note in this connection that Axis-controlled countries, excluding Japan, had an estimated production of approximately 89,000,000 bbl. of petroleum and its substitutes in 1941. The peacetime consumption of these countries in 1938, for example, was about 183,000,000 bbl. It is believed that the minimum to which civil consumption could possibly be re-duced in wartime is 20 per cent of that of peacetime, which would call for a minimum consumption of 37,000,000 bbl. in these countries in 1941 for civil purposes. This

Jan 1, 1942