Search Documents

By J. E. Elliott, K. O. Miller

Solubility studies were carried out to establish the phase distributions for various Fe-Ni-Pb-C alloys at temperatures where the metallic components exist as liquid solutions. Temperature us composition diagrams for the Ni-Pb, Fe-Pb, Fe-Ni-Pb, and Ni-Pb-C systems are derived by employing various approximations in conjunction with the data. Results are summarized for 1550°C in a quaternary phase diagram of the Fe-Ni-Pb-C system. BECAUSE surprisingly little information has been published on the phase diagrams of the Ni-Pb, Fe-Pb, Fe-Pb-Ni, and Fe-Ni-Pb-C systems, a study of these systems was undertaken to ascertain the important phase relationships in the temperature range of 1300" to 1550°C. Measurements were also made on the carbon-saturated systems in the hope that they would assist in the interpretation of the systems without carbon. This paper reports the results obtained from the simple equilibration of the various liquid and solid phases. EXPERIMENTAL PROCEDURE The experimental technique involved holding appropriati quantities of the metals in an alumina crucible, or in a graphite crucible when saturation of the melt with carbon was desired, for sufficient time at the desired temperature to ensure equilibrium. Then a sample of each liquid phase presen was drawn into a small-bore silica tube. This sample was withdrawn quickly from the furnace, cooled, and sent to the chemical laboratory for analysis. The cell assembly used is shown in Fig. 1. Durin the work on the Fe-Pb-Ni system, it was placed in a furnace wound with 20 pct Rh-80 pct Pt wire. This furnace eventually failed and subsequent studies were carried out between 1350" and 1475°C in a tube furnace heated by silicon-carbide resistance elements. A protective atmosphere of argon with approximately 10 pct hydrogen was supplied to the cell assembly at a gage pressure of 1 in. of water. Hydrogen was passed over palladized alumina and then anhydrous calcium chloride for purification. Argon was purified of oxygen and water vapor by passing it over copper gauze at 550°C and then through a calcium chloride drying column. The gases were mixed and redried before they entered the equilibration cell. Temperature was measured by calibrated Pt/Pt-10 pct Rh thermocouples and a Rubicon Type B potentiometer. The thermocouples were standardized against the melting points of pure nickel

Jan 1, 1961

By Nicholas J. Grant, Klaus M. Zwilsky

EVER since the unusual high temperature creep resistance and structure stability of SAP (Sintered Aluminum Powder) and similar aluminum-alumina alloys were reported,'," there has been a need to determine whether other metal-metal oxide (or other hard stable particle) alloys, not so ideal as the Al-Al 2 O 3 system, would show similar high temperature strength and stability. Of the many possible methods of obtaining a metal-metal oxide alloy,a one that offers many practical and theoretical advantages is the simple mechanical blending of metal powders with hard stable particles, followed by pressing, sintering, and hot extruding. With this purpose in mind copper powder and silica and alumina were selected for experimentation because these materials are readily available, cheap, reliable, and lend themseives te the simplest processing and testing. Starting Materials—Two sizes of electrolytically deposited copper powders were used, a —200 mesh powder referred to as A powder in this investigation and a —325 mesh powder referred to as C powder. Silica was added in the form of pure Potter's flint from which a —10µ fraction had been separated. Alumina of the a variety was used in two size ranges. The first was a —10µ fraction separated from a coarser aggregate, the second a commercial product of 0.3µ average diam manufactured by Linde Air Products. Preparation of Powders—Five-hundred gram batches of A copper with 1, 3, and 10 volume pct of each of the three oxides mentioned above were prepared, as well as C copper containing 1, 3, and 10 volume pct of —lop silica. Powders were weighed out carefully and blended by ball milling in air for 24 hr. Since this treatment resulted in surface oxidation of the copper, the charge was hydrogen reduced at 260°C for 5 hr. The next step consisted of hydrostatically compacting the powder into a shape suitable for the required hot working. For this purpose a slug about 11/2 in. in diam and 31/2 in. in length was produced by placing the mixed powders into a rubber sleeve, holding in a perforated steel canister, and rubber stoppering at the ends; the assembly was then subjected to a hydrostatic pressure of 50,000 psi. The air was evacuated from the assembly prior to pressing in order to prevent

Jan 1, 1958

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1-4 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio,' in the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably those from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1952

By W. R. Hamilton

The knowledge of the existence of petroleum in Southern California dates back to the days of the missions. The presence of asphaltum and semisolid bitumen was reported at Santa Barbara in 1792, but no serious attempt was made to develop oil until Professor Silliman's optimistic report in 1865 started California's first oil boom. Wells were drilled in many counties of the State, but the equipment was unsuitable and the drilling difficult and no production was obtained except in Ventura County. Even there the production was of little importance commercially, and not until the early '80s did it become sufficient to again attract attention. In 1888 the production for the State had reached a total of about 700,000 bbl. per year, practically all light oil produced in Ventura County, Pico Canyon, Los Angeles County and in the Puente Hills. The production of petroleum attained the dignity of an industry in 1895 when the Los Angeles City and Coalinga fields were discovered. The subsequent development has been remarkable, and in 20 years the production has increased from 1,000,000 to 100,000,000 bb1. per year. The refining industry has kept pace with the production of oil. The Pacific Coast Oil Co., the predecessor of the Standard Oil Co. of California, was the virtual pioneer refining company of the State, having built a refinery at Alameda about 1880. When purchased by the Standard, about 1902, it was dismantled and the refinery at Point Richmond was built. The Richmond refinery is now one of the largest in the world, having a capacity in excess of 60,000 bbl. per day. A small refinery was built by the Union Oil Co. at Santa Paula in the early days of the industry and later many asphalt refineries were in operation in Southern California. The Pacific Coast Oil Co. was then, as has been its successor, the Standard Oil Co. of California, the principal refiner and marketer of light products, the most valuable of which was kerosene. Before the opening of the twentieth century, gasoline of excellent quality was produced, though it was always a drug on the market and was produced for the simple reason that its presence rendered the flash and fire tests of the kerosene too low. The user of kerosene at the present

Jan 1, 1917

By F. S. Buffington, Morris Cohen

THERE is little quantitative information available concerning the effect of applied stress, in both the elastic and plastic ranges, on diffusion kinetics. Accordingly, a program has been undertaken to determine the rate of self-diffusion in high purity iron, with the specimens subjected to stress during the course of diffusion. Results are reported here for body-centered cubic iron at a diffusion temperature of 890°C. The iron used was 99.97 pct Fe, the principal impurities being 0.002 pct C, 0.008 pct 0, and 0.02 pct Si. The surface-decrease method of self-diffusion analysis was employed, and Fe55 Mn x-radiation, 2.9 years half-life) was the tracer element. Details of specimen preparation and equipment are given elsewhere.' Disks of the high purity iron, % in. diam x 1/4 in. thick, were annealed at 890°C for 18 hr in dry hydrogen to produce large grains of a ferrite. The faces of the disks were then surface ground, and possible grinding stresses were relieved by annealing at 890 °C for 45 min in vacuum. A layer of radioactive iron 0.00186 cm thick was electroplated on one face of each disk. The self-diffusion coefficient was calculated from the ratio of the radiation intensities emanating from each of these faces, as measured before and after diffusion.' The heating was carried out in a vacuum furnace (10-5 mm Hg) controlled to ±1.5°C. The specimens were loaded in compression between two quartz disks during the diffusion runs by means of a lever system operating through a vacuum seal. Thus one quartz disk was pressed directly against the radioactive face of the specimen, minimizing the vapor loss of radioactive iron. Steady-state creep occurred in all instances where permanent deformation could be detected, but the specimens did not exhibit appreciable transverse barreling until natural strains of 0.2 to 0.3 were attained. Essentially, the diffusion took place under uniaxial stress. The plastic strain in each case was obtained at the diffusion zone by measuring the diameter d there before and after the run: e = 2 In — do Let Du equal the self-diffusion coefficient which would have prevailed at the given temperature if no stress had been applied. This was calculated from the temperature-dependence equation which had been previously determined: —59,800 D, = 6.2 exp ( I sq cm per sec* [I]

Jan 1, 1953

By H. J. Engell, W. Frank, A. Seeger

SWISHER and ~urkdogan' have determined the solubility of oxygen in a iron. They found it to lie between 7 and 10.5 at.-ppm at 881°C. Using earlier work on the permeability of oxygen in bcc iron,' they arrived at the following expression for the diffusion coefficient of oxygen in bcc iron (k = Boltzmann's constant, T = absolute temperature): where The present authors3 have estimated the activation energy QD for the diffusion of oxygen in bcc iron in two different ways from various experimental data.2'4"6 In the first method QD + QS (QS = heat of solution for oxygen in bcc iron in thermodynamic equilibrium with solid FeO) was determined either from data on the reduction of FeO with hydrogen4 or from measurements of the internal oxidation of silicon in a iron.5 Using an estimate of QS from investigations of the oxygen solubility in 6 iron2 (in thermodynamic equilibrium with molten FeO) Q = 0.97 ev or Q~ = 1.06 ev were obtained. From the magnitude of these values it was concluded that oxygen migrates interstitially in bcc iron and that consequently the activation energy QD for diffusion of oxygen has to be identified with the migration energy E~ of the oxygen atoms. Therefore, for a second estimate of QD from the diffusion coefficient of oxygen in 6 iron at 1450" ~,~ we used the theoretical expression:3 (a = length of elementary cube edge, m = mass of interstitially diffusing atom, sM = migration entropy), applicable to diffusion via the octahedral interstices in bcc lattices. Taking sM = 3.8 k (migration entropy of carbon in a iron), one gets Q = 0.90 ev. Hence, in Ref. 3 Q = (0.98 *0.1) ev was proposed as a plausible value for the diffusion energy of oxygen in bcc iron. sM + 9 (9 = solution entropy for oxygen in bcc iron) can be determined from permeability measurements.4 Using the above-mentioned estimate for QS , the following expression for the solubility c (atomic concentration) of oxygen (in thermodynamic equilibrium with solid FeO) in bcc iron was derived: From [4] the solubility of oxygen at 881°C in a iron is calculated to lie between 0.6 and 12 at.-ppm. We see that the solubility determined by Swisher and

Jan 1, 1969

By Lawrence Addicks

Some three years ago the smelter connected with the Chrome, N. J., refinery of the United States Metals Refining Co. found itself embarrassed by constantly increasing piles of unsmelted blast-furnace flue dust. The charge was fine and 10 to 15 per cent. of it was blown over into the flue. Sulphur was at that time too scarce to make the sintering of the finer part of the charge attractive, and raw-ore smelting in a reverberatory with a partly oxidized charge was not to be thought of. A great many schemes were considered, including leaching, blowing into the converters, and briquetting, the problem finally narrowing down to blast roasting and nodulizing. It was found by experiment that blast roasting would not yield a satisfactory sinter without the addition of coke dust or sulphide fines to augment the fuel value of the flue dust, and on this account, together with the low first cost of a kiln, the latter was decided upon. A couple of tons of flue dust were tried out in the experimental kiln in the laboratory at Yorktown, Va., of J. H. Payne, who acted as consulting engineer in this connection. This kiln was approximately 2 ft. in diameter and 20 ft. long and was fired with fuel oil. A run of several hours yielded excellent nodules. The ki1n showed no tendency to build in and form "nose rings" and gave a fuel consumption of 50 gal, of oil per ton of flue dust. There was no indication of any stack loss. The roasting was strongly oxidizing. A study of what full-size kilns were doing on cement clinker and on nodulizing pyrites cinder indicated that a 60 by 6 ft. kiln would certainly not consume over half of the oil per ton of flue dust shown on the test and as fuel oil at that time was selling around 2 1/2 c. per gallon it was decided to let it go at that. A 60 by 6 ft. kiln was decided on, as that size is standard in cement practice, although fast being replaced by much larger ones with their greater fuel economy, and as it fitted in the building space available. A 6-in. brick lining brought the net diameter down to 5 ft. The inclination

Jan 1, 1915

The world's production of petroleum in 1926 amounted to nearly 150 million long tons, of which India contributed 0.72 per cent. In 1927, this figure jumped to some 172 million long tons, of which the Indian proportion, on a practically stationary production, fell to 0.64 per cent. In 1928, there was another substantial rise in the world's production, which reached the figure of over 181 million tons. In 1929, there was another jump to over 202 million tons, but in 1930 the world's production fell to about 193% million tons, in 1931 to about 187 million tons, and in 1932 to about 183 million tons, while in 1933 the production rose again to about 202 million tons, in 1934 to about 215 million tons, and in 1935 to 233 million tons1. Decreases were shown by Poland, Sarawak, Egypt, Rumania and France. All other important producers showed an increase in production, by far the largest being due to Iraq, as a result of the opening of the pipe line to the Mediterranean. The United States contributed 60.9 per cent of the world's supply in 1935, Russia 10.7 per cent, Venezuela 9.4 per cent, Rumania 3.9 per cent and Iran 3.1 per cent. In 1928, India contributed 0.64 per cent, which fell to 0.60 per cent in 1929 and rose to 0.62 per cent in 1930, 0.63 per cent in 1931, and 0.64 per cent in 1932, and fell again to 0.62 per cent in 1933, to 0.60 per cent in 1934 and to 0.50 per cent in 1935; her position on the list of petroleum-producing countries fell from eleventh in 1929 to twelfth in 1930 to 1933, her place being taken by Trinidad and to thirteenth in 1934 and 1935, owing to the production by Iraq. The production of petroleum in India (including Burma2) increased slightly from 322,025,280 gal.3 in 1934 to 322,662,336 gal. in 1935, the highest figure in the history of the industry. The increase in 1935 is due to an increase of some 4 million gallons in Assam, almost offset by a decrease of 31/2 million gallons in Burma. This increase in output in 1935 was accompanied by an increase in estimated value amounting to Rs. 22,73,550 (£170,944).

Jan 1, 1937

By C. Edwin Nighman

THE following is a description of the methods used in rescuing men and extinguishing the underground fire at the Pennsylvania mine, Butte, Mont. This fire, which cost the lives of 21 men, began about 9 p.m., Feb. 14, 1916, at or near a ventilating fan on the 1,200 air-shaft station. This shaft at that time was downcast, while the main hoisting shaft was upcast. Owing to the proximity of the fire to the air shaft, the air in the latter soon became heated, and as the fan on the level was not running¬the power having been cut off shortly after the outbreak' of the fire-the aim' shaft became upcast to the 300 level. At this point a blanket of cold air from the surface caused the smoke and gases to he drawn in on that level and carried down again through the workings to the 1,200. A short time after the discovery of the fire, water was turned down the air shaft through a series of pipes around the collar of the shaft, which caused the smoke to recede, below the 300, so that within 2 hr. it was possible to search that level for the missing men. From the above it will be apparent why the air shaft was upcast instead of downcast as under normal conditions, and why men were suffocated at considerable distances from the seat of the fire. The smoke and gases that came up the main hoisting shaft did not diffuse through the workings to any extent. There are doors on all levels in the connections to the main hoisting and air shafts, but-in the confusion and running around many of these doors were left open, and this undoubtedly caused the smoke and gases to spread more rapidly than they would otherwise have done. It was necessary for most of the men on the various levels to pass close to the air shaft in going to the hoisting shaft, and when they encountered the smoke and gases in that vicinity a number turned hack and climbed down with the direction of the air currents and were then suffocated, while all those who passed through the relatively short pall of smoke to the main shaft were saved.

Jan 2, 1917

H. H. Hill.—I believe that as petroleum engineers you are all more or less interested in geophysical prospecting. A large number of the papers that have been written on that subject are too detailed or too much involved to be of much value to a person who is not familiar with the subject, so I suggested to Mr. Fohs that he might bring us something that we could all understand. As I take it, we are interested in learning something about the different methods, the places where they have been used, their limitations and in general whether they have given satisfaction in locating oil deposits. F. J. Fohs, New York, N. Y.—I will briefly summarize some of the results as I Bee them from my practical contacts with them and my discussion of the subject with some of the more important rnen both in this country and Europe. Geophysical Methods 1. Seismographs: A. 1. Sonic refracting seismographs of Karcher, McCullom and Reiber. For rapid reconnaissance and also for detail—perhaps, the best type of instrument. 2. Mechanical refracting seismographs of the Weichert-Mintrop type. B. I. Sonic seismographs using reflected sound from contacts of sufficiently unlike beds where latter are thick enough, being used for detail of both salt domes and ordinary structures where a good reflecting key bed occurs. 2. Torsion Balances: Made in three sizes with greater portability and loss of but 20 per cent. in medium size and loss of 40 per cent. efficiency in smallest size. A. Used to best advantage in detailing salt domes, in noting anomalies of deep-seated structures of the Edgerly, La., type (but not always certain here and dependent on interpretation which involves both experience and the human equation to a large degree). R. Used to advantage in mapping faults where a lime or other denser bed occurs upthrown, and the topographic irregularities are not too involved. C. Of use where buried granite plugs and buried-hill structures occur as in the Western Texas fields. D. Believed of little use for other types of structure. 3. Magnetometers or Variometers: Now built horizontal and vertical with declinometer combined in one instrument. A. Practical in mapping granite or basic igneous rock plugs and intrusions, or of detritus therefrom. Adams has recently demonstrated definite results in mapping the well known Panhandle arch.

Jan 1, 1928

C. E. Dewey, Georgetown, Colo. (communication to the Secretary) : In his remarks on crushing-machinery, Mr. Douglas says (Twins., xxii., p. 322): "To insure a smaller and more uniform size of particles in the crushed material, the Dodge crusher still communicates motion to the upper extremity of tile movable jaw, which oscillates on fixed pivots projecting from its lower extremity!' The notion that, in order to obtain a fine and uniform product from a rock-breaker, the movable jaw must be pivoted at its lower extremity, seems to obtain generally among mill-men, as well as among manufacturers of machinery. My experience with machines of both types does not confirm this belief. It is true that, to obtain a uniformly fine product from a jaw-crusher, the stroke at the lower extremity of the crushing-surface must be short; but that the movement at that end must be less than at the other or receiving-end is, I think, an erroneous assumption. Figs. 1 and 2 are intended to illustrate the two types of machine. It is found in practice that the capacity and the nature of the product of either machine, as usually constructed, are governed by the opening, C D, and the length of stroke of the movable jaw at D. This being the case, machines of either type, of the same width of crushing-surface, running at the same speed, and having the same adjustment as to opening and stroke at D, should give, when fed

Jan 1, 1895

By Graham John Mitchell

In May, 1919, a crosscut on the 1400-ft. level of the Briggs mine, a Calumet, & Arizona property at Bisbee, Ariz., penetrated a deposit of pyrite and chaleopyrite that had replaced quartzite and limestone and was cut, especially in the quartzite, by numerous fractures. As the drift advanced through these fractured portions, they were found to be free from copper-sulfate minerals although '(sooty" chalcocite was present in the fractures and also as coatings and replacements of pyritc. Howcver, sulfate soon made its appearance in certain fractures, filled them, and began to form stalactites. Several centers of incipient growth were noted for subsequent study, observations in the drift at frequent intervals during the past 17 months affording the opportunity of determining the rate of formation of the stalactites. The one to attain the greatest growth during the period of observation measured 27 in. long and averaged 1 in. in diameter. A close study showed it to be composed of small interlocked crystals of chalcanthite radiating from a small central tube-like opening. The trielinic form of the crystals was evident with prism and pinacoid faces recognixable. Assuming that the supply of copper-sulfate solution was constant (luring the 17 months—-and such an assumption is supported by the fact that the number of drops of excess solution falling, per minute, from the tip of the stalactite at the times of observation checked closely—thc stalactite, it has been estimated, grew at the rate of 1.58+ in. per month. DISCUSSION James I?. Kemp," New Yolk City.—J. S. Curtiss, in the monogr:tpll on Eureka, Ncv., say:: that a stalactite formed in limestonc grew 5/8 in. in three weeks and continued to grow as long as it had a drop of water or solution at the lower end. Another grew at the rate of 3/8 in. in the same time. In the case cited by Mr. Mitchell, the growth was about 136 in. in three weeks. A year ago we had an instance of the formation of cubes of galena on a railroad spike. A mine in northeastern Oklahoma had been idle about two years but on account of pumping of neighboring properties, the circulation of water was active throughout the drift. A cube of galena,

Jan 1, 1922

By D. Mizer, J. B. Clark

In a recent investigation of the entire magnesium-yttrium phase diagram, Gibson and Carlsonl report the maximum solid solubility of yttrium in magnesium as 8.0 wt pct Y at 1050°F (565°C). However, independent studies of the precipitation in magnesium-yttrium alloys, 2 conducted prior to the publication of the above phase diagram, indicated a greater solid solubility of yttrium in magnesium. Accordingly, the magnesium-rich region of the diagram was re-investigated to determine more accurately the liqui-dus, solidus, and solvus of the magnesium solid solution in this system. Metallography and thermal analysis were chosen as the best corroboratory methods for accurately determining this region of the diagram. A magnesium-yttrium master alloy was prepared from yttrium of 99.9 pct purity and singly sublimed magnesium of 99.9 pct purity. Subsequently, the twelve magnesium-yttrium alloys shown in Fig. 1 were prepared using standard alloying procedures for magnesium. Metallographic samples of the alloys were heat treated under an SO, atmosphere in an electric furnace capable of control within ±3oF of the desired temperature. Alloy samples for the metallographic determination of the solvus, and for the precipitation studies were solution treated at 1000° F for 16 hr. Subsequent aging times for the solvus determination varied from a minimum of 6 hr for the higher temperatures up to 816 hr for lower temperatures. Periods of 30 min at temperature were used to generate liquation for the metallographic placement of the solidus and eutectic horizontal. The liquidus and the eutectic horizontal were determined by thermal analysis. Simple time-temper- ature heating and cooling curves were obtained from 10-g alloy samples heated and cooled in a well-insulated electric furnace. An Iron-Constantan thermocouple was placed in direct contact with the sample. The thermocouple did not contaminate the alloy sample since metallographic examination showed that the alloy melt did not wet or attack the thermocouple. The heating and cooling rates were approximately 5 to 8OF per min. The standard metallographic procedures for magnesium were used in polishing and etching the magnesium-yttrium alloys studied. Glycol etchant* was etchant was used to reveal precipitate in the solvus determination. The redetermined magnesium-rich region of the magnesium-yttrium diagram is shown in Fig. 1. The

Jan 1, 1962

By Wm. Reuben Webster

Brass is an alloy of copper and zinc. The brass containing 70 per cent copper and brasses (using this term to denote all useful 30 per cent zinc. Fig. 3 shows the effect of proportions of the two constituents) are the annealing at various temperatures on the most valuable and widely employed of all same alloy. This effect is somewhat modi- nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity —the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time. at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a camparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Wm. Reuben Webster

Brass is an alloy of copper and zinc. The brass containing 70 per cent copper and brasses (using this term to denote all useful 30 per cent zinc. Fig. 3 shows the effect of proportions of the two constituents) are the annealing at various temperatures on the most valuable and widely employed of all same alloy. This effect is somewhat modi- nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity —the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time. at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a camparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi- [ ] fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By C. E. Shoenfelt

There were 110 important discoveries of either oil or gas in Co1orado in 1935. There was, however, further development of the Price structure in southern Colorado and developments since the first of the year indicate. that an important oil field may be in the making. The discovery of oil in Price structure was made by the Oil City Petroleum Co. late ill Novem-ber, 1934, in its No. 2 Garnett in the northeast corner of lot 3 in the SW.¼ of sec. 25-33N.-2E. This well developed a good showing of oil in Dakota sand at 970 ft. The hole filled up 15 ft. with 40° gravity oil overnight and after standing for several days the oil level was 400 ft. higher. As a result of the discovery of oil by the No. 2 Garnett, three wells were drilled by the William E. Hughes Estate. Two of these wells had good showings of oil and may make good producers but it is doubtful whether they will produce the estimated capacity of 500 bbl. each with which they have been credited. Although the Hughes Estate wells have been completed for some time, they have not been given thorough production tests because of the isolated position of the field and lack of proper facilities. The. first well drilled by the Hughes Estate was located on the west side of the Navajo River on the downthrow side of a fault. It encoun-tered water ill the Dakota sand at 1285 ft, and was abandoned in green shales of the Morrison at 1405 ft. Well cuttings from the Dakota sand showed some evidence of once containing oil, so a 1ocation was selected for No. 2 Fee on the east side of the river and on the upthrow side of the fault. Oil was discovered in Dakota sands ill 1935 by Continental Oil Co. in its No. 3 Hoye, NW.NW.NE. of sec. 34-9N.-78W., on the South McCallum anticline in North Park, Jackson County, Colo., but on account of heavy flows of carbon dioxide gas under high pressure it has been impossible for the company to get an accurate gage of the oil production. The freezing action of expanding carbon dioxide makes the producing of the oil difficult and costly.

Jan 1, 1936

By C. E. Shoenfelt

There were 110 important discoveries of either oil or gas in Co1orado in 1935. There was, however, further development of the Price structure in southern Colorado and developments since the first of the year indicate. that an important oil field may be in the making. The discovery of oil in Price structure was made by the Oil City Petroleum Co. late ill Novem-ber, 1934, in its No. 2 Garnett in the northeast corner of lot 3 in the SW.¼ of sec. 25-33N.-2E. This well developed a good showing of oil in Dakota sand at 970 ft. The hole filled up 15 ft. with 40° gravity oil overnight and after standing for several days the oil level was 400 ft. higher. As a result of the discovery of oil by the No. 2 Garnett, three wells were drilled by the William E. Hughes Estate. Two of these wells had good showings of oil and may make good producers but it is doubtful whether they will produce the estimated capacity of 500 bbl. each with which they have been credited. Although the Hughes Estate wells have been completed for some time, they have not been given thorough production tests because of the isolated position of the field and lack of proper facilities. The. first well drilled by the Hughes Estate was located on the west side of the Navajo River on the downthrow side of a fault. It encoun-tered water ill the Dakota sand at 1285 ft, and was abandoned in green shales of the Morrison at 1405 ft. Well cuttings from the Dakota sand showed some evidence of once containing oil, so a 1ocation was selected for No. 2 Fee on the east side of the river and on the upthrow side of the fault. Oil was discovered in Dakota sands ill 1935 by Continental Oil Co. in its No. 3 Hoye, NW.NW.NE. of sec. 34-9N.-78W., on the South McCallum anticline in North Park, Jackson County, Colo., but on account of heavy flows of carbon dioxide gas under high pressure it has been impossible for the company to get an accurate gage of the oil production. The freezing action of expanding carbon dioxide makes the producing of the oil difficult and costly.

Jan 1, 1936

By Alexander Deussen

The figures listed in a table for Gulf Coast fields given by L. P. Teas1 in 1934 are so greatly at variance with results that I have obtained from a serious study of this subject over a number of years, that I am disposed to challenge the correctness of Mr. Teas' figures as an accurate representation of acre-foot yields of Gulf Coast fields, and as regards at least two of the fields listed by Mr. Teas I desire to "put into the record" some figures that, according to my study, are more nearly in accord with what I conceive to be the actual facts. Upon investigation I find that Mr. Teas' figures, inadvertently no doubt, arc not what they purport to be. Apparently the figures were arrived at by considering as thickness of the producing formation the net thickness of producing rock corresponding "to the total of the net portions of the producing zones which actually yield oil into the drill hole"—and in following this method I am under the impression that Mr. Teas was acting under instructions of the Institute in the preparation of this paper, in order to get comparable figures from the several fields of the United States. Apparently the author interpreted these instructions to mean that in the absence of cored thicknesses of producing horizons the actual number of feet of screen set in the various producing zones was to be taken as the basis for arriving at the thickness of these zones and the "acre-foot" yields. It is obvious that in many instances only 20 ft. of screen, or even 10 ft. of screen, might be set in a well, when there might be actually 100 ft. of oil sand present. In the early operations in the Gulf Coast it was usual to set much less screen than the amount of sand. It follows that the "acre-foot yields" so arrived at would be much greater than those found by using the full amount of sand. In Mr. Teas' table, it was indicated that up to the end of 1933 "acre-foot" yields had been obtained in the several fields as listed in Table 1. A casual inspection of these yields will show that certainly they do not properly reflect the amount of oil produced from an acre-foot of the

Jan 1, 1936

By R. A. Pallanch

Sodium sulfite as a zinc retarding agent in the selective Hotation of complex lead-zinc sulfide ores was discovered by the writer in the summer of 1919 in the testing laboratory of the U. S. Smelting, Refining & Mining Co.'s gravity concentrator at Midvalc. Utah. It proved to be the first reagent to give consistently good results in the laboratory on the cornpanj's Bingham ore. In December, 1919, C. A Lemke, concentrator superintendent, recommended that a flotation unit be added to the existing gravity mill to handle the mill slimes, using sodium sulfite as the zinc depressant Owing to the poor lead and zinc markets and the unfavorable royalty schedules offered by the Minerals Separation Co., the project fell through at this time. In 1921, a number of laboratory tests were made at Midvale. on other ores, among them ore from the Sunnyside mine at Eureka, Chlo. Both sodium and calcium sulfites were used with succcss on this ore. Early in 1923, further tests were made at Eureka, shortly after the Sunnyside company had resumed operations after a two-year shutdown. AS a consequence sodium sulfite was given a trial in the mill. The results showcd sufficient improvement over previous work as to warrant continuous use of this reagent in the lead circuit Exeept for a week or so in 1926 and for several weeks in April, 1927, when sodium cyanide and zinc sulfate were given trial runs in this mill. sodium sulfite has been used ever sinee.. Sodium sulfite was chosen rather than the calcim sulfite brcauscl of its gre1ater sollubility, making it possitdr. to introduee the reagent as a solutiun. This Solution is introdueed into the Marry ball mills along with the original feed of ore,. The consumption of sodium sulfite in the Sunnyside mill varies from 1/4 to 12 lb per ton of ore, the smaller amount probably being nearer the average. In February, 1924, laboratory work at Midvale demonstratcd conclusivcly that good results could be obtaincd on the company's Bingham ore and on most of the custom ores tested by using sodiuin sulfite as the zinc depressant, xanthate as the lead enhancer in the lcad circuit, followed by copper sulfate and additional xanthate to float the zinc Sodium sulfide was used to float the iron pyrite after the lead and

Jan 1, 1928