Search Documents

By Henry F. Herley

The New Orient mine, owned and operated by the Chicago, Wilmington & Franklin Coal Co., has caused a great deal of comment and interest because of its unusual features and huge daily production. It is in Franklin County, Illinois, adjacent to the town of West Frankfort. The seam being mined is the Illinois No. 6 which in this locality is 9 to 12 ft. thick and lies approximately 500 ft. below the surface. Without fear of contradiction, it can be said that this is one of the largest coal mines in the world from a daily production standpoint. During 1928, New Orient produced 2,400,000 tons, which amounts to over 10,000 tons each day the mine operated that year. The mine is built for a capacity of 12,000 tons but has actually hoisted over 15,000 tons in one 8-hr, shift. This enormous production can perhaps be better visualized if it is realized that each day's operation depletes over two acres of coal. The general features of this mine have already been fully covered in a paper by George B. Harrington,' President of the Chicago, Wilmington & Franklin Coal Co. In a paper of the nature of Mr. Harrington's, it was unnecessary to stress any particular phase of mining conditions, consequently the ventilation problems were touched upon but lightly. In this paper an attempt has been made to describe some of the problems which have been encountered in providing adequate ventilation for the mine. Ventilating Conditions The acreage allotted to New Orient mine has a length, north and south, of approximately 6 miles, and a width, east and west, of 2 to 4 miles. A number of important considerations caused the hoist shaft, air shaft and surface plant to be located near the southeast corner of the property, instead of near the center, as is usual. During the initial phase of the mine development, the mine was ventilated through these shafts, although there was a full realization that at some future date other shafts would be required.

Jan 1, 1930

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Increase imports. 3. Develop new sources such as synthetic liquid fuels.

Jan 1, 1949

By Donald H. McLaughlin

ZEST in the search for new supplies of metallic ores and petroleum is difficult to maintain with stocks of raw materials accumulating and with over- production rightly or wrongly blamed for most of our industrial troubles. Enthusiasm over new methods of prospecting has consequently diminished and exploration programs in many fields have been drastically cur- tailed. Very naturally the effects have been felt with particular keeness in highly specialized phases of the work, such as geophysical prospecting, for the feverish scramble for new areas in which to drill beneath magnetic or electrical anomalies has abated, and there is even a lull in the firing in the battle over salt domes on the Gulf Coast. It is unquestionably an unhappy time for many of the organizations dependent on this work, but in certain respects the situation may be beneficial in correcting unsound practices that .have grown up through the necessity for haste and for quick decisions. With the restriction of the field to the more competent workers by the harsh rule of survival of the fittest, a general improvement, not only in technique but in business methods, can be expected which may go far in restoring public confidence. Geophysical prospecting in the short period that it has been utilized in North America, has suffered severely both from over-popularity and from excessive abuse. The former evil now

Jan 1, 1931

By Y. C. Liu, G. A. Alers

The anisotropy of Young's modules has been measured in a series of Cu-Zn alloys containing from 1 to 28 wt pct Zn and cold-rolled to 97.5 pct reduction in thickness. These modulus data show a transition in texture as a function of zinc content. In alloys containing 3 pct Zn or less, the texture is essentially that of copper. A transition is clearly seen to develop in 5 and 8 pct Zn alloys, and to have been completed in a 12 pct Zn alloy. Increasing the proportion of zinc to 28 pct does not produce any further changes in texture. The ease and clarity with which this texture transition can be seen in the modulus data is in great contrast with the inccertainty in the visual detertiination of the range of texture transition from a series of pole figures. It is also shown that the rolling texture of the high zinc content alloys cannot be a one-COIIIponenl texture, characterized by the (110)(112) ideal orientations, as usually assumed. A second, quite important component must also be present. Furthermore, the present data are inconsistent with matrix orientations on which the "oriented growth" hypothesis of the Formation of recrystallization textures is based. THE rolling textures of binary fcc alloy systems have generally been considered to lie between two terminal textures. One of these terminal textures is the copper type and the other is the 70:30 brass type. Alloys of intermediate solute content exhibit a texture which is said to be a transition between the two terminal textures. On the basis of efforts to correlate rolling and recrystallization textures, two concepts have been advanced in the literature on the nature of these transition textures. One school1 suggests that the addition of alloying elements, e.g., zinc, causes a gradual rotation about one of the (111) poles from the (358)( 523) ideal orientation of the copper-type rolling texture to the terminal {1 10)( 112) ideal orientation used to describe the rolling texture of 70:30 brass. This concept is depicted in Fig. 1 with the angle of rotation corresponding approximately to the zinc content and is designated here as the "rotational concept", since the ideal orientation of the transition textures varies continuously with alloy content. The other concept,' the "mixture concept", suggests that the copper-type rolling texture is a two-component texture. {358) (523) and {110)(112). The addition of alloying elements affects only quantitatively the relative amounts of these two components—a decrease in the amount of material in the {385}(523) orientation and an increase of that in the {110)(112) orientation with increasing solute content. An experimental distinction between these two concepts is essential to a better understanding of both the mechanism of formation of rolling textures and the subsequent formation of recrystailization textures in fcc metals. Because of the lack of resolution inherent in pole figures, it has not been possible to differentiate between the two concepts on the basis of this data. Both concepts, in fact, make use of the same set of pole figures but interpret them in a manner acco-rding to the view held.'" Experimental results obtained from inverse pole figures or selected-area electron diffraction3j4 simply -yield more refined pole figures but do not eliminate the ambiguity of interpretation. Quantitative measurement of an entirely different, orientation-dependent property must thus be considered

Jan 1, 1967

By William E. Ford, Edward Salisbury Dana

1. Normal Class (6) Zircon Type 2. Hemimorphic Class (7) Iodusuccinimide Type 3. Pyramidal Class (8) Scheelite Type 4. Pyramidal- Hemimorphic Class (9) Wulfenite Type 5. Sphenoidal Class (10) Chalcopyrite Type 6. Trapezohedral Class (11) Nickel Sulphate Type 7. Tetartohedral Class (12) Mathematical Relations to the Tetragonal System THE TETRAGONAL SYSTEM includes all the forms which are referred to three axes at right angles to each other of which the two horizontal axes are equal to each other in length and interchangeable and the third, the vertical axis, is either shorter or longer. The horizontal axes are designated by the letter a; the vertical axis by c (see Fig. 166). The length of the vertical axis expresses properly the axial ratio of a : c, a being uniformly taken as equal to unity. The axes are orientated and their opposite ends designated by plus and minus signs exactly as in the case of the Isometric System. Seven classes are embraced in this system. Of these the normal class is common and important among minerals; two others have several representatives, and another a single one only. It may be noted that in four of the classes the vertical axis is an axis of tetragonal symmetry; in the remaining three it is an axis of binary symmetry only.

Jan 1, 1922

By L. R., McLeod

NO important changes in metallurgical practice are exhibited in the smelter that has been erected for treating the Morenci concentrate: the material is charged to reverberatory furnaces without roasting, and the matte subsequently blown in Peirce-Smith converters to separate the iron and sulphur from the copper. In fact the process is essentially the same, except for preliminary roasting of the concentrate, that was adopted in the new smelter that was built for the Arizona Copper Co. at Clifton, a few miles away, to treat Morenci concentrate just before the start of the first World War, and which went into service in October, 1913.

Jan 1, 1942

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,' a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By J. V. Gluck

In the present paper," as in earlier publications, V1'2"1 the authors present experimentally obtained relations for the free energy of solution of oxygen in various metals as a function of temperature. The relations are linear and given in slope-intercept form. The authors give values for the "probable error" of the slope and intercept, citing Birge's method17 for obtaining these quantities. Birge discussed these methods as early as the period 1929-32.25726 In Ref. 25 the probable error is defined as "the numerical value which the true error is as likely to exceed as not", i.e., 50 pct probability. Ref. 26 is even more detailed and includes a lengthy discussion of the applicability of the Gaussian distribution to experimental data. However, the use of the "probable error" has come under some question. For example, Ezekiel'~ states that "the use of the probable error tends to make the results appear rather more accurate than the standard error". Moroney28 stated (in 1951) that "the term 'probable error' was used in former times to denote 0.67450 (50 pct confidence using the normal distribution)....the term, a poor one, is now very much obsolescent. It has been said that 'it is neither an error nor probable' ". Bennett and Franklin in 1954" in discussing statistical confidence levels mentioned that "the customary use of the 5 and 1 pct levels is not completely a matter of chance; these levels probably represent a balance between the desire to be correct and the desire to be specific. Also in most people's minds the borderline between something that could possibly happen and something that is not likely to happen is somewhere in this region. Certainly 5 or 1 pct confidence limits are to be preferred to limits such as the 'probable error' which has only a 50/50 chance of including the correct value." It may readily be seen that the 95 pct confidence level, which is given by 1.960 (assuming large sample size), thus corresponds to approximately three times the "probable error". Indeed, limits of one standard deviation correspond only to about 68 pct probability. Even if we triple the tolerances given by the authors in the equations of their Table 111, the deviations do not become excessive and would not detract from their excellent results. It could then be said with a high degree of confidence (95%) that the precision of the slope and intercept values is about *3-5 percent of their absolute levels rather than the 1-2 percent implied in Table 111. This is then compatible with an earlier suggestion of Gokcen~' of a probable accuracy of 5 pct in dissolved oxygen measurements by the technique employed. Alternatively, the authors could have

Jan 1, 1967

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94

Jan 1, 1917

[Aamot, Olav Crone, (M'29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M'38) Min. Engr., Dir. Bureau of Mines, Manila, P. 1. Abbott, Agatin, (J'40) Asst. Geol., Trench Mine, Patagonia, Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Tennessee Coal Iron & R.R. Co., 1642 Brown Marx Bldg., Birmingham, Ala. Abel, Raymond L., (M'28) Prof., Chem. Engrg., Univ. of Pittsburgh, Pittsburgh, Pa. Abel. Walter D., (M'32) Min. Engr., Div. of Corporations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M'31) 4800 Patterson Ave.. Richmond, Va. Abell, Leo M., (M'31) Research Met., Mount Morgan Ltd., Mount Morgan, Queens., Australia. Abenius, Hakan V., (M'37) c/o Falu Gruva, Falun, Sweden.]

Jan 1, 1940

Aamot, Olav Crone, (M'29) Chem. Engr., Elektro¬kcmisk, Raadhusgt. 32, Oslo. Norway. . Aase. Glenn D., (J'40) Jr. Met., American Smelt. & Refin. Co., Selby, Calif. Abadie, Henry G., (J'43) Petr. Engrg., Avenal, Calif. Abadilla, Quirico A., (M'38) Min. Engr., Dir., Bureau of Mines, Manila, P. I. Abbott, Agatin Townsend, (J'40) Jr. Engr., Phelps Dodge Corp., Morenci Branch. Morenci. Ariz. Abbott, Clarence E., (M'04) Civ. Engr. V.P., Tennessee Coal Iron & R.R. Co., 1542. Brown Mars Bldg. Birmingham. Ala. Abel, Raymond L.. (M'23) Chem. Engr., Com¬manding Officer, Pittsburgh Chem. Warfare urement Dist., American Bank Bldg.. Pittsburgh. Pa. Abel, Walter D., (M'32) Min. Engr., Supvr. Engr.. R.F.C., Los Angeles, Calif. Abele, Louis T., (M'31) 423 3rd Ave., Decatur. Ga. Abell, Leo M.: (M'31) Mill Supt. & Met.. Em¬ peror Gold Min. Co., Ltd., Vatukoula. Fiji Islands. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Fan. Abernathy, Jack H., (M'40) Cons. Petr. Engr., First National Bldg.. Oklahoma City, Okla.

Jan 1, 1943

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By T. B. Nolan, R. N. Hunt

In terms of present metal prices, analysis of extant records of the Eureka district indicate past production of the magnitude of $200,000,000 in recovered silver, lead, and gold. Production to date has been thoroughly oxidized ore from massive replacements, fissures, manta, and pipe-like bodies-in large part from the massive Eldorado (middle Cambrian) and Hamburg (middle to late Cambrian) dolomite horizons. In the productive area of about 6 square miles carbonate rocks comprise 80 per cent of the section, which includes early Cambrian to late Ordovician horizons. Four-fifths or more of the district's production came from a block of Eldorado dolomite in Ruby Hill that was moved in over younger horizons on strands of a regional thrust fault. The lower 500 to 600 feet of the block was much fractured and brecciated and became host to the ores. The Ruby Hill fault, a late normal fault, limits the Ruby Hill block of dolomite on the north for its entire length of nearly a mile and terminates the downward extent and exploitation of its ores. It introduced an hiatus of some 40 years in the district's development. Drilling of the past 20-odd years, followed by underground work, has now exposed the down-faulted extension of the Ruby Hill block of Eldorado dolomite and its contained ores, dropped 1800 feet in a dip shift to depths beneath the surface of 2000 to 3000 feet. The ores at depth are the sulfide counterpart of those mined in early years on the footwall side of the fault. The ores of the district may be attributed to the same source as the intrusive quartz diorite outcropping in a limited way south of Ruby Hill but found at depth elsewhere in drill holes. The long north-south axis of the district, its anticlinal structure, its major faults, and the distribution of the intrusives and, in their relation to the surface, the ores themselves, all suggest that erosion has not cut deep enough to expose the extent of intrusives and the ores consequent upon them.

Jan 1, 1968

By Waldemar Lindgeen

PART I.—General Features. PAGE Purpose and Extent of Inquiry ; Definitions (Fissure-Veins, Metamorphism, Metasomatism, Impregnation, Cementation, Weathering); Metasomatism in Connection with Mineral Deposits, Especially Fissure-Veins; Calcu lation of Analyses ; Criteria of Metasomatism; Crystallization of Sec ondary Minerals in Other Bodies; Secondary Alteration of Veins; Structure and Composition of Metasomatic Vein-Rocks and Their Rela tion to General Metamorphism,.759 PART 11.—Minerals Developed by Metasomatic Processes in Fissure-Veins. Quartz, including Chalcedonite and Opal; Rutile and Anatase; Fluorite; Calcite ; Magnesite and Dolomite ; Siderite; Muscovite and Sericite ; Biotite; Chlorite; Pyroxene and A mphibole; Garnet; Epidote ; Ortho clase ; Albite ; Tourmaline ; Topaz ; Kaolinite ; Zeolites ; Pyrite ; Mar casite ; Chalcopyrite ; Arsenopyrite; Pyrrhotite ; Galena; Zinc-blende and Other Sulphides; Tellurides; Native Copper ; Gold and Silver,. 601 Resistant Minerals,........... 619 PART III.—The Fissure-Veins Classified According to Metasomatic Processes. 1. Topaz-Cassiterite Veins (Altenberg and Zinnwald, Saxony ; Mt. Bischoff, Tasmania),..........620 2. Scapolite-Apatite Veins,.........625 3. Tourmalinic Gold-Copper Veins,.. 626 4. Biotitic Gold-Copper Veins,........ 641 5. Propylitic Gold and Silver Veins (General Features; Comstock Lode; The Veins of Nagyág, Hungary; Pachuca, Mexico ; New Zealand; Alaska ; Silver Cliff, Colorado; Silver City, Idaho),. .. .645 6. Fluoritic Gold-Tellurium Veins (Cripple Creek ; Other Occurrences),. 654 7. Sericitic and Kaolinitic Gold- and Silver-Veins (General Remarks; The Freiberg Veins ; De Lamar, Idaho; Summit District, Colorado),. . 6.58 8. Sericitic and Calcitic Gold-Silver Veins (The Gold-Quartz Veins of Cali fornia ; Idaho Types ; San Juan, Colorado ; Treadwell Mine, Alaska ; Gold Veins of Ontario, Canada; Schwarzwald Fissure-Veins),. . 664

Jan 1, 1901

By B. S. Butler

PART I SUMMARY CERTAIN relations between the formation of ore deposits and other geological processes are pretty generally accepted, namely: that many ore deposits are closely associated with igneous activity; that ore deposits accompany certain types of intrusive bodies, notably batholiths and stocks, and that they are concentrated near the tops of such bodies; that igneous activity occurs in belts of strong folding and faulting; that folding and faulting are greatest in basins of extensive sedimentation and least in areas of erosion or slight sedimentation; that areas of erosion or slight sedimentation and of heavy sedimentation persist over long periods and exert a major control over structure, igneous activity, and ore deposition; that cycles of erosion, deposition, folding and faulting, igneous activity, and ore deposition, have been repeated through geologic time resulting in rather definite periods in which metal deposits have formed. In short, ore deposition is but one phase of a series of closely related geological events. It is attempted in this chapter to point out the relations of these interreacting geologic processes to the distribution of ore deposits in the western United States. Three great periods of mineralization are recognized; pre-Cambrian, post-Jurassic, and late Cretaceous-Tertiary. In distribution the deposits of the three periods, with certain exceptions, show a concentration about two large positive areas, the Colorado plateau and the Columbia plateau, which suggests a causal relation. The most general age divisions of the rocks of the Cordilleran region of the United States are (1) pre-Cambrian, and (2) Cambrian and later rocks. The pre-Cambrian rocks are exposed mainly through the Rocky Mountain belt from the Canadian boundary southward to Arizona and westward through Arizona to southern California. They have commonly

Jan 1, 1933

By Earl R. Parker, Ralph Hultgren

DURING the past year publications in physical metallurgy have not been abundant when compared with the output of prewar years. Nevertheless, some noteworthy contributions have been made to the literature. Because of the necessity for war production, much of the metallurgical effort has been directed towards the solution of problems of production processes. The limited amount of time devoted to other problems is reflected in the small number of papers devoted to nonapplied research, though a few excellent contributions have been made to the fundamentals as will become evident in the following pages. Results of many of the government-sponsored research investigations have been released to the public and are being published in the technical journals. Many more of these papers may be expected to appear in the 1946 publications.. Public distribution of information obtained in the course of these investigations should be of great value to American industries in the postwar era. Continued activity in research of all kinds is apparently assured because of intense

Jan 1, 1946

By J. F. Lewis

Much has been written on this great engineering work, principally from the civil engineer's stand-point. In presenting the subject to the Institute, it seems necessary to include something of geology as well as engineering. In this case, it is particularly the glacial and post-glacial periods with which we are concerned; for it has been clearly proved that the canal recently excavated has not for the first time opened the Des Plaines valley for drainage away from Lake Michigan, and that this valley, as well as the site of this city, is very closely connected with the processes and effects of the ice period. We have simply renewed a channel and a drainage direction which formerly existed. As the days of deep water-ways for commercial purposes are fast approaching, engineers may find the consideration of ancient topography and geologic changes highly useful. For what I may say on this subject I am greatly indebted to Mr. Ossian Guthrie, who has made an earnest study of glacial geology and labored especially to decipher the records of its history in this region. * Chicago is situated in the track of one of four great glacial ice-streams that swept down from the North: one moving due South from Marquette and entering the Illinois valley at Ottawa; one through the Lake Michigan valley, entering the Illinois valley near Lemont; one from Saginaw Bay diagonally across the States of Michigan and Iadiana, entering through

Jan 1, 1898