Search Documents

By E. E. Brownson

This paper will be confined to the treatment of methods as applied in the laboratory of the Boston and Montana Reduction Department of the Anaconda Copper Mining Co. at Great Falls, Mont. As the electrolytic plant of this company operates at a current density of approximately 35 to 40 amperes per square foot when running up to capacity, the arsenic and antimony content of the anodes delivered to the plant is of considerable importance as bearing on the purity of the refined cathodes turned out. Owing to the rather high relative percentage of antimony, it has always been the custom to determine antimony as well as arsenic in all forms of copper. Thus, anodes have been analyzed in which the antimony was about equal to the arsenic, although the average shows about 2 parts of arsenic to 1 of antimony. In the refined copper the relative proportions of the two impurities vary considerably, but probably in the average are about equal. In this latter case, the percentage of the two is SO small that ordinarily no attempt is made to separate them, the report of analysis showing percentage of As and Sb combined. Although rapid and exceedingly accurate determinations of arsenic may be made by means of various distillation schemes, the determination of antimony, either by itself or together with arsenic, has always been more or less cumbersome and has required a considerable amount of time. By the methods, details of which follow, the determination of arseluic and antimony, either separated as in the case of anodes or together in case of refined copper, is accomplished in 24 hr. from the time the sample is received by the chemist. As to the accuracy of the results obtained, it can be quite positively stated that in this respect these methods are very satisfactory, much more so than any heretofore employed in our work, and when the rapidity of determination is considered, the results are very accurate.

Jan 1, 1914

By C. E. Van Orstrand

AN intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it will be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. H. Emmons,1 minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. MATHEMATICAL THEORY In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be assumed that the intrusive is a large parallelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, t = o), which has the same thermal properties as the intrusive, is2,3 [ ] In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. 'v = temperature at point x, y, z, time t. vo = initial temperature throughout the intrusive, t = o. K = coefficient of thermal diffusivity. a, ß, ? are variables of integration. Put n = m in Eq. I, and we have [ ]

Jan 1, 1944

By John J. Reed

Great strides have been made during the past few years in the field of rock mechanics, and steps have been taken to implement our newly acquired knowledge to advance the mining industry and improve the lot of the miner. This article is a summary of the latest progress in those areas of rock mechanics indicated by the subtitles. Let's look at these new tools for mining men. GROUND STABILITY DETERMINATIONS Much valuable information in the field of rock mechanics can be obtained by relatively simple, inexpensive measurements and observations, and this kind of investigation can be classed under the general heading of "Ground Stability Determinations." The instrumentation involved in this type of work is relatively simple and inexpensive, and its operation is not difficult to understand.1,2 Precise deformation measurements accurate to a few thousandths of an inch are very helpful in detecting stope convergence, pillar compression, floor heave, etc. Such measurements recorded over a period of weeks and months will detect and forwarn against failure of the overall mine structure long before any other visual evidence can be observed. Such advance warning then permits the introduction of sufficient artificial support in time to do some good. Instead of precise measurements which must be made with a special instrument, sensitive warning lights can be used which will flash red upon sensing movements as small as .002 or .003 in. These devices are well received by miners, and very practical under noisy conditions. High precision is important tit this area, but in large openings, engineer's tapes plus machinists scales reading to .01 in. may be sufficient. Uniform tensioning of the tape is of course essential. Long term, precise measurements have shown repeatedly that opening convergence lends to be slow and uniform except when accelerated to sudden large displacements by blasting, rock bursts or other sudden large scale failures. It is interesting to note that measurements in South Africa in very deep mines have shown 40% of the closure was footwall rise, and only 60% was hanging-wall sag.

Jan 4, 1962

By N. H. Murlenberg, T. M. Drown

It is often a tedious matter to get a solution of pig iron or steel, for the determination of phosphorus, which is absolutely free from silica. Where pig iron rich in silicon is dissolved in hydrochloric or nitric acid in the usual procedure, it is necessary, not only to evaporate the solution to complete dry ness, but to heat the dry residue for some beam in an air-bath to a temperature of about 120° C. The oxide of iron is thus rendered insoluble in nitric acid, and is only slowly dissolved by hydrochloric acid. In the method of determining silicon by nitric and sulphuric acid, described in the Transactions of the Institute, Vol. VII, page 346, arid Vol. VIII, page 508, we obtain in one or two hours a solution of the iron in the form of ferric sulphate entirely free from silica, and containing free sulphuric acid. It occurred to Us that this solution might be made available for the determination of the phosphorus by the molybdate method. The following experiments mere tried with unsatisfactory results. 1st. The iron was precipitated by ammonia, the precipitate filtered, washed, and dissolved in nitric acid. 2d. The iron was precipitated as basic acetate and dissolved in nitric acid. 3d. The solution was neutralized by ammonia, and nitric acid added in small excess. In all these cases the phosphorus obtained by precipitating by ammonium molybdate and magnesia-mixture was too low. The following method was then tried with success. The filtrate from the silica and graphite was evaporated to small bulk and heated in a porcelain dish on a sand-bath. until fumes of sulphuric acid ceased to escape. The dry residue was taken up with dilute nitric acid and the solution precipitated by ammonium molyldate. The phosphorus was weighed as magnesium pyrophosphate. The results were satisfactory. To save time, the original solution of the iron in nitric and sulphuric acids was evaporated to dryness and heated as before until

Jan 1, 1882

By N. H. Muhlenberg

IT is often a tedious matter to get a solution of pig iron or steel, for the determination of phosphorus, which is absolutely free from silica. Where pig iron rich in silicon is dissolved in hydrochloric or nitric acid in the usual procedure, it is necessary, not only to evaporate the solution to complete dryness, but to heat the dry residue for some hours in an air-bath to a temperature of about 120° C. The oxide of iron is thus rendered insoluble in nitric acid, and is only slowly dissolved by hydrochloric acid. In the method of determining silicon by nitric and sulphuric acid, described in the Transactions of the Institute, Vol. VII, page 346, and Vol. VIII, page 508, we obtain in one or two hours a solution of the iron in the form of ferric sulphate entirely free from silica, and containing free sulphuric acid. It occurred to us that this solution might be made available for the determination of the phosphorus by the molybdate method. The following experiments were tried with unsatisfactory results. 1st. The iron was precipitated by ammonia, the precipitate filtered, washed, and dissolved in nitric acid. 2d. The iron was precipitated as basic acetate and dissolved in nitric acid. 3d. The solution was neutralized by ammonia, and nitric acid added in small excess. In all these cases the phosphorus obtained by precipitating by ammonium molybdate and magnesia-mixture was too low. The following method was then tried with success. The filtrate from the silica and graphite was evaporated to small bulk and heated in a porcelain dish on a sand-bath, until fumes of sulphuric acid ceased to escape. The dry residue was taken up with dilute nitric acid and the solution precipitated by ammonium molyhdate. The phosphorus was weighed as magnesium pyrophosphate. The results were satisfactory. To save time, the original solution of the iron in nitric and sulphuric acids was evaporated to dryness and heated as before until

Jan 1, 1882

By T. F. Bower, M. C. Flemings

The classical explanation for formation of the fine equiaxed "chill zone " in ingot solidification is that local supercooling near the chill wall causes copious nucleation in this region. This work indicates, however, that convection is an essential element in formation of the chill zone. In the absence of convection, no chill zone forms even though rate of. heat extraction is extremely vapid. Alloy studied was Al-l.5 pct Cu alloy solidified against a copper chill wall. When solidification was initiated at the chill wall in absence of. cor-vection, surface grain size was large (>I cm diam). When it was initiated in the presence of convection, it was fine (<0.05 cm diam). It is concluded that some form of "crystal multiplication" plays an important role in formation of the chill zone. INGOT macrostructures are generally classed as containing one or more of the three zones: "chill zone", "columnar zone", and central "equiaxed zone". These three zones are sketched in Fig. 1; their origin has been discussed in some detail.&apos;-&apos; The classical explanation for formation of the chill zone is that supercooling occurs in the region of liquid metal adjacent the mold wall, and copious nu-cleation then takes place in this region forming numerous small crystals. The columnar region then results by growth of favorably oriented grains (den-drites) which crowd out their less favorably oriented neighbors."5 The mechanism of the columnar-equiaxed transition has been the subject of considerable interest. The generally accepted mechanism, until recently, was that constitutional supercooling developed in front of the growing columnar grains with eventual nucleation of new, equiaxed, grains ahead of the growing solid front.&apos; Recently, it became evident this explanation was not completely satisfactory and it is now evident that "crystal multiplication" plays an important role. This crystal multiplication occurs by separation of dendrite arms from growing dendrites,8?"&apos; and has been shown to be strongly influenced by convection.6, 10-13 Reduced convection results, for a given alloy, in longer columnar zone, larger columnar grains, and larger equiaxed grains.7, 12

Jan 1, 1968

By J. Allen Veatch

THERE exists in., the territory embraced between the summit of the Sierra Nevada and the coast a great dike and vein system that appears never to have been recognized in its entirety, nad many facts concerning it have never been published. This is important, not only in affording numerous clues bearing on the origin, nature, and age of the mercury deposits, and eliminating many controverted questions, but it. incidentally affords numerous facts bearing on the genesis of gold, copper, chromite, magnesite, dolomite, a type of calcite deposit, and numerous associated minerals. The mineral springs of the State almost without exception emanate from these dikes. A great range of the hydrocarbons also exists throughout the entire system of these dikes. Seepages from their, walls have frequently been mistaken as emanating from the inclosing sandstone and shale, resulting in heavy expenditures in the futile development of these Cretaceous beds, which contain no petroleum within the territory. The theory of mountain making by lateral or tangential pressure is inconsistent with some of the following recorded facts. The limitations of this paper do not admit of a description of each of the hundred or more mercury deposits embraced in the area, and therefore only typical examples will be described. The accompanying map, Fig. 1, is not submitted as complete, or as entirely accurate, but it is as nearly so as the notes at hand will admit. The field is too extensive to be completely covered by a single individual. The heavy continuous lines represent sections actually surveyed! The sections and extensions- in. dotted line are assumed, and are either unsurveyed, or -buried under younger beds. There are numerous branches connecting the great parallels that the small-scale map does not admit of plotting, even if the survey had been complete. Likewise, the conclusions in some instances may be faulty, but it is to be hoped that as a whole they may serve as a foundation on which a more complete structure may be built in the future.

Jan 2, 1914

By P. A. Beck, W. D. Manly

In a recent note Sully and Head1 showed that the Cr-Fe sigma phase is isomorplious with the Cr-Co gamma phase, and that the lattice constants are also nearly identical. In a preliminary investigation of the ternary Cr-Co-Fe system at 800°C at this laboratory the above findings were confirmed, and it was found by microscopic techniques, using various etching reagents, that the two binary phases form an urinterrupted series of solid solutions with each other. These solid solutions occupy a straight narrow band which cuts across the 800°C isothermal section of the ternary system, connecting the two binary phases. A detailed investigation of the Cr-Co-Ni ternary system at 1200°C disclosed that here, too, the Cr-Co gamma phase extends deep into the ternary system in the form of a long narrow lip. The fact that this sigma type lattice is sustained even when well over half of the Co atoms in it are replaced by Ni atoms, with relatively little change in the Cr content, clearly indicates that Ni itself has a certain tendency to form the sigma phase with chromium. This tendency is hidden in the binary Cr-Ni alloys, where the sigma phase is not known to occur, but it becomes operative in the presence of a suficient amount of Co. The interpretation of these facts in terms of electron concentrations is rendered difficult by the uncertainty of our present knowledge of the valency electron structure of the transition elements in their alloys. However, Sully and Heal&apos;s results and the present work suggest that intermetallic phases with signla type lattice may occur more frequently in these little investigated alloys than heretofore suspected. In particular, it is expected that a similar phase may exist in the V-Co and perhaps in the V-Ni system, in analogy to the known sigma type phase in the V-Fe system, and that all these sigma type phases may form extensive solid solutions with one another.

Jan 1, 1950

By Jose M. Sobral

The approximate production of petroleum in the various fields and for the country as a whole is shown in the following table, the figures for the later months of the year being estimated. Among the developments of the year may be mentioned the finding by the Standard Oil Co. of a small production, about 6290 bbl., at Aguas Blancas in the Province of Salta near the Bolivian border, and of about 88,000 bbl. at Lomitas, near Tartagal in the same province. The Government (Yaciementos Petroliferos Fiscales) in the last four months of the year also obtained about 6290 bbl, from Quebrada Galarce. .The oil found in Salta is of good grade and while the quantity is small great hopes of larger production are entertained. Approximate Total Argentine Production for 1928 Barrels Barrels Comodoro Rivadavia............................... 8,165,615 Plaza Huincul..................................... 783,514 8,949,129 Distribution of Production Government, Comodoro Rivadavia................... 5,165,159 Government, Plaza Huincul......................... 306,166 5,471,325 Private, Comodoro Rivadavia....................... 3,000,456" Private, Plaza Huincul............................. 477,348b 3,477,804 a The companies represented are Astra, 649,474 bbl.; Oriente, 42,237; Ferrocar-rilera, 1,337,380; Comp. Indust. y Comm., 609,092, Solano, 64,158; Diadema, 298,114. b Standard Oil Co. and a few smaller companies, Exploratory drilling has also been conducted around the Comodoro Rivadavia field. The Government is drilling at Vuela del Senguer south of Colonia Sarmiento and about 200 km. west of the main field hut the prospect of success is not as yet large. The country around Castillo, where the Royal Dutch Co. has property, is regarded more favorably. perhaps the most interesting event of the year was the discovery of a productive horizon at Comodoro Rivadavia about 200 m. below that previously exploited. This new horizon was found by the Ferrocarrilera Co. at 769 m. in its well No. 81, the previous yield for this

Jan 1, 1929

By Warden A. Moller

The Fushun coal-field, now being opened up by the South Manchurian Railway Co., is connected with the main line by a branch, 30 miles long, from Sui Chia Tun, 10 miles south of hlukden, the oapital of Manchuria. The coal-field, which lies on the southern bank of the Hun river, 25 miles east of Xiukden, consists of a long narrow valley, running east and west between hills composed of granitic and volcanic rocks. At the foot of the northern hills, the Hun river flows westward towards the Liao river, which drains the greater part of South Manchuria. At the foot of the southern hills, resting immediately upon volcanic rocks, and overlain by 30 ft. of alluvium, is a thick layer of Tertiary shales, carrying near the base two coal-seams. In many places the lower of these two seams is in immediate contact with volcanic lavas and basalts, the flows of which were evidently both prior and subsequent to the formation of the coal-seams. This contact has practically destroyed the lower seam for commercial purposes. The value of the field lies in the upper seam, which, for a length of nearly 8 miles, varies from 100 to 130 ft. thick. Of this seam, 85 per cent. is good coal. The seam dips to the north conformably with the shales, at angles of from 25 to 30°, and appears to have an uninterrupted dip for about 1.5 miles before being possibly cut oft&apos; by the northern hills. The coal-bearing shales extend east and west for a length of about SO miles, but towards the east the continuity of the seams is broken by intrusive rocks. The coal is of the sub-bituminous variety, low in ash, bright in appearance, and breaks with a conchoidal fracture. It has the usual qualities of Tertiary coal—quick steam-raising and poor stacking qualities. Pieces of resin, varging in size from

Jan 1, 1911

By Leonard Waldo

PROBABLY some of the views advanced in this paper will appear, from a metallurgical standpoint, little less than revolutionary. It is with considerable hesitancy that I venture to offer a few thoughts concerning what, seems to me to be perhaps the most important development of metallurgy since the introduction of Bessemer steel. Dr. John Percy, with that rare insight which characterizes the epoch-making man, described in a communication to the Royal Society, about 1855, an alloy of duminum and copper which he called aluminum-bronze. The name has "stuck." The term "bronze" has been so variously used that I confess I do not know exactly what constitutes a bronze; but I know that in the great materials of engineering simplicity of composition is a cardinal excellence; and I wish to venture the suggestion that aluminum-bronze is not an alloy of aluminum and copper in any such sense as the compounds of tin and zinc with copper (except the copper-tin compound SnCn3) are alloys. There are several reasons which lead me to this view. In the first place, if a series of bars be prepared containing varying percentages of aluminum and copper, and the electrical conductivity of these bars be carefully determined, a curve of conductivity will be obtained, as shown in Fig. 1, which represents the result of such experiments. While I am not sure, at this time, that the values of conductivity shown in this diagram are wholly dependent upon the percentage of aluminum added, the assumption is a probable one; and the curve indicates that an extremely small percentage of aluminum affects the conductivity in a ratio out of all proportion to the amount of that metal. Another reason is drawn directly from experience in the foundry. If we take from the furnace a crucible containing melted aluminum and one containing melted copper, both at a little more than a red heat, and pour them together, the reaction is so intense that the

Jan 1, 1895

By Nichols J. Grant, Bill C. Geissen

In low temperature phase diagrams, liquidus curves below about 1500°C are relatively easily established, e.g., by thermal analysis or separation of coexisting solid and liquid phases, followed by chemical analysis. Experimental difficulties increase considerably at higher temperatures and in systems involving more reactive metals. Although there are now thermocouples available for use from 1600" to 2400°c, as summarized by Caldwell,&apos; the need for frequent calibration, aging, and contamination problems, and unavailability of suitable protection tubes has sharply limited their use at higher temperatures. Many of the high melt- ing metals are found to react with refractory oxides. TO avoid such problems, a frequently used procedure is the diffusion and saturation method, as described by Spedding et a1.&apos; for the system La-C. This technique involves the annealing of one metal or a suitable alloy in a crucible of the other element at a temperature above the melting point, followed by chemical analysis of the center of the melt, after equilibrium is established. Further, if an alloy system is to be investigated employing the electron microbeam probe, and calibration charts have been established, it may be possible to measure the alloy concentration at the center of a cored as-cast structure, and to conclude from this points on the liquidus curve in a manner similar to the one to be described. It is known that in phases with a broad homogeneity range the rapidly cooled, cored, as-cast structure of an alloy presents concentrations having different lattice constants; this spread of lattice constant values contributes to the broadened lines of a powder pattern for the as-cast condition. The region of the crystal which is first to solidify will then correspond to the edge of the lines if the change of the lattice parameters with concentration is monotonous. In the course of the determination of the Ta-Tr phase diagram,3 it became evident that such behavior made it possible to construct the

Jan 1, 1963

By Ray Arms

This paper includes a brief classification of dry-cleaning devices, with a theoretical discussion of the principles involved. It outlines the methods of handling dust and screening difficulties at the McComas plant, as well as other plants that are being constructed and other dry-cleaning devices being developed. It describes the American Pneumatic Separator and discusses the sizing required, the effect of moisture in the raw coal, disposition of the middlings, and other aspects of the process. It gives s results of tests on various coals, and results of operation at Raton and McComas. DRY CLEANING, or pneumatic separation, is not, strictly speaking, a recent discovery. Among the archives of the Patent Office may be found many patents dating back as far as 1850 which cover early attempts to separate materials of varying specific gravity or of different shape by means of air. Hundreds of patents covering this art have been issued, which may be roughly classified into four general groups, as follows: 1. Stationary devices with pulsating air currents. The separating surface is usually riffled and air is supplied by bellows or compressors. This group&apos; also includes air jigs, which have been used rather extensively. 2. Stationary devices with continuous air currents. These submitted the material to a continuous current of air, either horizontal or vertical. Chaff is blown from wheat by such a device. 3. Reciprocating or vibrating devices with pulsating air. A small group in which the pulsating air is supplied by bellows and some motion provided in the separating surface to move the stratified material to various discharge points. 4. Reciprocating or vibrating devices with continuous air supply. This is by far the most important group and all recent developments have been along this line. All of the above groups involve the stratification of material by air and include none of the dry methods that use other principles, such as coefficient of friction, magnetism, etc.

Jan 3, 1924

By Robert Franke

(Butte Meeting, August, 1913.) IN view of the prominence which the conical mill has attained in the fine-crushing field .within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. . Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the immediately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years&apos; operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each. liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which. follow rolls crushing to 0.5 in.

Jan 7, 1913

In the January Bulletin a list was published of Societies&apos; publications, magazines, etc., which were duplicates and were discarded at the time of-the consolidation of the libraries of the three Founder Societies. A second list published herewith includes text books which are duplicates and which will be disposed of about April 1, 1916, by the Board of Directors of the Institute through the, Library Committee.. If, meanwhile, members desire to secure some of these books, they are asked to communicate at once with the Secretary as. this is an unusual opportunity to secure books at an extremely low price. Airy, George Biddell.-Magnetism, London, 1870, Bd. Alberti, Friedrich von.-Halurgische geologic. Erster Band. Zweiter Band. Stuttgart, 1852, Bd. American Iron and Steel Association.-Ann. Rep. of the Sec&apos;y. Statistics of American and, Foreign Iron Trades, 1877. Phila., 1877, Bd. Same, for year 1878. Phila., 1879, Bd. American. Telephone and Telegraph Co.-Ann. Rep. of Directors to Stockholders, 1911. N. Y., 1912, paper. Armagnat, H.-Induction Coils. Trans. by Otis Allen Kenyon, N. Y., 1908, Bd. Armstrong Cork Co. Insulation Dept. Nonpareil Corkboard Insulation. Pittsburgh, 1909, Bd. Associazione fra gli Industriali Metallurgici Italian.-The Metallurgic industry of Italy. Description of some of the principal works. Milan, 1911, Bd.

Jan 2, 1916

By Milton E. Wadsworth, T. D. Chatwin

Bulk density variations can usually be minimized by properly mixing the material before moisture measurement. The measuring of moisture on material being with- drawn directly from storage bins requires some form of bulk density correction. In Bethlehem&apos;s pellet plants continuous automatic bulk density correction and uniform feed-rate control are obtained with Bethlehem&apos;s patented Bin Level Control System. With this sys- tem a single probe, suspended or inserted in the bin, senses whether material is at the proper level in the bin and automatically regulates filter speed to control the filter-cake discharge rate to maintain this level. The level of concentrate in the filter-cake bin can thereby be controlled to within ± 1/2 in. of the point of contact between the concentrate and the probe. Material thickness on the conveyor does not have to be controlled accurately and mix compositions can vary widely as long as they do not contain variable amounts of water-soluble electrolytes. In sinter plants, errors caused by changes in normal feed rate and bed height are minimized by counter-weights that permit the free-floating to maintain a uniform contact pressure on the mix. Large changes in mix resistance can be taken care of either by resetting the control point or by adjusting the calibration control.

Jan 9, 1968

By Murray Kaufman

Using en; 41 for a base alloy, 15 modifications were made in sheet form. The elements Al, Ti, C, Mo, Co, and Cb were varied. The effects on the phases formed and their temperature dependence, the aging characteristics, tensile and stress-rup- ture properties, and weld cracking were determined. The A1-Ti content and balance is the most important factor influencing the major sCrengthening phases [Ni,Ti and Ni,(Al, Ti)] and, consequently, mechanical properties. THE mechanical properties, fabricating and joining characteristics, dimensional stability, and so forth, of alloys containing secondary phases are largely determined by the phases present, their distribution, and their temperature dependence. The phases in the basic ternary and quaternary Ni-Cr-Al-Ti combina- tions have been investigated thoroughly.&apos;* The phase behavior of many commercial nickel-base alloys has been determined also. In some cases, for example U500, 5 the effect on mechanical properties has been found. However, little systematic work has been done to clarify the action of each of the important alloying elements in controlling the phases formed in complex commercial alloys and their behavior. The effect of molybdenum on the carbides formed in M252 was investigated by Beattie and verSnyder.6 Application of the results provided by that work

Jan 1, 1963

By AIME AIME

A separate room in the suite occupied by the American Institute of Mining Engineers on the ninth floor of the United Engineering Society Building, has been equipped with furniture and telephone extension for the temporary use of members of the Institute or of sister societies, or visitors suitably accredited. .In addition to this general accommodation, another room has been similarly furnished as a business headquarters for a single person, and for a limited period. For the conditions of this privilege, inquiry should be made at the office of the Institute. . In order that the benefit of this arrangement shall not be restricted to a few members only, the period of continued occupancy will be limited, and applications will be considered in the order of their receipt. A small. fee will be required for the use of the facilities furnished. ANNOUNCEMENT. THE BIRMINGHAM MEETING. - The XCIVth Meeting of the Institute for the reading and discussion of professional papers will be held at Birmingham, Ala., beginning about October 1. After the Birmingham sessions and excursions, it is proposed to return by special train via Chattanooga, Ducktown, etc., to Washington, D. C., where additional sessions will be held. Further particulars will be given in a special circular, to be issued at an early day.

Jan 5, 1908

By Joseph G. Debanné

Foreword The three case histories and the liquid fuels planning scenario presented in this paper span a twenty year period, from the pioneering days of computers in the petroleum producing industry during the mid-fifties, to the energy crisis era of the seventies. Inasmuch as two of the main actors, Ian McKinnon and I, are featured in all three case histories, while I am currently involved in the fossil fuels scenario, this paper provides four related and personal spot readings along an evolutionary path: from the one dimensional technical domain to the multi-dimensional techno-socio-economic domain of computer applications in the petroleum industry. Coincident with this evolution in the direction of increasingly comprehensive and powerful computer applications, the evolution in hardware/software capability and in analytical power are also kept in perspective. The three case histories are: 1. The Bonnie Glen-Wizard Lake Case (Calgary, Alberta, 1955-1957); 2. The TransCanada-Great Lakes Gas Transmission Case (Ottawa-Washington, 1966); 3. The Westcoast Transmission - El Paso Pipelines Gas Export/ Import Case (Ottawa-Vancouver-Washington, 1966-1967). The liquid fuels planning scenario is a demonstration exercise rather than a case history; however, it represents an important point on the evolutionary curve and, provides a concrete example of tech-

Jan 1, 1977

By R. F. Miller, R. F. Campbell

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942