Search Documents

By H. F. Yancey, M. K. Geer

Investigations of the fundamental factors involved in the performance of various coal-cleaning processes have constituted a substantial portion of the research 011 coal cleaning conducted by the Bureau of Mines. These detailed studies of the mechanism of separating coal from impurity in various cleaning devices were undertaken to provide the coal industry with information that is helpful in selecting the type of cleaner most suitable for treating a particular coal. Previous reports describing these investigations have dealt with the wet table,1 the pneumatic table,' and the plunger,3 pulsator.4 and Baum types5 of jigs. The present report compares the performance of three commonly used units treating the same coal—a pneumatic jig, also known as the air-flow. cleaner, a pneumatic table, and a Baum-type jig. Object and Plan The fact that pneumatic coal-cleaning processes are less efficient than wet-washing methods because they are unable to make as sharp a separation between coal and impurity is well recogilized. The literature, however, contains little quantitative in- formation on the relative performances of the two types of cleaners. The object of the present report is to present a detailed comparison of the performances of two pneumatic units and one wet-washing process treating coal from the same bed. Although the information in this report demonstrates that the performance of the pneumatic cleaners is not as good as that of those employing water, it must not be construed as reflecting on the usefullless of such equipment. Performance is often secondary to other factors in the selection of coal-cleaning equipment, and the advantages inherent in pneumatic processes frequently outweigh the limitations imposed by their performance. Specific gravity and particle size are the principal factors that influence the separation of coal from impurity in either pneumatic or wet processes; consequently, the tools available for this investigation were the float-and-sink bath and the screen. Accordingly, the raw coal, clean coal, and refuse samples representing the operation of each type of cleaning unit were first separated into a series of density fractions by means of the float-and-sink bath, and then each density fraction was screened into a series of size fractions. By this procedure the raw coal, clean coal, and refuse were subdivided into components of restricted ranges in density and size. From these data it was possible to determine how the cleaning unit disposed of each component of the raw coal; that is. what proportion of each component is sent to clean coal or rejected as refuse.

Jan 1, 1947

By Gustav S. Preller, A. M. Gaudin

Fox the past 20 years it has been generally accepted that the flotation process is made possible as a result of the action of certain chemical substances on the surface of the mineral particles. In fact, it has been suspected, but never demonstrated, that this action produces on the mineral particles a layer of chemosorbed ions that is of the order of magnitude of a monolayer; that is, of a layer one ion deep. It is the purpose of this paper to present certain initial results on the relationship of mineral surface area and collecting-agent requirements. Up to about eight years ago, all considerations involving the surface area of finely divided solids were-limited by the fact that there was not in existence any general method for determining the extent of such surfaces, especially on mixed materials. However, the method invented by Brunauer, Emmett and Teller1 has changed the situation by providing a general procedure (BET method). This procedure has already been applied to mineral dressing problems2 -4 and has now received confirmation as to accuracy by an entirely independent method.5 This confirmatory or "absolute" method uses a very tedious calorimetric procedure and is not suitable for routine determinations; but still another method6 now is available to relate the results obtained by the BET method to those obtained calorimetrically. This Harkins-Jura method has the advantage that it does not require an assumption concerning the parking area per molecule of adsorbate (nitrogen). In the original work by Brunauer, Emmett and Teller the parking area per nitrogen molecule was calculated to be either 13.8Å2. or 16.2Å2. according as the nitrogen was assumed to be closely packed as in crystalline nitrogen or loosely packed as in liquid nitrogen. The initial experimental work from this laboratory2 supported the 13.8Å2. figure; that work was done on glass spheres of measurable geometric area and it was based on the assumption that the glass spheres were truly smooth; any deviation from this assumption would, of course, have made the calculated parking area higher. Harkins and Jura's results suggest that the parking area is not the same for all substrata; furthermore, the average of the 87 measurements cited indicates a "preferred" parking area for the nitrogen molecule of about 15.2Å2., with extreme values at 13.7 and 16.9Å2. The average of 21 determinations made in connection with this study' gave a parking area of 14.3 ± 0.27Å2. In view of this result and of the Harkins and Jura

Jan 1, 1946

By Gustav S. Preller, A. M. Gaudin

For the past 20 years it has been generally accepted that the flotation process is made possible as a result of the action of certain chemical substances on the surface of the mineral particles. In fact, it has been suspected, but never demonstrated, that this action produces on the mineral particles a layer of chemosorbed ions that is of the order of magnitude of a monolayer; that is, of a layer one ion deep. It is the purpose of this paper to present certain initial results on the relationship of mineral surface area and collecting-agent requirements. Up to about eight years ago, all considerations involving the surface area of finely divided solids were limited by the fact that there was not in existence any general method for determining the extent of such surfaces, especially on mixed materials. However, the method invented by Brunauer, Emmett and Teller1 has changed the situation by providing a general procedure (BET method). This procedure has already been applied to mineral dressing problems2-4 and has now received confirmation as to accuracy by an entirely independent method.' This confirmatory or "absolute" method uses a very tedious calorimetric procedure and is not suitable for routine determinations; but still another method6 now is available to relate the results obtained by the BET method to those obtained calorimetrically. This Harkins-Jura method has the advantage that it does not require an assumption concerning the parking area per molecule of adsorbate (nitrogen). In the original work by Brunauer, Emmett and Teller the parking area per nitrogen molecule was calculated to be either 13.8?2 or 16.2?2. according as the nitrogen was assumed to be closely packed as in crystalline nitrogen or loosely packed as in liquid nitrogen. The initial experimental work from this laboratory2 supported the 13.8?2. figure; that work was done on glass spheres of measurable geometric area and it was based on the assumption that the glass spheres were truly smooth; any deviation from this assumption would, of course, have made the calculated parking area higher. Harkins and Jura's results suggest that the parking area is not the same for all substrata; furthermore, the average of the 87 measurements cited indicates a "preferred" parking area for the nitrogen molecule of about 15.2?2., with extreme values at 13.7 and 16.9?2. The average of 21 determinations made in connection with this study7 gave a parking area of 14.3 ± 0.27?². In view of this result and of the Harkins and Jura

Jan 1, 1947

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By J. L. Lamont, W. Crafts

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By L. F. Mondolfo

An aluminum-copper 4 pct Cu alloy aged at room temperature for times increasing up to 78,000 hr was annealed at 170°C and the hardness and electrolytic potential determined during retrogression and subsequent aging. It was found that there is a change of behavior with increasing time of aging at room temperature which indicates that, given sufficient time, retrogression disappears and the room-temperature aging tends to progress directly into the high-temperature aging. WHEN an age-hardenable alloy is aged at low temperature after proper quench, changes of properties and structure take place. If this material is then heated to a temperature higher than the previous one, but still well below the solution-treatment temperature, the properties and structure changes produced by the low-temperature aging disappear and the material apparently reverts to the as-quenched condition, ready to undergo aging from the start. This phenomenon is termed reversion or retrogression. First discovered by Cayler3l it has been extensively investigated, as shown by the number of publications listed in the bibliography. From all the information available the following facts emerge: 1) All aeg hardenable alloys can be retrogressed.9 13, 19) 24, 33, 41, 42, 44, 47, 53, 54, 61, 63, 64, 66, 73, 78 2) All the properties changes that take place during aging at low temperature can be retrogressed to a smaller or larger extent.4,5,7,12,19,32,49,50,57,58,60,67,75,76 67, 75, 76 3) Retrogression requires that the temperature be well above the preliminary aging temperature. If the difference between the two temperatures is small, Little or no retrogression takes place.7,20,32,33,41,49 57. 65 4) The larger the difference between the preliminary aging and the retrogression temperature, the faster and more complete is the retrogression.20, 33, 41, 48, 65, 67 5) Retrogression can be produced several times in the same alloy.23, 35,41,57,59 6) The amount of retrogression that can be obtained depends on the aging temperature. Alloys aged at the lower temperatures can be retrogressed the most. The higher the preliminary aging temperature the less retrogression can be produced.20,25,33,37,44,49,54,58 7) Appreciable retrogression after aging at elevated temperatures is possible only if the preliminary aging has lasted a short time. After a certain time of aging at high temerature retrogression does not take place any more,:5,6,9,10,11,21,40,58 8) During retrogression the Guinier-Preston zones redissolve and disappear. The other precipitate

Jan 1, 1960

By R. D. Barer, M. B. Bever

Age hardening alloys are quenched from the solution treatment to room temperature in order to retain a supersaturated solid solution. Some alloys age "naturally" in this condition but in most alloys aging is induced "artificially" by heating to intermediate temperatures. Cold working of the supersaturated solid solution accelerates the aging process and quenching strains have the same effect. The investigation reported here is a study of the progress of aging in specimens quenched directly from the solution treatment to various aging temperatures. This procedure reduces the temperature interval of quenching and the resulting quenching stresses. It also eliminates any changes which would take place in the undercooled sample at room temperature prior to aging at an elevated temperature. Isothermal aging is thus approached and its kinetics may be studied. An aluminum-copper and an aluminum-silicon alloy were chosen for this investigation. The aging mechanism of aluminum-copper alloys is complex while the aging of aluminum-silicon alloys is nearly ideal. As standards of comparison for the samples directly quenched to the aging temperature, specimens were also age hardened by the usual procedure in which solution treated samples are first quenched to room temperature and then reheated to the aging temperature. Review of Previous Work The mechanism of age hardening has been the subject of a controversy which has ranged from the theory of outright precipitation of an equilibrium phase to theories based on subtle changes occurring in the matrix prior to precipitation. A detailed critical review of the literature up to 1939 is available1 and contributions to the general theory of age hardening continue to be made.2,3 Age hardening, whatever its mechanism, involves the nucleation of a second phase within a supersaturated solid solution. Theoretical considerations4,5 indicate that the rate of nucleation reaches a maximum at an intermediate temperature below the temperature at which supersaturation sets in. Studies of precipitation at various subcritical temperatures have demonstrated that the largest property changes in a given time occur at such intermediate temperatures.6,7,8 The precipitation of a phase from supersaturated solid solution is accelerated by strains which may result from quenching or cold work. Phillips and Brick9 established that quenching strains are an essential condition for the age hardening of aluminum-copper alloys at room temperature, at least for aging periods of less than 30 days. They also found that on aging at 300°C the hardness increased faster and reached a higher maximum after quenching into water than after quenching directly to the aging temperatures. Fink and Smith10 observed preferential precipitation on slip bands and grain boundaries in aluminum-

Jan 1, 1950

By C. L. Burrill

The forecasts presented in this paper constitute an attempt by the writer to predict the pattern of the consumption of petroleum products in the United States during the period of transition from war to peace. Although, in preparing the estimates, secular trends were not overlooked, greater emphasis was placed upon considerations of a cyclical character, or upon influences which might be peculiar to parts of the period. The estimates do not extend beyond the year 1950 because by then conditions in the industry should have returned to normal. The consumption of petroleum products is affected, of course, by changes in the condition of business in general. Before estimates of petroleum consumption could be prepared, therefore, it was necessary to predict the pattern of general business during the period under review, particularly the economic series that in the past have shown the closest relationships with petroleum consumption. It is the writer's view that business activity in this country (as measured by industrial production) will be higher on the average during the period between the end of the war and the year 1950 than it ever was before during a peacetime period of the same duration. When the war is over, consumers will have saved amounts of money that will be very large as compared with any previous accumulations. There is little question, therefore, as to the financial ability of consumers to purchase goods. The production of many durable consumers' goods, such as automobiles, refrigerators and radios, has been completely stopped since early in the war; also, many semidurable and nondurable consumers' goods have not been available in the quantities or the qualities desired. There is considerable needi therefore, for consumers to purchase goods after the war. The important question is whether consumers will purchase goods in "1arge enough quantities to keep our economy running at a high level. The writer answers this question in the affirmative. The mere existence of very large consumer savings lends considerable support to this view because, with such backlogs of " security," consumers can afford to spend more of their current earnings than they otherwise could. Also, several polls have been taken, which indicate that consumers expect to buy large quantities of a variety of goods. Some of the savings, therefore, probably will go into current consumption. Even though this percentage is relatively small, so that the bulk of the funds accumulated by consumers during the war continues to remain as savings during the period under review, spending should be great enough to start the production cycle and keep it

Jan 1, 1945

By C. E. Nelson

THE purpose of this discussion is to outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as far as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, the principal aim of this paper will be to deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux.* The flux provides protection during melting and a molten pool of flux into which the solid magnesium melts. It is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies; then on quiet standing separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is usually desirable. The open-pot method is used generally in the following processes: (I) alloying and secondary smelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings requiring hand ladling, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protec-

Jan 1, 1944

By John S. Brown

As a part of a symposium on the relations of structure to ore deposition, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replacement deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifications, to mineralization in unmetamorphosed limestone. In metamorphosed formations, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might faeilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a finc-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a limestone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone is of little or no importance.

Jan 1, 1941

By John S. Brown

As a part of a symposium on the relations of structure to ore deposition, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replacement deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifications, to mineralization in unmetamorphosed limestone. In metamorphosed formations, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might faeilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a finc-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a limestone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone is of little or no importance.

Jan 1, 1941

By C. Zener, H. Nielsen, D. Van Winkle

THE internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. EXPERIMENTAL METHOD The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress. The general method of making such measurements, and of observing the temperature of the specimen during a measurement, has been described elsewhere.5,6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and 900 cycles per second. SPECIMENS The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alphabrass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n ½ where n is the mean number of grains per square millimeter. EXPERIMENTAL RESULTS This paper is concerned exclusively with the part of the internal friction that becomes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By S. Suphi Yavasca, A. M. Gaudin

THIS paper is intended as a contribution to our knowledge of the mechanism of comminution and of the work of crushing. In a previous paper' it was shown that with quartz comminution proceeds as follows I. The size distribution of broken fragments made by a single fracture is such that the new surface on each grade is the same. 2. Multiple fracturing results in a size distribution such that in the fine sizes the surface per grade is the same in every grade; in coarse sizes the surface per grade decreases gradually with increasing size. In that paper it was mentioned that determinations on minerals other than quartz were in course of completion in order to establish the generality of these observations. In this paper, condensed data2 are presented for galena, pyrite and glass. Galena and pyrite are crystalline material and glass is noncrystalline. Galena has excellent cubic cleavage. Pyrite, although cubical, does not have marked cleavage. Quartz, on which the original determinations were made, does not cleave and although crystalline (hexagonal) breaks conchoidally. Glass breaks much like quartz. It is apparent, therefore, that the minerals selected represent some range in character of the solid without covering all possible types. GLASS Fifteen glass marbles were crushed individually in the pendulum crusher described in the preceding paper,1 then subjected to careful screening for 30 min. Six sized fractions were selected and cleaned in a hot 0.12 N solution of hydrochloric acid, washed with distilled water and dried on a hot plate. This was followed by an examination with a binocular microscope, to remove foreign matters not eliminated in cleaning as well as to eliminate "compacts" of fine particles. These compacts are groups of fine iragments that seem to be mechanically stuck together as a result of localized compacting during the comminution operation. The presence and the abundance of these compacts may be related to the amount and direction of the forces applied in different crushing devices. Since, properly, such compacts should be entirely eliminated in the sizing analyses, it is necessary to remove them to the last before making surface determinations on sized fractions. For example, with a - 28 + 35-mesh glass the surface areas of two samples, one cleaned with acid and under the binocular, the other only washed, were 102 and 172 sq. cm. per gram, respectively. Examination of the samples under an Ultropak microscope showed that washing alone failed to remove the compacts and also that it fails to remove certain fine dusts attached to the particles. Cleaning with acid loosens the fine dusts and

Jan 1, 1945

By Walter R. Hibbard, Ming-Kao Yen

VARIOUS rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two,1 three,2 five,4 an indefinite number,5 and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, † the necessity for the operation of slip systems capable of producing the required, changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: I. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, - the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only-not translation, inversion, nor others-is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal dose-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1948

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern&apos;s work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By Keith Leonard Sutherland

THIS paper is a study of the differential flotation of the sulphide minerals in the presence of salts of silver, lead and zinc. In practice, accidental activation due to these salts is more important than their use as reagents to replace copper sulphate. The general method of investigation has been based upon contact tests, the temperature of 35°C. being chosen in conformity with earlier work. Potassium ethyl xanthate and potassium amyl xanthate were selected as collectors and pure sulphide minerals were used. The experimental procedure has been outlined in earlier papers and all solutions were kept carbonate-free.&apos;&apos; Contact, or spreading of an air bubble, at a mineral surface indicates the presence of an adsorbed collector film. PURITY OF REAGENTS The xanthates were purified in the usual manner.1 Neither the cyanide nor the sodium hydroxide solutions contained sufficient carbonate to give a precipitate with barium chloride solution. The silver sulphate was prepared from pure silver nitrate by evaporation with concentrated sulphuric acid until there was no evidence of brown fumes. This solution was diluted and the difficultly soluble sulphate washed with water so that unchanged nitrate was dissolved. The resultant crystal-line powder was pure white. The lead and zinc salts were prepared by dissolving especially pure lead and zinc in C.P. nitric and sulphuric acid solution and the crystals drained. The standard solutions were checked by titration. It was felt desirable to use the sulphate radical wherever possible, but since lead sulphate was insufficiently soluble for the purpose of the experiments, it was necessary to use some other lead salt. A.R. copper sulphate was used without further purification. RESULTS The results are presented in the accompanying figures; the areas of noncontact (nonflotation) are shaded in Figs. 8, 9, 10 and 11; in the remainder they lie to the right of the curve. Zinc Sulphate The curves in Fig. I are to be compared with those for Fig. 2, for which zinc sulphate is absent. This comparison shows that the influence of the zinc ion is usually small. Its influence is more marked, however, for chalcopyrite in the absence of cyanide. The influence of zinc sulphate is also marked for copper-activated sphalerite, for which tests were made only in the absence of cyanide. The results are of importance in the separation of pyrite from copper-activated sphalerite when zinc sulphate is added in the lead flotation section (p. 204 of ref. I). Sphalerite does not adsorb the collector (i.e., become floatable) under the conditions chosen.

Jan 1, 1942

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

A simple reproducible method was developed for determining the ignition temperatures of magnesium and magnesium alloys and by this method magnesium and over 100 magnesium alloys were measured. The ignition temperature of magnesium was determined in O2-SO2, O2-N2 mixtures and in O2 from 0.166 to 10 atm pressure. The ignition temperature of magnesium is generally lowered by alloying and increased by an increase in oxygen pressure. WITH the expanded use of magnesium alloys in industry, ignition temperatures are of considerable importance, especially in heat treating and for service at elevated temperatures. Magnesium alloys exhibit a relatively slow linear oxidation rate up to temperatures near the melting point.&apos; At some critical temperature the rate of oxidation becomes extremely rapid. This high rate of oxidation is accompanied by the emission of light and additional characteristics suggesting a flame. The literature concerning the ignition temperatures of magnesium and magnesium alloys is relatively incomplete and the values reported by various authors are not in agreement. The most probable reasons for this are: 1—The absence of a suitable definition of ignition, and 2—the need of a standardized method of determining the ignition temperatures of inflammable metals and alloys. The exact date of the discovery of the fact that magnesium will ignite and burn is unknown. It is likely that H. Davey encountered this property of the metal during its preparation in 1808. The first reference in the literature specifically on ignition of magnesium is by Lenze, Metz, and Rubens.&apos; They investigated the inflammability of certain magnesium alloys. Brown3-&apos; reported that magnesium ribbon will ignite in air at 507 °C by what was called the rising temperature method. Hartman, Nagy, and Brown" reported that magnesium powder ignites from 475" to 560°C depending on particle size. According to Guise, Mars, and Wilson prolonged heating in air at 427°C of common casting magnesium alloy causes it to ignite. Samples of magnesium alloys were placed directly in the flame of a torch by Carapella and Shaw.&apos; These investigators obtained some evidence of melting prior to ignition. For commercial magnesium, they reported an ignition temperature of 650°C. Their values varied from 450" to 800°C for magnesium alloys. Willmore and Peterson" studied the effect of air velocity, humidity, rate of heating, and foreign metal contact on the ignition temperature of magnesium. They conclude that melting is not a prerequisite for ignition and that the conditions which influence ignition are complex and difficult to analyze. The only quantitative theoretical treatment of the ignition temperatures of magnesium and magnesium

Jan 1, 1952

By Louis C. McCabe

The control of dusts and fumes of submicron size is involved in many process industries. This paper presents in tabular form the quantitative data from a number of metallurgical operations and discusses allowable discharge in terms of effluent-weight ratio. Typical installations for recovery of stack effluents are cited. THERE are many sources of smoke, fumes, gases, and dusts that may cause undesirable contamination in an industrial area. Fumes and gases are the result of chemical action or volatilization, while dusts are produced in processes of disintegration and dispersion. Commonly, smokes are suspended particles formed by combustion or destructive distillation. Methods for controlling smoke are generally known, and great improvements have been made in equipment for removing fine dusts and fumes from gases. In most of the industrial centers of the country, the chief duty of the air-pollution abatement agency is the elimination or reduction of emissions resulting from improper combustion. Correct methods of firing, proper fuel selection, and installation of properly designed equipment may accomplish this. It is becoming more widely recognized that much of the contamination of an industrial atmosphere is caused by dusts, fumes, and gases that are not related to the process of combustion. As such emissions are usually a functional part of plant operation, they rarely can be prevented even by better design and careful operation. When dusts, fumes, and gases are an integral part of the operation, mechanical equipment must be designed to remove these emissions. Most of the dusts and fumes that should be controlled are less than 1 micron in size. Control of such small particles is largely a new and untried field in many industrial areas. However, where conditions have been critical, effective control equipment for dusts, fumes, and gases has been in operation for many years. The problem is not one of smoke abatement and requires an entirely different set of standards for effective solution. Identical standards need not be applied to all industrial areas because of differences in meteorology, physiography, plant location, plant density, and nature of stack effluents. In this paper, discussion of control of atmospheric contamination by industrial plants refers specifically to the Los Angeles area, but the method of approach is applicable to any area where similar problems are encountered. Quantities of particulate matter reported in analysis of stack effluents indicate the need for standards of emission. Many types of dusts and fumes that contribute materially to the air-pollution problem are discharged into the atmosphere at a lower rate than 0.40 grain per cu ft at standard conditions. On the other hand, some stacks discharge at a higher

Jan 1, 1951

By John S. Brown

As a part of a symposium on the relations of structure to ore deposition, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replacement deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifications, to mineralization in unmetamorphosed limestone. In metamorphosed formations, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuitability or resistance to replacement, and (b) physical resistance to small-scale brecciation, which might facilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a fine-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a limestone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone is of little or no importance.

Jan 1, 1940

By Louis C. McCabe

The control of dusts and fumes of submicron size is involved in many process industries. This paper presents in tabular form the quantitative data from a number of metallurgical operations and discusses allowable discharge in terms of effluent-weight ratio. Typical installations for recovery of stack effluents are cited. THERE are many sources of smoke, fumes, gases, and dusts that may cause undesirable contamination in an industrial area. Fumes and gases are the result of chemical action or volatilization, while dusts are produced in processes of disintegration and dispersion. Commonly, smokes are suspended particles formed by combustion or destructive distillation. Methods for controlling smoke are generally known, and great improvements have been made in equipment for removing fine dusts and fumes from gases. In most of the industrial centers of the country, the chief duty of the air-pollution abatement agency is the elimination or reduction of emissions resulting from improper combustion. Correct methods of firing, proper fuel selection, and installation of properly designed equipment may accomplish this. It is becoming more widely recognized that much of the contamination of an industrial atmosphere is caused by dusts, fumes, and gases that are not related to the process of combustion. As such emissions are usually a functional part of plant operation, they rarely can be prevented even by better design and careful operation. When dusts, fumes, and gases are an integral part of the operation, mechanical equipment must be designed to remove these emissions. Most of the dusts and fumes that should be controlled are less than 1 micron in size. Control of such small particles is largely a new and untried field in many industrial areas. However, where conditions have been critical, effective control equipment for dusts, fumes, and gases has been in operation for many years. The problem is not one of smoke abatement and requires an entirely different set of standards for effective solution. Identical standards need not be applied to all industrial areas because of differences in meteorology, physiography, plant location, plant density, and nature of stack effluents. In this paper, discussion of control of atmospheric contamination by industrial plants refers specifically to the Los Angeles area, but the method of approach is applicable to any area where similar problems are encountered. Quantities of particulate matter reported in analysis of stack effluents indicate the need for standards of emission. Many types of dusts and fumes that contribute materially to the air-pollution problem are discharged into the atmosphere at a lower rate than 0.40 grain per cu ft at standard conditions. On the other hand, some stacks discharge at a higher

Jan 1, 1951