Search Documents

By Pramod C. Thakur

Introduction Methane is contained under pressure within the fractures and adsorbed on the surface of the coal seams and adjacent strata. It is released into the mine atmosphere during mining of the seam creating explosive gas-air mixtures. Large volumes of air, sometimes as high as 20 tons of air for each ton of coal mined, are circulated constantly to dilute and carry away methane from coal mines. Removal of methane from solid coal, wherever high methane emissions occur, has been discussed by Spindler and Poundstone (1960) and Thakur and Davis (1977). Methane control in longwall gobs is much more complicated. As longwall mining progresses, the overburden continually subsides, and the immediate roof caves behind the roof supports. Even the underlying strata heave and open up communication channels feeding gas to the longwall gobs. The pressure of gas in the underlying and overlying strata is usually higher than the ambient air pressure in the mine. Thus the mine workings become natural pressure sinks, into which gas flows from the entire disturbed zone. Winter (1975) defines this zone as the "gas emission space". Depending on the number of gas-bearing zones in the gas emission space and their gas contents, the total methane emission from longwall gobs could vary from a few to more than one hundred cubic meters of gas per ton of mined coal. Hence the ventilation of longwall faces demands a large quantity of air. This ventilation need is further enhanced by high air losses specially on caving faces (with no stowing of the gobs). The old system of longwall ventilation, the 'U' pattern, where all the air was brought down one gate road and exited through the other gate road, loses large quantities of air through gobs giving a high methane concentration at the return end of the face. The 'Y' ventilation pattern where intake air is brought down both head and tail gate roads relieves the situation to some extent but, on most longwalls, some kind of methane control is still needed. With the onset of longwall mining in Europe several decades ago, the initial work on methane control on longwall has naturally been done there. The basic principle of methane control has always been, and still remains, some means of "bypassing methane from the gas emission space without letting it mix with the mine air". In most cases the bypassing mechanism is either a strategically located borehole or a roadway. A successful methane control program depends on the following basic premises: a. Determination of the geometry of the gas emission space and location of gas bearing horizons therein. b. Estimation of the rate of methane influx into the longwall gob. c. A scheme to bypass the gas in the most economic and efficient manner and thus prevent it from entering the mine atmosphere. In successful methane drainage programs a high proportion, usually between 50 and 70 percent, of the total gas emissions in a working district is removed before it can enter the mine airways. Advantages of methane drainage can be summarized as: 1. Generally reduced methane levels in the mine leading to increased safety and productivity. 2. Reduced air requirements and corresponding savings in ventilation horsepower. 3. Faster rate of advance for development headings and economy in the size of headings. 4. Possible use of mine gas as an additional source of fuel. The purpose of this paper is to briefly review the geometry of gas emission space and methane influx therein and discuss more successful European and U.S. longwall gob gas control techniques.

Jan 1, 1981

By M. Kaufman, D. Rosenthal

IT would be of great importance to our understanding of the phenomena of fracture in metals if a unique relationship could be established between stress and some easily measurable parameter of deformation up to the fracture. It is known that no such relationshir, has been found when the parameter was the mechanically measured strain,' the major part of which is plastic. The present investigation was initiated to determine, among other things, if the X-ray or lattice strain" might be a • For the definition of lattice strain see ref. 2. more suitable parameter. To this end, annealed stress free*' specimens of 61s aluminum alloy were ** Freedom of stress in this particular case means absence of those stresses which can be checked by the technique employed. tested at room temperature and liquid nitrogen temperature (—195OC), by first maintaining the same temperature from the beginning until the end of the test, and then with crossovers from one temperature to the other. Three major factors had to be taken into consideration in designing the specimens and testing equipment. The test setup must allow X-ray pictures to be taken while the specimen is under load (for as much as 2 hr at a given load). Provision must be made for maintaining the test specimen at the temperature of liquid nitrogen as well as at room temperature. In addition, the specimen must be able to rotate to allow the X,ray beam to take in as large a sample of grains as possible, to maintain centering, and to correct for effects of large grains. The final design of the specimen and equipment is shown in Figs. 1 and 2. The specimen and grips are hollow, enabling liquid nitrogen to be poured in through a funnel-container arrangement while the specimen is rotating. The diameter of the specimens at the 2 in. gage section is 5/16 in. with a 3/16 in. diameter hole through the center. A small pilot valve in the lower grip allows a very small stream of liquid nitrogen to escape, thus assuring circulation of the liquid at all times. A low temperature silicone grease-tissue paper packing is used to seal all joints. The specimen is held in the grips by a pin. Spherical socket joints at top and bottom are used to allow for proper alignment. The grips are connected to the thrust bearings by means of plastic couplings to decrease the heat flow. Rotation is accomplished by means of a motor which drives a plastic gear (integral with the lower coupling) through a semiuniversal joint to allow for deforma- tion of the specimen. The torque applied to the specimen is very small. The maximum stress caused by this torque at the highest loads reached was found to be less than 200 psi, The whole unit was mounted in a 10,000 Ib testing machine. An insulation cage was placed around the specimen to cut down air circulation, and consequent frosting of the specimen, and also to reduce radiation and convection heat losses. A narrow window, covered on both sides with a thin plastic materiai allows the X-ray beam to reach the specimen. Thermocouples placed just outside the pilot hole at the lower grip, in the bottom of the funnel container and near the top of the funnel container permitted checks of the

Jan 1, 1955

By F. F. Skiba, J. E. Warren

An idealized miscible displacement process in a three-dimensional, heterogeneous porous medium has been studied via experimental computation based on a "Monte Carlo"' model. The macroscopic dispersion which results solely from variations in the permeability of the porous system is related to the scale of the heterogeneity as well as the distribution function for the permeabilities. The interpretation of laboratory data is often subjective and may bt? misleading since ambiguities are not always recognized. Furthermore, an experiment performed on a conventional oil-field core does not yield a valid measure of Macroscopic dispersion for reservoir engineering purposes since the scale of heterogeneity that is significant in the laboratory is not significant in the reservoir. The analysis of field-performance data is discussed and it is shown that a unique characterization of the reservoir can not be obtained from this information alone. A possible method based on a minimum of data, for estimating the spatial distribution of permeabilities in a reservoir is postulated INTRODUCTION Many studies concerned with diffusion and dispersion in porous media have been undertaken because of the potential importance of miscible displacement processes for increasing the recovery of oil. The results from a large number of these studies have been published; in a recent paper Perkins and Johnstonl presented a comprehensive survey of the pertinent literature and excellent appraisal of the "state of the art". In this investigation, dispersion resulting from macroscopic variations in the properties of the porous medium is of primary interest. Dispersion, in this sense, is caused by fluctuations in the velocities of the individual fluid elements as they move through the porous system. This phenomenon is the result of inhomogeneities in the permeability and/or porosity, but it can be amplified by differences in the characteristics of the fluids involved. The objectives of this study are the following: (1) to determine the qualitative manner in which macroscopic rock properties affect the observed dispersion coefficient; (2) to evaluate the possible influence of macroscopic dispersion on laboratory experiments; and (3) to appraise the significance of macroscopic dispersion with regard to reservoir performance. Investigations of this type are essential since many miscible displacement processes, while seemingly understood from a mechanistic point of view, do not behave in a predictable manner under field conditions. Although a plausible explanation is that the process is dominated by the environment, little serious effort has been devoted either to describing the reservoir itself or to determining the probable effect of the reservoir properties on the process. This study is intended to be exploratory in nature; however, it is hoped that it will provide additional insight into the physical problem and that it will suggest areas suitable for further investigation. EXPERIMENTAL COMPUTATION MODEL To limit the observed dispersion to that which results solely from variations in the properties of the porous medium, an idealized process in which one incompressible fluid displaces another identical fluid is simulated. This simulation is achieved by means of a modified Monte Carlo method — by tracking a number of mathematical particles (tracer) through the system according to the steady-state, single-phase velocity distribution. Then the system is characterized by the distribution of the residence times of the particles. Since any number of particles can be injected simultaneously (a true delta-function distribution) and only pressure conditions are imposed on the boundaries, the model is completely determinate. Furthermore molecular diffusion, microscopic dispersion, adsorption and/or reaction are automatically precluded from the model. The heterogeneous medium is represented by a rectangular, three-dimensional array of uniform, homogeneous porous blocks which are randomly arranged; it is assumed that any two opposing faces of the system are held at fixed potentials

Jan 1, 1965

By M. R. Geer, H. F. Yancey

WITH the exception of pneumatic processes and ii few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral- dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficiation process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and else- where, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment for many years, and more recently driers employing centrifugal force have gained in popularity. 1 A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal-a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. OBJECT AND SCOPE OF INVESTIGATION Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it on coal slurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1948

By J. Doig, A. A. Bauer, F. A. Rough

AN investigation of the phase relationships between the 6 phases of the uranium-molybdenum and uranium-titanium systems was conducted by studying alloys ranging in composition from uranium-31.5 at. pct Mo to uranium-34 at. pct Ti. A ternary cut showing these phase relationships is presented upon the basis of thermal-analysis data obtained and upon the basis of metallographic and X-ray examination of heat-treated and quenched specimens. Isothermal ternary sections, inferred from phase relationships determined between the two 6 phases, are presented for the uranium-molybdenum-titanium system. In the compositional range investigated, a y-ura-nium solid solution exists at elevated temperatures. At about 900°C the 6-U2Ti phase, with limited molybdenum solubility, forms. Epsilon, a molybdenum-titanium-rich solid solution appears at the same temperature and appears in all phase regions that exist below this temperature except in the terminal 6-phase regions. The y phase is stable to approximately 660°C in titanium-rich alloys; the y and 6-U,Ti phases decompose at this temperature to a uranium in a peritectoid reaction. The y phase in molybdenum-rich alloys of the ternary cut studied decomposes in an apparent eutectoid reaction, at about 593°C, to the 6-uranium-molyb-denum and a-uranium phases. The e phase while present, presumably plays a negligible role in these reactions. Titanium was found to markedly decrease the stability of retained y in these alloys. Age-hardening characteristics developed in titanium-contain ing uranium-molybdenum alloys quenched from 900°C and aged at 500°C are ascribed to decomposition of Y to the a and E phases. INTRODUCTION Alloys of uranium with molybdenum, titanium, and zirconium, respectively, are of great interest because of their potential use as reactor fuels. As a result, this interest extends to the constitution of these alloys, particularly in view of their uniqueness of constitution. In these systems, alone, among known uranium-alloy systems, an intermediate phase forms by direct decomposition of the high-temperature y-uranium phase. As a prelude to possible future alloy development, an investigation has been undertaken of the phase relationships that occur between the intermediate phases of these systems. These phase relationships have already been reported for the intermediate 6 phases of the uranium-zirconium and uranium-titanium systems.' The results of an investigation of the phase relationships between the 6 phases of the uranium-molybdenum and uranium-titanium systems are reported here. The phase relationships that occur in the binary systems pertinent to this investigation are shown in Fig. 1. Phase nomenclature appearing throughout this report is as shown in these diagrams; the crystal structure of the phase is given in Table I. EXPERIMENTAL PROCEDURE Alloys were cast and fabricated to flat plate. Specimens were heat treated and examined metal-

Jan 1, 1959

By Robert E. Cuthbertson

It is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson,= by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be corfined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. Brief History of Reagent Practice at Climax Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 19-20, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Nevertheless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1947

By Robert E. Cuthbertson

It is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson,= by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be corfined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. Brief History of Reagent Practice at Climax Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 19-20, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Nevertheless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1947

By R. J. Teitel

FOUR or five years ago an investigation was initiated to study and develop basic information on llquid metal fuels for future power nuclear reactors. The objective was to find fluid forms of uranium (solutions or dispersions) in low melting alloys. A summary of the different fuels was presented in a recent article by Teitel, Gurinsky, and Bryner.' The combination of uranium and bismuth, with its low thermal neutron cross section and low melting point, is of basic interest to the development of these fuels. Most of the previous effort on the U-Bi phase diagram was done under security regulation. Ahmann and Baldwin' reported their findings on the U-Bi system in 1945. Their results indicated that the phase diagram had at least two compounds and possibly one more. UBi, and UBi were established by chemical analyses of residues after high temperature centrifugation of alloys. UBi, decomposed peritectically at1980°C and there were signs of another reaction above that. UBi melted at a very high temperature, and there were also signs of a monotectic at high temperatures in high uranium alloys. The solubility of uranium in liquid bismuth has received attention by three groups of authors: Bareis,X ayes and Gordon,' and Ahmann and Baldwin.' The latest and most widely accepted data is that of Bareis, and it is included in Fig. 1 along with new data at higher temperatures. Brewer et al." and Ferro"'' have used X-ray diffraction to determine the number and crystal structure of the compounds. Brewer identified the structure of UBi to be a simple NaCl cubic structure having a cell edge of 6.364A. The density of the compound was calculated to be 11.52 g per cu cm. Two other unindexed patterns were presented as possibly belonging to two other compounds. Ferro agreed with Brewer on the crystal structure of UBi and identified the structure of UBi, and U,Bi,. The intermetallic compound UBi, has a tetragonal cell with a = 4.445A and c = 8.908A. The density of the compound was determined and the number of atoms per cell (six atoms) was calculated. The X-ray density reported was 12.35 g per cu cm. The compound UsBir was treated in a similar way and it was reported to have a cubic structure 9.35A on an edge and to contain 28 atoms per cell. The density was given as 12.59 g per cu cm. Teitel reported that there was a compound UaBi, and no UBi, compound. (The difference in the compositions is 3.3 pct U.) This conclusion was based upon the extrapolation of some 20 tie lines in the

Jan 1, 1958

By M. R. J. Wyllie, P. F. Southwick

The importance of the so-called "dirty sand" or "conductive solids" problem in electric log interpretation was first stressed in a paper presented in 1949. Since that time the problem has been generally recognized as a most serious one. Several research papers bearing on the theory of the effects of clay contaminants on reservoir rock resistivities have appeared. These papers, while contributing to the theory of the problem, have not offered any practical solution. In the present paper an experimental investigation has been made of the effects of ion-exchange materials on the electrical properties of natural and synthetic porous media. The method used to make synthetic dirty sands is entirely novel and has proved a valuable guide to a better understanding of the properties of dirty sands generally. The effects of ion-exchange materials on both the resistivity and self potential (S.P.) logs have been examined. From the data obtained it has been possible to formulate a simple, practical method whereby electrical logs of dirty sands can be qualitatively interpreted. The method is in all essentials identical to that presently in use for interpreting clean sands. New light has also been thrown on the significance of the term formation factor when it is applied to dirty sands. In 1949 a paper was presented1 which showed that the presence of so-called "conductive solids" introduced considerable complexities into the analysis of the resistivities of dirty sands, i.e., permeable formations containing clay. The reduction of the self potential (S.P.) resulting from the presence of interlaminated shale or interstitial clay in permeable formations has been discussed by Doll.2,3 Noteworthy papers which dilate further upon the effects of shale and clay on the resistivity of permeable formations are those of deWitte,4,5 Berg,6 Wyllie,7 and most recently, Winsauer and McCardell.8 The last authors have endeavored to elucidate the chemistry of the resistivity phenomena in dirty sands in terms of an adsorption hypothesis. Specifically, they attribute the electrolytic conductivity of shales and clays within a permeable formation to an ionic double-layer effect and, for this reason, regard the term "conductive solids" as a misleading one. Some consideration has been given to the effect of dirty sands on the S.P. by Wyllie7 and by McCardell, Winsauer and Williams." Published work to date has cast light only on certain theoretical aspects of the problems created by the presence of clays and shales within permeable formations. One object of this paper is to describe experiments which serve to elucidate further the theory of the dirty sand problem and particularly the significance of the term "formation factor" as applied to dirty

Jan 1, 1955

By Robert E. Cuthbertson

IT is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson3 by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be confined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. BRIEF HISTORY OF REAGENT PRACTICE AT CLIMAX Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium, cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 1920, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Never theless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1944

By K. A. Gschneidner, O. D. McMasters

DgIel-ential thermal, nretallographic, and X-ray paramzetric methods were used to establish the Yb-Pb phase dingram. The terminal solid solubilities in the system are less than 0.2 at. pct. Lead additions lower the 792°C transformation tewzperature of pure ytterbiun~ at 787°C by means of an inverted peritectic veaction. Ytterbium additions raise the 327oC melting point of lead to 329°C by means of a perilectic reaction. Three intermetallic compounds Yb2Pb, YbPb, and YbPb, melt congruerttly at 1246", 1116o, and 740°C. respectively. YbsPb3 forms by a peritectic reacliorz at 1250°C. YbzPb crystallizes in the PbCh (C23) type structure and the orthorhombic latliceo constants are a, = 7.478. bo = 5.225, aud C0 = 9.549A. YbsPbs crystallizes in the hfnsSi3 (D8a) type structure. The hexa~nal lattice constants for this phase are a, = 9.325 and co = 6.92d. YbPbl crystallizes in the cubic AuCU3 (Ll2) type structure with a: = 4.8628 + 0.0008A. YbPb is diwrorphic with the structure change occurring al 507°C upon healing. The crystal structures of the two forttzs were not determined. Eulectic reactions occur at 5.1 at. pct Pb and 769oC, 41.5 at. pct Pb and 1086oC, and G8.0 at. pct Ph and 717°C: RELIABLE information concerning the alloying behavior of most of the rare-earth metals is scarce. A systematic study of the rare earth-lead alloy systems now in progress is an effort to supply such information. Determination of the phase diagram of the Yb-Pb alloys is the first step of this study. Variations in the valence of normally divalent ytterbium may be studied by comparing the characteristics of the Yb-Pb alloys to those of the trivalent rare earth-lead and of the divalent alkaline-earth-lead systems. Of particular interest are the melting temperatures of the intermetal-lic compounds since these are known to be high relative to the melting points of the constituent metals. Crys-tallographic and magnetic susceptibility data for the rare earth-lead alloys are to be included in the comparative study. Results from this and subsequent investigations should provide a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The major impurities in the ytterbium and lead used in this investigation are listed in Table I. The lead was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The ytterbium was prepared in this laboratory by the lanthanum reduction of the oxide followed by a distillation of the ytterbium. Alloy Preparation. The alloys were prepared by

Jan 1, 1968

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By Richard L. Ash, J. H. Kelley, W. H. McCracken, William Bellano, J. D. Morgan, D. R. Mitchell

Rubber-tired shuttle cars are finding increased use as gathering units in under-ground mines. As the name implies, they shuttle back and forth between the loading machine and the section transportation system. In many mines their use has in-creased the efficiency of the loading and gathering operations, resulting in increased output per man employed and decreased costs per ton. A car motivated by cable reel is shown in Fig I, and a car with battery power in Fig 2. A brief chronological account of the development of rubber-tired haulage equip-ment follows: 1936. J. H. Fletcher1 installed his first unit for the Blue Bird Coal Co., Carrier Mills, Illinois. This unit consisted of a battery-powered industrial tractor and a trailer with drop-bottom doors. The coal was transported for short distances to a hopper for discharge into mine cars. 1938. A battery-powered self-contained shut-tle car with rubber-tired wheels was built by the Joy Manufacturing Co. Two units were installed for the Katherine Coal Co., Lumberport, West Virginia. The shuttle car consisted of a materials-receiving body with a conveyor in the bottom to move the coal forward during loading and to unload the coal at the discharge station. 1938. A cable-powered shuttle car with four-wheel drive and four-wheel steer was developed by A. L. Lee. Special wheels mounted on king pins on the car permitted all four wheels to be steered. The cable reel was driven by a torque motor to give the cable proper tension during the payout and uniform tension when rewound on the reel. 1940. A Joy shuttle car equipped with trolley poles and a cable reel was developed to operate on a double trolley-wire system.2 This unit was installed at a potash mine of the International Minerals and Chemicals Corporation at Carlsbad, New Mexico. It is believed to have been the first installation of its kind, and the first of shuttle cars for handling material other than coal. 1941. Truck haulage3 was introduced in the Tri State District by the Eagle-Picher Mining and Smelting Company. Storage battery electric trucks were rebuilt to handle a bottom-dump trailer. 1941—Joy shuttle cars were installed in a mine of the United States Gypsum Company, Oakfield, New York. 1943—Joy shuttle cars were installed in several bauxite mines.4,5 1945—Joy shuttle cars installed in a lime-stone mine. Because of the nature of bituminous coal beds trackless equipment has had its greatest application in bituminous coal mining. Usually a shuttle car is filled by a continuous type of loader. In Fig 3 is shown a continuous machine loading coal into a battery-powered shuttle car, 48-in. coal. However, intermittent types of load-

Jan 1, 1949

By V. H. Wilhelm

The year 1941 in the California oil industry was marked by an increased market demand, drilling activity, and production of crude oil. Although seven new oil fields and two gas fields were discovered during the year, additions to reserves from these discoveries, as well as extensions and revaluations of previous discoveries, were approximately 100 million barrels, as against estimated withdrawals of 230,233,000 barrels. The year was remarkable for the very great increase in domestic demand for all products, which more than compensated for the loss in shipments to Japan, which averaged 60,041 bbl. Per day during 1940. Demand in terms of crude during 1941 was 648,967 bbl. per day as against 632,647 for the same period in 1940. This abnormal increase in demand is due to increased industrial activity, and especially increased railroad activity. Gasoline consumption for 1941 was 241,011 bbl. per day as against 217,744 in 1940. Demand for fuel oil increased from 259,806 bbl. per day in 1940 to 285,896 in 1941, and caused a withdrawal from stocks of more than 7,473,000 barrels. During 1941, total oil storage declined 9,153,000 bbl., but additions to storage of 1,754,000 bbl. of light oil and light oil products were offset by a withdrawal of 10,907,000 bbl. of heavier products. Production during the year is estimated at 230,233,000 bbl. as against 222,784,386 bbl. for 1940. TraNsportation For a short time, California was affected by lack of transportation due to the diversion of tankers. This shortage affected the movement of oil from the Sari Joaquin mated to the refineries, since a large percentage of this production is moved to the coast through pipe lines, and thence by tankers to Los Angeles and San Fran-,iSco, Return of the tanker fleet, which may be temporary, indicates that there is a possibility of ample supplies of petroleum products in the Pacific Northwest. Drilling Activity Contrary to general opinion, drilling activity increased in 1941 over the pre-vious Year, 942 wells being completed in 1941 as against 890 in 1940, an increase Of 6 per cent. This increase was due to the increased demands for fuel oil, and also to the decreased drilling costs, which made many former marginal locations economic. The main activity caused by increased demands for fuel oil was in the Mt. Poso, McKittrick, Midway and Santa Maria Valley oil fields. Dry-hole footage in 1941 was 655,354 ft. as against 583,537 ft. for 1940. Curtailment Voluntary curtailment succeeded in holding production considerably below demand, although it was above the state quota. During the year the top allotment

Jan 1, 1942

By V. H. Wilhelm

The year 1941 in the California oil industry was marked by an increased market demand, drilling activity, and production of crude oil. Although seven new oil fields and two gas fields were discovered during the year, additions to reserves from these discoveries, as well as extensions and revaluations of previous discoveries, were approximately 100 million barrels, as against estimated withdrawals of 230,233,000 barrels. The year was remarkable for the very great increase in domestic demand for all products, which more than compensated for the loss in shipments to Japan, which averaged 60,041 bbl. Per day during 1940. Demand in terms of crude during 1941 was 648,967 bbl. per day as against 632,647 for the same period in 1940. This abnormal increase in demand is due to increased industrial activity, and especially increased railroad activity. Gasoline consumption for 1941 was 241,011 bbl. per day as against 217,744 in 1940. Demand for fuel oil increased from 259,806 bbl. per day in 1940 to 285,896 in 1941, and caused a withdrawal from stocks of more than 7,473,000 barrels. During 1941, total oil storage declined 9,153,000 bbl., but additions to storage of 1,754,000 bbl. of light oil and light oil products were offset by a withdrawal of 10,907,000 bbl. of heavier products. Production during the year is estimated at 230,233,000 bbl. as against 222,784,386 bbl. for 1940. TraNsportation For a short time, California was affected by lack of transportation due to the diversion of tankers. This shortage affected the movement of oil from the Sari Joaquin mated to the refineries, since a large percentage of this production is moved to the coast through pipe lines, and thence by tankers to Los Angeles and San Fran-,iSco, Return of the tanker fleet, which may be temporary, indicates that there is a possibility of ample supplies of petroleum products in the Pacific Northwest. Drilling Activity Contrary to general opinion, drilling activity increased in 1941 over the pre-vious Year, 942 wells being completed in 1941 as against 890 in 1940, an increase Of 6 per cent. This increase was due to the increased demands for fuel oil, and also to the decreased drilling costs, which made many former marginal locations economic. The main activity caused by increased demands for fuel oil was in the Mt. Poso, McKittrick, Midway and Santa Maria Valley oil fields. Dry-hole footage in 1941 was 655,354 ft. as against 583,537 ft. for 1940. Curtailment Voluntary curtailment succeeded in holding production considerably below demand, although it was above the state quota. During the year the top allotment

Jan 1, 1942

By L. B. Ticknor, M. B. Bever

An isothermal calorimeter suitable for measurements of heats of solution in liquid tin as solvent is described. Measurements of the heats of solution of gold, silver, copper, and a gold-silver alloy are reported. The heat of formation of this gold-silver alloy is also reported. HEATS of solution in liquids can be determined directly, but few such data have been published for metals as solvents. Knowledge of heats of solution is desirable because it contributes to the general understanding of energy relations in metallic solutions. Thermochemical measurements of this type also furnish answers to specific problems: For example, from the heats of solution of an alloy and of a mixture of its constituent elements in a given solvent, the heat of formation of the alloy may be found. Similarly, differences in the energy content of samples of the same metal in two different states, such as the annealed and cold worked states, may be determined. In the work reported here, gold, silver, and an alloy of gold and silver were dissolved in liquid tin at 240°C and gold, silver, and copper were dissolved in tin at 300 °C. The experiments yielded the heats of solution of these metals in tin. The heat of formation of the gold-silver alloy was also determined. The same calorimetric method is being used to measure the energy stored in metals during cold working and preliminary results have been published.' Equipment and Experimental Procedure The isothermal calorimeter used in this work, Fig. 1, consisted of a Dewar flask completely immersed in a constant-temperature salt bath. A long neck provided space for thermocouple leads and a stirrer shaft and permitted the injection of solute samples. The metal bath in the calorimeter flask was stirred at about 100 rpm by a small glass impeller driven by a constant-speed motor. The shaft of the stirrer passed through a Wilson vacuum seal.2 All measurements were made under vacuum in order to eliminate temperature disturbances resulting from gas convection and to prevent the oxidation of tin. The calorimeter flask was joined by an all-glass connecting line to a gas-control system which made possible the use of a protective atmosphere of deoxidized and dried hydrogen. At the operating temperature of the calorimeter tin oxide was not reduced by hydrogen, presumably because the reaction rate was too slow. Part of the closed system was a removable side tube through which the solute sample could be introduced and in which it was held at a temperature of 0°C prior to injection into the metal bath. The salt bath containing a mixture of sodium, lithium, and potassium nitrates was similar to that described by Beattie3 and was equipped with a stir-

Jan 1, 1953

By Arthur Phillips, E. N. Skinner

DURING the course of an experimental program concerned with the hydrogen embrittlement of copper containing oxygen in concentrations within the solubility limits it became necessary to make a critical appraisal of the literature dealing with the solubility relationships of oxygen and solid copper. The latest determinations, and perhaps the only data obtained on "spectroscopically" pure copper, are those of Rhines and Mathewson1 who reported that the solid solubility increases from 0.007 per cent oxygen at 600°C. to about 0.015 per cent at 1050°C. Hanson, Marryat and Ford2 had previously placed the solubility limit at less than 0.009 per cent oxygen at 1000°C. and Allen and Street3 had suggested, on the basis of an unpublished research by T. Hewitt, not over 0.005 per cent oxygen at 500°C. In the introductory stages of the investigation indirect evidence accumulated to suggest that the solubility limits were significantly lower than those previously reported. For this reason it was deemed essential to clarify this point before proceeding with a program intended to establish a quantitative relationship between hydrogen embrittlement and oxygen concentrations positively known to be within the solid solution range. Furthermore, the increasing production and the highly selective applications of the commercial "oxygen-free" coppers inevitably direct attention to the practical necessity for exact knowledge regarding the effects of minute concentrations of the elements ordinarily found in the high-purity coppers now available. Of these elements oxygen occupies a unique position, not only by virtue of its specific effects on copper but more particularly in view of its important reactive tendencies toward the other impurities with which it is associated. Rhines and Mathewson considered several methods for measuring the solubility of oxygen and finally adopted the simple plan of saturating the specimens, obtained from redeposited cathode copper, by heating at the desired temperature in air. After the removal of surface oxide by mechanical and chemical means, the oxygen content was determined in the underlying metal. In general, this process of saturation, with a few modifications, was followed by the present writers. Although the procedure is direct and has obvious advantages, its effectiveness, unfortunately, is reduced by an excessive scaling of the copper, particularly at the higher temperatures. After saturation treatments above 900°C. the writers found that the specimens, necessarily rather thin in the original condition, consisted largely of scale and yielded too little metal for a satisfactory analytical sample. Furthermore, great difficulty was experienced in effecting complete removal of the scale. Needless to say, it is necessary to exercise extraordinary care in the preparation of the surface of the analytical sample in order to eliminate submicroscopic fragments of cuprous oxide which ordinarily are lodged in the crevasses and

Jan 1, 1941

By H. H. Evinger, M. Muskat

A methoD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permea-bility data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should havc significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast. IntroductioN Sufficient laboratory research has been carried out in the last several years on the fundamental features of the flow of heterogeneous fluids through porous media to call for consideration of what can be done with this type of information. It has, of course, already led to a, much clearer general understanding of the mechanics of oil production. However, examples of the quantitative application of the results of such laboratory studies are few in the literature. part of the explanation for this fact lies undoubtedly in the lack of sufficient laboratory data relating to practical fluids and sand systems such as would occur ill actual oil reservoirs. However, unless it can be shown that if such data were obtained quantitative applications could be made, serious doubt may be cast upon the desirability of carrying on further extensive experimental research work on fluid flow. The purpose of this paper is to present one approach to the problem of quantitative application of laboratory data to practical field problems. Because the published results on the basic experiments with three-phase fluid systems in porous media are limited entirely to uncon-solidated sands, the numerical applications made here will not pertain directly to any actual field situation. However, they should serve to illustrate what could be done with fundamental laboratory data if they were extended to cover the field of consolidated sands. From this point of view, it is hoped it will serve to encourage further laboratory research on this problem. The particular application to be treated here relates to the calculation of the productivity factors for oil-gas-water systems in the steady state. This specific problem seems especially appropriate for discussion in view of the recent publication by Johnston1 of the results of produc-

Jan 1, 1942

By M. Muskat, H. H. Evinger

A methoD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permea-bility data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should havc significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast. IntroductioN Sufficient laboratory research has been carried out in the last several years on the fundamental features of the flow of heterogeneous fluids through porous media to call for consideration of what can be done with this type of information. It has, of course, already led to a, much clearer general understanding of the mechanics of oil production. However, examples of the quantitative application of the results of such laboratory studies are few in the literature. part of the explanation for this fact lies undoubtedly in the lack of sufficient laboratory data relating to practical fluids and sand systems such as would occur ill actual oil reservoirs. However, unless it can be shown that if such data were obtained quantitative applications could be made, serious doubt may be cast upon the desirability of carrying on further extensive experimental research work on fluid flow. The purpose of this paper is to present one approach to the problem of quantitative application of laboratory data to practical field problems. Because the published results on the basic experiments with three-phase fluid systems in porous media are limited entirely to uncon-solidated sands, the numerical applications made here will not pertain directly to any actual field situation. However, they should serve to illustrate what could be done with fundamental laboratory data if they were extended to cover the field of consolidated sands. From this point of view, it is hoped it will serve to encourage further laboratory research on this problem. The particular application to be treated here relates to the calculation of the productivity factors for oil-gas-water systems in the steady state. This specific problem seems especially appropriate for discussion in view of the recent publication by Johnston1 of the results of produc-

Jan 1, 1942