Search Documents

By D. R. Conlon, E. R. Brownscombe

Errors in measurement of reservoir pressure include: (I) gauge errors, and (a) interpretation errors. Gauge errors may be reduced by: (a) reading charts with a comparator microscope, (b) use of hard metal stylus points to give clear lines, (6) insuring temperature equilibrium, and (d) making multiple tests. Check calibrations are equally as important as check well tests. A statistical analysis of such check runs shows quantitatively the advantages of a standardized "zero pressure line'' and of the use of field calibrations made at bottom-hole temperature on the same chart run in the well. Interpretation errors include: (a) fluid heads, which should be corrected to the top of the perforations on the basis of well-fluid gravity and from the top of the perforation to the datum level on the basis of reservoir-fluid gravity, and (b) gradients around the well. Conventional shut-in periods may be entirely inadequate to overcome these, necessitating a reservoir study based on build-up curve data, reservoir history, core analysis and any other available information. Interest in engineering studies of the pressure changes in oil and gas reservoirs is increasing. This type of work yields important information and doubtless will be greatly extended in the future. One of the factors limiting the work, however, is the accuracy with which the reservoir pressures can be determined; for if the inaccuracies in the pressure measurements represent an appreciable percentage of the pressure changes, the engineer is seriously handicapped, and must delay the reservoir study until the reservoir pressure has changed a relatively large amount. This delay can greatly reduce the benefits of such studies, at least from the point of view of aiding the leasing, drilling and completion programs. Thus, from the point of view of reservoir analysis, it is frequently important to obtain the most accurate pressure data possible early in the history of any field—particularly for the gas-distillate fields now being developed. This paper deals with improvements in the measurement of bottom-hole pressures that permit pressures even as high as 4000 or 5000 lb. per sq. in. to be determined with gauge errors of only+ ±I to 2 lb. per sq. in. Since pressures out in the reservoir rather than in the bottom of the hole concern the reservoir analyst, differences between bottom-hole pressures and actual reservoir pressures are also considered. In general, errors in pressure measurement may be divided into: 1. Gauge errors: a. Errors due to inaccuracies in reading the pressure charts. b. Errors due to irreproducibility of the pressure element and recording system. c. Errors caused by failure to allow the gauge to reach temperature equilibrium. 2. Internretation errors: a. Errors caused by a fluid head between the gauge position in tubing and the pressure at the datum level in the reservoir. b. Pressure gradients in the reservoir.

Jan 1, 1946

By D. R. Conlon, E. R. Brownscombe

Errors in measurement of reservoir pressure include: (I) gauge errors, and (a) interpretation errors. Gauge errors may be reduced by: (a) reading charts with a comparator microscope, (b) use of hard metal stylus points to give clear lines, (6) insuring temperature equilibrium, and (d) making multiple tests. Check calibrations are equally as important as check well tests. A statistical analysis of such check runs shows quantitatively the advantages of a standardized "zero pressure line'' and of the use of field calibrations made at bottom-hole temperature on the same chart run in the well. Interpretation errors include: (a) fluid heads, which should be corrected to the top of the perforations on the basis of well-fluid gravity and from the top of the perforation to the datum level on the basis of reservoir-fluid gravity, and (b) gradients around the well. Conventional shut-in periods may be entirely inadequate to overcome these, necessitating a reservoir study based on build-up curve data, reservoir history, core analysis and any other available information. Interest in engineering studies of the pressure changes in oil and gas reservoirs is increasing. This type of work yields important information and doubtless will be greatly extended in the future. One of the factors limiting the work, however, is the accuracy with which the reservoir pressures can be determined; for if the inaccuracies in the pressure measurements represent an appreciable percentage of the pressure changes, the engineer is seriously handicapped, and must delay the reservoir study until the reservoir pressure has changed a relatively large amount. This delay can greatly reduce the benefits of such studies, at least from the point of view of aiding the leasing, drilling and completion programs. Thus, from the point of view of reservoir analysis, it is frequently important to obtain the most accurate pressure data possible early in the history of any field—particularly for the gas-distillate fields now being developed. This paper deals with improvements in the measurement of bottom-hole pressures that permit pressures even as high as 4000 or 5000 lb. per sq. in. to be determined with gauge errors of only+ ±I to 2 lb. per sq. in. Since pressures out in the reservoir rather than in the bottom of the hole concern the reservoir analyst, differences between bottom-hole pressures and actual reservoir pressures are also considered. In general, errors in pressure measurement may be divided into: 1. Gauge errors: a. Errors due to inaccuracies in reading the pressure charts. b. Errors due to irreproducibility of the pressure element and recording system. c. Errors caused by failure to allow the gauge to reach temperature equilibrium. 2. Internretation errors: a. Errors caused by a fluid head between the gauge position in tubing and the pressure at the datum level in the reservoir. b. Pressure gradients in the reservoir.

Jan 1, 1946

By J. W. Hickman

INTRODUCTION MOST of the electron diffraction studies of oxide films which form on metals and alloys have been carried out by oxidizing the specimens in an auxiliary furnace, cooling down to room temperature and then inserting the sample in the camera and taking a diffraction photograph. Prior to the investigations at the Westinghouse Research Laboratories, no systematic study of the oxidation of any metal or alloy had been made over a wide temperature range with photographs taken at elevated temperatures except the investigation of iron by Jackson and Quarrell.1 In order to interpret the electron diffraction patterns of the oxides which may form on alloys, it seemed advisable to make a comprehensive study of the oxidation of the purest metals available in the bulk form. Thus far studies have been completed on iron,2 cobalt,2 nickel,2 chromium ,2 Copper2, tungsten,3 molybdenum,3 beryllium ,4 uranium,4 thorium4 titanium5 and zirconium5 while investigations are in progress on tantalum and columbium, The next step in the study is concerned with the investigation of the oxides which form on binary alloys. Some of the alloys consist of a single, phase while others contain more than one phase. The identification of the oxides on the surface of a binary alloy may be more difficult than on the metals since oxides containing both metals as well as those of each metal separately may form. Furthermore, it is possible that solid solutions of the various oxides may occur. In these cases the electron diffraction method may not be able to identify the oxidation products unequivocally, Examples of solid solutions which may present difficulties are MoO2 and W02, Fe3O4 and FeO-Cr2O3 since the diffraction patterns are so similar. Since electron diffraction can determine only the structure of the oxide, the chemical composition must be inferred from the diffraction data based upon X ray diffraction investigations of specimens of known composition. It is possible in some cases to decide whether a given solid phase reaction can occur on the surface of an alloy by a study of available thermodynamic data. Table I lists the equations for the formation of most of the oxides from the elements together with values of log10 KR for the several temperatures. [OF°R = -RT In KR 0 and-~75T = logi°KR] [?F°R] and KR are the free energy and equilibrium constant of the reaction. Calculations may be made using the values given in Table I to determine whether a given solid phase reaction is possible thermodynamically. For example, a solid phase reaction should occur between aluminum and chromium' oxide to form

Jan 1, 1948

By R. L. Featherly, J. R. James

The replacement or reconditioning of oil storage tank bottoms due to external corrosion is an expensive maintenance item to the oil industry. Cathodic protection as a means of mitigating this problem has proved very successful in the past few years. One pipe-line company recently used magnesium anodes to cathodically protect two 55,000 bbl and two 20,000 bbl tanks. The tank bottoms were protected as individual units with considerable factual data being taken on one of the 20,000 bbl tanks. Twelve 60-lb anodes were installed about 2½ ft from the tank on approximately 17-½ft centers around the tank. Previous installations and tests have shown that sufficient protection is provided when the tank-to-soil potential using a copper-copper sulphate half-cell as a reference electrode is — 0.90 volts at the edge of tank. Potential measurements taken a few months after completing the installation indicated that the potentials were higher than were needed for protection. Resistors were then inserted in the individual anode circuits which increased the life of the anode installation and still provided adequate protection for the structure. All connecting pipe lines were then insulated from the tank. This limited the anode current strictly to the tank resulting in a greater degree of protection with a still longer anticipated anode installation life. The total installation cost for this tank was less than $300 which amounts to $20 per year The corrosion of metallic structures in contact with soil or water has been a very serious and costly problem for centuries. The annual loss to our nation's pipelines alone is estimated at $200,000,000. Mitigation of this problem by various methods has been carried on quite successfully for a number of years. An electrical method called cathodic protection has been used with considerable success to control corrosive influences on pipelines, tank bottoms, cable sheathing and other buried metal structures. Corrosion of oil storage tank bottoms has been a serious problem among the oil industries for years. In addition to damage costs and loss of oil, the replacement of one tank alone represents several thousand dollars. A reconditioning program at periodic intervals was instituted by several organizations and found to be a very expensive process. A few years ago two of the pipeline companies installed cathodic protection units at their tank farms.3'4 The average current required for protection of the tank bottoms varied from 0.7 to 1.0 milliampere per square foot. The results indicated that adequate protection was obtained at a cost of approximately 10 pct of the previous reconditioning program. The Republic Pipe Line Company experienced severe corrosion on their oil storage tanks. One of their 55,000-bbl tanks

Jan 1, 1948

By R. L. Featherly, J. R. James

The replacement or reconditioning of oil storage tank bottoms due to external corrosion is an expensive maintenance item to the oil industry. Cathodic protection as a means of mitigating this problem has proved very successful in the past few years. One pipe-line company recently used magnesium anodes to cathodically protect two 55,000 bbl and two 20,000 bbl tanks. The tank bottoms were protected as individual units with considerable factual data being taken on one of the 20,000 bbl tanks. Twelve 60-lb anodes were installed about 2½ ft from the tank on approximately 17-½ft centers around the tank. Previous installations and tests have shown that sufficient protection is provided when the tank-to-soil potential using a copper-copper sulphate half-cell as a reference electrode is — 0.90 volts at the edge of tank. Potential measurements taken a few months after completing the installation indicated that the potentials were higher than were needed for protection. Resistors were then inserted in the individual anode circuits which increased the life of the anode installation and still provided adequate protection for the structure. All connecting pipe lines were then insulated from the tank. This limited the anode current strictly to the tank resulting in a greater degree of protection with a still longer anticipated anode installation life. The total installation cost for this tank was less than $300 which amounts to $20 per year The corrosion of metallic structures in contact with soil or water has been a very serious and costly problem for centuries. The annual loss to our nation's pipelines alone is estimated at $200,000,000. Mitigation of this problem by various methods has been carried on quite successfully for a number of years. An electrical method called cathodic protection has been used with considerable success to control corrosive influences on pipelines, tank bottoms, cable sheathing and other buried metal structures. Corrosion of oil storage tank bottoms has been a serious problem among the oil industries for years. In addition to damage costs and loss of oil, the replacement of one tank alone represents several thousand dollars. A reconditioning program at periodic intervals was instituted by several organizations and found to be a very expensive process. A few years ago two of the pipeline companies installed cathodic protection units at their tank farms.3'4 The average current required for protection of the tank bottoms varied from 0.7 to 1.0 milliampere per square foot. The results indicated that adequate protection was obtained at a cost of approximately 10 pct of the previous reconditioning program. The Republic Pipe Line Company experienced severe corrosion on their oil storage tanks. One of their 55,000-bbl tanks

Jan 1, 1948

By M. W. Dumais, E. P. Abrahamson

In a paper by Abrahamson and Alexander concerning a series of correlations between electronic structure and property changes, it was hypothesized that each solute atom in a dilute solution had a characteristic volume of solvent atoms over which some form of electronic interaction occurred. From this description it is possible to picture the solute atoms as occurring in an ordered array for the most efficient arrangement. A recent review article2 has shown that some form of anomaly exists for a whole series of properties when dilute additions of tungsten are made to iron, of. Fig. 1. Any mechanism to fit one property must also be amenable to mechanisms for the other properties. The possibility of some structural change in this region appears to offer the best hope. The system chosen for investigation was the iron tungsten system. Zone-refined iron with zone-leveled tungsten additions were supplied by Materials Research Corp. as 3/8-in.-diam bars. Transmission electron microscopy was used to study the structure. One-quarter inch specimens of each alloy were cold-rolled to 10-mil sheets, cleaned, punched to electron-microscope specimen-holder size, and annealed in vacuum for 2 hr at 800°C and 2 hr at 700°C followed by a furnace cool. The specimens were attached to a platinum wire and the specimen edge and wire were painted prior to thinning in a solution of 10 pct perchloric acid in glacial acetic acid. It was believed that if ordering were present due to electronic interactions the polishing procedure chosen would provide a simultaneous combination of chemical attack and electropolishing to exhibit the ordered structure. The chemical attack would be expected to penetrate those areas equidistant from the tungsten atoms, while the electropolishing would serve to "plane off" the volumes where the chemical attack had taken place. If one of the ordered tungsten planes were parallel to the specimen face at the edge of the thinned hole, a plate or micalike structure would be expected. A typical result of this polishing is shown in Fig. 2. Here a series of plates can be seen lying one upon the other. In several other specimens the plates parallel to the electron beam have been observed, behaving like slices of bread in a loaf. These edge views coupled with moire patterns indicate that the minimum plate thickness is 37 to 42A. This is equivalent to a concentration of 455 at. ppm of W if a simple cubic superlat-tice exists, or one tungsten atom every twelve iron atoms on the ordered plane. It was further noted that the base iron exhibited no signs of platelike structure. As the concentrations increased above 100 at. ppm W the amount of plate material increased. Among the specimens investigated was that shown

Jan 1, 1967

By R. P. Carreker, J. G. Leschen, J. H. Hollomon

The external appearance of a crystal which has undergone plastic flow suggests that adjacent blocks of the crystal have glided bodily past one another along the slip planes. However, the great discrepancy between the shear stresses calculated to effect such a movement and those actually observed has for many years stimulated searches for more satisfactory interpretations of the slip process. Appreciable success in these efforts has been realized by assuming the presence in the crystal of various sorts of imperfections and by considering the consequences of the presence of these flaws when stress is externally applied. The theory that has received the most attention recently—that of dislocations—postulates the occurrence of small, mobile imperfections or dislocations which move through the crystal along the slip direction, each dislocation being attended by a local shear displacement of one interatomic distance. Thus only that portion of the crystal through which the dislocation has passed may be said to have slipped. Since each dislocation produces a displacement of only one interatomic distance, an avalanche or train of many dislocations would be necessary to account for the observed displacements of several hundred or thousand interatomic distances. The salient point of the theory of dislocations is the concept that a slip band does not suddenly appear in its entirety. On the contrary, it grows progressively across the slip plane as the individual dislocations successively appear and advance in a train through the crystal. However, the concept of growth is not intrinsic only to the theory of dislocations, since atomistic mechanisms other than that postulated by the dislocation theory can quite probably also describe the growth of a slip band. For instance, a slip band might resemble a disc-like interface that appeared and then grew continuously from a small size, producing a displacement that increased with the size of the disc. Whatever the precise mechanism, the concept of growth is in itself consistent both with the observed low values of critical shear stress and with the experimental observation that slip bands frequently do not traverse the entire crystal. The likelihood that slip bands grow implies that they must first be nucleated and that the initiation of slip can therefore be analyzed in terms of the general concepts of nucleation. Indeed, this suggestion was advanced1 several years ago, but the matter does not appear to have been further pursued. Recent advances in the theory of nucleation 2,3,4 have encouraged such a treatment of the slip process. As will presently be demonstrated, this approach to the problem not only accounts successfully for the incubation periods that have been observed 5,6 to precede slip but also predicts certain transient effects in the deformation process. The existence of these transients apparently has not hitherto

Jan 1, 1949

By J. P. Newell, R. W Storey

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120". This head design proved to be very satis-

Jan 1, 1953

By R. H. Smith, A. C. Polk

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By J. P. Newell, R. W. Storey

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120". This head design proved to be very satis-

Jan 1, 1953

By A. C. Polk, R. H. Smith

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By I. D. Shah

A roasting procedure for synthetic copper sulfide which results in a reproducible transient melting at 450° and 470°C is described in this paper. Possible causes for this melting phenomenon are suggested, and also a procedure to avoid it during the roasting. This melting is believed to be responsible for the occasional occurrence of stickiness in the commercial roasting of copper sulfide concentrate. Many workers have studied the roasting of copper sulfides, but only Lewis et al. have reported that fusion and, in some cases, fusion with "boiling" occurred in the neighborhood of 450°C. The DTA and TGA apparatus, the materials used in this investigation, and the discussion of chemical reactions occurring during the CuS roasting are described in an earlier publication. CuS, in the form of either pellet or powder, was heated at 280° to 330°C in a flowing air or 30% 02: 70% N2 atmosphere. Heating was continued at this temperature until no further weight increase due to sulfates formation was observed on the TGA thermogram. This is believed to be due to the inability of SO, to diffuse out from the sulfate layer on the surface of the pellet, thus halting the sulfate-forming reactions. Hereafter, the sample oxidized in this manner will be referred to as "partially oxidized CuS." X-ray analysis and microscopic examination of a polished cross section of a partially oxidized CuS pellet showed the following order of layers starting from the center of the pellet: Cu2S, Cu2O, CuO • CUSO4, and CuSO4. A bare thermocouple inserted in the center of a partially oxidized CuS pellet (2.5 g) did not indicate any noticeable change in the temperature of the pellet when melted at 450° to 470°C in an inert or oxidizing atmosphere. During the preparation of a partially oxidized pellet, the temperature of a CuS pellet increased by 50°C due to the exothermic formation of sulfates in air at 320°C. The endothermic peak associated with the melting phenomenon at 450°C is shown in [Fig. 1.] A CuS pellet (0.2 g) was oxidized in flowing air (150 cc per min) at 10°C per min up to 320°C and held there for about 2 hr. Then, N2 replaced air and heating was continued up to 500°C. The exothermic peak at 320°C represents an overall formation of sulfates, and an endothermic peak at 450° to 470°C represents the melting phenomenon. To observe the melting visually, a small (50 mg), partially oxidized CuS pellet was heated (in static air) in a hot-stage microscope. The melting phenomenon was observed on an auxiliary TV screen. The sample

Jan 1, 1976

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By E. I. Larsen

Powder metallurgy has been described as being "as old as the pyramids and yet as new as the latest bomber." While this may be true literally, it has been only in the last Io or 1 5 years that widespread use has been made of this method of fabricating various articles One of the first items fabricated by powder metallurgical methods on a commercial scale was electrical contacts, which were fabricated from metal powders as early as 1920. The reason why these contacts have been made for so many years by powder metallurgy is because the compositions of most of these materials arc such that they could not be made by the conventional methods of melting, casting, rolling, drawing, etc. Classes of Contacts In general, electrical contacts fabricated from metal powders fall into two classes, both from the point of view of the method of fabrication and the components that make up the chemical composition. One class is composed of silver or copper and a refractory metal such as tungsten, molybdenum, or compounds thereof such as carbides. The second class contains a predominant amount of silver and a semi-refractory material such as cadmium oxide, nickel, cobalt, or graphite. Electrical contacts of the first class have been developed primarily as facing materials for heavy-duty circuit-interrupting devices. This class of material unites the high melting point, high boiling point, great resistance to electrical erosion, and the refractory characteristics of molybdenum, tungsten, or their carbides with the high thermal and electrical conductivities and low contact resistance properties of silver or copper. The second class of material is used for lighter duty or specialized applications such as heavy-duty, direct-current aircraft relays. Varieties Electrical contacts fabricated from metal powders are made in a wide variety of compositions, shapes, and sizes. In general, the sizes of electrical contacts fabricated from powders vary from contacts weighing approximately 0.001 oz. up to those weighing 3 to 4 Ib., the contacting face being as small as 0.001 sq. in. up to approximately 6 sq. in. in area. The shapes consist of: sound or rectangular buttons, some of which have radii or bevels on the contacting faces; rings, cups, rectangular bars, the contact face of which may have a radius across the width and/or at one end; and form-pressed pieces of a wide variety such as angles, both acute and obtuse, irregular shapes comprising a radius blended into a flat, which in turn may have steps. The size or shape of the contact is dictated principally by the mechanical design of the manufacturer, who in turn may have problems to be met such as: (I) size, weight, or space limitations; (2) electrical conditions such as blowout coils arc chutes, baffies, gas passages.

Jan 1, 1945

By Shiou-Chuan Sun

There are several postulations for the mechanism of slime-coating. Incel proposed the electrostatic hypothesis, del Giudice2 suggested the chemical theory; Bankoff3 reported that slime-coating is inhibited whenever the surfaces of the slime particles are ionized sufficiently for Brownian movement to occur, and is facilitated when they are not. These postulations were examined by experiments involving the Burton tube, the cataphoretic cell, and slime-coating. The techniques involved will be described elsewhere in this paper. The electrostatic hypothesis, supported by migration experiments in a Burton tube, was abandoned by del Giudice.2 Experiments of mineral migration in a Burton tube. after the idea of Ince with modification, indicated that this apparatus was inefficient for accurate observation. A cataphoretic cell was constructed. The experimental data, as shown in this paper, enable the correlation and advancing of this hypothesis. Del Giudice's chemical hypothesis considered that slime particles are attached to the galena surfaces by a cement formed as the result of a metathetical reaction between the sulphide and the slime particles. Applying this hypothesis, the calcite slime particles were cemented to the galena surface by the formation of a cementing lead carbonate. In a similar way, lead silicate was considered as the cement of quartz slime coating on galena. Experiments verifying this hypothesis were carried out according to the following procedure: Fresh mineral particles selected from the central part of the broken lumps and examined first under a microscope for ascertaining a clean surface were placed in a small beaker (1.5-in. dia. by 2.5 in. deep) half filled with one kind of slime pulp. The dilution of all slime pulp was 4:I and the particle size of slime was minus 400-mesh. After agitation for 5 min. the specimen was removed by a sharp-end tong and washed gently three times in three separate distilled water baths. It was dried before a small electrical fan and examined immediately under a microscope. A photograph was made of the observation. With reference to the published solubilities,' several of these experiments, which contradict the chemical hypothesis, are listed as following: I. The coating of fluorite slime on the galena surface was light but the coating of galena slime on the fluorite surface was heavy. In a similar way, the coating of quartz slime on the galena was fairly light, but the coating of galena slime on the quartz particle was heavy. According to the chemical hypothesis, using the same constituents and regardless of which is the slime, the density of the coating should be expected to be the same. This, however, as shown above, is not true. Moreover, fluorite (CaF2), having a solubility of 16 mg.4a per liter of water, should not be

Jan 1, 1943

By Shiou-Chuan Sun

There are several postulations for the mechanism of slime-coating. Incel proposed the electrostatic hypothesis, del Giudice2 suggested the chemical theory; Bankoff3 reported that slime-coating is inhibited whenever the surfaces of the slime particles are ionized sufficiently for Brownian movement to occur, and is facilitated when they are not. These postulations were examined by experiments involving the Burton tube, the cataphoretic cell, and slime-coating. The techniques involved will be described elsewhere in this paper. The electrostatic hypothesis, supported by migration experiments in a Burton tube, was abandoned by del Giudice.2 Experiments of mineral migration in a Burton tube. after the idea of Ince with modification, indicated that this apparatus was inefficient for accurate observation. A cataphoretic cell was constructed. The experimental data, as shown in this paper, enable the correlation and advancing of this hypothesis. Del Giudice's chemical hypothesis considered that slime particles are attached to the galena surfaces by a cement formed as the result of a metathetical reaction between the sulphide and the slime particles. Applying this hypothesis, the calcite slime particles were cemented to the galena surface by the formation of a cementing lead carbonate. In a similar way, lead silicate was considered as the cement of quartz slime coating on galena. Experiments verifying this hypothesis were carried out according to the following procedure: Fresh mineral particles selected from the central part of the broken lumps and examined first under a microscope for ascertaining a clean surface were placed in a small beaker (1.5-in. dia. by 2.5 in. deep) half filled with one kind of slime pulp. The dilution of all slime pulp was 4:I and the particle size of slime was minus 400-mesh. After agitation for 5 min. the specimen was removed by a sharp-end tong and washed gently three times in three separate distilled water baths. It was dried before a small electrical fan and examined immediately under a microscope. A photograph was made of the observation. With reference to the published solubilities,' several of these experiments, which contradict the chemical hypothesis, are listed as following: I. The coating of fluorite slime on the galena surface was light but the coating of galena slime on the fluorite surface was heavy. In a similar way, the coating of quartz slime on the galena was fairly light, but the coating of galena slime on the quartz particle was heavy. According to the chemical hypothesis, using the same constituents and regardless of which is the slime, the density of the coating should be expected to be the same. This, however, as shown above, is not true. Moreover, fluorite (CaF2), having a solubility of 16 mg.4a per liter of water, should not be

Jan 1, 1943

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By H. W. Straley

Some ten years ago the writer1 made a survey of college catalogues to determine what sort of training geologists were receiving in basic sciences. In the light of this compilation and subsequent experience, he made the statement at the 1939 meeting of the Institute that apparently only in schools offering a curriculum in geological engineering or in the geological option of mining engineering curricula could geologists hope to receive the training advocated by Hubbeet.2 In the former study, schools of engineering were excluded because the preparation was known beforehand. The present study aims to consider engineering schools in an effort to determine not only what basic studies are required but what use is made of them in geological courses of the third and fourth years. The present study combined the method of consulting catalogues with a questionnaire. Letters were mailed to officials responsible for supervision of mineral industries curricula requesting information On' (I) the extent to which the engineering preparation of the first two years is actually used in the work of the last two; (2) the extent to which the engineering of the last two years is used in courses in geological engineering or geology; and (3) whether geologists or geological engineers teach descriptively or analytically. Both methods of securing information are open to criticism; the former on the basis of the incomplete information supplied by university catalogues concerning prerequisites and curricula and the latter on the ground that the questions may be phrased poorly or given insufficient consideration by replying officials. Fifty-six questionnaires were mailed and 39 (70 per cent) replies were received. Of the replies, 6 (11.3 per cent) were from colleges of liberal arts unconnected with engineering schools, 11 (20 per cent) were from schools having curricula in geological engineering and 22 (39 per cent) were from departments of mining engineering. The number of replies and their distribution were satisfactory in spite of the receipt of only six from liberal arts colleges. It should be understood that the universities of which the catalogues were examined were not necessarily the same in both compilations. No departments that are admittedly or known to be acting solely as service departments were recorded in the second study. Table I shows that all professional schools require mathematics through calculus, whereas only 7 per cent of the liberal arts curricula expect the same level of preparation; only 73 per cent require trigonometry and 40 per cent college "algebra. The proportion of geological engineering curricula requiring differential equations is higher than mining. All of the engineering schools require general and analytical chemistry, whereas only 77 per cent of liberal arts curricula require general and 18 per cent analytical. Twenty-two per cent of the mining and 40 per cent of the geological engineering

Jan 1, 1946

By H. W. III Straley

SOME ten years ago the writer1 made a survey of college catalogues to determine what sort of training geologists were receiving in basic sciences. In the light of this compilation and subsequent experience, he made the statement at the 1939 meeting of the Institute that apparently only in schools offering a curriculum in geological engineering or in the geological option of mining engineering curricula could geologists hope to receive the training advocated by Hubbert.2 In the former study, schools of engineering were excluded because the preparation was known beforehand. The present study aims to consider engineering schools in an effort to determine not only what basic studies are required but what use is made of them in geological courses of the third and fourth years. The present study combined the method of consulting catalogues with a questionnaire. Letters were mailed to officials responsible for supervision of mineral industries curricula requesting information on: (I) the extent to which the engineering preparation of the first two years is actually used in the work of the last two; (2) the extent to which the engineering of the last two years is used in courses in geological engineering or geology; and (3) whether geologists or geological engineers teach descriptively or analytically. Both methods of securing information are open to criticism; the former on the basis of the incomplete information supplied by university catalogues concerning prerequisites and curricula and the latter on the ground that the questions may be phrased poorly or given insufficient consideration by replying officials. Fifty-six questionnaires were mailed and 39 (70 per cent) replies were received. Of the replies, 6 (11.3 per cent) were from colleges of liberal arts unconnected with engineering schools, 11 (20 per cent) were from schools having curricula in geological engineering and 22 (39 per cent) were from departments of mining engineering. The number of replies and their distribution were satisfactory in spite of the receipt of only six from liberal arts colleges. It should be understood that the universities of which the catalogues were examined were not necessarily the same in both compilations. No departments that are admittedly or known to be acting solely as service departments were recorded in the second study. Table I shows that all professional schools require mathematics through calculus, whereas only 7 per cent of the liberal arts curricula expect the same level of preparation; only 73 per cent require trigonometry and 40 per cent college algebra. The proportion of geological engineering curricula requiring differential equations is higher than mining. All of the engineering schools require general and analytical chemistry, whereas only 77 per cent of liberal arts curricula require general and 18 per cent analytical. Twenty-two per cent of the mining and 40 per cent of the geological engineering

Jan 1, 1941