Search Documents

By G. B. Pryde

IN laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the raise and rooms turned at right angles to said entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut in rooms, and entry and room crosscuts should be driven on sights; room crosscuts should be driven at right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire.

Jan 2, 1921

By Ernest Robinson

SINCE the early nineties, there has been a persistent belief in some minds that petroleum in commercial quantities exists in Montana. It is, however, only comparatively recently that commercial produc-tion has been secured. . The earliest deep boring in the plains region of Montana was made in what is now Blaine County, in 1890, by the town of Chinook in an effort to secure artesian water. The well reached a depth of 956 ft. without developing an adequate supply of fresh water, but the drillers reported shows of oil and gas. In 1892, the Quartermaster's Depart-ment of the U. S. Army drilled a hole at Fort Assini-boine, northwest of the Bearpaw Mountains, in essentially flat-lying sediments to secure water for the military establishment. This well reached a depth of 1500 ft. and shows of oil and gas were reported. In 1903 and 1904, two wells were drilled within what is now the Glacier National Park in an effort to develop oil production. Shows of oil and gas were encountered at several horizons but no commercial production was brought in. The extraordinary geological conditions in the area where these wells were drilled should be mentioned. The thrusts from the southwest which, in other places along the Rocky Mountain front, resulted in folding, here developed the great Lewis overthrust fault. It is in fact largely to this fault that the magnificent scenery of the Glacier Park is due. A great thickness of Algonkian strata belonging to the Belt series was thrust northeastward over the upper Cretaceous sediments. The derricks under which the wells referred to were drilled were in moun-tains composed of very old rocks but the holes were drilled through Cretaceous sediments.

Jan 7, 1923

By W. S. Gresley

The object of this communication is to give a description of some remarkable spheroidal specimens of anthracite coal recently encountered in stripping the Mammoth seam at Milnesville, Luzerne county, Pa. Somewhat similar forms of coal, occurring in France and in Australia, have been described already. In vol. xxxvii. (1888) of the Transactions of the North of England Institute of Mining and Mechanical Engineers, under the title "Coal Nodules from the Borehole Seam at Newcastle, New South Wales," Mr. T. E. Forster describes and illustrates, with two plates of specimens, a series of " nodular " forms of anthracite coal taken from a depth of 300 feet beneath the town of Newcastle, and possessing the following characteristics : The lines of cleavage of the coal-seam are more or less curved, giving a rouuded appearance to the blocks. Dikes of intrusive dolerite intersect the coal, and the coal-nodules occur with with greatest frequency where the seam is most disturbed. They are easily separated from the surrounding coal. "The seam at this point is remarkable, not only for its splendid proportions but also for its extremely bright and rich appearance, which gives the working-places x strong resemblance to those in the Pennsylvania anthracite mines.....The cleavage of the coal is, in some park of the pit, noticeable for a series of small impressions or concavities about the size of, and resembling roughly in shape, a mussel-shell raised vertically on its longest edge.....To some extent the nodules appear to have a more or less concretionary structure, and to be, roughly speaking, composed of several concentric layers, through which the ordinary cleavage of the coal passes, while in others thin layers may be observed, resembling the coats of an onion!' The chemical composition of one of the nodules, as well as of the seam inclosing them, is as follows:

Jan 1, 1893

By C. B. Murray

"OUR experience from time immemorial has been that the furnace sampler and analyst usually find one or two, and sometimes more, points less iron than the Lake Superior shippers, but, fortunately, their contracts are `iron bound'; and, generally speaking, analyses at this end are practically useless, for we are obliged to settle on basis figured out to a half dozen decimals, and, as a rule, without recourse in the event of flagrant discrepancies between the two analysts." The above is an extract from a letter received by the writer of this paper from the President of an iron company, discussing the question of sampling. It so well expresses the opinion of many blast-furnace owners and managers that it seems a suitable text for a discussion concerning the need of uniform methods of sampling. If all railroad cars were loaded the same, if all stock piles were the same shape, and if ore was received regularly each day, the problem of sampling would be comparatively simple. The conditions, however, vary widely at different places, and at the same place from day to day, and it is probably impossible to determine upon any one method of sampling which will apply at all times and in all cases. However, it would seem as though some general principles might be suggested which would tend to overcome these wide differences in samples of the same thing. The sampling of a cargo of iron ore begins at the breast of ore in the mine. The ore is sampled from the mine cars, from the stock piles, and from the railroad cars at the mines. At the lower Lake ports the ore is practically all sampled from the boat, occasionally from railroad cars. At the furnaces, the ore is nearly all sampled from railroad cars and occasionally from stock piles.

Jan 1, 1914

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By Woolsey McA. Johnson

In metallurgical circles it is known widely, but somewhat vaguely, that the ease of reduction of metallic oxides depends largely on the way they hare been prepared. It is likewise known that different forms of carbon have different and greatly varying reducing powers. It is the purpose of this paper to show somewhat more definitely and scientifically these facts. Some years ago the writer published an account of pyrometric determinations of the reduction temperature of zinc oxides variously prepared and of several kinds.' In said paper it was shown that the temperature at which zinc oxide evolves zinc according to the equa-tion ZnO + C = Zn + CO depends upon the nature of the two reacting bodies. The determina-tions had a range of accuracy of from 2° to 6°C., whereas differences were found to amount to an extreme of 90' C. So the differences are real ones and must have a definite cause. The equation of boiling water, (H2O)4 D 4 (H2O) has a fixed temperature for equilibrium of 100° C. at 760 mm. pressure. In general, all equations reacting in the liquid or the gaseous phase have well-defined constant physical conditions which govern the equilibrium point and reaction velocities. In a reaction where we have one or more solid phases, the tempera ture conditions requisite for the unbalancing of the stable system are found to vary. These variations are due to the fact that in a solid there is a very complex molecule and it is not a question solely of the tearing away of two interlocked atoms, but also of the destruction of a complex molecule containing hundreds, or possibly thousands, of smaller molecules. In other words, there are two forces to be overcome: a certain

Jan 1, 1914

By Will Coghill

FLOTATION has been so closely allied with the sulfide minerals and their early and associated oily reagents that the term "oil flotation" has erroneously been applied to the entire flotation process. Today, the term "chemical flotation" might be used to advantage. Flotation literature has dealt primarily with the removal of sulfides from non-sulfide gangues, and the separation of one sulfide from another. Now, the application of the process to the separation of nonsulfide minerals is coming to the fore; and from the standpoint of the number of commercial minerals involved, the flotation of nonsulfides offers the larger field. Here, soap or soap-forming substances, such as the fatty acids and their derivatives, are used; hence there may well be a subdivision of the chemical flotation process called "soap flotation." Early experimenters learned that it was easy to form a froth or foam that would carry a part or all of the ore charge over the lip of the flotation machine; but this could not be regarded as flotation because of the lack of selectivity. Doubtless soap was one of the first reagents tried, and doubtless it was rejected on account of its gangue-carrying properties. Now this same gangue-carrying ability makes soap an acceptable reagent, for we are dealing with that, which among sulfides, is considered "gan-gue." As in the flotation of sulfides, so in the flotation of nonsulfides, the selective flocculation of the mineral and the dispersion of the gangue are the first objectives. In fact, these two phenomena epitomize flotation. They depend upon the unlike surface properties of the respective miner-als; and as long as the components of an ore have unlike surface proper-ties, a separation is possible, at least in theory. Often in nonsulfide flotation it makes little difference which mineral floats and which is depressed; generally only a separation is sought.

Jan 1, 1932

RESEMBLING in some respects the enterprise at R Chuquicamata is that of the New Cornelia Copper Co. at Ajo, Arizona. Controlled from its inception by the Calumet & Arizona Mining Co., New Cornelia became a unit of the Phelps Dodge Corporation when the latter absorbed the Calumet & Arizona company in 1931. Both Ajo and Chuquicamata are situated in low mountains in extremely arid desert country. Both ore deposits consisted-the past tense is used advisedly because the oxidized ore has nearly all been mined at Ajo-of a horizon of leachable oxidized ores overlying sulphide or concentrating ore. The principal technical problem in each case was the development of a method for treating the oxidized ore. In both instances the capping of waste rock was comparatively thin and power-shovel mining in open cuts was the obvious method of exploitation. Nature had smiled on neither place in the matter of climate. Though Ajo does not have the persistent winds for which Chuquicamata is notorious, the comforts of living are largely artificial. And it is only fair to emphasize that at each place the mining companies have achieved remarkable success in providing these comforts. Of course, in point of size New Cornelia must be content with the inferior role. From May, 1917, when production was started, to the middle of June, 1930, the company leached 16,368,000 tons of oxidized ore, thereby virtually exhausting the ores of this class. Up to the same date, about 15,000,000 tons of sulphide ore had been mined, and a rough estimate gives 170,000,000 tons remaining in reserve. The total tonnage does not loom very large in comparison with Chuquicamata's billion tons; but it is exceeded by similar figures for only four of the Porphyry group.

Jan 1, 1933

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By H. Shaw

IT is now generally recognized that the gravitational method of geophysical surveying is a valuable aid in elucidating the geological structure of the subsoil and enables the practical geologist to deduce the presence of useful deposits. The particular suitability of the torsion balance to the location of large and important subterranean structures has given rise to a wide application of this method by many of the important oil companies in their search for future supplies, and so intense have been these efforts that little has been heard of the method in other connections, with the exception of occasional references to its application in the location of hidden deposits of metallic ores, salt and lignite, and a number of accounts of its use in the elucidation of geological structures. Its success in the location of salt domes is well known, and establishes it as one of the most important of the geophysical methods, especially for the indirect location of oil. In the British Isles, however, no large occurrence of oil is likely to be revealed, and here the practical application of the gravitational method has been restricted almost entirely to the search for ores. This type of survey possesses well marked characteristics, and presents a gravitational problem that has necessitated the development of a special and probably unusual plan of campaign, full details of which it is hoped will shortly be published. The problems and difficulties encountered in this work are of necessity fundamentally related to those met with in the search for oil by means of the torsion balance, but they also possess several special and distinctive features which undoubtedly differentiate them from the obstacles confronting the oil prospector, and which call for special consideration and treatment.

Jan 1, 1928

By Lillian Erskine

WHILE brass and other copper alloys have long been listed as offering health hazards to their workers, it is questionable if the metals involved are alone responsible for the trades' records of morbidity. The entire science of foundry sanitation is the product of the past two decades; and the best standards now operative would have been regarded as little short of revolutionary prior to 1910. The special handicap to the conservation of the health of the brass founder's employees has been the fact that, unlike the iron founder, his business could be profitably carried on in almost any small and unsanitary quarters. As a result, writers on occupational disease have accepted brass chills or brass founders' ague as an inevitable feature of the trade; and respiratory disabilities, as well as phthisis and disturbances of the nervous system, are also included as prevalent among those employed. While there can be no question as to the basic accuracy of past investigations, there is every reason to doubt the necessity for an undue percentage of ill health among brass molders and casters who are safeguarded by scientific ventilating standards and by improving personal habits of sobriety. There is, however, need for a campaign of education as to the most approved practices and equipment whereby the employer may safeguard the health of his workers, and thereby reduce his labor turnover and increase his productive efficiency. Broadly speaking, copper, tin, and aluminum carry negligible health hazards. The toxic qualities of lead, however, are a menace; especially if scrap lead is recovered or bought for foundry processes. The rapid volatilization of zinc renders its fumes and flocculent condensation the chief problems in conserving the health of the brass worker. The frequent presence in the foundry air of traces of arsenic compounds, lead

Jan 2, 1919

By Wilder D. Bancroft

It is eight years since I have been connected actively with metallography, but in this time I have been learning something about colloid chemistry, which may be considered as the chemistry of bubbles, drops, grains, filaments, and films, all things in which at least one dimension is very small or in which the surface is large relatively to the mass. Films, of course, suggest to the metallographist Beilby's amorphous film theory, about which I am going to speak for a while, though probably not in the way you expect. I come to bury Beilby, not to praise him. So far as I can judge from looking over the literature hastily, there are two schools in the United States, those who accept Beilby's theory willingly and those who accept it unwillingly. Hoytl says that: At present there seem to be two schools in metallography, one which has adopted the amorphous-phase theory for the explanation of the effect of cold work, mechanical deformation, etc., and one which is not ready at present to adopt this theory. It seems to me that this theory can at least be used as a convenient means of explaining various facts that are demonstrable in the laboratory but the presence of this amorphous material, through our lack of experimental means, we are unable to prove. That we have failed in this direction should not necessarily hinder us from using a theory as workable as this. Mathewson2 says: I have come reluctantly to believe in the amorphous theory, or some theory admitting a modification of the ordinary crystalline phase so as to permit differential properties with temperature, etc. If Mathewson represents one extreme, with Hoyt perhaps occupying a middle ground, H. M. Howe3 may be cited as one of the enthusiastic supporters of Beilby's amorphous theory. It is, says Howe:

Jan 1, 1923

By Wilder D. Bancroft

It is eight years since I have been connected actively with metallography, but in this time I have been learning something about colloid chemistry, which may be considered as the chemistry of bubbles, drops, grains, filaments, and films, all things in which at least one dimension is very small or in which the surface is large relatively to the mass. Films, of course, suggest to the metallographist Beilby's amorphous film theory, about which I am going to speak for a while, though probably not in the way you expect. I come to bury Beilby, not to praise him. So far as I can judge from looking over the literature hastily, there are two schools in the United States, those who accept Beilby's theory willingly and those who accept it unwillingly. Hoytl says that: At present there seem to be two schools in metallography, one which has adopted the amorphous-phase theory for the explanation of the effect of cold work, mechanical deformation, etc., and one which is not ready at present to adopt this theory. It seems to me that this theory can at least be used as a convenient means of explaining various facts that are demonstrable in the laboratory but the presence of this amorphous material, through our lack of experimental means, we are unable to prove. That we have failed in this direction should not necessarily hinder us from using a theory as workable as this. Mathewson2 says: I have come reluctantly to believe in the amorphous theory, or some theory admitting a modification of the ordinary crystalline phase so as to permit differential properties with temperature, etc. If Mathewson represents one extreme, with Hoyt perhaps occupying a middle ground, H. M. Howe3 may be cited as one of the enthusiastic supporters of Beilby's amorphous theory. It is, says Howe:

Jan 1, 1923

By D. G. Westlake, U. F. Kocks

WHILE single crystals of most materials with cph lattice structure show essentially unlimited ductility, polycrystalline specimens of the same materials exhibit the entire range of ductilities. A difference between the ductility of single crystals and polycrystals may be associated with the special stress concentrations to be expected, for example, at the intersections of slip bands or twin lamellae with grain boundaries. Whether such stress concentrations prove catastrophic depends on the cleavage strength of the material, the size of the stress concentrations, and the speed with which they are formed. Thus, the ductility may vary in degree from material to material. Another possible reason for differences in ductility between single crystals and polycrystals is that a sufficient number of independent deformation modes must be available to insure compatibility between the macroscopic strains in neighboring grains.''2 This criterion is often taken to be a necessary condition for any polycrystal ductility whatsoever, not as one that determines different degrees of ductility; thus, a material with an insufficient number of independent deformation modes would have to be brittle as a polycrystal. The "sufficient number" is five if every grain is to accommodate arbitrary shape changes ("von Mises criterion "). We should like to argue that fewer than five independent modes may be sufficient to satisfy compatibility conditions; and that the internal stresses set up when the plastic strains are not compatible reach the theoretical fracture stress only after a significant amount of macroscopic strain has taken place which may vary in magnitude from case to case, allowing an influence on the degree of ductility. Experimental evidence for these statements is taken from the following review of the number of independent deformation modes observed in the various cph

Jan 1, 1968

By W. H. Adams

Virginia, a store-house of metals, is more and more a surprise to the present generation. With her enormous available mineral wealth, worked upon steadily for over a century, exploited SUEciently to demonstrate beyond question costs and values, reported upon by our most eminent scientists, written up by thoroughly earnest correspondents, we yet find her little understood by capitalists or practical men, and until very lately overlooked by the advanceguard of pioneers in metallurgy, whose restless energy conquered the wilderness of Northern Michigan years ago, and has written a new and startling history for almost impenetrable Western territories. The world is learning through the mouths of giant furnaces lately put in blast at Lowmoor, Goshen, and Roanoke, more of this wondcrful State. It is becoming plain that nearer home, amid all the surroundings of civilization, under an equable climate and with the advantage of a minimum cost for fuel and labor, there are stores of mineral, varied in character and deposited over a wide area, which exceed all ordinary calcnlations. Principal among these minerals, iron ores have been, and will probably continue to be, the leading product and the source of greatest revenue. My attention has been called during the past year to one particular section of the iron-belt, where for forty years charcoal-furnaces were successfully operated, the ores being mined in open pits, as can so frequently be seen from the Connecticut line southward into Georgia. There is, however, a significant peculiarity in the character of these deposits of Louisa county warranting special mention, as it is thought that nowhere on the earth's surface, within so moderate a distance of tidewater, can their like be fouad. Probably half a million tons of lump and wash-material have been taken from pits

Jan 1, 1884

By David Baker

Our large modern blast-furnaces, equipped with ore-bins, larries and mechanical means for putting stock into storage, withdrawing it therefrom, and charging it at the tunnel-head, are indeed wonderful in capacity; yet, it is admitted that, with some notable exceptions, they have disappointed us in economy—that is, in the items of low fuel-consumption, uniformity of product, freedom from slips, and reduced cost of repairs and relining. The manager who estimated the cost of pig-iron to be made in a modern plant, by taking the costs of the hand-filled furnace and deducting the amount to be saved by the mechanical appliances, has been surprised, in many cases, to find that unfavorable results in these items of economy have greatly reduced his expected gains. Is there any reason why the fuel-consumption should be greater for a modern furnace than for an older stack using the same mixture ? Certainly the equipment is much more complete, and the trouble, therefore, must lie in the management or in the character of that equipment. Everybody knows that intelligent and vigilant management is a prime requisite: that any neglect of a detail, though it may not be felt that day or week, will surely sooner or later make its appearance as an increased item of cost. But to hold the furnace-maaager responsible for the relatively poor work of the modern blast-furnace would be, I am convinced, a great injustice. For its management has received much more study and care than was given to the older types. Many furnace-managers have lost their health through worrying over this problem, and some hare lost their positions, being held responsible for results made inevitable, as I believe, by the equipment provided for them.

Jan 1, 1905

By R. L. Wilcox, M. L. Fuller

Owing to the nature of the die-casting process, fresllly cast alloys are undoubtedly not at equilibrium from the standpoint of alloy phase relationships. After casting, therefore, they tend to undergo phase changes, with the ultimate effeet of reaching a state of equilibrium at the aging temperature, beyond which no fnrther change takes place. This phase alteration undoubtedly is one of the primary causes of the changes in dimensions and physical properties that zinc-alloy die castings undergo during aging. It is planned to report on this problem in a series of papers of which this is the first. The writers have made a study of commercial zinc die-casting alloys over a period of several years, utilizing the X-ray diffraction technic of determining the phase composition changes in the alloys. Up to the present, two principal phase changes have been observed which are capable of causing dimensional changes: (I) the segregation of secondary constituents from the zinc-base solid solution and (2) the beta aluminum-zinc decomposition. The latter is the subject of the present paper and studies on the former will be reported upon at a future time. Scope of Study In the present investigation a special technic for the study of the beta phase in zinc-alloy die castings has been developed, making possible the determination of the period of existence of the beta phase after casting. The pure beta constituent and its decomposition have been studied in detail. The effect of magnesium and copper on the velocity of the decomposition is reported. The heat of decomposition, the eutectoid temperature arid the accompanying density change have been measured. The density change lias been calculated from data on crystal structure and the result thus obtained has been compared with the actual change.

Jan 1, 1935

By R. L. Wilcox, M. L. Fuller

Owing to the nature of the die-casting process, fresllly cast alloys are undoubtedly not at equilibrium from the standpoint of alloy phase relationships. After casting, therefore, they tend to undergo phase changes, with the ultimate effeet of reaching a state of equilibrium at the aging temperature, beyond which no fnrther change takes place. This phase alteration undoubtedly is one of the primary causes of the changes in dimensions and physical properties that zinc-alloy die castings undergo during aging. It is planned to report on this problem in a series of papers of which this is the first. The writers have made a study of commercial zinc die-casting alloys over a period of several years, utilizing the X-ray diffraction technic of determining the phase composition changes in the alloys. Up to the present, two principal phase changes have been observed which are capable of causing dimensional changes: (I) the segregation of secondary constituents from the zinc-base solid solution and (2) the beta aluminum-zinc decomposition. The latter is the subject of the present paper and studies on the former will be reported upon at a future time. Scope of Study In the present investigation a special technic for the study of the beta phase in zinc-alloy die castings has been developed, making possible the determination of the period of existence of the beta phase after casting. The pure beta constituent and its decomposition have been studied in detail. The effect of magnesium and copper on the velocity of the decomposition is reported. The heat of decomposition, the eutectoid temperature arid the accompanying density change have been measured. The density change lias been calculated from data on crystal structure and the result thus obtained has been compared with the actual change.

Jan 1, 1935

By G. F. Comstock

H. M. BOYLSTON, Cambridge, Mass.-It might be asked, since this test is so simple, why it was not discovered before. It seems to me the explanation is that when we have used the sodium picrate solution, it has .generally been on a very, high-carbon or hypereutectoid steel; to detect . the presence of free cementite, and when we have looked for sulphides, it

Jan 4, 1917

By J. H. Wright

Longhole sublevel stopes excavate ore with which the production geologist has only remote contact; therefore, predicting grade and tonnage from such a stope can be a problem. However, the longholes themselves yield data that can be used to improve those predictions. Here, a radial distribution method of weighting sample data is discussed, which is useful in forecasting grade and tonnage from certain longhole sublevel stopes.

Jan 1, 1985