Search Documents

By John Pew

PRIOR to the development of the bulk-oil carrier, practically all transportation of oil was in barrels and in cans contained in wooden cases; the latter was known as case oil. In the year 1885, approximately two hundred million gallons of petroleum were exported from this country in barrels and about one and three-quarter millions in bulk; less than twelve years later, the shipment in barrels had decreased to nearly one and three-quarter million gallons, while the transport of bulk oil had increased to four hundred eighty-four million gallons. The first modern tanker, the "Glückauf," was built in England in 1886. Her hull, which was 300 ft. long, was divided into compartments by transverse bulk-heads, these compartments being divided by longitu-dinal center-line bulkheads extending throughout the oil spaces. There was a pump room forward of the boiler room, thus providing a cofferdam or safety space. Between the main and upper decks, a narrow trunk extended the full length of the' oil spaces, the trans-verse and longitudinal bulkheads being carried to the upper deck. This allowed for the expansion of the oil from a rise in temperature, and if the tank below the main deck was kept full, the danger of the oil moving with the roll and pitch of the vessel was considerably reduced. Spaces for the carriage of light oil were provided on each side of the vessel outboard of the expansion trunk, while water ballast was carried under the machinery compartments fore and aft. Although vessels previously had been built to carry oil next to the skin of the ship, it is claimed that the "Glückauf" was the first one constructed on the new principle outlined.

Jan 12, 1922

By William Catron

BECAUSE the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for eco-nomic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It was clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stopes below with disastrous results to men and mine. The method of mining developed during the years 1928, 1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled clown gradually on the edges of the stopes, descending a total of about 50 ft. vertically. The men in the stopes had ample to warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost.

Jan 1, 1938

The following is an incomplete list of members and guests who called at Institute headquarters during the period Nov. 10, 1918 to Dec. 10, 1918. Arthur C. Adair, Camp Meade, Md. L. S. Mitchell, Montreal, Canada. Arthur K. Adams, Camp Humphreys, Va. T. E. Mitchell, San Francisco, Cal. Toner Antisell, Chevy Chase, Md. H. Mortimer-Lamb, Montreal, Canada. V. W. Aubel, New Castle, Pa. Edmund Newton, A. C. Black, El Paso, Tex. Paul T. Norton, Jr., Columbus Ohio. 0. F. Brinton, Baxter Spgs., Kans. Elmer W. Pehrson, San José, Cal. C. S. Corbett, Minneapolis, Minn. Joseph E. Pogue, Washington, D. C. W. M. Corse, Mansfield, Ohio. T. C. Roberts, E. Orange, N. J. G. C. Crossley, Toms River, N. J. D. R. Semmes, Richmond, Va. H. S. Emlaw, Grand Haven, Mich. H. L. Slosson, Jr., San Francisco, Cal. Rudolph Emmel, Boston, Mass. W. H. Staver, S. G. Garrett, U. S. N. R. F. A. L. Sweetser, Boston, Mass. Lt. Francis Geib, Denver, Colo. Lt. H. B. Taylor, Kansas City, Mo. Wm. E. Hubbard, Wichita Falls, Tex. Kirby Thomas, New York. Arthur Iddings, Wichita Falls, Tex. Benj. F. Tibby, Salt Lake City, U. Zay Jeffries, Cleveland, Ohio. J. L. Towne, Whitepine, Colo. S. J. Kidder, Mogollon, N. M. Chas. W. Tubby, St. Paul, Minn. Lt.-Col. W. H. Lanagan (Engrs.). A. G. Waite, Brookline, Mass. Major W. F. Lewis (Engrs.). Timothy D. Walsh, Denver, Colo. 0. M. Lewyn, Thomas Warner, Phoenix, Ariz. A. McClintock, DeKalb June., N. Y. J. P. B. Webster, London, England. Major Donald G. Miller, N. M. E. W. Westervelt, Los Angeles, Cal. C. E. LeN. Arnold, formerly with the Inspiration Cons. Copper Co. at Inspiration, Ariz., has accepted a position with the Consolidated Arizona Smelting Co. at Mayer, Ariz.

Jan 1, 1919

By T. S. Lovering

Geochemical prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector's hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930's in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War II, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects.

Oct 1, 1955

E. T. DUMBLE, Houston, Tex.-This paper is a continuation of one that was published by Mr. Garfias, I believe, in the Journal of Geology, 1912, in which he gave the results of his investigations in Mexico, showing that the basalt extrusions frequently did not come up as cones. but reached the surface as a small neck and then mushroomed out into a sill, penetrating the beds both in limestones and in shales. He has continued his investigations to show that as these basalt protrusions came up they forced the strata into a funnel shape at the top instead of throwing them out altogether. While this may be true concerning these particular beds, there are other places at which the basalt does appear clearly as cones and dories, and there the funnel structure does not exist. We know that the sills are there, because we find them in the wells. In one well that I know of. we found a 2-ft. sill of basalt at about 1600 ft. and oil below it at about 2100 ft.; others have gone through similar beds. We also know that there. are cones, because north of the Ranuco River one well struck basalt at about 800 ft. and continued in it for several hundred feet-did not pass through it at all. This paper of Mr. Garfias will give us considerable help in that oil field. W. E. WRATHER, Wichita Falls, Tex.-I would like to ask for information as to the temperatures of Mexican oils. I have heard a number of conflicting reports about the high temperatures of the water and oil, and the relationship between them.

Jan 1, 1918

LIST OF REFERENCES COMPILED BY ENGINEERING SOCIETIES LIBRARY FUEL POSSIBILITIES IN STEEL MAKING. Iron Age, November 6, 1913, p. 1056-1059. Paper read before the American Iron and Steel Institute, by William Whigham. The author discusses the use of pulverized coal as a fuel for open-hearth furnaces. IMPROVED PULVERIZED FUEL FEED DEVICE. Iron Age, November 6, 1913, p. 1024. Brief description of the Dunn apparatus, especially intended for cement kilns, but used also in the nodulizing of iron ore. WIDER UTILIZATION OF PULVERIZED COAL, H. R. Barnhurst. Iron Age, October 23, 1913, p. 906-908. Part of discussion of paper by James Lord on The Use of Pulverized Fuel in Metallurgical Furnaces, read before the Engineers' Society of Western Pennsylvania. POWDERED COAL FOR OPEN HEARTH FURNACES. Iron Age, October 16, 1913, p. 855. Abstract from the "Coal and Coke Operator." USE OF PULVERIZED COAL AS A FUEL FOR BOILERS, R. C. Carpenter. Sibley Journal of Engineering, December 1913, p. 85. COAL-DUST FIRED BOILER. Indian Engineering, November 29, 1913, p. 301. PROGRESS IN FUEL UTILIZATION. Mining and Scientific Press, October 25, 1913, p. 638. BUFFALO GRAIN-ELEVATOR DUST EXPLOSION. Engineering News, July 31, 1913, p. 223-24. Reprinted in the National Fire Protection Association Quarterly, October, 1913, p. 149-151. Mention is made of the danger of explosions in connection with the burning of powdered coal. POWDERED FUEL AND EXPLOSIONS. Railway Age Gazette, July 18, 1913, p. 53-84. Letter by W. D. Wood. USE OF PULVERIZED COAL IN METALLURGICAL FURNACES, James Lord. Engineers' Society of Western Pennsylvania, Proc., October, 1913, p. 363-371; discussion, p. 371-417. With bibliography.

Jan 3, 1914

By A. R. Denison

This field in 1933 continued as in 1932, although to a much less extent, to dominate the drilling and production situation throughout the oil business. The 2466 producers completed in this field during the year are 28 per cent of such wells completed in the United States. The 2556 completions reported in the five counties within which the East Texas field lies are 21 per cent of all such wells reported in the United States. It follows that with such a command of the development situation, every other factor with regard to this field has an important bearing on the entire oil business. As a consequence, the important developments in the East Texas field are the important developments of the year. Very little new productive territory was added to the already known limits of this enormous field. On the other hand, drilling has shown that with a few very minor exceptions this field is a continuous productive area, with a regular outline and no "dry spots" other than that of a single well surrounded by producing wells. Drilling was confined to the already proven limits of the field. This consisted essentially of more adequate coverage of leases by wells, the meeting of required offsets and the drilling of a large number of small tracts which developed from subdivision of larger leases due to court action and other causes. The allowable throughout the year was, with minor variable factors, on a per-well basis. With the steady decline in per-well allowable after May, every operator was faced with declining

Jan 1, 1934

By H. F. Beeghly

UNTIL recently the only criteria by which steels were judged were their cost and their mechanical, chemical, and physical properties. The user was concerned with such properties as corrosion resistance, tensile strength, response to thermal treatment, hardness, ductility, and, to a growing extent in recent years, with behavior at high temperature. As plans were made to build power reactors, a new set of properties became important—the nuclear characteristics, which had to be considered by the designer and engineer in building his plant. The nuclear engineer developed methods for the rare and new metals and produced them in high purity, often at great expense. The pure metals then provided the raw materials for tailor-made alloys. For more common structural metals, such as steel, the nuclear industry depended on commercially available materials. Generally, the quantities required were small and specifications were rigid. It is not surprising, therefore, that difficulty was frequently encountered in procuring structural mate-

Jan 1, 1957

By E. A. Beck

(New York Meeting. February, 1913.) For a number of years many attempts have been made to use thermit in order to do away with piping in ingots. Some of these attempts were successful, while others did not give the expected results. Nearly every plant had its own method of using the thermit, and no special care was taken to study, the results or to find the causes for lack of success. Formerly the principle of the process was to decrease the piping by introducing a can filled with thermit, attached to an iron rod, into the head of the ingot directly after it bad been poured. In this case the thermit reaction took place in the upper part of the ingot, and it was thought that through the heat produced the head would keep liquid longer and piping thus be reduced. In other words, the aim was to keep the head of the ingot open by making use of the heat of the thermit reaction, which would thereby give the gases in the steel sufficient time to escape. This result can be attained by the application of a large enough quantity of thermit, but it would not be economical in general practice, and could only be used for high-grade material. Many steel-makers abroad and in this country have had this experience. The Th. Goldschmidt A. G., Germany, has, therefore, made a special study of this question with the co-operation of a well-known steel company, and has worked out a new method for. the application of thermit for this purpose. The results obtained have been most satisfactory and reliable, and this- process is now used in Germany on a large scale in many prominent steel-works.

Jan 4, 1913

By B. O. Pickard

WITH more than a score of shafts and numerous stope openings to the surface, all inter-connected underground; with underground temperatures high, often exceeding 100° wet bulb; with an ore presenting a dust health-hazard; with certain rocks giving off inert gases; with an altitude of 6000 ft. above the sea level and a dry desert climate, the Tonopah mines offered an interesting, problem to the student of metal-mine ventilation. Tonopah is not an old mining district relatively speaking. It was discovered in 1900 and Tonopah soon was a boom camp. By 1910 the mines of this district had paid many millions of dollars in dividends. At the time of the 1921 ventilation study, mining had passed its peak of production and the operators were striving to reduce costs, to discover new ore bodies, and to attract desirable workmen. In 1925, the camp was operating on a still less prosperous basis, but the several managements had not relaxed in their efforts to keep the mines on a paying basis, neither had they lost their faith in the ability of the mines and the price of the silver to "come back." Early in the fall of 1921 the Bureau of Mines was invited by the mine operators at Tonopah, Nevada, to make a detailed study of the under-ground air conditions in the Tonopah silver district. D. Harrington,? who was then directly supervising the ventilation studies of the bureau, detailed district engineer B. 0. Pickard, mining engineer E. D. Gardner, surgeon C. E. Kindall, and petrographer H. Insley to carry on the study. G. S. Rice, as chief mining engineer of the Bureau of Mines, was in general charge of the work. Upon the completion of the study each operator was furnished a report on conditions in his mine.

Jan 2, 1927

TO THE BOARD OF DIRECTORS OF AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-I have the honor to present the following, report for the calendar year 1920. The activities which seem to call for special comment are: THE NEW FORM OF MAGAZINE MINING AND METALLURGY appeared every month during the calendar year and has been developed until it contains some ten departments. It has brought forth more commendatory letters than have been received at headquarters on any other subject throughout the year. Less than a dozen letters unfavorable to the change have been received, and the indications are that the magazine has met a want deeply felt, especially by members distant from headquarters. The technical papers printed by the Institute are published in abstract in the magazine and opportunity is given to members who desire them to receive full copies of any or all papers published. The Bound Volumes, as usual, contain all the papers in full and discussions thereof. FINANCES The greatly increased cost of paper and printing has put a tremendous burden on the Institute's finances, since the dues of $12 per year are only 20 per cent. greater than the members paid when the Institute was founded forty-nine years ago. This has resulted in a temporary deficit, similar to that encountered by many of our sister engineering societies. The fact that our Institute has lower dues and gives more in the way of publications to its members than any other of the national engineering societies has rendered the situation more difficult for us. MEETINGS The Annual Meeting in New York, the Field Meeting in the Lake Superior District, the meeting of the Petroleum and Gas members at St. Louis, and of the Institute of Metals Division in Columbus, Ohio, have all been described in full in the magazine.

Jan 1, 1925

By William M. Brewer

Until quite recently, in fact within the past two gears, but little attention has been given to the outcrops on the west coast of Vancouver Island, and their copper-contents. During the past few months the writer has been engaged in examining and developing some of these prospects. In many respects he has found characteristics associated with these prospects which, in his experience, are unique. In the first place, nearly all the outcroppings which overlie chalcopyrite-ore along the west coast of the island are composed of a high-grade magnetite. The magnetic qualities of some of these outcrops arc so pronounced that the magnetite possesses polarity. Although the writer hinlsclf had no analyses of this magnetite made, yet from its appearance he can readily believe that analyses made for other parties, which show a yield' of 62 or 63 per cent. of metallic iron, with only traces of phosphorus and silica, are correct. At a very shallow depth, masses of chalcopyrite, yielding in some instances as high as 32.6 per cent. of copper, occur associated with the magnetite; and in one instance, which recently came under the writer's observation, a solid body of high-grade chalcopyrite, fully 4 feet in thickness, occurs Within 6 feet of ; the surface. Usually this solid sulphide-ore carries low values in gold. Probably ail average of' $2 per toil would be fairly representative. But in some instances development has determined the occurrence of narrow stringers of pyritous quartz, associated with the sulphide-ores, which yield by assay more than $20 per ton in gold. In the districts examined by the writer, the country-rock is usually crystalline limestone, with dikes of igneous rock as intrusions. Sometimes the outcrops of magnetic iron-ore are

Jan 1, 1900

By Clifford Frondel

THE aluminum oxide known as corundum has several varieties that have been used as gem materials since ancient times. These include the red variety called ruby, the blue variety sapphire, and the asteriated types of ruby and sapphire. Asteriated sapphire was known to the ancients under the name of astrios, and descriptions of this gem were given by Pliny and other early writers. The relation of these gem materials to each other as varieties of a single species, corundum, was first clearly established by Haüy in 1805 and J. M. Güthe' in 1809. Natural gem corundum is obtained principally in Ceylon, Siam, Burma, India, and Australia. Star sapphires and rubies always have been highly prized and in recent years have become particu- larly popular in the United States. Natural star rubies of large size and fine quality are extremely rare and rank with large and fine emeralds and diamonds as the most valuable of gem stones. Interest thus attaches to the recent success in commercially synthesizing star sapphires and rubies of a size and perfection unmatched by nature. Corundum was first synthesized as crystals in 1837 by A. Gaudin, who fused alum and aluminum oxide with potassium sulphate. Numerous other syntheses have been reported in more recent years. Summaries of this work are given in Doelter's Hand-buch der Mineralchemie, Mellor's Compreheizsive Treatise of Inorganic Chemistry, and other reference works. The methods employed include the reaction in the gaseous state at high temperatures of halogen compounds of aluminum with water vapor or boric oxide; the crystallization of aluminum oxide from fusion in potassium molybdate, potassium dichrom-ate or borax; and crystallization from highly aluminous silicate melts. Red, blue, or green colored varieties can be obtained by the addition of small

Jan 1, 1955

By Kenneth Seaver

Discussion of the paper of KENNETH SEAVER, presented at the San Francisco meeting, September, 1915 and at the New York meeting, February, 1916, and printed in Bulletin No. 105, September, 1915, pp. 1913 to 1927. WILLIAM HUTTON BLAUVELT, Syracuse, N. Y.-I think that Professor Richards' statement regarding the reason for the failure of the Bethlehem ovens was due to a misconception on his part. Silica bricks were not used because the ovens were built under German design and management and it has not been the practice in Europe to use silica brick nor has it been necessary, on account of their lower heats and slower coking time as compared with the present American practice. J. W. RICHARDS, So. Bethlehem, Pa.-While acting as Chairman at the San Francisco meeting, in introducing this paper of Mr. Seaver, I made some remarks in discussion referring to unsuitable brick having been used in a coke plant at So. Bethlehem, Pa., and being the principal cause of the failure of these ovens. This statement having come to the attention of the Didier-March Co. of Perth Amboy, N. J., who furnished the firebrick used in the construction in the original ovens referred to, at the Lehigh Coke Works, near So. Bethlehem, Pa., their. manager, Geo. A. Balz has corresponded with me, and wishes to have placed on record a general denial of the statement referred to. As a matter of justice to the manufacturers of the firebrick, it is but right that their statement should be given as much publicity as my statement which has been objected to, and I take pleasure in placing upon record the statement of Mr. Balz, general manager for Didier-March Co., extracted from a letter to me dated Jan. 14, as follows: "The

Jan 5, 1916

By Leonard Larson

DURING several years immediately preceding the adoption of wet-charge smelting at McGill, various necessary conditions affecting this procedure, such as plant rearrangement and the metallurgical nature of the concentrate produced at the concentrator, were fully considered. Wet-charge smelting is not altogether novel to the recently recon-structed smelter at McGill. A number of years prior to this improve-ment, when flotation methods were initiated at the concentrator, large tonnages of wet and (at that time) sticky flotation concentrate were charged directly into the reverberatory furnaces, because of the difficulty in handling the entire tonnage in the roasters. The plant had excess reverberatory units and this surplus furnace capacity was utilized to smelt raw flotation concentrate. During the years 1927 and 1928, a number of actual operating furnace test runs were made to determine in principle the feasibility of wet-smelt-ing operation. Results were encouraging, and in November 1932 the roasting plant was shut clown. For some time thereafter the wet feed was delivered directly to the reverberatory side-charging calcine hoppers already in place. Feeding the wet material through the old calcine hoppers and charge holes into the furnace involved considerable labor, but under the conditions existing at that time it was desirable to continue wet smelting even under the handicap of this laborious procedure. The smelting plant during this period was on a curtailed production basis, operating only about 15 days per month. The alternate starting up and shutting clown of the roasting plant presented a difficult problem and charging the wet material directly to the furnace entirely eliminated this difficulty. The roasting plant was never operated thereafter.

Jan 1, 1938

By P. P. Goudkoff

UNDER the name of the Russian Far East we understand the territory occupied by the Amur, Maritime, Sakhalin and Kamchatka Provinces, the total area of which is about 918,000 square miles. The mining industry took its first step in the Russian Far East in the second half of the 19th century, and until the end of this century was restricted to gold placer mining. In the last years of the 19th century, the extraction of coal and lignite was begun, and in 1910-11 the exploitation of silver-lead-zinc mines. The conditions of the Far Eastern mining industry during the last few years may be outlined by the following figures. Annual production of gold mines was about 54,000 lb., valued at $13,000,000. During the period of 1910-15 a considerable increase of placer-gold mining by mechanical processes took place; in 1910, by means of dredging and excavators, 500 lb.. of gold were obtained; in 1914, 2740 pounds. Annual output of coal; lignite and. silver-lead-zinc ores was: 1911 1920 Bituminous and semi-anthracite coal, long tons 270,000 316,000 Lignite, long tons 66,000 205,000 Silver-lead-zinc ores, long tons 28,400 94,500 In other branches of mining in the Far East, only the quarrying of building stone and clay may be men-tioned, the total yearly output amounting to about $500,000 in value. The principal gold mines are in the Amur Province, in the systems of the Zeia and Bureia rivers, and in Kamchatka Province, near the town of Okhotsk. The above-mentioned tonnage of coal and lignite was extracted from the mines in the Maritime Province, near Vladivostok. The only silver-lead-zinc mine worked was that of Tetiukhe, near the Tetiukhe Bay, 240 miles northeast of Vladivostok. The ores of this mine were exported to Germany, Belgium, and Japan, partly raw, partly calcined.

Jan 6, 1922

By O. B. Hopkins

Activity in the oil industry in Peru during 1930 was confined almost entirely to the three old producing fields in the northern coastal area. In the eastern part of Peru, in the valleys of the Maranon, Ueayali and Huallaga rivers, additional geologic work was carried on, but no drilling was undertaken. The Peruvian Government granted a concession on June 27, 1930, to W. R. Davis and associates for the building of a railroad from the west coast at Bayovar to Yurimaguas on the Huallaga River. This concession contemplates the construction of 800 to 900 km. of railroad across the Andes and carries with it a grant to the concessionaire of 12,500,000 acres of land with oil and mineral rights. A similar concession was granted in 1926 but after several extensions was rescinded in July, 1929, on the grounds that the concessionaire had failed to begin work on the railroad within the time limits of the contract and its extensions. The production in barrels from the three coastal fields of Peru has been as follows: 1929 1930 International Petroleum Co.......................... 10,821,117 9,766,922 Lobitos Oilfields, Ltd................................ 2,508,091 2,613,511 Zorritos........................................... 75,000a 78,000a 13,404,208 12,459,060 a Estimated. No definite figures available. Although not large, the Peruvian production has been steady during the past years. The reduction of approximately 8 per cent. in 1930 as compared with 1929 is the result of the world's overproduction and the attempt on the part of the International to restrict the output to conform with the available market. International Petroleum Company International Petroleum Co. owns the oldest producing property in Peru. The first well was drilled there in 1872. The cumulative production from the property from 1900 to 1930 inclusive has been over 92,000,-000 bbl. from an area of 15,000 acres. The recovery per acre has varied

Jan 1, 1931

On Dec. 8, 1916, at a meeting held at the Massachusetts Institute of Technology, the John Fritz Medal was presented to Professor Elihu, Thomson, "for his achievements in electrical invention, in electrical engineering, in industrial development and,in scientific research." Professor Albert Sauveur presided. John J. Carty, chairman of the Presentation Committee of the Board of Award, made a short address-on the history and significance of the medal. He was followed by E. W. Rice, Jr., president of the General Electric Co., who spoke at length of the achievements of Dr. Thomson, whom he called "one of the world's most prolific and industrious inventors and scientists." Among other things, he said: "In the, field of electrical inventions alone, Professor Thomson has been awarded something over 550 United States patents, and in other fields; notably mechanical work, about 150 patent.,. he has made contributions to the world's scientific, and technical literature, in several hundred articles describing not only his own dis-coveries and inventions but making remarkably interesting contributions to scientific speculation and thought. "A skilled workman, he is always able himself to do the work which he asks others to perform. "His inventions are the result of such profound and accurate knowledge,. and developed with such skill, that they almost invariably work on the first, trial in accordance with expectation." Dr. Richard C. Maclaurin, President of the Massachusetts Institute of Technology, spoke of the personality of the man as well as of his accomplishments, as follows: "He has not only clone great things himself, but has shown ,in intense desire to help all who are struggling earnestly with scientific problems. He has proved an inspiration to an ever-widening circle of engineers and others who have entrusted him with their secrets and sought his help in overcoming their difficulties. They have done this knowing. that they had only to ask in order to get the full benefit of his

Jan 2, 1917

Executive Committee. GEORGE F. KUNZ, Chairman. E. GIBBON SPILSBURY, Vice-Chairman. THOMAS ROBINS, H. J. SEAMAN. Louis D. HUNTOON, Secretary-Treasurer. Meeting, Apr. 4, 1913. A joint meeting of the New York Section of the American Institute of Mining Engineers, the American Society of Mechanical Engineers, and the American Institute of Electrical Engineers was held in the large auditorium of the Engineering Societies Building, 29 West 39th Street, on Friday evening, Apr. 4, 1913, and an exhibition of the Edison Talking Moving Pictures was presented before the Societies, together with exhibitions of the work which is being done by the Edison Co. in making moving pictures to illustrate lectures on natural science and the useful arts for school and college work. Introductory remarks were made by Mr. J. W. Lieb, Jr., and followed by an exhibition of moving pictures illustrating the formation of crystals, the operation of different types of pumps, magnetic forces, electro-magnetic separation of iron ore, the evolution of the fly, and many other most interesting studies. One of the films, entitled The Formation of Crystals, showed a moving picture of a boy, whose laboratory was the kitchen, dissolving salt in a test tube filled with hot water. The boy then poured the solution of hot salt into a watch glass and placed it under the microscope to watch the crystals form. This film was immediately followed by another showing what the boy saw through the microscope. The solution at first was free from crystals. Gradually the crystals commenced to form and increased very rapidly after once starting, shooting across the screen with lightning speed. The film illustrating the separation of iron ores by the Edison electro-magnet showed an ore bin with an electro-magnet set at one side and below the bin. As the ore was dropped from the bin the magnetite was drawn into the. electric field and deposited in a separate rile from the sand.

Jan 5, 1913

By Pol Duwez, Ellis P. Frink, Paul Pietrokowsky

Ti-Au alloys in the composition interval 0 to 66 213 atomic pct Au have been studied over a temperature range from 400° to 1500°C. A partial phase diagram has been established from micrographic and macroscopic observations. All intermediate phases, Ti3Au, TiAu, and TiAu., exhibit open melting maxima. It has been observed that small additions of gold lower the allotropic transformation temperature of titanium. The P solid solution decomposes eutectoidally to a solid solution plus Ti3Au. The solubility of gold in a solid solution decreases with temperature. THERE have been several papers in the literature pertaining to the alloy system Ti-Au. However, a comprehensive study of this interesting constitu- tion diagram has not been conducted. Previous investigations have been concerned with the crystal structure of intermediate phases or partial phase diagrams. This paper represents a partial constitution diagram, Ti-TiAu,, the first portion of an investigation of the entire binary system. Laves and Wallbaum' reported the intermediate phase Ti,Au to be isomorphous with CuAu, L12 type. In a more recent paper, Duwez and Jordan' have concluded that TiAu has an atomic arrangement which is related to Cr,Si. The intermediate phase

Jan 1, 1957