Search Documents

By C. Feng, I. R. Kramer

A study was conducted to determine the influence of the surface on the yield point of fcc metals and high-purity iron. For the high-purity fcc metals, the yield Point produced by restraining a specimen may be eliminated by removing a sufficient amount of the layer. A yield point similar to that in fcc metals was found when iron specimens were pre-strained after a prior deformation. This yield point is not due to an aging effect but is associated with the surface layer. The yield points in age-hardenable aluminum alloy and those connected with "work softening" are not affected by a surface-removal treatment and are, therefore, caused by bulk-type dislocation reactions. The yield point which appears in previously strained fcc metals has been the subject of numerous studies. Several theories have been advanced to explain this "unloading-reloading" yield point. Cottrell and stokes,' from their study on the effect of temperature on plastic properties of high-purity aluminum, considered that it was the result of an avalanche "breakdown" of Lomer-Cottrell sessile dislocations. Haasen and Kelly2 extended this concept of dislocation-dislocation interaction to account for the yield point when unloading and reloading was carried out at the same temperature. On the other hand, strain aging was found to be responsible for the yield point in A1-Mg alloy by Westwood and Broom,3 and in aluminum alloys containing various amounts of alloying elements by Smallman, Williamson, and Ardley.4 In these cases, the yield point is considered to be associated with the locking of dislocations by impurity atoms. Birn-baum and filer5,6 and Takamura and muira7 reported that, when a high-purity copper specimen was prestrained, then held at a lower stress, and finally reloaded at the prestrain temperature, a larger yield point was observed. Such an increase was attributed to the locking of dislocations by point defects. In addition, Bolling8 suggested that both mechanisms, i.e., dislocation-dislocation interaction and strain aging, are responsible for the yield phenomenon, at least in a brass. Thus, there appears to be experimental evidence for both the strain aging and dislocation-dislocation interaction theories to explain the yield point in the fcc metals and alloys. In a previous article,9 one of the authors observed that, if sufficient amounts of metal were electrolti-cally removed after deformation of a high-purity aluminum single crystal, the yield point did not appear upon reloading. Continued pursuit in this area revealed that the effect of the surface on the yield-point phenomenon is not limited to one metal but affects a variety of metals of different lattice structures. Nor is the effect limited to the yield points produced by simple unloading-reloading at constant temperature; the surface exerts an important role on the yield point even when the temperature is changed at some stage during the test. It is the intent of the present article to give additional information regarding the effect of the surface on the yield-point phenomenon and to show the association between the yield point in both fcc and bcc metals and the existence of a heavy concentration of dislocation in the region near the surface of a deformed specimen.10 EXPERIMENTAL Materials. The single crystals used in this study had a nominal cross section of 0.125 by 0.125 in. and a 3-in. gage length and were prepared by a modified Bridgman technique. The initial purity for the metals was 99.997, 99.999, and 99.999 pct for aluminum, copper, and gold, respectively. Bar stock of these same materials was used in the preparation of the polycrystalline specimens of aluminum and copper. The iron specimens were machined from rods of "ferrovac", reported to have a purity of 99.98 pct. In addition, a precipitation-hardening aluminum alloy, containing 1.5 pct Cu, 2.5 pct Mg, and 5.5 pct Zn, was used. The polycrystalline specimens of iron, copper, and the aluminum alloy had a diameter of 0.17 in. and a gage length of 2 in. while the high-purity aluminum specimen had a nominal rec-

Jan 1, 1965

By T. Egleston

The Boston and Colorado Smelting Works are situated in the town of Black Hawk, Gilpin County, Colorado, on the Clear Creek Narrow Gauge Railway, 55 miles from Denver, in the Rocky Mountains, at an altitude of 7800 feet. It was one of the first works erected for the metallurgical treatment of gold ores, and the only one established in Colorado on a large scale which has been uniformly successful. Both gold and silver ores are treated, and gold, silver, and copper produced. The lead is not separated from the ores nor paid for, if it exists, and is entirely lost in the residues. The works were planned and built by Professor Hill, formerly Professor of Chemistry in Brown University, Providence, R. I., and is still managed by him, assisted by Mr. Richard Pearce, formerly professor in the School of Mines at Truro, England. They are very advantageously situated with regard to the ore-producing regions, having Boulder County on the north, which produces, besides ordinary gold ores, a series of tellurium minerals, such as altaite, sylvanite, and hessite, which are very rich in gold and silver. They are associated with copper and iron pyrites, blende, galena, and the carbonate and oxides of iron. Gilpin County itself produces for the most part the pyrites of iron and copper rich in gold, with a small quantity of galena and blende, which is rich in silver. In

By T. PH. D. Egleston

THE Boston and Colorado Smelting Works are situated in the town of Black Hawk, Gilpin County, Colorado, on the Clear Creek Narrow Gauge Railway, 55 miles from Denver, in the Rocky Mountains, at an altitude of 7800 feet. It was one of the first works erected for the metallurgical treatment of gold ores, and the only one established in Colorado on a large scale which has been uniformly successful. Both gold and silver ores are treated, and gold, silver, and copper produced. The lead is not separated from the ores nor paid for, if it exists, and is entirely lost in the residues. The works were planned and built by Professor Hill, formerly Professor of Chemistry in Brown University, Providence, R. I., and is still managed by him, assisted by Mr. Richard Pearce, formerly professor in the School of Mines at Truro, England. They are very advantageously situated with regard to the ore-producing regions, having Boulder County on the north, which produces, besides ordinary gold ores, a series of tellurium minerals, such as altaite, sylvanite, and hessite, which are very rich in gold and silver. They are associated with copper and iron pyrites, blende, galena, and the carbonate and oxides of iron. Gilpin County itself produces for the most part the pyrites of iron and copper rich in gold, with a small quantity of galena and blende, which is rich in silver. In * By consent of the council of the Institute, this paper was first published in London Engineering, from which the engravings are here reproduced.

Jan 1, 1876

By Eduardo J. Chibas

Location.—The principal manganese-deposits of the Department of Panama, Republic of Colombia, are located almost clue south of Viento Frio, a native village bordering on the Caribbean Sea, and about 45 miles northeast of Colon (Aspinwall). The mining-claims are the Viento Frio, the Carrano, the Nispero, and the Soledad. Each property is to the south of the preceding one in the order mentioned. The first one is about one mile from the coast, and the most southerly boundary of the Soledad is about five miles in a straight line from the same coast-line. I shall confine my remarks to the four properties mentioned and to La Guaca, west of the Carrano, because these are the only ones where mining has so far been done to more or less extent. Manganese has also been found, however, in the neighborhood of these deposits, and a large area adjoining them has been divided into sections and " denounced " as mining-claims. The relative position of the manganese-deposits and Nombre de Dios, the present terminal of the railroad and shipping-port, as well as Viento Frio and the adjacent coast, can

Jan 1, 1898

By A. English, M. J. Greaves

This paper is a discussion of pelletizing systems developed over the last 15 to 20 years for the agglomeration of fine iron ore concentrates. Five different pelletizing systems are now in commercial use in the U.S., and for the purposes of comparison, estimated operating costs and capital costs for the construction of four of them are included. Capacities of existing commercial plants are examined, together with the anticipated capabilities of plants presently being built or projected. In just 21 years, the art of pelletizing iron ore concentrates has reached maturity with mastery of the separation of finely divided concentrates from low-grade iron ores and their agglomeration into pellets containing about 65% iron. This accomplishment has firmly established an improved feed for the blast furnace, with resulting benefits in faster reduction of burdens and greater economy of operation. The present production capacity of pelletizing facilities in the U.S. is about 20 million tons annually, and it is expected to double by 1970. The rapid expansion of pelletizing in the U. S. has been closely observed in European countries, notably in Sweden and Germany, where pioneer agglomerating techniques were developed early in this century. PELLETIZING PLANTS AND PROCESSES Twelve commercial pelletizing plants are presently in operation in the U. S. and Canada. An equal number are in various stages of engineering and construction, and many others are being considered. The pelletizing systems currently employed include shaft furnaces, horizontal grates using three different airflow arrangements, and grate kilns. The capacity of pelletizing operations in North America is shown in Table I. All of these plants are integrated with the mine, the ore-crushing facilities and the concentrating plant and are equipped with storage and loading-out facilities for the product. Normally, a pelletizing plant is composed of a shuttle conveyor above the receiving bins; balling equipment; a heat-hardening system including the necessary auxiliaries such as furnaces, burners and controls, ducts, fans, meters and instrumentation; fines recovery equipment; and product handling equipment. Also included are the necessary auxiliaries and utilities such as boilers or power plant; oil unloading and storage facilities; coal unloading storage, grinding and distribution facilities; and bentonite or other additive storage and distribution equipment. Shaft Furnaces: Vertical shaft furnaces used in this country are limited to the treatment of natural magnetite concentrates containing minor quantities of residual fluxing elements. Fig. 1 shows a perspective view of the shaft furnace with balling, feeding and pellet-handling equipment. An elevation of a shaft furnace is shown in Fig. 2. A commercial shaft furnace unit is about 45 ft in height with a 6 x 14-ft rectangular cross section and has a nominal production rate of approximately 50 gross tons of pellets per hour. The upper portion of the furnace shaft is constructed of fire brick as protection from the high process temperatures involved. The lower portion of the shaft is lined with abrasion-resistant brick to withstand erosion from the fired pellets. Rectangular-shaped, refractory-lined and insulated combustion chambers are situated on each side of the shaft furnace. Oil or gas is burned to produce high temperature gases which are forced into the furnace through ports located near the top of the combustion chambers. The shaft furnaces operate at a pressure of approximately 6 psi. Pellets are fed into the top of the furnace by a pantographic feeder designed to produce the desired pellet stockline. The furnace is kept filled at all times and pellets are fed and discharged from the furnace at the same rate. In early development, 10 to 12 lb of solid fuel was incorporated in the pellets. However, the main source of process heat is now derived from the combustion chamber gases. In some instances no solid fuel is used. The pellet movement in the shaft furnace is counter-current to the flow of gases. Ambient air is introduced through louvers at the lower end of the furnace, at about 6 psi, cooling the fired pellets and supplementing the heat of the high temperature gases from the combustion chamber ports. The zone of maximum temperature, located above the ports of the combus-

Jan 1, 1963

By F. G. Jaicks

RECOGNITION of the benefits to be gained from the continuous casting of molten steel into finished or semifinished products has been given by scientific minds since the very beginnings of steel plant technology. In fact, Sir Henry Bessemer is credited with the first of a long list of patents' issued by the U. S. Patent Office for a process which would accomplish this desirable end. None of these early ideas attained practical success and, as a result, the conventional method of teeming into ingot molds became an integral part of modern steelmaking operations. This procedure, although refined to keep pace with the changes which have come about in steelmaking and finishing facilities, is recognized to have inherent shortcomings which adversely affect manufacturing costs and steel quality. Interest in the continuous casting of steel persists because the process is directed toward avoiding some obvious weaknesses of conventional ingot casting. It has been recognized that should it be possible to substitute any of the continuous casting techniques under current development for ingot casting, it would no longer be necessary to make large capital investments in primary rolling equipment, the sole purpose of which is to reduce ingot castings to a form rollable on finishing mills. The results reported in the continuous casting of non-ferrous metals and specialty steels indicate that in addition to avoiding the primary rolling mills there is some basis for expecting significant improvements in yield, surface, and internal quality. Recognizing the shortcomings of the conventional procedures, the Inland Steel Co., in cooperation with Atlas Steels Ltd. and the Freyn Dept. of the Kop- pers Co. Inc., embarked upon a program to evaluate certain aspects of continuous casting in order to determine whether the process could be applied practically to an existing integrated steel plant producing 'large tonnages of carbon steels. TO assist in this evaluation a study was carried out in which several types of low carbon steel were continuously cast in an existing machine. It is the purpose of this paper to review some of the results obtained in the casting studies and to interpret the information that was obtained so as to indicate factors that must be considered in assessing operating limitations and plant capacities. Despite the early interest in the continuous casting of steel, the actual application to the steel industry is relatively recent. At present, there are about 25 operating plants casting steel, most of which have been built in the past decade. None of these plants could be classified as large in terms of the tonnages that are being processed by the major integrated steel plants. In contrast to the situation in the steel industry, there has been widespread adoption of the continuous process in the casting of nonferrous alloys, particularly aluminum and copper. As a result, much of the basic information that was required to apply the process to steel was developed in the nonferrous industries. In this respect, a most important contribution was the development of the Junghans2 system, which was initially designed for the casting of nonferrous metals and later applied to the casting of steel. Alternative methods for casting have also been proposed by Babcock and Wilcox Tube Co.,'" the British Iron and Steel Research Association,5 and the Gebruder Bohler A. G.13 Each of these methods is now being used successfully for the casting of special steels in small experimental plants or in modest sized commercial steelworks. The Original Junghans process was first developcd in Germany. Further application of the process has been made by Rossi in other countries.'*' The experi-

Jan 1, 1958

By Charles A. Chase

This paper, descriptive of a single mine, is presented in the belief that it may furnish useful suggestions to mine-managers encountering similar problems; and it includes the details which will enable them to estimate the value of the methods employed—especially where these depart from common practice. Tt should be added, however, that this mine is not typical of the San Juan district, but differs markedly from neighboring mines in physical conditions and metallurgical requirements. The Liberty Bell mine is situated in San Miguel county, Colo., on the west front of the San Juan mountains, 2 miles north of Telluride. The vein was discovered in 1876 by Wm. L. Cornett, who, with subsequeilt locators, took up claims along the apex. A few hundred feet of development-work was accomplished, and a few? tons of ore were smelted or milled; but profitable working proved impossible under existing

Jan 1, 1912

By A. H. Tousley

Current problems in the cement industry are discussed and suggestions for solving them by modernization are made. Cement facility modernization is discussed in considerable detail with examples illustrating before and after conditions. Itemized are the improvements realized in better working conditions, better efficiency, higher production, lower costs, and better community relations. These improvements are related to the overall profitability of the particular plant or facility.

Jan 1, 1972

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By Ernest R. Woakes

Cana, originally called Santa Cruz de Cana, is situated in the province of Darien, in the Republic of Colombia, S. A. The river Cana is a tributary of the Tuyra, which flows into the Gulf of San Miguel, and thence into the Pacific Ocean some 80 rniles S.E. of the City of Panama. • The Espiritu Santo mine lies on the S. side of the Cana river at the foot of the Espiritu Santo range. The plateau of Cana has an elevation of 2000 feet above sea-level, and the mine is about 200 feet above the plateau. The map of the Darien accompanying this paper is the only correct one in existence. It was made by Lucien N. Bonaparte Wyse for the Panama Canal Co., and has been copied fur the present use, with permission, by Mr. L. G. Inglis. The dotted line on this map shows the route from the coast to Cana. As this mine was one of the most celebrated at the time of the Spanish occupation, it is only natural that there are a great many traditions and writings concerning its former workers and production. Dampier mentions it, though he does not seem to have been nearer to it than El Real de Santa Maria, the port on the Rio Tuyra, about 50 miles by road from Cana. Senor Vicente Restrepo's work, entitled Estudio sobre las Minas de Oro y Plata de Colombia, translated by C. TV. Fisher and published in New York in 1886, is, perhaps, the best treatise on Colombian mines. He has devoted a great deal of attention to the subject of the Espiritu Santo mine, and has had access to all that dealt with it in the archives of Bogota. It will be interesting to quote a few pasaages from the above work, which seemed like a romance to the writer of this paper some years ago, when he first came across the history. Being actually in Cana at the time, and knowing the present company had

Jan 1, 1900

By Heinrich Ries

Fullers' earth is a clay-like substance, which has the property of decolorizing or clarifying oils. An ultimate chemical analysis shows it to differ from most ordinary clays in having usually a high percentage of combined water and a low amount of alumina. There is probably a large amount of hydrous silica present. Fullers' earth possesses little or no plasticity, and in order to work properly has to be ground very fine. A chemical analysis is of little value at present in determining its quality; only a practical test suffices. Up to about two years ago all of the fullers' earth used in this country was imported from England; but about that time deposits were discovered in Florida, "† and since then rumors of its occurrence have been coming from all parts of the country. Next to the Florida deposits of fullers' earth, those of South Dakota are the most extensive thus far discovered in this country. The earth was first discovered near Fairburn, Custer county, and other deposits have since been prospected at Argyle, Minnekahta and other localities. Fairburn.—One of the first deposits located and opened up is five miles southeast of Fairburn, Custer county. The mine is a mile from the Fremont, Elkhorn and Missouri Valley Railroad, and the section exposed shows, beginning at the top: Feet. Micaceous sandy clay,......... 6 Fullers' earth,..........9 Micaceous sandstone,......... The fullers' earth passes upwards into the sandy clay, but in its purer portions it is a yellowish, gritty clay, with a somewhat

Jan 1, 1898

By C. W. Lawr

The ores mined by the Santa Gertrudis Co. at Pachuca, Mexico, arc mainly silver-bearing; they also yield some gold and carry a little copper. Strong cyanide solutions are used to dissolve the silver and gold, and the mechanical loss of cyanide at the tailings filter has been considerable. Prior to the year 1923, the pulp, after agitation, was given a 35 to 37-min. wash with barren solution in a Butters-type leaf filter; the discharged slime cake was repulped and pumped into eight Merrill self-sluicing slime presses in which the slime was given a further wash with barren solution for 25 to 35 min., followed by a 10-min. water wash. At that time the barren solution titrated around 0.350 per cent. free KCN and 0.500 per cent. total KCN. (Aero brand cyanide is used.) It can readily be seen that a 10-min. water wash would leave considerable cyanide in the filter cake, which of course was a total loss. This averaged 0.522 kg. (1.15 Ib.) KCN per ton of solution. As the daily discharge to the dam was 1600 tons' of slime of a 2:1 ratio of liquid to solid, the value of this mechanical loss of cyanide was an important item and it's recovery held alluring possibilities. Principle of Cyanide-recovery Process As it had acquired the patent rights to theLayng (H. R.) and Halvor-sen (A. L.) processes, also those of Mills (L. D.) and Crowe (T. B.) after considerable experimental work in its own laboratory and at Tonopah, Nev., The Merrill Company of San Francisco early in 1923 notified the Mexican Corporation and compania de Santa Gertrudis of its process for the recovery of cyanide from weak wash solutions, or for the transference of cyanide from a foul mill solution to a clean alkaline solution. This method is known as the Mills-Crowe process, the principle of which is as follows: The solution from which the cyanidc is to be removed is made acid by bringing it into contact with sulfur dioxide (SO2). The acidified solution is the; transferred to a closed tank in which air and solution are brought into intimate contact. The air leaving the tank charged with HCN is then passed to another tank in which it is mixed with an alkaline solution,

Jan 1, 1930

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions' the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures' When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By AIME AIME

FOUK fields of activity are now recognized by the A.I.M.E. in its award of medals for conspicuous achievement: the Saunders medal for mining, the Douglas medal for non- ferrous metallurgy the Lucai medal for petroleum, and the Rand medal for distinguished achievement in the broad field of mining administration including the organization and development of enterprises in all branches of the mineral industry. This last is known officially as the Charles F. Rand Memorial Medal, and it award is made possible through funds supplied by the Charles F. Rand Foundation. Until this year money thus available was used for other special projects, so that the forthcoming presentation of the Rand medal to Robert C. Stanley is notable as being the first time that achievement in mining administration has been thus recognized.

Jan 1, 1940

By Clyde E. Williams, V. N. Krivobok, C. H. Herty

THE extreme effect of the depression on the steel industry is well illustrated by the fact that the amount of iron ore shipped from the Lake Superior district was the lowest in 47 years. Something over 3 1/2 million tons of ore was shipped in 1932, compared with over 65 million tons in 1929. It is not surprising then that practically no advancement in iron ore beneficiation has been made. Improved research and development work, however, was continued at the Michigan College of Mines in the survey of the lean iron ores of Michigan with reference to the possibility of their concentration; at the University of Minnesota in its large-scale jigging studies of Lake :Superior ores; and at Battelle Memorial Institute in the development of improved jigging of iron ores. The successful operation of the new Hadsel mill at a gold property in California gave such low grinding costs on a quartz ore as to give much encouragement in the iron ore industry for a cheapening of the cost of grinding lean ores for concentration.

Jan 1, 1933

By Elliot Rexford

The quality of aggregate materials is of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 3, 1950

E. A. H. Tays, San Blas, Sinaloa, Mex. (communication to the Secretary*):—The results obtained by Messrs. Hofman and Hayward in their experiments, proving that a low percentage of copper sulphate with a variable percentage of salt, depending on the ore, gives the best results, confirm practical mill-work which I did in 1895. I have none of my notes, taken at the time, to refer to, so have to rely solely on memory, which precludes the conciseness that is alway desirable. In 1894 I took charge of the plant of the San Rafael Company, near Chinipas, Chihuahua, Mex., which at that time was treating a very refractory ore carrying about $15 in gold and from 20 to 25 oz. of silver per ton, the bullion being about 300 fine in gold. The silver in the ore was in the form of a sulphide. Although carrying an average of 0.75 oz. of gold per ton, free gold could rarely be seen by panning, but upon roasting a sample of the ore the gold became visible at once—a result which was discovered by chance and used to advantage later. In order to utilize the old mill to the best advantage, it was decided to use pan-amalgamation after roasting. The roasting, done in a lime-kiln, was similar to the ordinary " burning " operation. The roasted ore was trammed to the mill-bins and crushed by 10 stamps to pass a 30-mesh screen. The pulp was de-watered and fed to four 1-ton pans. My recollection is that upon starting the mill-work, the charge contained 1.5 lb. of copper sulphate and 5 per cent. of salt per ton. From the start the extraction was unsatisfactory and the loss of quicksilver was very large. Experiments were then carried out on a working scale. First, the quantity of copper sulphate was increased 4 oz. at a time; then it was reduced

Jan 1, 1910

By AIME AIME

CORROSION of tanks, pipes and other equipment in the oil fields is becoming worse as the production of high- sulfur crudes in the Texas panhandle and west Texas areas increases. It has been estimated that .in certain fields of that State one tank out of every five has to be replaced every year because of the high sulfur content of the crude. One suggested method for combating tank corrosion is the use of .materials which have a high resistance to the corrosive action of hydrogen sulfide and high-sulfur crudes; aluminum is one of these materials. As a result, the United

Jan 1, 1929

By Alexander R. Troiano, Eugene P. Klier

Since the very early work on quenched structures, where the products of the martensite transformation had been recognizedl this transformation has provoked much interest and study. Theoretically it was desirable to account for the extreme changes in physical properties resulting from the formation of martensite, as that information might lead to results of practical importance. Desirable information, therefore, was on the kinetics of transformation from austenite to martensite as well as on the physical constitution of the martensite. It has been known for years that certain steels quenched to room temperature will contain persistent austenite as well as martensite. Other important and now well-established features of the martensite reaction are the Progress of the reaction on cooling only and the independence of Ar" with cooling velocities exceeding the critical velocity. These facts have been experimentally determined by various methods and investigators. Notable among the early investigators were Tammann and Scheill and Wever and Engel.2 Unfor- tunately, all investigators did not fully interpret their results, which, coupled with several investigations that yielde. conflicting resultsl caused a state of confusion that was not clarified until quite recently. X-ray investigations of martensite in steels3-6 indicate it to be a supersaturated solid solution of carbon in alpha iron. This supersaturation is evident from the appearance of a body-centered tetragonal structure with the addition of sufficient carbon. The dimensions of this tetragonal structure are a linear function of the carbon content within the limits of accuracy of the determinations. Slight tempering of tetragonal martensite leads to the destructi,, of the tetragonal structure, which is converted to a body-centered cubic strutture. This phenomenon has precipitated a controversy concerning the nature and mechanism of the tempering of martensite The facts in the case have been outlined by Epstein7 and more recently by Antia, Fletcher, and Cohen.8 The significance of Ar" on theoretical grounds is not clear, however, although considerable study has been devoted to its determination. The precise position of Art' aS a function of carbon content was first stated by Greninger and Troiano9 for steels covering a range of approximately 0.7 to 1.8 per cent carbon. The effect of alloying elements on Ar" has recently been the subject matter of investigation by various methods.

Jan 1, 1945