Search Documents

By Leo P. Tarasov

Magnetic torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade&apos;s2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time2,5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements. Magnetic Torque Method It is fairly well known nowadays that single crystals of ferromagnetic substances have directions of easy magnetization and of hard magnetization. In Fig. 1 are reproduced typical magnetization curves for a single crystal of iron, which show that in a < 100 > direction saturation occurs at low fields compared to those required to saturate the same crystal in a <110> or a <111> direction. (The magnetization intensity I is defined by the equation B = H + 4pI.) At fields high enough to

Jan 1, 1939

By J. M. Locke

BRÜCKNER&apos;s revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. As examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,, Ohio, are shown in Plate III, in which Fig. 1 is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a trans¬verse section. Fig. 4 is a sketch of a mill, with Brückner&apos;s cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches.. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi¬circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15° to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30° to 35° to the longitudinal, axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between

Jan 1, 1874

By Willis H. Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world&apos;s deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104º at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By J. M. Neilson

The occurrence of iron ore deposits in the State of Western Australia has been known at least since the 1930&apos;s,3 but the true significance of the deposits has only come to light within the past four years. Although they are widely distributed throughout the State, it is now known that more than 90% of the available iron ore reserves are located in the "Hamersley Iron Province". Western Australia may well contain the world&apos;s largest known reserves of iron ore. Recent reports place this reserve at 15 billion tons and an even higher figure may appear in the future. LOCATION, CULTURE AND COMMUNICATIONS It is difficult to comprehend the immense size of Western Australia (Fig. 1). The State occupies almost one million sq miles and it is more than 2000 miles from north to south. More specifically, it stretches from the 14th to the 35th parallel of latitude south. The Ophthalmia Region in the Hamersley Iron Province is barely halfway up the long dimension of the State. Nevertheless, the region is 800 miles north of Perth, a distance comparable to that from New York to Chicago or to that from Chicago to New Orleans. The Hamersley Iron Province (so named in 1963 to distinguish it from the Pilbara mineral district adjacent to it on the north) covers an area of approximately 30,000 sq miles in the northwestern part of the State. It extends in a roughly oval form from the Indian Ocean to the Gibson Desert of the interior, a distance of about 300 miles. With the exception of the small coastal towns of Onslow, Roebourne and Port Hedland and a few other communities such as the asbestos-mining town of Wittenoom, the region is very sparsely populated. Sheep and cattle stations are scattered thfough the region and these and the main towns are connected by truck tracks and a few main highways. Voice communication is almost entirely by the short-wave radio net operated by the Royal Flying Doctor

Jan 1, 1965

By Warden A. Moller

(Pittsburg Meeting, March, 1910.) THE Fushun coal-field, now being opened up by the South Manchurian Railway Co., is connected with the main line by a branch, 30 miles long, from Sui Chia Tun, 10 miles south of Mukden, the capital of Manchuria. The coal-field, which lies on the southern bank of the Hun river, 25 miles east of Mukden, consists of a long narrow valley,. running east and west between hills composed of granitic and volcanic rocks. At the foot of the northern hills, the Hun river flows westward towards the Liao river, which drains the greater part of South Manchuria. At the foot of the southern hills, resting immediately upon volcanic rocks, and overlain by 20 ft. of alluvial, is a thick layer of Tertiary shales, carrying near the base two coal-seams. In many places the lower of these two seams is in immediate contact with volcanic lauds and basalts, the flows of which were evidently both prior and subsequent to the formation of the coal-seams. This contact has practically destroyed the lower seam for commercial purposes. The value of the field lies in the upper seam, which, for a length of nearly 8 miles, varies from 100 to 130 ft. thick. Of this seam, 85 per cent is good coal. The seam dips to the north conformably with the shales, at angles of from 25° to 30°, and appears to have an uninterrupted dip for about 1.5 miles before being possibly cut o$&apos; by the northern hills. The coal-bearing shales extend east and west for a length of about 20 miles, but towards the east the continuity of the seams is broken by intrusive rocks. The coal is of the sub-bituminous variety, low in ash, bright in appearance, and breaks with a conchoidal fracture. It has the usual qualities of Tertiary coal-quick steam-raising and poor stacking-qualities. Pieces of resin, varying in size from

Apr 1, 1910

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By Thomas Read

PERSONNEL work is a term recently introduced to cover the great variety of activities in industrial work that deal with the human factor. Much attention has been focussed upon individual phases of personnel work, such as accident prevention, sanitation, "welfare" work, reducing labor&apos; turnover, and so on. In most cases these activities have been carried on as though they were distinct and separate fields; as a matter of fact, they are only different phases of the single problem of human engineering, and each has important and fundamental relations with the others. Thus, for example, high labor turnover is one of the most .important causes of a high accident rate, and unsatisfactory housing conditions are an important cause of labor turnover. In the early stages of the study of these problems, it was necessary to take them up separately; the time has now arrived at which it is desirable to consider them as a whole in order to bring them into the right relation to each other. When thus considered as phases of an interrelated whole, they may be grouped as personnel work. A discussion of the importance of personnel work as a means of in creasing dividends in industry may be objected to by some as a too materialistic way of looking upon work that is humanitarian. Nothing could he more mistaken than such an opinion. Humanitarianism, per se, has no place in industry, and nothing is gained and much is lost in pre tending that it has. The only reason why a corporation engages in business is to make profits, and any activity of the corporation that does not tend either directly or indirectly toward that end is poor business. It is equally poor business to overlook any activities that do tend indirectly to the making of profits. On this basis, personnel work can be justified as a corporate activity; there is no justification whatever for abstract humanitarianism from the business standpoint. One characteristic of the American workman is a general high level of intelligence, and it is an insult to intelligence to ask a man to believe that anything so impersonal as a corporation is really desirous of benefiting

Jan 10, 1917

By Robert Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 4th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 3rd edition (1960) of Industrial Minerals and Rocks will clearly demonstrate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Re- view. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 3rd edition of Industrial Minerals and Rocks. Most of these, of course, are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 11th annual meeting in 1975, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the U.S. Geological Survey and the U.S. Bureau of Mines. The two agencies publish many reports and maps on a variety of geo- logical and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications. (New Publications of the Geological Survey, U.S. Geological Survey, Washington, D.C. 20242) and New Publications-Bureau of Mines, Publications Distribution Branch, U.S. Bureau of Mines, 4800 Forbes Ave., Pittsburgh, Pa. 15213). The U.S. Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, and 1970. Three other major series of publications by the Bureau are Information Circulars, Reports of Investigations, and Mineral Trade Notes. The latter is particularly good for news of foreign developments. A new Professional Paper No. 820 of the U.S. Geological Survey, 1973, summarizes data on the mineral resources of the entire country. The USGS, in cooperation with USBM, other Federal and various state agencies, has also prepared summary reports on mineral and water resources of given areas which include

Jan 1, 1975

By Hsun Hu, R. S. Cline

The effect of rate of deformation on texture formatiotz has been studied with cube-oriented single crystals of 3 pct Si-Fe, compressed 80 pct at two widely different rates. Compression at a low rate (crosshead speed, 0.1 ipm) produces large orienta-tional changes and coarse deformation bands, whereas little change in orientation is observed, particularly at the surface of the crystal, when compressed at a high rate (impact velocity, -500 ips). Thin plates of mechanical twins are produced at the high rate, but their contribution to the deformation texture is practically negligible. The crystal deformed at a high rate has a lower hardness and a more uniform dislocation structure and is morc resistant to recrystallization. There is also a dilference in the recrystallization texture between the slowly and rapidly compressed crystals. These results indicate that plastic flow is less "turbulent" at high strain rates than at low strain ratcs. THE behavior of metals under high-speed deformation has been the subject of wide study in the past decade. Most of these works were concerned with mechanical properties during testing at high rates of loading, the resulting structures, and the theoretical aspects of the observed phenomena. The present status of knowledge and research activities in this field has been documented in recent publications.17&apos; There is, however, very little information available in the literature concerning the effect of high-speed deformation on the texture formation in metals. The possibility of an effect of rate of deformation on texture is suggested by the microstructural differences observed between normally and very rapidly deformed samples. Aside from the strong tendency for twinning (and phase transformation in certain metals) in high-speed deformation, the slip-line patterns and the dislocation configurations show marked differences as a result of large differences in the strain rates. For instance, in mild steel in static and dynamic compression, Campbell and co-worker3,4 observed that coarse slip occurred on several systems in specimens deformed at normal strain rates, whereas specimens deformed rapidly showed only fine slip on fewer systems, the slip-line pattern being very similar to that in specimens deformed at low temperatures and at normal strain rates. The absence of multiple slip was also noticed by Dieter5 in shock-loaded nickel. The dislocation configuration in an iron shock loaded at 70 kbar pressure was shown by Leslie et al.6 to be similar to that produced by light rolling at low temperature—the dislocation lines were mostly straight and uniformly distributed. These observations suggest that the mode of deformation at high strain rates is notably different from that at low strain rates. Consequently, the nature and the extent of lattice reori-entation during deformation should also be different. This investigation was undertaken to test this idea. MATERIAL AND METHOD The remaining part of a single-crystal ingot of a 3 pct Si-Fe alloy,* prepared for an earlier investi- gation,1 was used in the present studies. Specimens 9/16 in. square and 0.365 in. thick were cut from this ingot with (001) planes parallel to the square surfaces, and the [loo] and 1010] directions parallel to the edges of the specimen, within ±1 deg. These machined crystals were etched to remove distorted metal, and annealed at 1300°C for 24 hr in a purified helium atmosphere. The annealed crystals had a hardness of 161 Dph. The crystal orientation was rechecked with X-ray back-reflection techniques. In high-strain rate experiments the crystal was compressed in a Dynapak machine to approximately 80 pct reduction in thickness (from 0.360 to 0.070 in. with an impact velocity of -500 ips). Thus, the duration of loading was approximately 6x 10-4 sec, and the average strain rate was about 103 sec-1. As a result of this rapid, severe deformation, the specimen became a roughly circular thin disc. The original shape of the crystal, however, could still be recognized by a diffusely outlined square area in the center of the disc. For compression at a low speed, the crystal was deformed in a universal testing machine at a rate of crosshead movement of 0.1 ipm. Compared with

Jan 1, 1965

By Paul Billingsley

Introduction. THE Georgetown mining district is located in Deerlodge county, Mont., about 20 miles west of Anaconda. It lies along the divide between the headwaters of Warm Springs creek, draining eastward, and Flint creek, flowing west and north through the Philipsburg valley. The actual divide is formed by Cable mountain, a narrow ridge running north and south, terminating to the south in low hills overlooking Georgetown lake, and to the north in a high, rugged plateau that falls off to the west to the wide valley of Flint creek. Oil the eastern, or Warm Springs, slope of Cable mountain is the Cable mine, with the Hidden Lake mine a few miles north. On the western slope is the Southern Cross group, with smaller mines, the Twilight, Cincinnati, Red Lion, and Big Bill, at intervals to the northward. The Georgetown mines lie in the hills south of Cable mountain; the Philipsburg mines, of which the Granite Mountain, Bimetallic, Hope, and Trout are the chief, form a separate group to the north, overlooking Flint Creek valley and Philipsburg. (See Fig. 1.1) The region ranges in elevation from 5,000 to 9,000 ft. It is, with the exception of the lower valleys, well timbered with small fir and pine, although Cable mountain and the higher summits to the northward rise slightly above timber line. The main valleys have the smooth contours of glaciation, and their mouths are frequently choked with morainal deposits.

Jan 9, 1913

By L. A. Roe, E. A. Elevatorski

Wollastonite, named after William H. Wollaston, an English chemist, is a calcium metasilicate, CaSiO3; CaO: 48.30%, SiO2: 51.70%. It has a short history as an industrial mineral. The earliest production of wollastonite is reported to be from a deposit near Code Siding, located north of Randsburg, CA. At this locality small tonnages of wollastonite were quarried during 1933-34 and 1938-41, and processed into mineral wool. This operation was largely experimental and virtually no United States production was again reported until the 1950s when a large deposit near Willsboro, NY, was developed by the Cabot Corp. A processing plant was placed onstream in 1953, with nearly continuous production to date. It is currently operated by NYCO, a division of Processed Minerals, Inc. Since 1958, wollastonite deposits in the Little and Big Maria Mountains of Riverside County, and in the Panamint Range of Inyo County, both in California, have operated intermittently for production of both ornamental and commercial wollastonite. During 1980, the United States was the major producing country, furnishing about 75% of the world&apos;s output. Current production comes from Finland, Mexico, India, and Kenya. Small amounts have been shipped intermittently from the USSR, New Zealand, Republic of the Sudan, Republic of South Africa, and Namibia (South-West Africa). The principal use of wollastonite is in the manufacture of plastics. Other uses are for paints, ceramics, adhesives, fluxes, glazes, thermal insulation board, and refractory products. Mineralogy Pure wollastonite, CaSiO3, has the composition of 48.3% CaO and 51.7% SiO2. However, it is seldom found in the pure state due to the ease with which it takes into solution the metasilicates of manganese, magnesium, iron, and strontium. Predominantly, wollastonite occurs as a contact metamorphic deposit forming between limestones and igneous rocks. Commonly associated minerals are garnet, diopside, epidote, calcite, and quartz. It has a specific gravity of 2.8 to 3.0, and hardness of 4.5 to 5 on Mohs&apos; scale. When pure, it has a brilliant white color, but with impurities it may be grayish or brownish. Luster is vitreous to pearly. Melting point of wollastonite is about 1540ºC. Wollastonite occurs in coarse-bladed masses, rarely showing good crystal form. It is usually acicular or fibrous, even in the smallest of particles. The most unique property of crushed and ground wollastonite is its cleavage. Fragments of crushed wollastonite tend to be needle-shaped, imparting a high strength, and this property is the basis for many of its uses. The fiber lengths are commonly in the ratio of 7 or 8 to 1, length to diameter. The average diameter of wollastonite is 3.5 µm. Some crystals of wollastonite fluoresce under short-wave or longwave ultraviolet light, or both, with colors ranging from yellow-orange to pink-orange. Specimens may also show phosphorescence. The acicularity of wollastonite is a property of considerable importance to the marketplace. The plastics industry makes utilization of high aspect ratio grades of wollastonite (20:1) for reinforcing thermoplastics and thermoset polymer compounds. The naturally high pH of 9.9 (10% water slurry) is a prime property to the coatings industry. The coatings industry uses milled grades of wollastonite as a pH stabilizer in interior and exterior PVA and acrylic latex systems. Processed wollastonite can have a G.E. brightness of 90 to 93. Chemically, wollastonite is inert and this property makes it useful as a filler and reinforcing agent. There are two polymorphs of calcium silicates: wollastonite, a low temperature form, and pseudowollastonite, a high temperature

Jan 1, 1983

By A. U. Seybolt

Experiments on both suljidation and hot corrosion have been carried out using ternary Ni-Cr-X alloys and commercial nickel-base superalloys. It has been shown that lhere are certain micro structural similarities between sulfidation using H,S/H2 mixtures and hot corvosion using Na,S04 in "crucible" experiments or hot corrosion tests using a flame tunnel apparatus. It is proposed that two key processes in the hot cowosion process are: 1) formation of chromium sulfides which deplete the alloy matrix, and 2) oxidation which can be accelerated because of chromium depletion. Other processes play an important role in the hot corrosion process, such as accelerated oxidation attack due to the presence of a N& S04 or N&SO,- NaC2 film which inhibits the formation of a protective external oxide scale. However, this latter phenomenon was not studied in this work. THE term hot corrosion has come to mean a combination of sulfur and oxygen attack on nickel-base or cobalt-base superalloys used as gas turbine blades or partitions. This attack can be initiated by any combustion process in air involving fuel containing sulfur if the sulfur level is sufficiently high. Levels of 5 pet SO2l for example, in the combusting gas have been observed to produce hot corrosion attack on nickel-base alloys. The important immediate corroding medium in aircraft gas turbines, however, has been established to be Na2S04, formed from reaction between NaCl from sea air and sulfur in the fuel.&apos; The Na2S04 concentrates the sulfur sufficiently so that superalloy parts heated in the range 1400" to 1900°F can become sulfided by reducing the Na2S04 film which forms on the parts, and this reaction allows sulfur to gain access to the alloy. The sulfur thus released diffuses into the superalloy and forms primarily chromium sulfides of various compositions, but frequently Cr2S, has been identified. Figs. 1 and 2 show the morphology typical of hot corrosion of a cobalt-base superalloy X-45 (25 Cr, 10 Ni, 7.5 W, 0.25 C) and a nickel-base alloy, Udimet 500 (19 Cr, 19 Co, 4 Mo, 3 Ti, 2.9 Al, 0.07 C). Both alloy samples were subjected to the same hot corrosion conditions: 616 hr at 1600°F in a combusted 2.9 pct S distillate oil containing 125 ppm Na as NaC1. It will be noted at once that the nickel-base alloy is much more severely attacked. The depth of corrosion is much greater and the number and size of the sulfides present are much greater. Both alloys show a duplex oxide scale, which is more noticeable in the X-45 alloy. The external scale is probably a spinel in both cases, with CrQ3 lying next to the alloy. Many investigators1 -"ve been concerned with hot corrosion phenomena, but there has been a lack of unanimity of opinion as to the details of the hot corrosion mechanism. More than one definition of hot corrosion is possible. Some investigators con- sider as a measure of hot corrosion only the weight gain due to an accelerated oxidation. However another point of view is that the total depth of affected alloy may be used as a measure. While it is recognized that surface oxidation attack is greatly accelerated by the presence of salts like Na2S04 or Na2S04-NaC1 mixtures, sulfur penetration into the alloy also undoubtedly produces very important effects. The region of sul-fide penetration which is so prominent in Fig. 2 is one of the outstanding characteristics of hot corrosion. For highly stressed parts, such as first-stage buckets, this sulfur-penetrated region can be more significant in mechanical property loss than the reduction of cross section produced by the formation of the massive external scale. In addition, evidence will be presented that this sulfided region can be less resistant to subsequent oxidation attack. Since it appears that the sulfided region below the surface oxide scale plays an important role in the overall corrosion process,

Jan 1, 1969

By A. Hansson, G. E. Tardiff

WHILE it is generally known that cold-worked low-and medium-carbon steels exhibit substantial increases in tensile rupture ductility with increased deformation velocity172 (up to the von Karman limit), the observations for annealed or normalized steel do not permit simple generalization. Various investigators, for example, have reported both small increases1,3 and small decreases4,5&apos; in rupture ductility with increased rates of deformation of normalized low-carbon steel. The purpose of the present note is to report on the dependence observed for strain-aged steel since preliminary work here indicates that strain aging results in the development of a consistent type of behavior that is understandable in the light of current knowledge of the lower yield dynamics for steels which deform inhomogeneously.6 This realization throws additional light on the influences responsible for the behavior of normalized steel. The results presented here were obtained for a 0.21 pct C, 0.012 pct N sheet (0.012 in. thick) steel which was received in a temper-rolled condition (approximately 3 pct reduction in thickness after process annealing); the as-received material had a spherodized structure with a ferritic grain size of ASTM 8. The material was selected for testing after 6 months room temperature aging, at which time the static lower yield and ultimate tensile strength measured 79 and 82 kpsi, respectively. ASTM 2-in. reduced section, 1/2-in.-wide specimens were used in smooth bar tests and 3/4-in.-wide specimens containing two 60-deg opposed edge notches (root radii = 0.002 in.) were used in notched bar tests. To facilitate strain measurement, the smooth bars were blued with ink and marked at 0.1-in. intervals along the gage length; the notched

Jan 1, 1968

By Gerald Sherman

MINE fires are always dangerous and are frequently accompanied by loss of life during the period of confusion which is apt to follow their discovery. In metal mines, fires may result from the accidental ignition of some combustible material, or they may be of spontaneous origin resulting from the rapid decomposition of sulphide. They occur frequently enough to demonstrate the need of some special equipment and a general plan for controlling them, in addition to measures for their prevention. Nearly all the large copper mines have had fires, and the methods of fighting them have been well described in recent papers, notably-by C. L. Berrien,1 R.. E. Tally,2 and others in discussion. The Copper Queen mine has many shafts, which are connected by underground workings. The deeper parts are ventilated by fans, but in the shallower portions natural ventilation through numerous connecting raises or shafts is sufficient. There have been several fires in the past few years, of which all are extinguished but one, and that is under control. These notes cover particularly the preparations that are being made-to check a new fire, partially or temporarily, and to facilitate the escape of workmen in the interval before a definite plan of fighting it can be established. A fire may occur in a shaft or station, or in some working father away. In case of fire in an upcast shaft, the gas would escape to the surface and the immediate result would probably not be dangerous to workmen, as they could escape by other shafts. In a downcast shaft, however, the gas would be distributed very rapidly throughout a large portion of the mine, and men might easily be trapped and asphyxiated. A fire in mine workings, drift, raise, or stope, would be dangerous in a degree, but the draft there is likely to be less strong than in a shaft and probably a smaller area would be invaded by the fire gases.

Jan 1, 1918

By John Devine

DURING the past few years the Bureau of Mines has been studying hydrogen-sulfide corrosion in the petroleum and natural-gas industries. Early work was confined to investigating the various practical, or operat-ing, factors that control the corrosion reaction when ordinary mild steel is being attacked. In that work it was shown that, if the optimum operating conditions1 are obtainable, . gas containing hydrogen sulfide can be handled at ordinary temperatures without serious corrosion resulting. However, frequently "sour" gas must be handled under other than optimum operating conditions, and combating corrosion then becomes a problem to be considered more during the construction of a system than during its subsequent operation. That is, where economi-cally practicable in such cases the designer will seek to substitute for mild steel other steels or ferrous metals more resistant to corrosion by hydro-gen sulfide. The comparative resistance of various commercial steels and alloy steels to corrosion by hydrogen sulfide at elevated temperatures has been reported systematically by previous investigators,2 but similar information for corrosion at ordinary temperatures is available only from scattered sources, representing different methods of testing. As the value of comparative corrosion tests depends largely upon the use of a

Jan 1, 1934

By Arthur L. Bishop

INTRODUCTION Purpose The in-situ leach method for uranium extraction is a relatively new and innovative method of uranium mining. In 1975, the first commercial in-situ facility began operation in south Texas. Since that time numerous other operations have been initiated as either pilot or commercial ventures. Considerable literature has been published that deals primarily with generalities of the process or environmental concerns. Several federal agencies have published documents which do not reflect the true operating or environmental nature of the in-situ leach method of uranium extraction. From an environmental standpoint, this is also evident in the promulgation of rules and regulations. Hence, the purpose of this paper is to present experience with an environmental concern--non- production zone excursions--such that the industry and the regulatory agencies will gain greater insight devoid of preconceived ideas and misconceptions. General Process Description In south Texas, in-situ leach mining is utilized to extract uranium from permeable sandstone ore deposits 61 to 213 meters (200 to 700 feet) below the surface. Uranium is present as an insoluble uranium oxide. In the in-situ or solution mining technique, anoxidizing lixiviant is injected into the formation through injection wells. The solution reacts with the insol uble carbonate complex. This soluble uranium complex is produced at recovery wells, each containing a submersible pump. During production there is a constant sweeping of lixiviant through the formation from the injection wells to the recovery wells. Injection and recovery wells can be arranged in any of a number of geometric patterns dependent upon ore body configuration, aquifer permeability, and operator preference. Submersible pumps in the recovery wells pump the uranium rich pregnant solution to the initial processing facility. Monitor wells surrcsund the pattern area and are screened in appropriate stratigraphic horizons (production and non-production zones) to detect any lixiviant migration that may occur (Fig. 1).

Jan 1, 1980

By R. U. Jackson

Belt conveying is a method of transportation that requires proper servicing and maintenance if completely economical results are to be obtained from the system. With a trucking system, it is common practice to deliver the trucks to a servicing station each day or at the end of each shift. With railroad transportation there is a similar procedure. Sufficient credit is seldom given to this periodic inspection and maintenance procedure, yet it is the key to the successful operation of trucking and rail haulage systems. How about the belt conveyor transportation system? Here is a system that requires no operator for each individual unit. It requires only a main switch and an adequate sequence interlocking system, and the system is so simple to operate that maintenance is considered as only a casual requirement-nothing is done about it until after trouble has developed.

Jan 1, 1956

By H. N. Hall

Various factors must be considered in an engineering evaluation of gravity-drainage reservoirs. Among these are: (1) the effect of producing rate on total oil recovery; (2) the effect upon well productivity and ultimate recovery of the pressure level maintained during the producing life of the reservoir; (3) the economic advantage of full or partial pressure maintenance; and (4) estimate of the rate of gas production and injection and the possible purchase of gas under conditions of full pressure maintenance to ascertain compressor facilities needed. All of these factors can be evaluated only when a reliable method is employed for determining reservoir performance in gravity-drainage reservoirs. The purpose of this paper is to present a general method for calculating the performance of a gravity-drainage reservoir. This method is applicable for conditions of complete pressure maintenance, partial pressure maintenance and normal pressure depletion. Provisions are made to take into account variations throughout the reservoir of reservoir configuration, changes in permeability and fluid composition. Based on the method presented in this paper, an IBM 650 computer program has been developed. The past performance of an actual gravity-drainage reservoir producing under conditions of declining pressure and no gas injection was duplicated using this program. INTRODUCTION In tilted reservoirs the production of oil is influenced by drainage of oil from upstructure to downstructure locations. When this downstructure drainage of oil is sufficient to cause effective segregation of the gas and oil in a reservoir, the reservoir is usually classified as a segregation drive or gravity-drainage reservoir. (Discussion will be restricted to gravity-drainage reservoirs which have no encroachment of edge water.) The important feature in gravity-drainage reservoirs is the density difference between reservoir oil and gas. These phases tend to segregate in the reservoir with the result that in the gas cap the oil saturation is maintained at a higher level by drainage of oil from the gas-cap area. Oil can be produced from the oil zone at a low gas-oil ratio and reservoir energy is thereby conserved. The standard material balance in not adequate for predicting gravity-dramage reservoir performance because it does not take into account the difference in saturation above and below the gas-oil contact. Several authors&apos;.&apos; have presented methods for calculating the performance of gravity-drainage reservoirs in which reservoir pressure is maintained constant by gas injection into the gas cap. Using some simplifying assumptions, these methods can be employed with a desk calculator to give acceptable results. The problem of predicting the performance of gravity-drainage reservoirs under the conditions of declining reservoir pressure is many time more complex than that of constant pressure. fierefore, attempis to develop a method suitable for desk calculation have required excessively simplified assumptions. In the past several years, highspeed digital computers have become more widely available for reservoir engineering problems. These corn puters are well suited to problems such as the prediction of the performance of gravity-drainage reservoirs with pressure decline. Many of the simplifying assumptions necessary for hand computation can be eliminated so that a realistic approach to the gravity-drainage process can be made. CONCEPTUAL PICTURE OF OIL MOVEMENT IN GRAVITY-DRAINAGE RESERVOIRS Before attempting to develop an analytical treatment for conditions occuring in a gravity-drainage reservoir, a concept should be formed concerning the movement of fluids in the reservoir as oil is produced. A review of the literature&apos;.&apos; shows that it is customary to classify gravity-drainage operations into two categories—(1) with complete pressure maintenance, and (2) with declining pressure. The same line of reasoning will be followed in presenting the concept of the movement of fluids in the reservoir because it is easier to visualize the movement of fluids under conditions of complete pressure maintenance. After discussing complete pressure maintenance, an analogy will be made between that and the case of declining pressure. It should be kept in mind throughout that the final aim for the problem of solving gravity-drainage performance with digital computers will be to develop a general program for any kind of gravity-drainage reservoir. COMPLETE PRESSURE MAINTENANCE One feature which is generally common in gravity-drainage reservoirs is a gas cap located at the top of the structure. This is shown in Fig. 1(a). Fig. l(b) shows oil saturations that might occur through the reservoir. In the gas cap, oil saturation is lower than

By John Wulff, J. H. Hollomon

Service failures in brass condenser tubes are often due to corrosion. One of the commonest types of corrosion reveals a surface structure of redeposited copper.&apos; The study of the effect of alloy addition agents in preventing this kind of corrosion has received impetus from the extensive publication of Bengough and May.2 The mechanism of such inhibition gauged from immersion corrosion,2 cell corrosion,3 and electrolytic potential4 measurements is controversial. This controversy may be attributed in part to a lack of definite knowledge5 of the actual nature of the initial films formed in corrosion experiments. In our own corrosion work on copper and 70-30 brass this lack became apparent and necessitated an examination of surface films by X-ray and electron diffraction methods. The present paper is but an introduction to the subject of inhibition and reports the structure of films formed in active corrodents. Experimental Procedure The arsenical coppers and brasses used in this investigation were made by one of the writers* in the plant of the Revere Copper and Brass Co. at Rome, N. Y. Standard commercial melting practice was followed. O.F.H.C. copper and electrolytic zinc were used and all arsenic additions were made by additions of a master copper alloy. The final analyses are given in Table I. Likewise, the extrusion, cold-rolling, and intermediate anneals employed followed standard usage. Final heat-treatments were given to all materials to produce a similar grain size (0.035 to 0.045 mm. for brass and 0.015 to 0.025 for copper) for the alloys containing various percentages of arsenic. Samples 1/2 by M by 1/4 in. were cut from sheet material resurfaced and finished with 0000 metal-lographic papers. The surfaces were all degreased in alcohol and benzine before immersion. After immersion in the corrodent, they were washed gently in tap water, dipped first in alcohol and then in pure benzine and allowed to dry in the diffraction apparatus. The reflection electron diffraction apparatus used has been described by Burwell and Wu1ff.6 Fig. I is typical of the photo-grams obtained. The X-ray apparatus was

Jan 1, 1941