Search Documents

By A. W. Peake, F. O. Prior

Considering the great advance in the development and application of electricity, it is not strange that eventually a big field for its use has been found in oil-field operations. So far as is known, the first electric drive in oil-field operations was in the Russian field of Baku in 1900. The first application in this country was made by the South Penn Oil Co. near Folsom, West Va. in 1903. In 1916, electric power was first used in the Burma fields of India for drilling and pumping. Between 1916 and 1922, The Empire Gas & Fuel Co. made the first large electrical installation in the Mid-Continent fields. But although the first application was made 27 years ago, it is only within the last 10 years that oil companies have begun to look upon its use with much favor. Within the last few years, there has been a steady increase in the use of electricity in the oil fields. The first application of electricity for oil-field operations in Wyoming was in the Lander field in 1919; the second was in 1924 in Salt Creek; and the third, and last to date, was made by the Continental Oil Co. in the Big Muddy field during 1926. Lander Field The electrification of oil-field operations in Wyoming was initiated by J. W. Steele, superintendent of the Producers & Refiners Oil Corpn., in the Lander field in 1919. At that time, 32 wells were being pumped from five band-wheel powers, with oil engines as the prime movers. Eight barrels of fuel oil were used for power per day and at the price of 90 c. per bbl. the fuel bill was $36 per day. It was decided to try a 15 to 35-hp. oil-field motor on one of these powers. Electric power was generated with steam at the old Wind River refinery station. This test was so successful that in 1920 all five powers were equipped with 15 to 35-hp. oil-field motors, the power being obtained from the Sinks Canyon hydroelectric station. Four of these powers pumped wells at an average depth of 1450 ft., and the fifth pumped wells at an average of 2100 ft. In 1920, the average production per day from the 32 wells was 325 bbl. The power bill on the

Jan 1, 1928

By P. A. Beck, Hsun Hu

It has been known for many years that in cold drawn polycrystalline aluminum the recrystallization texture is practically identical with the deformation texture.l,2,3 V. Goeler and Sachs4 stated that in cold rolled polycrystalline aluminum, too, the deformation texture is retained upon recrystallization. This behavior was interpreted by Dehlinger9 as an indication that each recrystallized grain inherits the orientation of the matrix in which it grew. However, Burgers and Basart showed6 that in deformed aluminum single crystals the orientation of the recrystallized grains strongly deviates from that of the matrix. Barrett demonstrated8 that even in deformed polycrystalline aggregates the local orientation within each deformed grain changes on recrystallization. No explanation has as yet been offered of how the aggregate texture can be retained, while the local texture is everywhere changing. According to Burgers and Louwerse6 the orientation change on recrystallization in compressed and rolled aluminum single crystals corresponds to a rotation around [112] axes lying in the active slip planes and perpendicular to active slip directions. This orientation change was rationalized by them on the assumption that the orientation of the recrystallized grains is determined by the orientation of the available nuclei, and that these nuclei are small fragments of the deformed crystal, rotated in the deformation process. Barrett pointed out,? however, that these assumptions were by no means proven, and that the total volume of material necessary for the nuclei is so small, that it must be available in any orien- tation whatever. It is, therefore, unlikely that an "oriented nucleation" theory could satisfactorily explain the orientation changes in recrystallization of a deformed crystal. Furthermore, in contradiction to Burgers and LOU-werse's conclusions, Barrett's results for the orientation change could be best expressed in terms of rotations around. [Ill] axes. Thus agreement is lacking not only in the interpretations but apparently even in the experimental results contributed by the various investigators. The orientation relationships on coarsening* in a highly oriented polycrystalline matrix were first investigated by Burgers and Basart.5 They produced a fine grained highly oriented matrix by the recrystallization of a compressed or rolled single crystal of aluminum, and studied the orientation relationships in three successive generations of crystals: the "deformation texture" in the single crystal, the recrystallization texture, and the coarsening texture. Burgers24 showed that the preferred orientation of each successive generation was almost always widely different from that of the preceding one, but that the coarse grains often approximately reverted to the orientation of their grandparent, the deformed single crystal. This observation, and the idea that the orientation of the coarse grains is determined by that of the available "nuclei," led to the concept that the coarse grains are nucleated by the remnants of the deformation texture.12,15 On the other hand, Bowles and Boas16 found, in a carefully conducted experiment, that in recrystallized fine grained copper of cube texture coarse grains grow in orientations which can be derived from the orientation of the recrystallized matrix by rotation around a [lll].] direction: the coarsening texture here does not appear to be related in any simple manner to the original rolling texture from which the cube texture had been obtained by recrystallization. It may be assumed that in a recrystallized material, even with a strong texture, there always are present some grains of practically any orientation. These may serve as "nuclei" for the coarse grains, provided that the conditions are favorable for their growth. The existence of a coarsening texture may be considered as an indication that grains with certain relative orientations with respect to the preferred orientation of their neighbors can grow much faster than others. This "oriented growth" theory was briefly suggested by van Arkel, as early as 1936,13 and it was mentioned by Burgers." Recently, C. G. Dunn produced direct

Jan 1, 1950

By John Norton

THE tremendous increase in the use of metals that have been prepared by the various cold-working processes during recent years has greatly stimulated the investigation of problems concerned with the fundamental nature of these processes. It has been observed in practice that different methods of bringing about the same dimension changes in a sample result in a rather wide range of properties. Cold working reduces the ductility of a metal, or what is perhaps more nearly correct, its "working capacity," and naturally the manufacturer wishes to produce an article that has as large a working capacity as possible, and to produce it with the smallest number of operations, It has also been known for some time that cold deformation produces a parallel alignment of the crystal grains of a metal, and that the type of this preferred orientation depends to some extent at least upon particular processes employed in the deformation. The present investigation has for its purpose the study of the relations between the various factors of a cold-working process and the preferred orientation of the metal crystals resulting from this deformation. The work is chiefly confined to a study of cold-drawn seamless tubing.

Jan 1, 1932

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.'-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

By Will Clark

HE who enters a mining claim within an Indian reservation of the United States of America acquires no rights thereby, because of the fact that the lands within such Indian reservation are not a part of the public domain, and cannot be located or acquired as mineral land. However, where such an entry is authorized as to a particular reservation by an Act of Congress, such claims as may be entered under such authorization are thereby segregated from the reservation, and the Indian title is extinguished. Under the Choctaw Constitution, any citizen of that nation, in other words any Choctaw Indian, who discovered a coal mine, acquired an exclusive right to all coal within a radius of 1 mile. The laws of the Chickasaw nation provided for the formation of corporations to develop coal and other mines, with authority to contract with others to develop and work the mines. Under these laws, leases were made; but Congress subsequently abrogated all existing leases, prohibited all persons from receiving royalties from such mines, and provided that all coal within the nation should remain the common property of the tribes. Such leases are now expressly prohibited by an Act of Congress (32 United States Statutes at Large, 655). All leases of mineral lands upon Indian reservations must now be made under regulations promulgated by the Secretary of the Interior, and the royalties must be paid into the United States Treasury for the benefit of the tribes. In Canada the Indians have no rights to the royal mines and minerals, and the government can make no stipulation with the Indians which would affect the rights of the Province in which the lands are situated. Therefore, while it is true that under our present law no rights can be acquired to a mining claim within an Indian reservation, it seems to be fully within the authority of Congress to make laws, giving such rights to mineral locators as it may deem necessary or expedient.

Jan 6, 1914

By B. C. Allen, W. D. Kingery

Surface tension and its temperature dependence have been determined for pure liquid Fe, Cu, Co, Ni, and Sn and for Fe-C, Co-C, and Ni-C alloys. The temperature coefficient of surface tension is negative for all these liquids. The surface tension and wetting behavior of tin and tin-titanium alloys on A120,, Si,N,, MoSi,, and Sic, as well as the behavior of titanium-containing nickel alloys on A1 20, have been determined over a wide temperature range. For all the solids investigated titanium additims markedly lower the contact angle. Some limits for the solid-surface energies have been calculated from liquid surface tension and wetting behavior. SURFACE tension and interface energy are important variables in a number of metallurgical and ceramic phenomena, and have been discussed at some length in connection with determining micro-structure of polyphase systems,' solid-state sintering,' thermal etching of grain boundaries, heats of solution and fine powders,'1 grain-growth phenomena,' the mechanical behavior of fine foils and fibers, nucleation, soldering and brazing,' and other phenomenz of academic or practical interest However, until recently few quantitative data have been available for high-temperature systems. Among available data are some indicating positive temperature coefficients for the surface tension of liquid copper,*,11,'2 cast iron,l3 and iron-carbon14 alloys. Although carbon was found to be not surface active in iron at 1570" some preliminary studies had indicated the possibility of a positive temperature coefficient for the eutectic composition at lower temperatures.16 One part of the present study has been largely concerned with determining the temperature coefficient of surface tension for several metals at elevated temperatures, In addition to surface-tension studies, the wetting behavior of alloys containing titanium has been investigated over a wide temperature range. Previous measurements indicated that titanium was selectively adsorbed from nickel at a liquid nickel-solid alumina interface,17 and the use of titanium hydride or titanium-alloy techniques for metal-ceramic soldering is well known. In the present study, previous data have been extended to new alloy systems, and measurements have been carried out with other oxidation-resistant ceramics. EXPERIMENTAL The sessile-drop method was employed to measure liquid surface tension and contact angle between liquid and solid, utilizing apparatus and techniques which have been described previously.'g The shape of a sessile drop depends on equilibrium between forces of surface tension tending to form a spherical surface of minimum area and forces of gravity tending to flatten the drop. Typical sessile drops are shown in Fig. 1. From precise measurements of maximum drop diameter and drop height the surface tension and drop volume were calculated. Four solid materials were employed as supporting plaques for the liquid-metal drops. Aluminum oxide (99.9 pct, J, T. Baker, reagent grade) was pressed and sintered at 1800°C. Molybdenum-disilicide powder (99.0 pct, Electro Metallurgical Co.) was pressed and sintered at 1650°C. Plaques were cut from silicon carbide (99.4 pct, hot-pressed at Alfred University) and silicon nitride (95.1 pct, with Al, Fe, 0 as major impurities, Norton Co.) rods. All plaques were polished, cleaned, and dried prior to use. A number of metals and alloys were employed. Chemical analyses of vacuum-melted ingots of iron, nickel, cobalt (National Research Corp.), commercial nickel-base alloys, electrolytic copper (International Smelting and Refining Co.), and tin (Mal-linckrodt Chemical Works) are given in Table I. Alloys were prepared in the laboratory by vacuum melting the base metal with either titanium hydride (Metal Hydrides, Xnc.) or spectroscopic-grade carbon (National Carbon Corp.). Nickel-titanium alloys contained between 0.001 and 0.005 pct oxygen and the ferromagnetic metal-carbon alloys contained 0.001 pct. Cylindrical metal specimens (1 to 2.5 g) were machined and bevelled at the bottom to insure a uniform advancing contact angle on melting. Before use the samples were acid-etched, cleaned with acetone, and rinsed in petrol ether.

Jan 1, 1960

By Douglas A. Sloan

Who would believe that young elementary school children could understand something as complex as the mining industry? The Challenge The challenge of accomplishing this is tremendous. An examination of Canadian school children indicated that they knew very little about the world of work in general, and hardly anything about the mineral resource industry in particular. It calls to mind the story about two youngsters who decided to play house. The little girl played her role well as she went about the house doing things she had watched her mother do every day. When it was the little boy's turn, he grabbed his lunch, waved goodbye to his "wife," jumped on his bicycle and pedalled furiously down to the end of the driveway-where he stopped. The youngster explained that he saw his dad go out of the driveway each morning, but he didn't know where he went, or what he did on the job. When you stop to consider the number of families today with two working parents, you can begin to appreciate the importance of the opportunities for role identity provided by this project. The Approach The challenge of teaching the school children of Canada about the world of work and, specifically, the mining industry is the challenge which the Canadian Institute of Mining and Metallurgy met with the Curriculum Development Research project. It started when a small, dedicated group of Vancouver members met Dr. Doreen Binnington. After this meeting, Dr. Binnington, an expert in curriculum development at the University of British Columbia, set herself to develop a curriculum program for the elementary shcools which accomplishes two main goals: It uses the "Identity Approach," developed by Dr. Binnington, an expert in curriculum development at the enable students to understand and appreciate the contribution of people, in this case, working with mineral resources. It has pupils enthusiastically exploring the importance of rocks, minerals, and the mining industry in their lives [(Fig. 1)]. Evolution of the Curriculum Development Research Project When the curriculum development research project was presented to the Vancouver Branch of the Canadian Institute of

Jan 1, 1981

By Charles T. Malcomson

In the United States, improvements in methods of combustion have made possible the use of the smaller sizes of anthracite. This coal is now being reclaimed from the culm banks accumulated by the miners in the more prodigal years. To-day the freshly mined "slush" is segrega,ted and stored against the time when, through briquetting or some other means, it may be utilized as a commercial fuel. For many years Europe has achieved enviable results in the conservation of her small coal by briquetting. This profitable industry, first placed on a commercial basis in France in 1842, has grown to such magnitude that the production during 1913 exceeded 36,000,000 short tons. Briquets produced in Great Britain are used principally for steam purposes and the greater part of the output is either exported or taken by the Admiralty. On the Continent the briquets are sold in all branches of the coal trade. The French railways consume from 16 to 40 per cent. of their fuel in briquet form, and in Germany the lignite briquets (of which 20,000,000 tons were produced in 1913) are as familiar and interesting to the American traveler as the huge porcelain stoves in which they are burned. It is not strange, therefore, that aggressive and far-sighted promoters heralded this means of converting our ubiquitous coal waste into revenue. To the superficial student the briquetting process seemed so simple as to make success easy. It is for this reason principally that the path of the industry in America has been strewn with failures. The rash enthusiast had either not worked out the mechanical problems involved or had failed to grasp the local conditions under which the briquets must be made and sold. It may be confidently stated, however, that in spite of the many vicissitudes through which it has passed, coal briquetting is now an accomplished economic success in this country, and as a profitable adjunct to the coal industry it has come to stay. Several valuable contributions relating to coal briquetting are found in the Transactions. Charles Dorrance, Jr., has sketched briefly the history of the anthracite briquetting plants from the time of Loiseau's pioneer plant down to that of the Lehigh Coal & Navigation Co. at Lans-ford. Since then this phase of the industry has remained practically at

Jan 1, 1915

By Ivan E. Goodner, Charles H. Fulton

The subject of the constitution of copper-iron mattes has received considerable attention in recent years by Keller,' Belles,2 Hofman,3 and Gibb and Philp.4 Still more recently Friedrich, Röntgen, Wiedmann, Heyn and Bauer, and Leroux have published, in some instances, elaborate researches on the various systems of the sulphides, and the snlphides and their respective metals, which enter into the constitution of mattes, and have added very greatly to the knowledge of the subject. The work of Friedrich has been especially fruitful. But to' date no effort has been made to correlate the data obtained in the latter researches and apply them to the study of the product called " matte," which is made in such large quantities by copper- and lead-smelters. In this paper we propose to determine, by metallographic and chemical means, the constitution of copper-iron and copper-lead-iron mattes in the light of the recent data above mentioned. We do not discuss copper-nickel mattes or speisses (artificial arsenides). The paper is divided into three sections: I. A review and discussion of the various binary systems of the metallic sulphides, and the binary systems of various metals and their respective sulphides entering into the constitution of mattes; also a discussion of the physical properties of these sulphides. II. A description of the results obtained from the chemical and microscopic examinations of the samples of copper-iron and copper-lead-iron matte obtained from various plants.

Jan 1, 1909

By J. D. Price, G. V. Woody

MANY producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. OVERCOMING DEFECTS IN COKE FROM COLORADO COALS Colorado coking coals are all of the high-volatile type and were all laid down during he Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Pocahontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-volatile coal was developed through low-temperature carbonization-or, more correctly speaking, through the partial devolatilization-of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

By Alfonso W. Ovalle

INTRODUCTION The block-caving mining method is one of the most economical ways existing today to extract ore from nature. It is undoubtedly the least costly of the underground systems and moreover it compares favorably to open-pit mining. In addition to its low cost characteristic, the block-caving mining method permits a great extraction volume as can be exemplified by El Teniente's output capacity of over 22 million tons of ore per year. These characteristics of block-caving give assurance that, even though it is a very old mining system, it will be a good answer to the many future large massive low ore grade deposits to come and a1 so to rep1 ace open-pi t mining as such operations get deeper with higher stripping ratios. These are the reasons that induce further study of block-caving. In this paper block-caving at El Teniente is analyzed with due consideration to the major problems that this mine will encounter. Emphasis is given to the factors influencing the mining of soft ore which accounts for most of the ore to be extracted in the next ten years. A separate paper is devoted to a major modification introduced to block-caving hard primary ore at El Teniente by means of LHD equipment extraction. DESCRIPTION OF THE PRESENT MINING Ore Production and Flow Over 62.000 tons per day of ore are extracted 359 days per year at the El Teniente Mine. The Teniente 8 train haulage level at 1.983 m takes 29.000 tons daily to the Col6n Concentrator. Two trains make the 8 km haul with 16 cars per train. Car capacity is 90 tons. The Teniente 5 train haulage level 298 m above takes 33.000 t per day to the old Sewell Concentrator. Ore is produced from three production areas in two different levels. The so called North Mine produces 42.000 tons daily from the Teniente 4 level 65 m above the Teniente 5 haulage level. The Central Mine produces 1.000 tons from the first hard rock block caved at the Te- niente 4 level. The combined 43.000 tons per day production is sent through inclined 2 m dia- meter raises to the Teniente 5 haul age level , where 33.000 tons are taken 2.5 km to the Sewell Concentrator and 9.000 tons are hauled 0.5 km to a 5 m diameter vertical ore pass which sends ore to Teniente 8. The haulage is by 7 trains, 15 gabble-bottom cars per train. Car capacity is 20 tons. The so called South Mine produces 19.000 tons per day from the Teniente 1 level 645 m above the Teniente 8 haulage level. Ore is transferred by 2 m diameter inclined raises to the Ten 1 Retram level 22 m below, where 5 trains with 20 Sandfor Day cars per train, 8 tons capacity per car, haul the ore 1.5 km to two vertical 5 m diameter ore passes which connect to Ten 8. Starting in 1982 the Central Mine will in- crease production to 6.000 tons per day. An in- dependent loop haulage system will start operat- ing at the Teniente 5 level to feed a new under- ground 1.372 mm (54 in.) gyratory crusher which will send minus 152 mm ore (9 in.) to Teniente 8. In two or three years time the North Mine will only feed the 33.000 tons to the Sewel 1 Concentrator with its old Teniente 5 haulage system. The Col6n Concentrator will be fed from the Central and South Mines. Figure 1 shows the transfer systems and ore flows. The Ore Body In plan view at the Teniente 4 level the ore body has a kidney shape 1.800 m long and between 400 to 700 m wide. The north-eastern section of the ore body was washed away by the Teniente River. At the Sub 5 Level, 125 m below Teniente 4, the mineralization completely surrounds the circular 1.000 m diameter steep-sided barren breccia pipe (Braden pipe) . The ore body rock is 73% andesite, 14% diori te, 13% dacite and 6% mineralized breccia. Most of this ore is secondary enrichment sulfides which apart from the dacite is strongly fractured being chal cocite, cove1ine , bornite and

Jan 1, 1981

By Andrew Hyslop

IN our never ending search for new and better ways of underground mining, we find that transportation has had its share of new ideas in the past few years. The old and still effective method of track haulage has had some competition from rubber tired cars and belt conveyors, each of which has its own safety hazards which demand close scrutiny in any safety study. The use of shuttle cars, in particular, has introduced clearance hazards caused by the absence of the more or less positive guides formed by the rails of a track sys¬tem; likewise the requirement of greater clearance tends to increase roof hazards which we all know to be great enough with the best of methods. However, the subject of transportation hazards is too broad to be covered entirely in one paper, so I will confine myself to track methods which carry the preponderance of underground tonnage. I am quite sure that to this group it is an evident fact that haulage accidents are of major importance. However, to stress the point, it may be well to look at a few figures. Safety statistics can be quite boring and often are subject to question as to mathematical accuracy because of different

Jan 1, 1948

By John H. Walthall, Raymond L. Copson, Travis P. Hignett

In October 1942, the War Production Board requested the Tennessee Valley Authority to undertake investigations to determine the feasibility of producing alumina suitable for reduction in aluminum cells, from clays and other domestic materials, by a lime-sintering, soda-ash leaching process. The work was undertaken by the chemical engineering staff of the Authority under the general direction of the War Metallurgy Committee of the National Academy of Sciences. The investigation included small-scale tests to determine the most suitable conditions for the process, and construction and operation of a pilot plant to obtain data for evaluation of the process and for design of a plant. The results of this investigation are described in the present paper. Sources of Alumina Alumina for the commercial production of aluminum is obtained from bauxite by the Bayer process. The tremendous demand for aluminum for wartime uses is causing rapid exhaustion of the high-grade bauxite deposits in the United States. On the other hand, there is an abundance of aluminous materials such as clay and lower grades of bauxite, which are not suitable for treatment by the Bayer process because of their high silica content. The Tennessee Valley Authority has conducted research and pilot-plant work for more than 5 years on methods for the production of alumina from clay and low-grade bauxite. Particular attention has been given to the high-grade white kaolin found in Carroll County, Tennessee. Exploratory drilling has demonstrated that at least 4 1/2 million tons of kaolin containing in excess of 34 per cent AlzOI is available in this area by strip-mining methods. It has been estimated that hundreds of millions of tons of clay of similar quality occur in the Tennessee Valley region. The Process The process is illustrated in the flowsheet (Fig. I), and consists essentially of the following steps: I. Heating a mixture of clay and limestone to form a sinter containing calcium aluminate and dicalcium silicate. z. Leaching this sinter with a dilute sodium carbonate solution, to form a sodium aluminate solution and a calcium carbonate, calcium silicate residue, which is discarded. 3. Treating the sodium aluminate solution with carbon dioxide to precipitate aluminum trihydrate and regenerate the sodium carbonate solution, which is recycled. 4. Heating the aluminum trihydrate to produce alumina. The process was considered promising because of the abundance and cheapness of the two raw materials, clay and limestone; and because, as compared with an acid process, smaller amounts of critical

Jan 1, 1944

By R. R. McNaughton

The Consolidated Mining and Smelting Company of Canada, Ltd. at Trail, B. C., inaugurated a comprehensive program of investigation about 15 years ago to develop the most economical process of recovering the metal in the large accumulated stock of by-products of the lead smelter and the zinc plant. Two principal methods of recovery were followed to a successful conclusion—an electrothermic process to treat zinc-plant residues and cold slag and the fuming of hot slag from the lead blast furnaces. The latter was selected because it showed a saving over the former in its ability to handle hot blast-furnace slag, thus obviating the necessity of granulating, handling and eventually remelting the same slag for the electrothermic process. The design of a fuming plant was commenced in 1928, and construction, which was started immediately, was completed in July 1030. Operating intermittently for a general tuning up, the plant was officially blown in for regular operation in August. During this month the vagaries of a slag-fuming plant were studied and an operating crew was trained. A history of slag fuming at Trail and the development of plant design is given in a paper by G. E. Murray in the Transactions of the Canadian Institute of Mining and Metallurgy for 1933. Fuming Plant The fuming plant at Trail (Fig. 1) is a separate unit although of necessity interlocked closely with the lead smelter. The plant consists essentially of a fuming furnace with its accessories, a waste-heat boiler followed by an economizer, and a suction-type baghouse. The plant was built as the first of two 400-ton units with the intention of adding the second unit within a year, so that flues, fans and buildings were built to handle double the original load. Furnace.—The furnace as originally built (Fig. 2) was of water-jacket construction, 10 ft. wide, 20 ft. long and 6 to 10 ft. high. The roof height was made variable to check experimental work, which had indicated that this dimension affected the rate of reduction. Coal and air were supplied

Jan 1, 1937

By Rudolph G. Wuerker

MUCH descriptive matter[ ] has appeared on the subject of suspension roof supports, or roof bolting, as it is more commonly called. The wide- spread introduction of roof bolting into coal mines and metal mines is truly phenomenal. Mine operators were quick to recognize the advantages of supporting wide openings without hindrance to machine maneuverability and ventilation.

Jan 6, 1953

By M. L. Brashears

IN the last 15 years industrial use of ground water has more than doubled, and in 1951 amounted to 5 billion gallons per day. A similar sharp increase in the utilization of ground water for irrigation and public-water supply occurred in the same period. In many areas rapid increase in withdrawal from wells has taken place almost entirely unhampered by regulatory control and with little or no integration of effort. As might be expected, the chief interest in many regions has been maximum production rather than sustained perennial yield. As a result, widespread depletion of underground reservoirs and deterioration of the quality of the water stored in them has taken place in many areas, even though total pumpage in the United States is far below ultimate potential. Of even more concern is the fact that excessive withdrawal has drawn salt water into the reservoirs beneath many heavily populated centers along the Atlantic, Gulf, and Pacific coasts, causing costly abandonment of pumping plants.' Many hydrologists expect that consumption of water will rise rapidly in the near future, and some predict that industrial requirements will more than double in the next decade.2,3 Thus it appears likely that the draft on many already heavily pumped underground reservoirs will be greatly increased and the search for additional sources of usable ground water intensified in years to come. In view of this, industry as a whole will be forced more and more to recognize the potentialities and limitations of ground-water reservoirs and to utilize them more effectively to prevent costly water shortages and disruption of production. Through painful experience, some industries are already well aware of the need for effective water utilization, and have managed individually or through joint effort to check trends threatening to deplete underground reservoirs completely or to impair the quality of the water. Various remedial measures have been used to bring about successful management of local or regional ground-water resources. Of these, replen-ishment of aquifers by recharge wells or basins has played an important role in overcoming some ground water problems. Artificial recharge of underground reservoirs by water spreading has been practiced successfully in the United States for many years. In the West it has become an important method of salvaging flood run-off for irrigation of crops and maintenance of public water-supply reserves, and it is used to some extent in parts of the East. Artificial recharge by means of wells, on the other hand, is a relatively new development. Until recently it was employed in only a few areas, principally along the East coast. For the last few years, in the ever increasing search for additional water supplies, industry has had greater recourse to this method. Utilization of recharge wells to control the temperature and quality of underground water supplies is also being considered seriously. Operation of recharge wells, like water spreading, is governed largely by local conditions. It requires water relatively low in turbidity, whereas in some areas water spreading has been used successfully with water of high turbidity and silt content. However, water spreading must be employed in large areas and can be carried on effectively only where aquifers crop out at the surface. Recharge wells can be used in limited space. Recharge wells are similar to production wells except that the water flows in the opposite direction. Thus any water-bearing bed that will yield water to wells may be recharged by wells. Often, however, the water available for recharge is of a different character and temperature from that existing in the ground-water reservoir and if transmitted directly underground from a recharge well to a production well might require expensive or difficult treatment before it could be used. Fortunately the physical characteristics of reservoir beds, which control the movement and behavior of ground water, are generally not homogeneous. Moreover, the movement of ground water is very slow because of the frictional resistance of the reservoir beds. By taking full advantage of hydrologic and geologic conditions, it is therefore possible in many instances to bring about favorable changes of temperature and dilution as the water moves from the recharge wells underground to the production wells. Furthermore, if the natural quality or temperature of ground water is unfavorable for industrial purposes, recharge wells may be used to introduce water of more favorable quality or temperature into the ground-water reservoir. When water is discharged into a recharge well, the head in the well is increased. Because of this, a cone of elevation is produced on the water table or the artesian pressure surface in the area surrounding the well. The cone of elevation is similar to the cone of depression produced around a pumping well except that the apex of the cone is above the water table or artesian pressure surface. Thus if a recharge well and a production well tapping the same water-bearing bed are close together, as would be the case at many industrial plants, some of the water discharged from the recharge well would be drawn into the production well within a short time. Under such conditions it is apparent that water of unfavorable temperature and chemical characteristics should not be used for recharging. The more important ground-water reservoirs in the United States often consist of alternating layers of impermeable beds and porous material that will yield water readily to wells. Physical characteristics of individual beds in a ground-water reservoir may not persist over great distances, the impermeable layers grading into beds that will yield large quantities of water. Thus the water-yielding material in underground reservoirs, whether large or small,

Jan 1, 1954

By Yoon T. Auck, Milton E. Wadsworth

Column leach studies of two low grade prophyry copper ores were made with variables of size, flow rate, pH, drainage rate and tempature. Evidence is presented to show that, in some types of ores, sulfide minerals block leaching channels and regulate the rate of dissolution of gangue constituents. Basic iron sulfates, dissolved by introducing acid, provide oxidizing agent in the form of ferric ion in the absence of oxygen. Ferric ion then acts to release copper from the ore. Oxygen up-take was found to increase with the lowering of the pH and to follow parabolic kinetics attributable to the precipitation of basic iron salts within the pore channels. Slow drainage of residual gravitational water can seriously retard oxygen up-take during oxidation for particles in the coarse sand range. A model is presented for dump leaching in which a reaction zone connected by channels to the surface of the ore particle moves topo-chemically during the course of the reaction.

Jan 1, 1973

By E. Cortese

Phosphate occurs in many places in Egypt, in two main zones: one in Upper Egypt, along the Nile Valley, principally on the right side, and one near the Red Sea coast. In the Nile zone, the principal layers of phosphate rock are to be found: in the mountains east of Mahamid (right side of the valley); in the hills near Sibaiya, also called Sebaieh (both sides); in the hills of Agula, Hagaza and Gurn (right side); and further on, along the camel road leading from Kena to Kosseir, a few miles east of Legheita's Oasis. Following that track, after having crossed the watershed, underlain by rocks like granite, serpentine, porphyry, and diabase, one comes again to the Cretaceous formation containing considerable quantities of phosphate, at Gebel Duwi, Gebel Nakheil, and Gebel Kosseir El Kadim, not far from the coast. More to the north, in the hills near Safaga Bay (Um El Uettat El Wasif) is another rich bed of the same formation. There are reports of phosphate existing near Suez and in the Sinai peninsula, and possibly some other zones can be traced or discovered in the future. The mines are well developed on the right bank of the Nile at Sharawna (near Sebaieh Station) and along the Red Sea coast, at Safaga and near Kosseir. Prospecting work has been done at Gebel Duwi, Gebel Gurn, Agula, Hagaza, and near Mahamid. The phosphatic formation in Egypt is quite variable, not only from place to place, but even within small areas. The phosphate is all of Cretaceous age, as is proved by the fossils found in it. It is considered to belong to the Campanian or, more appropriately, to the Maestrichtian series. The principal fossils are: Alectryonia Villei Coq. sp.; Roudereia Aures-sensis Coq. sp. = R. Drui Mun. Chalm.; Trigonoarca multidentata, Newton.; Cardita libyca, Zittel; Libycoceras Ismaely, Zittel; Nautilus sp.; Ancystrodon libycum Dam.; Corax pristodontus Ag.; Lamma biauriculata Zittel sp. Above the Maestrichtian beds, we have the Danian series, unconform-ably covered by Lower Eocene beds. Under the phosphate is a grayish marly clay, and beneath this, bluish-gray scaly shales resting on the Nubian sandstone (Santonian).

Jan 1, 1918

By C. N. J. Wagner, E. N. Aqua

The bee alloys of the terminal solid solution of rhenium in niobium were investigated by X-ray diffraclion methods. The analysis of the broadening of the powder pattern peaks from the niobium-rich alloys, cold-worked by filing, showed evidence for faulting on (211) planes. The alloys with larger rhenium concentrations were brittle, and fractured when filed. The analysis of the shapes of the diffraction profiles from powders produced by hammering with steel plates) of these brittle alloys indicated that the broadening was due predominantly to platelets bounded by clibe planes. This result was consistent with the Laue patterns from single-cleazlage facets which showed evidence for clearage fracture on {100} planes. The influence of faulting on the mechanical properties of face-centered cubic (fcc) metals and alloys, i.e., how faulting affects the various dislocation configurations in fcc metals, is well-known.' The important question is whether or not faulting occurs in body-centered cubic (bcc) metals and alloys, and, furthermore, if faulting does occur, to what extent it affects the mechanical properties. Theoretical calculations indicate that the stacking-fault energy is rather high in most bcc metals.2 The results of sev-eral studies using transmission electron microscopy have indicated that faults are present in well-annealed and lightly deformed bcc metals and alloys, such as tungsten,3 vanadium,4 and Mo-Re alloys.5,6 These faults, as have been observed, may be stabilized by the presence of interstitial (C,N,O) atom segregation to the extended dislocations. In addition, there is considerable X-ray diffraction evidence for faulting in bee metals,7-8 using the same techniques that were successful for the study of faulting in fee metals and alloys.7 This X-ray diffraction method is currently the only technique applicable for the investigation of faulting in metals with high stacking fault energies, i.e., when severe amounts of deformation are required to produce sufficient amounts of faulting to be detectable by X-rays. The thinned films of heavily deformed metals will become opaque in the electron microscope due to the high dislocation densities present. In a previous investigation of faulting8 in bee metals of group Vb and VIb, the authors observed that niobium was ductile when filed at room temperature, and showed the highest density of faults on the (112) family of planes. A niobium-base alloy system was therefore chosen to study the effect of alloying on the occurrence of faults in a bcc alloy. There is a large range of terminal solid solubility of rhenium in the alloys of the bee refractory metals. All of the Group VIb-rhenium alloys, i.e., Cr-Re, Mo-Re, and W-Re, exhibit solid solution hardening without loss of ductility.9 In fact, the ductility reaches a maximum for alloys with compositions near to the limits of solubility. This enhanced ductility has been attributed to the lowering of the stacking-fault energy in the alloy; i.e., the increased amounts of twinning provide an additional mode of deformation, resulting in the observed high ductility.' Because of this demonstrated effect of rhenium in bee alloys, it was decided to study a series of alloys of Nb-Re. Using the same X-ray diffraction methods as described in the previous investigation,' one is able to identify the possible causes of broadening of the powder pattern peaks, e.q., particle size, microstrains, stacking faults, and/or twin faults. The separation of these various contributions to the measured peak shape is accomplished by the Warren-Averbach analysis.7 I) EXPERIMENTAL PROCEDURE A series of seven bee solid solution alloys containing from 2.5 to 21.5 at. pct Re (remainder niobium) were prepared at the General Electric Research Laboratory. Buttons, weighing 25 g, were alloyed from electron-beam-melted niobium chips and random rhenium sheet by arc melting in a water-cooled copper crucible, under an argon atmosphere. The buttons were inverted and completely remelted to promote homogenization. The nominal alloy compositions are listed in Table I. Samples of the cold-worked alloys were obtained by filing to produce a powder for the X-ray study. Alloys too brittle to be filed were hammered with steel plates. The resultant filings or brittle impactings were screened through 150-mesh classifiers and compacted to the required shape for the diffractometer holder. The X-ray diffraction peaks were automatically recorded by fixed time counting at uniform 28 intervals, or by continuous registration with a ratemeter. In all cases, the (110)-(220) and (200)-(400) pairs of peaks and the (211), (310), (222), and (321) reflections were measured on a GE-XRD5 diffractometer using CuKa radiation with nickel filter or MoKct radiation and a LiF monochromator in the diffracted beam. The first part of the data reduction, completed with the aid of a series of programmed computations,10 was the analytical resolution of the Kol component of the diffraction profile. Subsequent computations were then made with reference only to the resolved Kol peak shape. These included the measurement of the

Jan 1, 1967

President H. M. Howe, Boston, Mass. (communication to the Secretary): Le Chatelier's pyrometer is certainly a most convenient and accurate instrument for the laboratory, and one that may be used under some conditions in the mill. I have used it for several years and with great satisfaction. Like Prof. Roberts-Austen and unlike Herr Blass, I have always found that its indications remain constant over long periods. Like Prof. Roberts-Austen, also, I find it possible, in a quiet place, to read with extreme accuracy ; and, by the use of a telescope, I can read temperatures to within a degree, for some delicate determinations which I have in hand. Variations in the temperature of the room affect the readings of the instrument far less than one would expect. When the current is cut off, the mirror does not always return exactly to the same place; in other words, the zero shifts appreciably, and must be determined often, indeed every few hours if accuracy be desired. In some cases I have had it determined within a very few minutes of every important reading. To this end a switch should he introduced, so that the circuit may be broken readily. With this arrangement we can determine accurately the position of the zero within a very few seconds of the time of taking any especially important reading. The chief causes of the variation of the zero which I have noticed are as follows: a. The suspension may not be tight enough, so that the momentum of the galvanometer frame as it swings makes its supporting wires slip in their bearings. b. Changes in the position of neighboring iron objects may deflect the mirror. c. Changes in the temperature of the room may, perhaps, change the torsion of the suspension wires, and so shift the mirror. d. Dust may attach itself to the galvanometer frame, and by friction against the surrounding fixed parts of the galvanometer, may

Jan 1, 1895