Search Documents

By T. L. Loucks, E. T. Guerrero

Pressure drop characteristics in a system composed of two adjacent concentric regions of different permeability were studied. The differential equations for continuity of mass flow in the two regions were solved using the Laplace transformation and the necessary boundary conditions to give the pressure distribution in the composite reservoir, the resulting equation for pressure drop at the inner boundary was evaluated for a variety of composite reservoirs and compared with the results for a uniform reservoir. From this study it was found that under certain conditions the permeability in both zones, as well as the size of the inner zone, can be determined from the pressure drop curve. INTRODUCTION The theory for the pressure distribution and pressure build-up behavior of a well producing a single, slightly compressible fluid from infinite and finite homogeneous reservoirs was presented by Hornerl and Miller, Dyes and Hutchinson.2 Extensions on this original work to provide improved and extended interpretations and better agreement between theory and observed results have been made by Matthews, et a1,3 van Everdingen,4 Gladfelter, et al5 Stegemeierand Matthews,6 Hurst and Guerrero,7 and Perrine.8 More recently Lefkovits, et al,9 studied pressure build-up behavior in bounded reservoirs composed of stratified layers. Houpeurtl0 has suggested various approaches to the general problem of variable permeability and porosity but presented no analytic solutions for particular permeability variations. Albert, Jaisson and Marionll studied the finite composite reservoir and presented numerical solutions to the unsteady-state case and an analytical solution valid only for large times. They also studied the so-called pseudo-steady state for several examples of radial permeability variations. Very similar examples have been treated in the unsteady state with application to pressure build-up by Loucks in an unpublished manuscript. More recently Hurst12 has presented the complete point-sink solution (valid for all times) for the infinite composite reservoir. He applied these solutions to interference between oil fields along with an even more elegant application of his explicit solution to the material-balance equation including water influx. Mortada 13 approaches the same application by avoiding the point-source limitation but gives the solution for the aquifer region which is valid only for large times. Hopkinson, Natanson and Temple14 have treated both the finite and infinite composite reservoir obtaining the pressure distribution for the inner zone valid for large times. This paper presents a theoretical study of the pressure distribution in an infinite composite reservoir composed of two adjacent concentric regions of different permeability. The object was to determine the manner in which pressure drop at the inner boundary of a composite reservoir depends upon time, the permeability of each zone and the size of the inner zone. Expressions for the pressure distribution in both zones are developed which take into account the radius of the sink and are valid for small times as well as large times. It was felt that an understanding of the pressure drop behavior in various composite reservoirs would be of assistance in the interpretation of some pressure build-up curves which do not behave according to the theory derived for uniform systems. Often the region surrounding the wellbore is either more permeable or less permeable than the reservoir because of the various drilling and completion practices. The effects of reduced permeability due to drilling-fluid invasion and of increased permeability due to fracturing or acidizing need to be more carefully defined. Therefore, an equation for the pressure drop in a composite reservoir was developed, and the effects of both the permeability in each zone and the size of the inner zone were studied. STATEMENT AND SOLUTION OF PROBLEM BOUNDARY CONDITIONS AND ASSUMPTIONS The physical system studied was a composite

THE Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties situated at 29 West 39th Street in New York City.

Jan 1, 1946

By Thomas M. Drown

The process for determining phosphorus in iron now in most general use in the laboratories of iron and steel works, is, I think, the one proposed bv Mr. Emmerton." In this process the solution of the iron for precipitation by ammonium molybdate is effected by treating the iron with nitric acid, evaporating to hard dryness in a dish, taking up with hydrochloric acid and driving off the greater portion of the hydrochloric by nitric acid. This procedure accomplishes, first, the destruction of all the carbonaceous matters; and, second; it renders all the silica insoluble. Experience has proved the former—the complete oxidation of the carbon—to be absolutely essential; but the explanation usually given, namely, that unless the carbon compounds are destroyed they will have a solvent action on the yellow precipitate, I am inclined to

Jan 1, 1890

By Eric Jette

THE unusual physical, electrical and magnetic properties of the iron-nickel alloys has given rise to a voluminous literature. This work will be reviewed critically in "The Alloys of Iron and Nickel," a monograph of the Alloys of Iron Research Series, soon to be published. In what follows we shall therefore confine ourselves to those of the earlier investi-gations that involved the use of X-ray crystal-structure methods. The earliest X-ray work on the iron-nickel system was by Miss Andrews1. Using the powder method of X-ray analysis purely as a means of identifying the phases present, she located a region between 20 and 30 weight per cent nickel in which body-centered and face-centered phases coexisted. No lattice constants nor details of heat-treat-ment were reported. Bain2 also reported some qualitative observations. McKeehan3 made a systematic investigation over the whole of the system, giving many of his alloys four and some five different heat-treatments. In alloys furnace-cooled from 900° to 950° C. he found two coexisting phases between 0.15 and 30 per cent nickel. The precision of the lattice-constant measurements was low in comparison with what can be obtained today.. Even for alloys of the same heat-treatment, differences in the constants were often between two and ten parts per thousand. In regions where no change of lattice constant with heat-treatment should occur, differences of the same order of magnitude were found. Since the maximum change in the lattice constant of nickel with change of composition is only about 2 per cent of the constant for pure nickel, these variations in the constants for a given alloy cause the points

Jan 1, 1936

By George K. Burgess, Robert A. Hadfield

1. Introduction.—The methods of production of sound steel ingots have been described in several papers read recently before this Institute. It was thought by Director Stratton, of the U. S. Bureau of Standards, and ourselves to be of sufficient interest and importance, as a further contribution to this subject, to compare the properties of rails rolled in one mill according to American practice, from several types of ingot of substantially the same chemical composition but cast by several processes; and to compare in considerable detail the properties of an ingot manufactured by the Hadfield special-feeding process and one of the usual type for rolling into rails. We are greatly indebted to F. W. Wood, President of the Maryland Steel CO., who made this investigation possible by kindly placing his rail mill at our disposal; and he and his associates at Sparrows Point did everything possible to make the experiment a success, including the execution of several of the tests and analyses. 2. Classification and Manufacture of Ingots.—Of the ingots used in this investigation, eight were made in Sheffield and furnished by Sir Robert Hadfield, and one was made and furnished by an American steel company,l as a comparison ingot, and was supposed to represent the usual type of ingot from which rails are made. The characteristics of the ingots are given in Table I. Ingots 1, 2, 3, and 4 were cast large end up and fed by the Hadfield method in the usual manner with charcoal and blast continued until the molten steel has set on the top of the head, say varying from 20 to 40 min. To ingots 1, 2, and 4 was added 0.1 per cent. aluminum, and to the nickel-chrome ingot, No. 3, 0.125 per cent. For sake of comparison, there were also included two ingots, Nos. 8 and 9, cast with the small end up and fed by

Jan 1, 1915

By J. W. Hickman, E. A. Gulbransen

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By Leon W. Dupuy

Many articles have been written describing peculiar and particular types of drilling. Little correlation has been made between the character of ground to be drilled and sampled and the type of drilling most desirable for procuring satisfactory samples. In development work, the engineer and metallurgist often desire the recovery of a sample in as physically natural a condition as possible, particularly when the sample must provide material for process tests as well as chemical and physical analyses. This paper describes the results of experimentation in drilling unconsoli-dated materials carrying titanium minerals in the Magnet Cove area, Ark. The drilling was most difficult in that the ground varied much in consistency, and it was vitally necessary to recover a physically natural sample. Ordinary churn drilling recovered a sample that could be analyzed chemically, but the sample was not in its natural state. The problem was successfully solved by utilizing and further developing methods used in the oil and clay industries. In the Magnet Cove area of Hot Spring County, Ark., the titanium minerals include rutile, brookite, ana- tase, leucoxene, and others. They occur in soil, clays, and altered rocks adjacent to novaculite in contact meta-morphic deposits. In preparing titanium minerals for use in the industry, it is necessary to know the physical characteristics of the ore. Also it is believed that the particular physical character of the titanium mineral used is just as important as the chemical character. Brookite and rutile, for example, are the same chemically but differ in crystalline structure. In preparing titanium minerals for market, beneficia-tion is necessary. For the millman to make a satisfactory laboratory test, the sample he uses must be as nearly of the same physical character as he would have from mine run ore. In the past at Magnet Cove, churn drilling had been done on the properties, and assays of total titania had been obtained. It was found, however, that the total titania was indicative merely of the presence of titania but did not tell the metallurgist the character of the material or even give him the slightest indication of what he might expect to recover. When the Bureau of Mines entered the field in the winter of 1947 and 1948, it was therefore necessary that a natural sample be recovered. LIMITATlONS IN ORDINARY PRACTICE The churn drilling that had previously been done had shown that the occurrence of titanium-bearing mineral was somewhat widespread. The samples were, however, completely beaten up and in a finely powdered state. The minerals had been slimed, and such ore dressing tests as were made from the churn-drill samples were found to be worthless. Test pitting and outcrop sampling had provided satisfactory samples of surface ore but did not represent the entire ore body. A quantity of rutile had been produced from the surface residual concentrations in the westerly part of the cove, but production ran into metallurgical trouble as depth was attained. Representative deep samples upon which ore dressing research might depend were needed.

Jan 1, 1950

By Zay Jeffries

TUNGSTEN has the highest melting point of all the known metals, namely 3350° C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely. brittle and fragile at room temperature, and when possessing a fibrous structure it maybe ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and. ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given.

Jan 6, 1918

By Ford R. Bryan, Edward F. Runge

BECAUSE of the need for ductile heat resistant alloys of non-strategic composition, there has been metallurgical development of Fe-A1 alloys possessing improved ductility and hot strength, together with high oxidation resistance. Iron and alu- minum form solid solutions up to approximately 35 pct Al. Alloys in the 8 to 12 pct A1 range are characterized by excellent oxidation resistance, high electrical resistivity' and, when appropriately alloyed, have creep rupture strength equivalent to that of the austenitic stainless steels.' At higher aluminum levels, the magnetic properties are of considerable interest. Nachman and Buehler" have recently reported on the desirable magnetic characteristics of the 16 pct alloy.

Jan 1, 1957

This is a most interesting paper and some data in it are corroborated by work I did at Watertown Arsenal some time ago with iron powder. I would like to ask Dr. Wulff to say just a little more about the compressive and tensile stresses on the surface of compacts. JOHN WULFF (author's reply).-Our work has not yet been completed; although enough data have been obtained with cylindrical compacts of iron to permit some conclusions. Briefly, in a compact 3/4 in. high and 1/2 in. in diameter pressed at 48 tons per sq. in., the residual stresses on the surface measured by X-ray diffraction techniques are as follows: The radial stresses on top center and bottom of compacts are practically zero; the longitudinal residual stresses on the side walls are near the top quarter of the compact about seven tenths that of the yield point of mild steel in tension; at the center surface of the compact they are in compression and in magnitude about 0.3 that of mild steel in tension; near the bottom, they are practically zero. F. V. LENEL.?- I was particularly interested in the work that Messrs. Wulff and Seelig reported on the influence of lubrication on the density of parts. In connection with the work of the American Society for Testing Materials on determining the green density of a compact, we ran into considerable difficulty in getting reproducible results of green density determinations. It was much easier to get a reproducible green density when the lubricant was mixed with the powder than when the lubricant was applied to the die walls; particularly when the die was not perfect-i.e., if it was somewhat rough or out of round. In this case, it was almost impossible to get reproducible green densities when the die walls were lubricated, while it was not too difficult to get reproducible

Jan 1, 1946

By E. C. W. Perryman

The recovery of X-ray line broadening, hardness, and electrical resistivity from cold worked AI-Mg alloys has been investigated. The results, together with those from density measurements, suggest that magnesium atoms freeze in the excess vacancies formed by cold working, and that this affects the climb of dislocations during the recovery process. PREVIOUS work1, " has shown that while 1 pct Mg increases the activation energy for recrystalliza-tion, it decreases the activation energy for the recovery of mechanical properties and decreases the subgrain size both after cold working and annealing. A similar result has been reported by Varley2 for an A1-2 pct Mg alloy. With plastic deformation at high temperatures, McLean and Farmer' and Rachinger have found that magnesium appears to retard the motion of dislocations and, furthermore, they find little or no effect of magnesium on the size of subgrains formed during high temperature deformation. In view of the apparent contradictions as to the effect of magnesium on subgrain size, the recovery process in Al-Mg alloys has been investigated more thoroughly by studying the annealing out of X-ray line broadening, hardness, and electrical resistivity from alloys cold worked at room temperature. Material Used—The chemical analyses of the alloys are given in Table I. Fabrication—The material used was cold rolled 20 pct at room temperature, the grain size prior to the last cold rolling operation being similar to that used in previous work; i.e., 230. The experimental procedure for annealing, determination of X-rav half-veak breadth. hardness measurement, electEica1 resistivity, and density and metallographic examination was exactly the same as previously described." Variation of X-Ray Half-Peak Breadth with Annealing Time—Isothermal annealing curves at 100°, 200°, and 250°C were obtained for material cold worked 20 pct. The half-peak breadth of the (333) Ka, line directly after cold working is shown as a function of magnesium content in Fig. 1. Only with the 2.87 pct Mg alloy was overlapping of the a, and n.. reflections observed to any appreciable extent. To separate these, Rachinger's method' was used. Typical isothermal annealing curves are shown in Figs. 2 and 3 for 100" and 200°C, respectively. These curves are similar to those obtained previously for super-purity aluminum except that the

Jan 1, 1957

By Walter J. Karplus

By means of a finite difference expansion a fluid flow field in cylindrical coordinates with axial symmetry, is simulated by a network of electrical resistors. A series of DC analog computing units, connected to the network bounrlary corresponding to the free surface effectively adjust the network parameterr to satisfy simultaneously Laplace's equation and the borrndary conditions. The system automatica1ly "re1axes" to the correct boundary shape in a fraction of a second. A detailed application of the method to the water coning problem in oil wells is presented. INTRODUCTION The water coning problem in petroleum production is a prime example of a class of problems known as free surface problems. A free surface arises in fluid flow regions when the shape of the boundary of a single phase flow region is affected in some manner by the pressure or potential gradients within the region. When there exists an interface of two fluids of different densities, the shape of this interface will be determined by the relative velocities of the two fluids and will therefore comprise a free surface. Other free surface problems of interest to petroleum engineers include the gas coning, water injection, and gravity drainage probIcms. In each case it is desired to predict the shape of the boundary of the oil zone as a function of the flow rate, the well penetration and the physical parameters and dimensions of the system. Such problems do not lend themselves to the classical analytical treatments of boundary value problems because in this case the boundary of the potential field and the potential distribution within the field are interdependent and must be calculated simultaneously. A further difficulty arises from geometric considerations. Since the fluid flow is of the radial type in most cases, such effective methods as conformal transformation and the hodograph are not applicable. It is the purpose of this paper to present a method whereby free surface problems of this type may be solved rapidly to the desired order of accuracy by means of a combination of a network of electrical resistors and conventional analog computer units. The water coning problem is treated in some detail. Then the procedure for extending the technique to other free surface problems is indicated. FORMULATION Most commercial oil reservoirs consist of an oil-saturated sand, bounded above by an impermeable strata and below by a water-saturated sand. Gravimetric separation results in a horizontal oil-water interface. When an oil well is drilled so that it partially penetrates the oil zone, and production is initiated at a constant rate, the oil-water interface will assume a new shape as a result of the pressure gradients in the oil zone. It should be emphasized that this is a steady phenomenon. After an initial transient period the water phase will be completely static and only the oil will be in motion. The new steady-state shape of the interface, as shown in Fig. 1, depends upon the depth of penetration, d, the thickness of the oil zone, I, the production rate, q, the hydraulic permeability zone of the sand, k, the viscosity of the oil, µ, and the densities of the oil and water, p.,. and pw.. The problem is to determine this relationship. Darcy's law + = - (P f g p z).....(1) it.

Jan 1, 1957

By E. Tulcanaza

The practical significance of the in situ grade variability is usually neglected. Although recognized, often times it is either ignored or just considered as a vague guideline in many of the decisions dealing with exploration, reserve estimation, and mine planning. This paper stresses the significance of grade variability for exploration and mining, and illustrates its liaison to the structural features of the ore deposits, as well as to the mining parameters used for mine extraction. Some geostatistical results obtained from a silver mine, tungsten mine, and copper mine in South America are discussed.

Jan 1, 1985

By D. V. Carter, Dan C. Williams, John R. Coombs

Exploration was active in East and East Central Texas during 1944. Ten oil fields were discovered during the year, of which four show promise of development. The discovery wells of the Sand Flat and Tyler, South fields were drilled to a depth greater than 10,000 ft., and the latter field now produces from the Pettit at a depth of 9890 ft. The Sand Flat well was plugged back to the Paluxy. The other two fields are Glen Rose producers near 8000 ft. The Pickton field produces from the Bacon Lime and Winnsboro from the Rodessa section. The Eylau field, Bowie County, was significant as the first Smackover production in Texas. Magnolia drilled a test in the Concord field, which topped salt. The most extensive and significant development in the district was the Carthage gas-condensate field. It expanded from the 8000 acres of last year to an estimated 190,000 acres, or about 300 sq. miles, and is not defined as yet. The first oil production in the Carthage area was made from the Travis Peak in 1944 in the Rogers Lacy's Cameron Lumber Company well No. I, on the northwestern side of the field. The New Hope field, Franklin County, scored the largest number of completions during 1944 with 24, bringing its total number of wells to 27. Two more pays were opened and produced as dual completions with the older horizons. The Manziel field, Wood County, had 19 new wells added during the year, for a total of 29, while the Pittsburgh field, Camp County, reached a total of 23 wells by completing 14 new ones. Material shortages and drilling restrictions dropped the total number of producing wells completed in the district from 171 during 1943 to 141 for 1944. Abandonments increased from 531 during 1943 to 609 for 1944. Of this number, 479 were in the East Texas field. Subsidy payments had very little effect in the district and it was mostly a few of the old fault-line fields that had any wells to fall within the requirements for subsidy payments. The prices of crude oil remained constant in the district except for increases as a result of subsidy payments. Production and Probation Wartime demands called for increased allowables for many fields, consequently the condensate and oil production for 1944 increased to 190,016,180, which is up 6.9 per cent over 1943. The East Texas field, of course, remained the principal producer of the district, accounting for 134,768'499 bbl. during the year, or 71 per cent of the district total production of condensate and oil. The field topped its own 1943 production by 4.8 per cent and became the first field in the world to produce 2 billion barrels of oil. The Hawkins field remained the second largest oil producer in the district, with 13,317,088 bbl. for the year, a drop of 6.8 per cent from 1943, while Van field was third with 11,635,708 bbl. The

Jan 1, 1945

By Arthur F. Colombo

The selective - deslime - flotation process developed by the Federal Bureau of Mines as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The operating parameters for the selective flocculation - cationic flotation of oxidized taconites from the western Mesabi range in Minnesota are discussed. Data from the operation of a 410 kg/hr (900 lb/hr) pilot plant employing reclaimed water are summarized for 2 types of oxidized taconites.

Jan 1, 1979

By F. H. Daniels

IN this, paper it is my intention to, call your attention to* a few of the many producers using blast, now, in common use in Sweden, and also those constructed by the Washburn & Moen Manufacturing Company at their Quinsigamond Works. During a prolonged stay in Sweden the writer had an opportunity

Jan 1, 1881

By Chas. Y. Clayton, Francis B. Foley, W. E. Remmers

DuRing the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr. Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.' Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 1, 1926

By H. E. Rorschach

Activity in Oklahoma fields declined in 1938 from the banner year of 1937. During the year, 1768 wells were completed as compared to 2632 completed during the year 1937. The following tabulation sets out details regarding the wells completed during the year: These computations do not take into account the wells drilled for repres-sure and salt-water disposal, and other nonexploratory wells. Purchasers' reports filed with the Corporation Commission of the State of Oklahoma show a total of 168,789,229 bbl. of oil purchased from Oklahoma leases in 1938, or a daily average of 462,436, a decrease of about 25 per cent from the year 1937. The outstanding operation of the year was the further development of the Ramsey pool, in western Payne County, the producing horizon being classified as the Wilcox. This pool was discovered on the last day in the year 1937, by the Mid-Continent Petroleum Corporation drilling on a unitized block in see. 18, T. 18 N., R. 2 E. The map in Fig. 1 shows the development at the end of the year 1938. An important discovery of the year was the Champlin Refining Company's No. 1 Boehm, in Garfield County, sec. 4-24N-8W., the producing horizon being the second Wilcox found at a depth of approximately 6700 ft. This pool was assigned the name of Hillsdale. Some of the offsets to this discovery well had not come up to expectations at the end of the year, but the discovery seems to be important as indicating that the Wilcox sand is productive in the Anadarko Basin area, providing that the right structural conditions are present.

Jan 1, 1939

By H. E. Rorschach

Activity in Oklahoma fields declined in 1938 from the banner year of 1937. During the year, 1768 wells were completed as compared to 2632 completed during the year 1937. The following tabulation sets out details regarding the wells completed during the year: These computations do not take into account the wells drilled for repres-sure and salt-water disposal, and other nonexploratory wells. Purchasers' reports filed with the Corporation Commission of the State of Oklahoma show a total of 168,789,229 bbl. of oil purchased from Oklahoma leases in 1938, or a daily average of 462,436, a decrease of about 25 per cent from the year 1937. The outstanding operation of the year was the further development of the Ramsey pool, in western Payne County, the producing horizon being classified as the Wilcox. This pool was discovered on the last day in the year 1937, by the Mid-Continent Petroleum Corporation drilling on a unitized block in see. 18, T. 18 N., R. 2 E. The map in Fig. 1 shows the development at the end of the year 1938. An important discovery of the year was the Champlin Refining Company's No. 1 Boehm, in Garfield County, sec. 4-24N-8W., the producing horizon being the second Wilcox found at a depth of approximately 6700 ft. This pool was assigned the name of Hillsdale. Some of the offsets to this discovery well had not come up to expectations at the end of the year, but the discovery seems to be important as indicating that the Wilcox sand is productive in the Anadarko Basin area, providing that the right structural conditions are present.

Jan 1, 1939