Search Documents

By J. E. Johnson

The general construction of blast-furnaces has undergone no radical change in more than a generation. When the old style of masonry construction was replaced by the steel shell, the masonry piers were simultaneously replaced by columns, never lese than 6 and frequently 12 or 16 in number, set under the mantle-ring. These columns were at first unvaryingly made of cast-iron, but in more recent years have frequently been made of structural steel. The furnace itself has recently been the subject of radical changes; in some cases the thin-lined construction has been adopted for the whole furnace, and in other cases it has been adopted for a zone immediately above the bosh, raising the mantle several feet to make this possible, but still the style of construction with columns set immediately under the mantle has been universally followed. In spite of the apparent fixity of this type of construction it is open to grave disadvantages from the operating point of view, which may be briefly outlined as follows: The slope of the bosh and size of the crucible are such as to leave scant room inside the columns for the necessary water-piping, etc. The bustle-pipe must necessarily be outside the columns and the penstocks have to pass between them, with the result that the columns are frequently much in the way when changing the tuyeres or otherwise handling the penstocks. Moreover, the hearth-jacket requires a diameter but little smaller than the circle of the inside of the columns, and as a result the cooling-water ditch for protection against breakouts is exceedingly limited in width. As a consequence of these conditions, when any work requires to be done around the furnace, such as changing a tuyere or working on the cooling-water pipes, the amount of room left between the columns, pen-

Jan 1, 1913

By Robert L. Marovelli

A recent reorganization placed the health and safety research activities of the Bureau of Mines under a director, Division of Minerals Health and Safety Technology. The new health and safety research organization and its position in the Bureau hierarchy is shown in Table 1.

Jan 11, 1979

By I. N. Zavarine

AUSTENITE is often defined as a solid solution of carbon or carbide in a nonmagnetic form of iron. Conversely, magnetic measurements are often used by investigators for the purpose of detecting the degree of austenite decomposition after an iron alloy has been subjected to certain thermal or mechanical treatments. Association of the magnetic state with the gamma-phase decomposition is often extended to the alloys of iron with elements other than carbon. Definition of austenite as a nonmagnetic solid solution cannot be accepted in the light of available information without certain reservations. The relation of magnetic transformations with the gamma-phase decomposition in the complex alloys of iron has never been rigorously proved. The present investigation deals primarily with the magnetic trans-formation that occurs in carbon steels during the quenching process. The work was further limited to a study of magnetic transformation in carbon steels quenched at such rates as are necessary to retain the product of austenite decomposition in a martensitic state.

Jan 1, 1934

By Warren Howes, C. O. Anderson, Robert E. Illidge, M. D. Harbaugh, S. J. Burris

The Tri-State zinc-lead mining district embraces an extensive area, including the northeastern part of Ottawa County, Oklahoma, the southeastern part of Cherokee County, Kansas, and adjacent portions of Missouri, mainly in Jasper County. The Oklahoma-Kansas portion of the district, in the vicinity of Picher, Okla., has been the principal producing area since 1917, and the present milling practice in that section is the subject of this paper. This district is the largest zinc-producing field in the United States. In 1926 it produced 55 per cent of the nation's zinc and 15 per cent of its lead, and in 1933 it produced 35 per cent of the zinc and 10 per cent of the lead. From 1842 to 1933, inclusive, the total output of the district was 18 1/2 million tons of zinc and lead concentrates valued at 818 million dollars. Of this production, the Oklahoma-Kansas, or Picher, field yielded over 9 million tons valued at over 400 million dollars. Mining operations in the Oklahoma-Kansas field near Picher and Baxter Springs began in 1915. The mills built it that time consisted merely of gravity concentration plants employing jigs and tables and the same flow sheets as had proved satisfactory with the free-milling ores such as were mined in the Joplin-Webb City fields in Missouri. The Kansas-Oklahoma ores proved to be much richer but also more refractory to treatment than those in the Joplin area, and contained a considerable percentage of zinc mineral not freed by the amount of crushing usually practiced in preparing the ores for jigging. Thus the old Joplin type of mill, with its usual two or four jigs and a few tables, proved inadequate and resulted in excessive tailings losses sometimes as high as 50 per cent

Jan 1, 1935

By P. Barnes

(Read at the Wilkes-Barre Meeting, May, 1877.) THE tabular statement accompanying this note shows the money cost in each of the three departments of manufacture, of 17 leading items, and also the proportion (expressed in a decimal fraction) which each of these items bears to the total cost. The statement can hardly be taken for more than an average illustration of the clear showing of ratios and of results which may be made by such an arrangement, for not only will these items vary from month to month in any given works, but the methods themselves of manufacture differ widely in different works. It is obvious that such a statement, however useful it may be, must be submitted with but exceedingly little explanation or discussion, or with none at all, for the reason that to enter at any satisfac-

Jan 1, 1878

By Allen D. Garrison

THE chemistry of clays and shales has been assuming increasing importance in the petroleum industry, and two factors have greatly influenced this trend. The first has been the growing evidence that the marine shales are source beds, and that the petroleum compounds have migrated to the sand reservoirs overlying or underlying these shales: the second has been the demand for drilling fluids better adapted to penetrate these marine shales without difficulty and expense. ORIGIN AND GENERAL COMPOSITON OF CLAYS AND SHALES Clays, shales and surface soils are all closely related materials. They are mixtures of finely divided compounds formed during the weathering of the solid crust of the earth. Their nature is essentially colloidal; that is, their behavior is determined by the state of division of the materials and the surface reactions of the smallest grains. Many of their chemical changes affect only the exposed areas and do not involve the interior of the grains of matter. The extent of these reactions is more nearly proportional to the area of the substances than to their mass, therefore it is possible for a small amount of a material in an extremely fine state of division to completely dominate the character of the mixture. More than 83 per cent of the crust of the earth is composed of three elements-oxygen, silicon and aluminum. Consequently, the corrosion products of the crust are predominantly aluminosilicates, or compounds of aluminum, silicon and oxygen. If we add the compounds of six elements-iron, calcium, sodium, potassium, magnesium and hydrogen-more than 98 per cent of the crust has been accounted for. These six elements, together with the first three, also appear in soils, clays and shales. But direct chemical analysis is of little value in describing the nature of such materials. Many chemical individuals may be present in variable amounts, and the extreme subdivision of any one of the individuals may contribute qualities that dominate the mixture.

Jan 1, 1939

By Waldemar Lindgren

No one would maintain that all ore deposits or all deposits of useful minerals have been formed by the same processes. Generally they have originated by special processes of concentration but these may be of many different kinds. Some deposits have their origin in chemical or biochemical processes of concentration in rivers, lakes or seas, others developed on land by means of chemical reactions of surface waters on various forms of rocks. Certain insoluble substances remained behind; others were dissolved and precipitated in favorable places. This action proceeded in the realm of the oxidizing surface waters or in the deeper zones to which the waters from the surface could find their way. Examples of the latter kind may be found in the extensive copper and vanadium deposits of some sedimentary beds or in the lead and zinc deposits of certain broad limestone strata. In these instances the evidence for any other mode of origin would seem to be very weak indeed.' Nor does it seem possible to deny that circulating waters may form deposits of the more common metals along fissures after having dissolved many constituents from paths traversed. Another very large class has been formed by magnetic processes of concentration. The last 40 years have been a period of intense activity in the investigation and description of a vast number of deposits; all modern methods have been employed and the result is an accumulation of data, difficult or impossible to master. It has been a period similar to that in petrography. The generalizations, the able deductions, have lagged behind. Evidently several geologists have become weary of this "infinite detail" and a mistrust of the microscope seems to have arisen. Although this feeling of being swamped in microscopic detail is a painful experience, nevertheless only through the detail in combination with the large features, and only by utilizing all the related sciences shall we

Jan 1, 1927

By R. M. Larsen

The Rocky Mountain region is defined with some variations for different purposes or by different organizations. For oil and gas development, Wyoming, Montana, Colorado, northwestern New Mexico, and Utah are included in the order of their apparent importance. Portions of adjoining states, such as North and South Dakota, Nebraska, Arizona, Nevada, and Idaho, arc attributary to this region, but have little or no oil or gas production. Nebraska and New Mexico are considered separately (see pp. 412 and 415), and most of the discussion in this report will be confined to Colorado, Montana, and Wyoming. Utah has produced about 200,000 bbl. of oil from the San Juan and Virgin fields, which are isolated and shut in at present. The Clay Basin field in northeastern Utah produces natural gas and distillate, and the Farnham field in central Utah produces carbon dioxide gas. Other Utah areas of some interest are listed in Table I. The Cedar Creek (Baker-Glendive) field in southeastern Montana extends into North Dakota, but is listed under Montana. The other states are in the main wildcat areas, and exploration in 1944 was at a minimum. However, geological and geophysical parties are reviewing them for further testing. Oil production in Colorado, Montana and Wyoming was 459,000 bbl. more than in 1943. Increases of 713,000 bbl. in Colarado and 731,000 bbl. in Montana offset a loss of 985,000 bbl. in Wyoming. This was the first decline in Wyoming since 1938. Field production figures and state totals are given in Table I. Total drilling activities in these three states and Utah increased from 687 wells making 1,442,511 ft. of hole in 1943 to 916 wells making 2,245,803 it. in 1944. Wildcat drilling increased from 163 wells making 331,193 ft. of hole in 1943 to 171 wells making 389,144 it. in 1944. These figures include all drilling wells making footage, not starts or completions, and represent an all-time high in drilling. The year 1944 witnessed the greatest concentration of seismograph activity that the region has had. The Rocky Mountain Oil Scouts Association reported that in 1943, the previous peak year, 91 crew months of work were performed; in 1944, the time was 254 crew months. About 67 per cent of the work was in Wyoming, 18 per cent in Montana, and 12 per cent in Colorado. Twenty-three blocks totaling 400,000 acres were reported assembled in Colorado, and 161 blocks totaling 4,000,000 acres in Wyoming. Information about other states was not given. Fourteen unit agreements were approved by the Department of the Interior, as compared with 13 in 1943. The 1944 agreements were all in Wyoming. In five of the unit areas, oil or gas discoveries were made, four were dry, and five were drilling Or pending' Oil companies find it advantageous to unitize blocks containing any proportion of public domain. Units for

Jan 1, 1945

By J. W. Furness

Before attempting any discussion of the importance of tariff enactments as applied to exhaustible resources, certain basic factors should be emphasized. First, it must be remembered that minerals differ from organic substances in that they are irreplaceable, and when once taken from the earth's crust enter into uses which ultimately dissipate them, so . that they cannot be recovered for future use. A second factor entering into the problem is the unequal distribution of the mineral deposits of the world. No industrial nation has within its political confines a sufficient quantity of all the minerals necessary for the maintenance and advancement of present civilization; hence international exchange of these commodities is inevitable. As minerals are essential to modern industry, the supply available to any given nation constitutes a factor which limits its ambition to advance industrially. A nation which has this ambition endeavors to secure not only a supply of minerals sufficient for its current needs, but also sources which will assure it expansion. Should mineral raw materials be withheld from such a nation by enactment, it seems inevitable that every effort will be made to obtain them, and that, should the nation deem itself sufficiently powerful, its ultimate recourse will be force. Thus the importance of tariff enactments, not only from the standpoint of industrial prosperity but from the standpoint of international peace, can be appreciated.

Jan 1, 1932

By R. B. Schluter, M. M. Fine

A process for winning copper from pelletized chalcocite concentrate without matte smelting and converting is under development at the Twin Cities Metallurgy Research Center of the U.S. Bureau of Mines. The new procedure includes a two-stage fluid-bed treatment in which the pelletized concentrate with 33% Cu and 7% S is first desulfurized to about 0.5% S in an oxidizing atmosphere, and then metallized by reduction with hydrogen. The reduced product is melted with flux to separate metallic copper from the gangue. The metal must be refined to remove residual sulfur and iron. The pelletizing of the fine concentrate into mini-pellets prior to fluid-bed treatment is an important feature of the process, because it permits shorter reaction time, decreases dusting, and facilitates subsequent processing.

Jan 1, 1972

By F. M. Lewis, J. F. Myers

The selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore—in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearse deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table I shows a typical analysis of the two ores as well as of the mineral content.

Jan 1, 1947

By J. F. Myers, F. M. Lewis

The selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore—in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearse deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table I shows a typical analysis of the two ores as well as of the mineral content.

Jan 1, 1947

By Alfred Weiss

Daniel C. Jackling's innovative concept for handling low grade ores ushered in a new philosophy of open pit mining. As one of the greatest minemakers of all times he revolutionized major segments of the industry and helped strengthen US defense efforts during World Wars I and II by making possible the tremendous copper supplies from US mines. Many great mining men have since followed in his footsteps with their discoveries of new orebodies or development of new mines. Their brilliance in leadership can also be traced to the coupling of a new idea to the physical nature of the materials in the earth's crust or to the extractive stages of minerals recovery. The minerals industry is now in another era of change and must again devise techniques to meet the challenge. The task is not only to create new exploration techniques and develop new mining methods, but, I believe, to optimally apply new concepts and tools in daily decision-making.

Jan 11, 1978

By F. R. Brotzen, L. D. Whitmire

Single crystals of high-purity molybdenum were de-formed at temperatures from 195°to 473°K, and the effect of deformation on the electrical resistivily was deler-mined. To separale the resislivity components of point and line defecls some cryslals were annealed at 473°K. The vale of resislivily increase wilh strain was nearly linear and was strongly dependent upon the deformation temperature. Point dejects are annealed out without any effect on the flow stress. At low temperatures the flow stress is a linear function of the square root of the resistivity increase attributable to dislocations. ELECTRICAL-resistivity measurements have been used successfully to gain information on structural changes in metallic materials. During plastic deformation the electrical resistivity rises because of electron scattering from newly created lattice defects. Such measurements lend themselves, therefore, to corroborating results from direct observation of lattice defects and, to a certain extent, to correlating defect densities and distribution with mechanical properties. Published information on research with single crystals of the bcc metals of Group VI, particularly molybdenum, is still limited. Yet, molybdenum single crystals of relatively high purity can be readily prepared by electron-beam-melting techniques. Furthermore, some valuable information on the defect structure of deformed crystals by direct observation is available. Lawley and Gaigher,1 for example, have examined dislocation configurations in deformed molybdenum crystals by means of transmission electron microscopy. Their results revealed that the dislocation density and distribution were strongly dependent upon the deformation temperature. These findings differed from those by Keh and weissmann,2 who found that the average dislocation density in polycrystalline iron deformed between 138° and 298°K depended only on the degree of strain and not on the deformation temperature. Martin3 and peiffer4 showed that point defects introduced in polycrystalline molybdenum by cold work can be eliminated by annealing at a relatively low tempera-ture. In view of their work it became apparent that resistivity measurements of suitably annealed crystals could disclose changes in their dislocation structure and contribute to the understanding of the work hardening of molybdenum crystals. EXPERIMENTAL PROCEDURE Crystals were grown by electron-beam zone melting5,6 of 0.062-in.-diam molybdenum rods (99.99 pct) supplied by General Electric Lamp and Wire Division, Dover, Ohio. The crystals, about 4 in. long, were prepared by using five zone-refining passes at a speed of about 6 mm per min in a vacuum of about 5 X l0-6 Torr. The resistivity ratio of the crystal, p(4.Z°K)/p(273°K), was generally near 10-3. These crystals were used as tensile specimens of uniform diameter in the "as-grown" condition. They were oriented for maximum shear on the (011)[111] slip system (Schmid factor >0.49). The specimens were held in spherically seated Templin-type grips so as to minimize bending. Samples were deformed on an Instron machine at a strain rate of about 5 X 10-5 sec-1 in an isopentane bath with dry ice at 195°K, in ice water at 273°K, and in a vegetable-oil thermostat at 373° and 473°K. The temperature in the latter was maintained constant within +2°K. Resistance measurements were carried out with a Kelvin double bridge. The resistance of the potential leads was kept low by using large-diameter wires outside the low-temperature bath. Many of the resistance data were checked by measurements made with an ac bridge. Current and potential leads were spot-welded to the specimens. The distance between the potential leads, about 3 in., was also considered to be the gage length for the strain measurements. Diameter and gage length of the samples were measured optically with an error of less than 2 pct. These measurements were used also to insure that the deformation had been uniform over the gage length of the specimen. Resistivity changes were then determined from the resistance measurements at 4.2°K assuming constancy of volume. In the course of a test, the crystal diameter, gage length, and resistance at 4.2°K were determined first in the initial state and subsequently for various amounts of elongation.

Jan 1, 1968

By Charles E. Glass

A steadily growing body of evidence indicates that earthquake ground motions can cause failure of rock slopes that are otherwise stable under static loading conditions. As a result, the economic optimum working slope angle is reduced when earthquake shaking is considered in surface mine design, especially in regions of high seismicity. When designing surface mine slopes to withstand seismic motion it is as important to consider the probability of experiencing various levels of ground shaking as it is to consider the characteristics of the ground motion. For most slope designs, simple probabilistic techniques such as extreme value or maximum likelihood techniques are appropriate. These techniques, however, should be applied in such a way that a probability value is assigned to characteristic ground motion parameters at the mine rather than to nearby earthquake magnitudes. Several techniques have been developed to analyze rock slopes subjected to dynamic loads. Most of these techniques do not adequately account for the ground motion parameters of concern. The best technique appears to be one that utilizes actual earthquake time histories. A simple technique that calculates block displacement for any input accelerogram, using a linear acceleration approximation between time steps, has been developed that accurately accounts for rock block response. Results using this technique indicate that the following factors are important for assessing rock slope stability in earthquake regions:

Jan 1, 1983

By M. Cohen, R. T. Howard

It has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkinl has shown that the compositions of two coexisting phases in a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanaly-sis. Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantita-tive way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of this research could not be treated satisfactorily by other quantitative tools, such as specific volume,' magnetic,6 dila-tometric, electrical resistance7 or x-ray measurements.a It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. Literature Survey Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1948

By M. Cohen, R. T. Howard

It has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkinl has shown that the compositions of two coexisting phases in a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanaly-sis. Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantita-tive way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of this research could not be treated satisfactorily by other quantitative tools, such as specific volume,' magnetic,6 dila-tometric, electrical resistance7 or x-ray measurements.a It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. Literature Survey Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1948

By Kenneth S. Ritchie

The natural emulsion samples used in this study were shipped directly from twelve California oil fields, through the courtesy of the superintendents of the main producing companies in those fields. Representative parts of each sample were chosen for the slides. Preparation of the slides was generally made in less than two minutes, including time of exposure; in a few cases, about five minutes was required. The short time was intended to minirmize the changes in conditions. Whenever comparison was of value, standard conditions were established. Spreading by gravity was adopted instead of smearing. Cover glasses were not allowed to rest on the films. General Characteristics of Emulsions The main purpose of the general views (Figs. 1-16) is to illustrate the general characteristics of the dispersed droplets together with any other constituent or impurity that may be found in each emulsion. The magnification is given so that dimensions could be measured from the plates. The slides used for these views had spherical recesses; they gave the best light. Where crystals were intended to be shown in the picture a filter (green was the best') was usually used. Emulsions that showed a tendency to move by concentrated light were pictured without a condenser.

Jan 1, 1931

By N. A. Ziegler

A CERTAIN amount of interest has been indicated recently in the resistance to oxidation at high temperatures of iron-aluminum alloys (rich in iron). Hautman1 published a paper in which some interesting results are given. According to his paper, only alloys containing at least 8 per cent aluminum indicate a marked improvement in their resistance to oxidation. At about this aluminum content, however, alloys become brittle, which considerably reduces their commercial value. About two years ago the author performed a series of experiments, the results of which are presented here. A series of iron-aluminum-carbon alloys was prepared by melting electrolytic iron, aluminum and high-carbon iron alloy in an induction vacuum furnace.2 The list of these alloys is given in Table 1. Each alloy was forged in the ordinary way to

Jan 1, 1932

By Sandip K. Mitra, John E. Dorn

The Basinki-modified Seeger equation for deformation of metals by means of thermally activated intersection of dislocations was used to ascertain the various factors responsible for the strain hardening of poly crystalline aluminum and a series of a solid solutions of magnesium in aluminum. The analyses were based principally on the rate of change of strain rate with stress and the Cottrell-Stokes ratio. From measurements of these quantities on a series of strain-hardened states, the force displacement diagram for intersection, the density of dislocations in the entanglements, and the contributions of the athermal local stress and long-range stress interactions were deduced. Poly crystalline aluminum was observed to have the same force-displacement diagram for intersection as single aluminum crystals, and the corresponding diagram for the magnesium alloys differed in a manner that suggested that small amounts of magnesium may decrease slightly the stacking fault energy of aluminum. Although poly crystalline aluminum had about the same initial density of dislocations as the single crystals, the density of dislocations increased much more rapidly with strain in the polycrystals. This factor and the higher back stresses generated in the poly crystalline aluminum were the major factors responsible for the higher strength of the poly crystalline aluminum, As the magnesium content of the alloys was increased, the initial density of the dislocations also increased. Most of the alloy strengthening arose from this factor; alloying effects due to short-range order strengthening, Suzuki locking, Cottrell pinning, and so forth, were estimated to be quite small. The gveater rate of strain hardening in the alloys was deduced to be due primarily to the greater increase in the density of the dislocations with strain as the magnesium content was increased. It is the purpose of the present investigation to shed additional light on the average plastic behavior of a grain in a polycrystalline aggregate, by analyses, based on dislocation theory, of appropriate experimental test results. These deductions when compared with those from single-crystal data will then serve to illustrate the major items of difference between the plastic behavior of single crystals and the average behavior of a grain in a

Jan 1, 1963