Search Documents

By P. K. Chatterjee

The overall success of many strip coal mining operations depends primarily upon the efficient use of draglines to remove overburden. These machines require enormous capital investment and unless used efficiently the profitability of a venture is adversely affected. It is important that the dragline works continuously and it is imperative that the walking path and other facets of its operation be predetermined exactly so that the desired production rate is achieved with a minimum of non-productive time. Details of dragline operations which are of particular interest are walking path, prediction of best cut and positioning to maximize production, the angle of swing which produces the swiftest operation, optimum fill factor allowable for the type of material and conditions of ground, the maximum depth from which it can excavate and operating level with respect to the elevation of the high wall. The aims of the present paper are: 1. To establish a cut-off point in the cost-depth ratio. 2. Predict the most economic method of stripping in a given area using graphical plots of walking path implemented with information necessary to ensure optimum production. The optimum operating efficiency of the dragline in relation to the terrain and other conditions imposed on its operation will be evaluated. The model is based upon operating data which has been collected from site observations of a large strip coal mining operation in Central Queensland, Australia.

Jan 1, 1977

By Jack Parker

The White Pine mine site lies five miles south of Lake Superior in Ontonagon County, Mich. Copper sulfide, mixed with some native copper, is mined by a room-and-pillar system from gently dipping Upper Kewee-nawan sediments. Depth of mining now varies from 700 to 1800 ft and the ore body continues to a depth of at least 3400 ft. An area roughly 21/2 miles square has already been mined. Mining height has varied from 61/2 to 22 ft. A rock mechanics program was set up in late 1963 to promote safety and mining efficiency. This note reports some of the findings. Rock Strength Compressive strength of small, dry specimens of sandstones, siltstones, and shales from the ore zone varies from 20,000 to 30,000 psi. This is intermediate between the softer coal mine sediments and the meta-morphic and igneous rocks of hard rock mines. Annual Cycle of Rock Failure Since 1963, every roof and pillar failure involving more than a few tons of rock has been examined and documented. Some 1500 stations have been installed for measuring convergence, -c1/1000 in., with Invar extensometers. At first it was thought that there was some kind of a cycle of roof failures; perhaps annual, perhaps even elated to the moon or to earth tides, but records (see

Jan 1, 1971

By T. R. A. Gokcen

THE possibilities of separating and purifying metals by high vacuum distillation were examined by Kroll.1 He suggested vacuum treatment for the removal of zinc from the lead produced after Parkes desilverizing. The St. Joseph Lead Co. developed the first commercial vacuum dezincing process at their Herculaneum refinery, as described by Isbell.² The Broken Hill Associated Smelters at Port Pirie, Australia, has, after several years of pilot plant operations and fundamental investigations, developed a continuous process, which will be described briefly in a forthcoming publication." As the full-scale continuous vacuum dezincing plant at Port Pirie is still experimental, publication of full practical details of the plant will be deferred until the unit is operating as a normal part of the continuous refinery. This paper deals only with theoretical aspects of vacuum distillation processes, with particular reference to vacuum dezincing. The method of mathematical analysis is of general interest as it may be applicable to other metallurgical separations which have been investigated recently.4-6 Evaporation Processes At about atmospheric pressure, or higher, most liquids possess a boiling point—a temperature at which any heat put into the liquid is absorbed only as latent heat, not as specific heat. If a steady heat input is supplied, the liquid's temperature rises to this value, then remains constant while bubbles of vapor form beneath the surface. The rate of evaporation is determined solely by the rate of heat transfer to the liquid; the temperature of boiling is determined by the partial pressures of the volatile constituents in the liquid, and the total pressure above the surface. If the rate of heat transfer to the liquid is increased, the temperature remains constant, and the rate of boiling increases. When evaporating metals under vacuum, however, the partial pressures concerned are generally so small that boiling does not occur, because at even a fraction of a millimeter below the surface the hydrostatic pressure is usually too great to permit the formation of a pocket of vapor. In addition, the high thermal conductivity of metals tends to prevent the local superheating which is necessary for bubble formation.' Although this effect is doubtless also exerted when boiling metals at higher pressures, the magnitude will be less because the degree of superheat required to form bubbles is very much less at the higher temperatures involved. Under vacuum, therefore, evaporation of volatile constituents takes place only from the exposed surface, and the rate of evaporation depends upon the surface area, the surface concentration of volatile constituents, the surface temperature, and the partial pressures of volatile constituents immediately above the surface. If the heat input is raised above a certain level, the effect is not to increase the evaporation rate at constant temperature, but to raise the temperature of the liquid until at some higher level an increased rate of evaporation (and thus of latent heat absorption) again balances the heat input rate.? Many substances (including metals) have a very large intrinsic evaporation rate at quite low temperatures—far below their normal boiling points. However, at atmospheric pressure, the large numbers of atoms evaporated are almost completely deflected back into the liquid (or solid) surface by air molecules. Thus the back condensation rate is practically equal to the gross evaporation rate, and the net evaporation rate is practically zero. It can therefore be seen that an overall distillation rate depends not only upon the intrinsic evaporation rate, but also upon the ability of the volatile atoms to move away from the evaporating surface. This movement is facilitated by the provision of a condensing surface close by. Vacuum Distillation: The function of the vacuum above the evaporating surface is to remove foreign molecules, so that the chances of deflection of an evaporated atom back into its source are reduced. When the residual gas pressure is reduced so far that the evaporated atoms have a high probability of reaching a nearby condensing surface without suffering collision with a foreign molecule, the state of affairs is termed "molecular distillation." This process is practiced commercially today for the purification of numerous organic chemical products of high unit value, but not, to the writer's knowledge, for any metallurgical separation. When the degree of vacuum produced in a still is not sufficient to promote molecular distillation, then the evaporated molecules must diffuse through the

Jan 1, 1954

By Franklin J. Kay

Introduction The methods used in surface, mining vary throughout the world, depending on many variables such as: the types of over- burden materials, the depth of the overburden, the thickness of the seam, and other operational choices, both financial and functional. However, the stripping machines are typically draglines, stripping shovels, excavators, scrapers, loaders, and bulldozers. In all cases the economic feasibility of mining thin seams depends on the market needs, the market location, the equipment used, the mine management, the quality of the coal, and the labor market. Slight negative combinations of these parameters have closed many mines while positive combinations allow others to exist. The limited mobility or slow movement of large stripping shovels, draglines, and bucket wheel excavators make them more economically fitted to areas where large quantities of overburden are to be moved. This is necessary to keep the transfer and setup time between pits a negligibly small percent of the total operational time. Equipment such as the scrapers, loaders, backhoes, trucks, and bulldozers that are either very mobile or can be trailered is more versatile and can be used in the smaller area mines.* Mobile equipment is also more practical in areas with shallow overburden because of the constant movement required while removing overburden. In thin coal seams the equipment is usually paired such that the operational equipment can be listed as: (1) dragline-loader, (2) shovel-truck- loader, (3) scraper-loader. (4) loader-truck-loader, or (5) loader-loader. In these operations the overburden is removed with the first machine(s) of the pairing and the loader or loaders are used for coal production. Recent articles in Coal Age (Chironis, 1978) and Mining Engineering (Wiebmer, 1978) have discussed varying philosophies in mining similar seams of coal. One operator uses draglines for competitive mining while the other uses scrapers for the same purpose. Both cite strong cases sup- porting their choice of equipment as good sound economic decisions and their success supports their choices. The drag-line operation is adding new larger draglines to decrease the cost of mining, rather than to increase coal production. The scraper operation has also gone to more and larger scrapers for basically the same reasons. These operations and all

Jan 1, 1981

By Herbert J. French

Herbert 1. French (Member 1934), vice president of the International Nickel Co. Inc., assistant vice president of the International Nickel Co. of Canada Ltd., and AIME Howe Memorial Lecturer for 1956, died in Rochester, Minn. on Aug. 17, 1955, after a long illness. Before his death, Mr. French had laid the foundation of research on which the Howe Memorial Lecture (p. 770) was based. His associates at Inco, 0. 0. Miller and J. W. Sands, were able to complete the project, present the lecture, and prepare it for publication, following Mr. French's general outline. Born in New York on May 27, 1893, he graduated from the School of Mines, Columbia University, with a degree in metallurgical engineering in 1915. Mr. French gained his early engineering experience with the American Smelting and Refining Co., serving as a chemist and as-sayer at the company's Murray, Utah, installations. He later returned east and became a metallurgical engineer for the General Vehicle Co., Long Island City, IT. Y., a subsidiary of the General Electric Co. In 1917 Mr. French was appointed civilian inspector of materials for the U.S. Army Signal Corps, and continued this work when it was later absorbed into the Bureau of Aircraft Production. Subsequently he was appointed district inspector in Philadelphia for the Pittsburgh (Ordnance Metallurgical) office, later transferring to Pittsburgh. After World War I Mr. French became an assistant physicist on the metallurgical staff, U. S. Bureau of Standards, Washington, D. C. During his years with the Bureau, he was successively associate physicist, metallurgist, senior metallurgist, and assistant chief, division of metallurgy. In 1929 Mr. French joined International Nickel as a metallurgist at the company's Bay-onne, N. J., research laboratory. Transferring to the development and research division, New York, in 1931, he took charge of alloy steel and iron development, becoming assistant manager of this division in 1943. Mr. French's appointment as an Inco vice president came in March 1947. Previously, he was appointed assistant vice president of the International Nickel Co. of Canada Ltd. in January 1947. Mr. French served the War Production Board during World War II as senior technical consultant in charge of the metallurgical and specifications section of the iron and steel branch. When this section of the WPB was organized into the steel division, he was appointed chief of the metallurgical branch. From March 1944 to September 1945 Mr. French served as assistant director. Herbert French was well known not only for his prolific contribution to the metallurgical literature, for which he received numerous awards, but also for his prolonged service to the profession through its technical societies. He was a past president of ASM, and was the Campbell Memorial Lecturer for that group in 1933. Mr. French was honored by the American Society for Steel Treating in 1931 when he was awarded the Henry Marion Howe Medal. A series of lectures he gave in 1941 before the Fourth Western Metal Congress in Los Angeles was later published in book form under the title Alloy Constructional Steels.

Jan 1, 1957

By Pol Duwez, H. E. Martens

The high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to bc cooled of a porous material', so that the cooling fluid can be forced through the pores, In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat, This method, referred to as ((sweat cooling," was pro- posed at the Jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very close control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of Pressure drop. Generally, the Proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequelltl~ the Permeability of the Porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1949

By Pol Duwez, Howard E. Martens

INTRODUCTION THE high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method .of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to be cooled of a porous material, so that the cooling fluid can be forced through the pores. In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat. This method, referred to as "sweat cooling," was proposed at the jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very dose control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of pressure drop. Generally, the proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequently the permeability of the porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1948

By C. E. Westley, R. R. Beebe

Recent works by Plaksh et al.,1,2 Glembotsky,3 and others have renewed interest in the effects of oxidation on the surface activity of the sulfides. Since considerable supporting data are available on galena-potassium ethyl xanthate, this system is being studied at South Dakota School of Mines and Technology by contact angle measurement, using the technique of McGlashan and McLeod.4 The contact-angle method is well adapted to investigation of the influence of small amounts of oxygen on the establishment of a stable contact angle on galena in potassium ethyl xanthate solution. Samples of massive galena containing less than 0.001 pct Cu, 0.001 pct Ag, and 0.01 pct Zn are mounted in castable plastic and ground and polished manually in a glove box containing the desired proportions of oxygen and purified nitrogen. Oxygen and nitrogen contents of the test atmosphere are determined with an Orsatt analyzer. In this way a reproducible surface is created in contact with whatever oxygen concentration is desired. Water and all reagents are prepared and stored in the test atmosphere. An absorbent is used to control carbon dioxide that might be present. Final polishing is done with levigated alumina on a glass plate. The prepared sample is placed in the test solution and transferred to the contact angle apparatus in a sealed box, and the test is conducted while both sample and solution are maintained under a slight positive pressure of the test atmosphere. Table I gives the results of contact angle measurements made at various 02-Nz concentrations.5 Each value of contact angle is the average of at least six individual measurements made with different bubbles at different locations on the sample surface. A period of 20 to 25 min has been found by preliminary tests to be sufficient to permit develop- ment of maximum angle, and all measurements are made after at least this much time has elapsed. Exposure of prepared samples to pure water under the test atmosphere before exposure to the xanthate results in a small but measureable and consistent reduction in contact angle. This is particularly true in the oxygen-deficient atmospheres; for example, at 2.2 pct O2 such water contact reduces the average angle about 8" from that obtained by immediate testing in xanthate. The general trend of increasing contact angle with increasing oxygen concentration corresponds to the results of Plaksin et a12 The absence of diminish-ment of contact angle at very high oxygen concentration has been attributed to the high concentration of xanthate per unit of galena surface: At oxygen concentrations below 1 pct (the limit of accuracy of the Orsatt analyzer), no contact angle is obtained. Furthermore, no contact angle is obtained at any oxygen concentration in the absence of xanthate. This result seems to be in disagreement with those cited by Plaksin.1 Further work on the interaction of galena and potassium ethyl xanthate or a similar collector as influenced by oxygen is contemplated. The true nature of the interrelation is as yet unknown. For example, it is not known whether the governing oxygen reaction is with the mineral, with the reagent, or with both.

Jan 1, 1961

By E. B. Swanson

Crude oil production in Iraq during 1932 was maintained at slightly higher levels than in 1931, but the output continued to be restricted to the requirements of local consumers. The Iraq Petroleum Co., representing British, American and French interests, which has been operating within its concession east of the Tigris River since 1926, began drilling operations on Apr. 5, 1927, and completed its first well at Baba Gurgur on Oct. 14, 1927, to which area the company has since confined its drilling activities. Relatively small quantities of oil have been produced annually, but the products have been utilized in company operations and have not been offered on the Iraq market. The Khanaqin Oil Co., which has its field of operation at Naft Khana in the so-called Transferred Territories, has been supplying the Iraq market with petroleum products from Iraq wells since March 12, 1927. The output of the Khanaqin Oil Co. refinery, at Alwand, during the past three fiscal years ending March 31, has been as follows: (In Barrels of 42 Gallons Each) 1930 1931 11931 Gasoline................................. 102,940 104,571 118,012 Kerosene................................ 104,010 108,112 111,624 Fuel oil...........................1 286,9001 332,142 354,244 503,850 544,825 583,880 The Iraq Petroleum Co. has a small topping plant, with a capacity of about 150 bbl. a day, used in the manufacture of petroleum products for the company's own needs. During the 1932 fiscal year, the production was 3918 bbl. of gasoline and 2235 bbl. of kerosene, as compared with 8157 bbl. of gasoline and 6308 bbl. of kerosene during the preceding fiscal year.

Jan 1, 1933

By R. C. Patterson

IN view of the circumstance that very few important changes have been made within the last 15 or 20 years in the equipment of rod and wire mills, the description of a new process introduced by Grenville Mellen, of Llewellyn Park, N. J., to take the place of the present laborious system of producing rods of lead, zinc, brass, copper, aluminum, etc., may be interesting to members of the Institute. This new process consists in the production of cast rods at one operation in a small continuous casting machine. The hot liquid metal is transferred from the melting crucibles directly into an endless chain of mold blocks in the machine, where solidification takes place, and the rod comes out continuously in a solid form at one end as long as the molten metal is supplied. The operation of these mold blocks so as to produce a solid rod of uniform structure constitutes an important part of Mr. Mellen's invention. The machine (Figs. 1 and 2), 12 ft. in height over all, 2 by 3 ft. in horizontal- cross-sectional area, and 6,000 11). in weight, has a framework of cast iron, holding in position two endless chains of mold blocks, which are made in sections and join in center alignment. The mold orifice is made up of these mold sections, into which the liquid metal flows. The molding chains are composed of steel blocks, grooved on one face to form the molding cavity, and linked together with flexible joints. Each block is carried on four rollers which guide the chain around the end sprockets and carry it in its course through the machine. The accuracy of alignment requisite to the production of a perfect rod in the mold groove formed by these sections is secured by careful machine work, and by building the four ways, down which the alignment takes place, so that two of the sides are fixed permanently, while the opposite sides are held to their position by spring pressure. The guides carrying the molds, while in casting position, are water-cooled square tubes.

Jan 5, 1915

By S. Razi

Injection luminescence of single crystals of rare-earth-activated CdS was investigated. Crystals of CdS:Nd, CdS:Er, and CdS:Yb, grown by the vapor transport technique, were suitably etched and hetero-junctions of Cu2S-CdS were fabricated on one side of the CdS substrate by chemical reaction. The device was then heated to 200°C in an inert atmosphere for 5 min. Static V-I measurements show that at low voltages (V < 1 v) the current is controlled by the junction, while at higher voltages the bulk Properties of the CdS substrate effectively control the current. Because of the large thicknesses no negative resistance was found. Reverse breakdown voltage varied from 5 v, for junctions that were not heat-treated, to 100 v, for diodes that received the proper heat treatment. The rectification ratio, measured in the range of 2 to 10 v, varied from 300 to 3000. Capacitance- voltage measurements indicate a weak dependence of the junction capacity on applied voltage. The capacity was found to increase appreciably with room light illumination. The variation of capacitance with frequency is indicative of a p+-i-n structure. An open-circuit voltage of 0.4 v was measured under an illumination of 100 mw per sq cm. Under forward bias, the bluish-green edge emission characteristic of CdS was observed. No sharp rare earth emission line was observed, which is in contrast to our results using ZnS:Tb, where, under high-voltage excitation, the rare earth emission was dominat over the lattice emission. The absence of rare earth emission implies that either the nature of the rare earth ion is different at the het-erojunction than in the bulk or the probability of energy transfer to the rare earth ion is small. RARE earth elements are playing an increasingly important role in the Synthesis of materials for a variety of purposes, e.g., solid-state lasers, color television screens, and so forth. Interesting systems result when wide-band-gap photoconducting lattices are activated with rare earths. A study of the lumines-

Jan 1, 1969

THE slag performs two useful functions in open-hearth steel- making. First, it is the means of disposal of all the impurities, save carbon, which are removed from the charge materials in refining the steel, so it must be suited to receiving and retaining as much as possible of undesirable elements with minimum loss of iron and useful alloying elements. Second, the slag serves as a buffer between the flame and the bath and transfers oxygen to the metal at a measured pace contrasted with the violent and difficultly controlled oxidation of the bessemer process. At the same time, the slag is a thermal insulator that limits the rate at which heat can be delivered to the metal from the flame, and a heavy slag blanket thereby serves as a brake on production rates. It has been said with justification that the secret of good steel- making is to make a good slag and the steel will take care of itself. In a broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of: (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) Si02, MnO, MgO, and other oxides charged as such or introduced incidentally with ores or fluxes or by refractory erosion, and (3) lime charged or fed to the heat to neutralize the "acidic" oxides present (Si02 and P205). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined; and the control problem would be solved. Unfortunately, only a somewhat imperfect control over these factors is possible, so the operator must begin during the lime boil and continue through the refining period to discover and correct departures from the normal pattern of slag development. To do this as the heat progresses, the first helper must be able to make quick estimates of the composition and physical state of develop-

Jan 1, 1964

By Hugh Rose

THE properties of the company lie within the Pachuca district, State of Hidalgo, Mexico, connected by three railway lines with Mexico City, 55 miles southwest, and by two lines with Vera Cruz, 250 miles southeast. The ores were formerly divided by sorting into two classes, smelting and milling, the former averaging about 2 oz. gold and 335 oz. silver, the latter 0.12 oz. gold and 23 oz. silver. The smelting ores were sold to custom plants, principally the American Smelting & Refining. Co. at Aguascalientes. The milling ores were treated by the patio process at the Guadalupe Hacienda, at Pachuca. This patio was probably the largest in existence at the time and continued in active operation up to March, 1910. In January, 1910, the mines and patio were sold to English interests, represented by Camp Bird Limited. Two new companies were formed, the Compañia de Santa Gertrudis, S. A., to operate the mines, and the Compañia Beneficiadora de Pachuca, S. A., to build and operate a custom cyanide milling plant. (Fig. 1.) GEOLOGY The historical geology of the Pachuca district is described by Fred J. Pope as follows: 1. The most recent sedimentary rocks in the district belong to the Cretaceous period. 2. The Cretaceous rocks were penetrated by large intrusions of ande-site (referred to hereafter as primary andesite) which occur as elliptical dome-shaped masses, striking northwest-southeast. These andesite bodies are from 8 to 15 miles long and from 6 to 10 miles wide. 3. A period of erosion during which the contour of the andesite domes was changed. 4. Andesite flows (secondary andesite) which rest unconformably on the primary andesites.

Jan 8, 1916

The Carol concentrator of the Iron Ore Company of Canada was completed in 1962 and through expansions .has become one of the largest iron ore beneficiation plants in the world with a new feed capacity of 147,000 It (149,350 mt) per day. The Carol ore contains specular hematite and magnetite having a bulk density of 166 lb/cu ft (2660 kg/m3) It is crushed to 7 in. (178 mm) for feeding to autogenous mills for subsequent concentration by Humphrey’s s spirals. Mine ore is loaded into 150 It (152 mt) trucks by 10 cu yd (7.65 m3) shovels and then, at a transfer station, is loaded into side-dump rail cars of 100 It (101.6 mt) capacity. Each train is composed of twenty cars and operates completely automatically as it hauls the ore to the primary crushing station, dumps its loads, and returns to the loading station, a 11.5 mile (18.5 km) round trip. The primary crushing station is composed of two 60 in. by 89 in. gyratories installed in 1962 and 1972. Neither crusher has a grizzly ahead of it. Rail cars are dumped into 300 It (305 mt) pockets which contain splitters for spider protection. What few oversize boulders which do not go through the crushers are drilled and blasted. Liners in the dump pocket and the crushed ore pokcet under the crusher are manganese steel. Both crushers are direct driven by 700 hp (5 15 kw) motors, and the hardness of the ore causes them to pull almost their full power. Crushed ore drops into a 160 It (163 mt) pocket equipped with radioactive level control units for low-intermediate, and high level indications. The low level unit stops and starts the apron feeder, the intermediate unit controls the feeder speed, and a high-level reading stops the car dumping. Apron feeders are 72 in. (1. 82 m) wide and are variable speed from 12 to 52 fpm (3. 7 to 15. 8 mpm). They discharge to 60 in. (1.52 m) wide takeaway belts. Crushing capacity, nominal and maximum for each crusher, is 4, 000 ltph (4. 064 mtph) and 4,600 ltph (4,674 mtph). The crusher eccentric is removed by a conventional cart which travels on removable rails. Mainshaft removal and maintenance is done by 65 and 75/10 ton cranes. Mainshaft replacement requires eight hours, a usual time, but concave replacement requires only sixteen hours, a result of a fine maintenance organization. Mantle relining is done at grade next to a repair track. Zinc is used for backing both mantles and concaves. Both the electrical rooms and the dust collectors are located below grade,

Jan 1, 1978

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man&apos;s thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life&apos;s work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe&apos;s pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe&apos;s work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book&apos; on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe&apos;s ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man&apos;s thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life&apos;s work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe&apos;s pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe&apos;s work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book&apos; on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe&apos;s ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By J. Szekely, Robert J. Fisher

A formulation is Presented and solutions are given for the problem of transient heat conduction in a sphere that undergoes a spatially uniform radiative heat exchange with its environment. The solutions were obtained by the numerical integration of the appropriate Partial differential equation and are Presented in a graphical form by Plotting a dimensionless average temperature against the Fourier number with the radiation number as a paranreter, for various initial sphere and environment temperatures. In addition to these numerical results asymptotic analytical solutions are also given. PROBLEMS involving the transient heating or cooling of droplets and particles frequently arise and are of importance in metallurgical operations. Spray refining, vacuum degassing, high-temperature gas-solid reaction systems, and pebble heaters are but few of the numerous examples that may be quoted. The practical interest in these problems from a design or operational point of view is to evaluate the change in the particle temperature with the time given its physical properties, initial temperature, and that of the environment. At the high temperatures encountered the principal mode of heat transfer between the particles and their environment is by thermal radiation; in case of vacuum degassing due to the very low thermal conductivity of the gas space the convec-tive components are negligible and radiation is the only heat transfer mechanism. Although much work has been done on transient heat conduction problems, the special class mentioned here, in which thermal radiation is specified at the bounding surface, received little attention to date. One contributory factor to this situation may be the nonlinearity of the radiation term in temperature, which in general precludes the use of analytical techniques and requires numerical or analog solution of the appropriate differential equations. In fact the only solutions of general nature that are available at present pertain to semi-infinite media and slabs.&apos;-3 The work on which the paper reports forms part of a program aimed at the theoretical and experimental study of transient radiative heat exchange between particles and their environment. The purpose of the present paper is to develop a formulation and solutions to the problem of transient heat conduction in a sphere that undergoes a spatially uniform radiative heat exchange with its surroundings. The solutions, obtained by the numerical integration of the appropriate differential equations, will be presented graphically, by plotting dimensionless parame- ters covering the range of variables relevant to metallurgical interests, thus affording a ready reference for design calculations. In addition to these results, approximate analytical solutions are also given which represent asymptotes, corresponding to extreme values of the variables mentioned. FORMULATION Consider a spherical particle of radius, a, initially at uniform temperature, Ti (T measured on the absolute scale), having a thermal conductivity, k, density, , specific heat, C, and thermal diffusivity, a. At time = 0 let this particle be exposed to an environment which is at a temperature T, and subsequently let there be a purely radiative heat exchange between the particle and the environment resulting in a spatially uniform heat flux at the surface. If in addition to the above we make the assumptions that the sphere is a gray body radiator, homogeneous, isotropic, and opaque, and that the physical properties are independent of temperature, conservation of heat in the sphere may be written as follows: The boundary condition contained in Eq. [3] states that the initial temperature of the sphere is considered uniform, equalling Ti, whereas Eq. [4] is readily obtained from symmetry considerations. Eq. [5] expresses the continuity of the heat flux at the surface of the sphere, or in other words the condition that the rate of heat exchange between the sur-

Jan 1, 1969

By M. A. Torcaso, P. Raimondi

To study mass transport in systems simulating oil recovery processes, different porous media were saturated with a mobile (carrier phase) and a stationary phase. Slugs of carrier phase containing a small amount of solute were displaced with pure carrier phase. By analogy to the chromato-graphic processes, the velocity of the solute can be predicted from a knowledge of the partition coefficient and the saturation provided that equilibrium between the two phases exists. Equilibrium was found to exist for different porous media, solutes and rates. The conditions were varied over the range normally encountered in the laboratory and in the field. The longitudinal dispersion of a solute undergoing interphase mass transfer was also investigated. INTRODUCTION The production of hydrocarbons by gas cycling, enriched gas drive and C02 or alcohol displacement involves, among other factors, relative motion between two phases and compounds, hereafter called solute, which are soluble in both phases. The solute is carried forward by the faster flowing phase at a lower velocity than the average velocity of that phase. Retardation of the solute is caused by chromatographic absorption and desorption in the slower flowing phase and by the degree of departure from equilibrium. At equilibrium the concentration of solute in the two phases can be related by the equation* CSw = K Cso ,............(1) where C, and C are the concentration of solute in the aqueous and oleic phases respectively and K is the equilibrium ratio, or partition coefficient. Displacement theories must contain an explicit assumption with regard to equilibrium, i.e., whether the compositions can be related by Eq. 1. The existance of equilibrium depends, in general, on the relative velocity between the phases. Unfortunately, other factors such as gravity segregation and viscous fingering, also depend on velocity. For this reason, whenever effects of rate on displacement were observed,2-4 it was practically impossible to discern what caused them — lack of equilibrium or the factors mentioned above. Equilibrium between phases has been the subject of extensive studies in fields such as extraction or chroma to graphy. It has received only small attention in flow through the type of porous media encountered in oil production.5 For this reason a method was developed which makes it possible to study the movement of a solute as it is affected by rate, type of porous media, partition coefficient and carrier phase, but in the absence of segregation or fingering. The information obtained enables one to determine when the assumption of equilibrium can be made. Briefly, the method consists of (1) saturating the core with a mobile and an immobile phase, (2) injecting a slug made up of the same fluid as the mobile phase and a small concentration of mutually soluble solute, (3) measuring the lag and the peak height of the slug at arrival and (4) correlating these variables with fluid properties such as partition coefficient and mixing constants of the medium. PROPOSED MECHANISM The principles of chromatography are combined with the equation of longitudinal mixing to predict the velocity of a solute slug compared to the bulk velocity and the peak height of a slug.6-9 The equation so obtained is valid under equilibrium conditions only. Therefore, a comparison between experimental and predicted results will give a measure of departure from equilibrium. This work was done with either the oleic or the aqueous phase being immobile. For simplicity, the following development is based on the case where the oleic phase is immobile. However, the treatment is the same in either case.

Jan 1, 1966

By R. T. O’Brien, J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and Ni (11) and Co (Ilj concentrations. Results have been discussed in terms of adsorption of Ni (11) and Co (11) cations and hydroxide precipitates. Possible relationships between the experimental results and the formation of lateritic nickel deposits have been discussed. The adsorption of metallic cations to the surface of silicate minerals is of significance in many industrial and natural processes. In an earlier publication,&apos; the adsorption of Fe (111) to the quartz surface, a phenomenon of importance in flotation, was studied qualitatively using microelectrophoresis techniques. This paper reports the extension of this work to an investigation of the adsorption from aqueous solution of Co (11) and Ni (11) to the quartz surface. The adsorption of these metals was of interest for two reasons; firstly, the importance of such an adsorption process in the formation of nickel deposits by the lateritization of nickeliferous rocks, and secondly, the comparison of electrophoresis data for these metals, whose hydroxides precipitate in the pH range 7-8, with similar data for Fe (111) where the hydroxide first precipitates at pH 2.8. The development of laterites is essentially a near-surface geological process involving vertical and, in part, horizontal redistribution of elements derived from rock-forming minerals. This redistribution of elements leads to the formation of layers within the lateritic profile which are enriched in one or more of these elements and, depending on the nature of the original rocks, continued lateritization may give rise to iron ores, bauxites or nickeliferous laterites. The mechanisms discussed in this paper deal with the last mentioned type of deposit although the considered factors are applicable to laterites in general. Nickeliferous laterites are derived from basic and ultrabasic rocks containing ferro-magnesian silicates. These rocks may be partly or wholly converted to serpentinites. Besides their high Mg, Si and Fe contents, they also contain small amounts of Mn, Al, Cr, Ni, Co, Cu and Zn. The nickel content is usually near to 0.2-0.3%, but for economic use this must be increased during lateritization to over 1% and preferably over 2%. The zone of nickel enrichment is usually at some depth within the lateritic profile. Unpublished work by Mr. O&apos;Brien on nickel-bearing laterites in eastern Australia indicated four visually different types of material which were separated from crushed samples under a stereo-microscope. Although chemical analyses indicated that all four types of fragments contained 2-4% nickel and smaller amounts of cobalt, X-ray diffraction and optical studies revealed only quartz, hematite and chromite as well as, in one of the types, a serpentine mineral. No distinct, nickeliferous minerals were detected. Furthermore, it was possible to extract some 60% of the nickel content of the laterites with cold 0.5N hydrochloric acid. It was therefore postulated that much of the contained nickel was present as amorphous, adsorbed material. In considering this fact, as well as the problem of the actual method of transfer and fixation of elements within the lateritic profile, it was further postulated that the transfer of these elements probably took place partly as solutions and partly as colloids and that the fixation of these was caused by adsorption and flocculation. The existence of nickel in solution in water draining from serpentinites has been confirmed by Smurov.2 Although we have no evidence for the transportation of nickel in the colloidal state, it is well accepted that colloids are important in the formation of laterites. Previous work by Mr. Mackenzie&apos; has already indicated that iron may be adsorbed on quartz under conditions which could be expected in a lateritic profile, but no information was available for nickel or cobalt. Although adsorption possibly also takes place on minerals other than quartz, the latter is significant because silica is an important constituent of the silicate parent rocks. During lateritization, it is released to form free quartz and it is likely that it is initially extremely fine-grained. This would provide abundant opportunities for adsorption and it was de-

Jan 1, 1970

By B. J. Kochanowsky

TO improve blasting methods it is necessary to know how the explosive force acts and how rock resists this force. Because of the tremendous power developed within milliseconds and the great number of other factors directly affecting the technical and economic results, an analysis of the fundamentals of blasting theory is difficult. But since the rules used for layout design and for calculations of size of explosive charges are based on theoretical assumptions, complete knowledge of blasting theory has great practical importance in mining. Analysis of Blasting Theory: It is interesting to note the opinion of blasting experts with respect to contemporary blasting theories. F. Stussi; Professor of the University of Zurich, stated: "We do not have enough experience yet to change our army engineering regulations in blasting and base it on new fundamentals. It is our duty to collect more practical data and to do more research in blasting to close this gap." K. H. Fraenkel,2 editor of the Manual on Rock Blasting published in 1953 in Sweden and written by well-known Swedish, German, Swiss, and French blasting and explosive experts, said: "To the best of our knowledge no suitable formulas for civil blasting work are to be found in the American, French or German literature." Present blasting theory is based upon two assumptions. 1) The blasting force of explosive acts in concentrical and spherical form. 2) Rock resistance against the explosive force is directly proportional to the strength characteristics of the rock. The first classical formula based on theoretical fundamental in blasting theory for explosive charge calculation was introduced by Vauban, a military engineer who lived 300 years ago. It was Vauban who proposed the famous formula L = w3 q, where L is the explosive charge, w = line of least resistance, and q = specific explosive consumption proportional to the weight of rock. Later engineers used q as proportional to the strength of the rock. Since Vauban&apos;s time different suggestions concerning blasting theory have been proposed. However, the principles stated at that time so affected the thinking of later generations that his formula is still in use and practically unchanged. The first controversy concerned the form of crater. It was found that geological features of rock affected its form. The factor q was analyzed thoroughly by Lares3 and later by Ohnesorge," Weichelt,5 Bendel,6 and others, but the assumption remained that resistance against explosive force is directly proportional to the strength of the rock blasted. The greatest controversy, which has not yet been settled, concerned w. It was noted that w3 is more appropriate for long lines of resistance and w2 for lines of resistance less than 15 ft. Based on the assumption that the explosive force acts concentrically and spherically, spacings between charges were limited to distances not greater than the length of line of least resistance. Sometimes larger spacing is recommended, but this is due to the advantageous geological and physical properties of rock and not to the action of an explosive force as such. In addition to the classical formula, empirical formulas are used widely. These state that the explosive charge is directly proportional to the volume of blasted rock in cubic yards, and the amounts of explosive required are usually expressed in pounds of explosive per cubic yard of rock. Empirical and classical formulas are contradictory. In the empirical formula, but not in the classical formula, explosive charge is taken proportional to all three space axes: line of least resistance, spacing, and bench height. In spite of this contradiction, both formulas give good results. This is possible because as now practiced the explosive charge calculation for heavy burdens need not be highly accurate. Each, open pit or quarry, usually works with a certain relation between bench height and line of least resistance and between charge spacing and line of least resistance. When these relations are changed, however, the specific explosive consumption q changes greatly. This is one of the reasons why the principles on which the formulas are based appear to be incorrect. In addition to the formulas discussed, others exist and are based more or less on the same theoretical

Jan 1, 1956