Search Documents

By R. W. Hertzberg, R. W. Kraft

A study of the fracture behavior of unidirectwn-ally solidified Cu-Cr eutectic alloy was performed. Fractured whiskers, grain boundaries, and the interface between proeutectic Cr dendrites and the Cu matrix were the predominant failure initiation sites where grain size was larger. Strain induced void formation was restricted at lower solidification rates. This was attributed to a lack of adequate plastic constraint and a probable preferred orientation. A modification of the Crussard et al. model is presented to explain the appearance of "elongated dimples" on the shear fracture surface. A Cu-Cr alloy containing about 1.8 at. pct Cr solidifies by a eutectic reaction forming filamentary crystals of chromium within a continuous copper solid solution matrix.' Webb and Forgeng2 have shown by bend tests that the extracted chromium filaments, which are ordinarily curved and branched (due to random solidification), have the high strengths associated with whiskers. If an ingot of the eutectic alloy is unidirectionally solidified and appropriate control exercised over the thermal gradient, growth rate, and impurity level, the chromium fibers can be forced to solidify as fibers which are substantially parallel to the growth direction, Fig. 1. Uniaxial tensile tests on these straight chromium fibers extracted from controlled ingots3 have confirmed the earlier bend test results on curved fibers. Combining the facts that the strength and modulus of the chromium filaments are higher than the more ductile copper matrix and assuming that a "good bond" exists between the two phases, the Cu-Cr controlled eutectic system fulfills the requirements for effective fiber reinforcement of ductile matrices as established by studies on fiber glass reinforced plastics and other two-phase systems.4 Therefore, it was decided to study the fracture characteristics of morphologically simple specimens of chromium fiber reinforced copper (i.e., specimens of the controlled eutectic with substantially parallel reinforcing fibers) with the objective of establishing the dominant aspects of fracture. PREVIOUS WORK Comparatively little work has been done to understand the manner in which ductile alloys fail be- cause of the limited demand for this kind of information. Ordinarily ductility is specified for safety or similar reasons and when a part deforms plastically its useful life is terminated. In recent years, however, a number of investigators have begun to

Jan 1, 1963

By Robert M. Rudio

Montana is leading the way in the field of mined-land reclamation with new laws and new ideas. The Montana Department of State Lands is combining new legislation and practical application techniques to all mining operations in the state. Road building, stream relocations, or settling systems can be designed to meet the environmental problems. Mineral exploration now requires a new and closer look at drill site locations, road gradients, and exploration tools. The problems and costs of land rehabilitation must be thoroughly understood by the exploration geologist in order to satisfactorily conduct exploration in Montana.

Jan 1, 1975

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined in part for the sgstem Gd-Fe. Seven intermetallic compounds have been found at compositions corresponding to the following Gd-Fe ratios; 2:3, 1.2, 1:3, 2:7, 1:4, 1:5, and 2:17. The GdFe, com-pound has a congruent melting point above 18000C, whereas all of the remaining compounds melt incongruently, A eutectic exists at 13 wt pct Fe at a temperature of 860°C. ALTHOUGH an increasing amount of information is becoming available on the metallurgy of pure rare earth metals, relatively few studies have been made on alloy systems of the rare earths with the transition metals; iron, nickel, and cobalt. Even less data are extant on gadolinium alloys although it could be expected that such alloys might possess interesting structural and magnetic properties. In this paper, we report investigation of the gadolinium-iron alloy system. Studies on systems containing nickel and cobalt will be presented in subsequent papers. Previous data on gadolinium-iron compounds have been reported by Endter and Klemm1 and Jep-son and Duwez.2 Both reports agree on the existence of the GdFe2 phase, which crystallizes with the C-15type structure (face-centered cubic). This is in accord with results of the present work. EXPERIMENTAL The gadolinium metal used was prepared by met-allothermic reduction of high purity gadolinium fluoride. A typical analysis of the metal thus produced indicated the principal impurities to be oxygen, 0.24 pct, and tantalum, 0.2 pct. The iron metal used for alloying was a reagent grade material. Alloys were prepared by arc melting mixtures of the respective metals. Appropriate quantities of the two component metals were carefully weighed, blended and compacted. The compacts were then melted in an arc furnace consisting of a water-cooled copper hearth plate and a water-cooled tungsten-tipped counter electrode contained in a brass vacuum chamber. The furnace was evacuated to an absolute pressure of less than 1 with the leak rate established as being less than 20 per min. The furnace was then back-filled to a pressure of 25 mm of Hg, with a 75 pct He-25 pct Ar mixture. Arc melting at 25 v and 300 amp was maintained for about 30 to 60 sec until the entire visible area of the sample became molten, by which time surface tension had drawn the molten metal pool into a large bead. After allowing the furnace to cool, the alloy button was inverted and the melting process repeated. A series of melts was made covering entire composition ranges from 100 pct Gd to 100 pct Fe. All samples were examined metallographically in the as-melted condition. As the phase diagram became rationalized, and differential thermal analysis had given indications of temperature arrests, annealing was carried out in vacuo or in argon. Generally, compositions containing more than about 60 pct Gd were heat treated at 750°C and alloys containing less than this quantity of gadolinium were annealed at 1000°C. Prolonged annealing times were of the order of 100 to 200 hr. Metallographic examination was repeated on the annealed materials. Although little material loss was noted during alloy preparation, chemical analyses were made on all specimens prepared. The following standard, analytical techniques were used. Samples were dissolved in hydrochloric acid; insoluble material was filtered off, ignited and fused with potassium pyro-sulfate. The cold melt was leached with dilute acid and the solution thus obtained added to the main sample solution. Gadolinium was always determined gravimetri-callv as oxide from oxalate ignition. Iron was removed from an aliquot sample by electrolysis on a mercury cathode at approximately six volts. Gadolinium in the iron-free electrolyte was then precipitated as oxalate which was subsequently ignited to oxide. Iron was determined volumetrically in an aliquot solution by reduction with stannous chloride fol-

Jan 1, 1962

By P. G. Sprang, S. Rosen

The Y-Al- C ternary phase diagram for the com -position range from 55 to 100 at. pct Y and for a temperature of 950°C has been constructed from metallographic and X-ray diffraction data. The significant features of the isothermal section which is presented are the small solubility of aluminum in the binary Y3C phase and the presence of a ternary carbide phase with a small homogeneity range around the composition Y3AlC. The similarity in structure and composition between these two carbide phases is discussed in the light of the misci-bility gap which exists between room temperature and 1300°C, which was the temperature range studied. THE occurrence and stability criteria of ternary T3BC, carbide phases having the L'12 structure and the general formula T3BCx have been discussed in detail by stadelmaier1 and more recently by the present authors., Stadelmaier found many representatives of these phases formed between the T metals Mn, Fe, Co, and Ni and the B metals Mg, Al, Zn, Ca, Ge, Cd, In, Sn, Hg, T1, and Pb. The present authors reported on a new series of iso-structural carbide phases formed between the T metals of the Sc group and the B metal, aluminum. These new phases are unique in that many of the Sc group elements form stable binary carbide phases which occur about the composition T3C and which crystallize with a structure similar to that of the T9BCx ternary carbide phases. Furthermore, these binary and ternary phases are found to coexist in equilibrium with each other. The similarity in structure and composition between, for example, Y3C and Y3AlC in the light of the mis-cibility gap which had been found to exist between these two phases indicated a need for a more thorough knowledge of the phase relations which occur in alloys based upon these compositions. Consequently, an investigation of the phase equilibria in the yttrium-rich portion of the Y-A1-C phase diagram was undertaken. The limiting Y-A1 binary diagram determined by Lundin and Klodt3 and the results of Spedding et al.4 governing the Y3C phase were used as guides in , constructing the diagram. EXPERIMENTAL Alloys weighing about 10 g were prepared by arc-melting powder compacts made from the various components on a water-cooled copper hearth using a tungsten electrode in a gettered argon atmosphere. Good homogeneity was obtained by melting the alloys three times. The purity of the yttrium used was 99.9 pct (0.07 pct rare earths). The purity of the aluminum and the carbon was 99.99 pct. The results of chemical analysis on five representative alloys showed that losses during the alloying process were predominantly carbon losses and that in no instance did the measured concentration of this component differ by more than 3 at. pct from the intended composition. For this reason the alloy compositions which are reported are those of the charges prepared for melting. Three alloys which were analyzed for copper, tungsten, nitrogen, and oxygen compositions showed that no contamination had occurred either during casting or during the subsequent annealing treatments. For the major part annealing treatments were carried out on specimens which were placed in

Jan 1, 1965

By C. H. Stein

THE Pennsylvania Legislature, on March 13, 1837, passed an act authorizing the Lehigh Coal & Navigation Co. to construct a railway to connect the North Branch Division of the Pennsylvania Canal with the slack water navigation f the Lehigh River; the navigation company accepted this act on May 10, 1837. Edwin A. Douglas, chief engineer for the navigation company, located the route for this railway from White Haven to Wilkes-Barre, which was called the Lehigh & Susquehanna Railroad. The object was to transport coal from the Wyoming Valley, of Pennsylvania, to the Atlantic seaboard. This railway was considered a marvelous piece of engineering, as it included a tunnel nearly 13 mi. long, and a series of inclines, or planes, up which the cars laden with coal were raised from the vicinity of Ashley to the summit f the mountain near Solomon's Gap, whence they were taken to White Haven by rail. There the coal was transferred to canal boats. In June, 1862, floods almost completely destroyed the upper division of the canal, so on March 4, 1863, the Pennsylvania Legislature passed an act prohibiting its restoration, but granted a charter for the construction of a railway from White Haven to Mauch Chunk to connect with the line from White Haven to Wilkes-Barre, previously built. On March 16, 1864, a supplementary act was passed extending the Lehigh & Susquehanna Railroad to Easton, Pa. This completed a direct all-rail route from Wilkes-Barre to the New York harbor (by way of the Central Railroad of New Jersey). Up to this time, all freight and passenger traffic passed over the planes, but in 1866 and 1867 there was constructed what was known as the "back track" down the mountain side between Solomon's Gap and Ashley over which all the passenger traffic and empty cars thereafter passed; it is now known as part of the main line. For the handling of the heavy coal traffic, however, this would have involved a continuous climb from Ashley, 170.27 mi., from New York, to Solomon's Gap, 157.8 mi. from New York, or a distance of 12.47 mi., and a total ascent of 1,013.75

Jan 9, 1921

AT THE beginning of February the British Government announced acceptance of the American terms for funding the war debt, the main features-being as follows: Interest rate of 3 per cent. for the first 10 years and then 3 ½ per cent. up to the final extinguishment of the debt at the end of 62 years. The interest from the time since the loans were made to the actual beginning of the funding arrangement to be recomputed at 4 1/4 per cent. instead of the 5 per cent. rate now in effect. Congress ratified the contract respecting the British debt. The ship subsidy bill was relegated to the rear, which is indeed an end to the project. The natural consequence of this will be a liquidation of the Govern-ment's shipping business. The joint committee on the reorganization of Govern-ment departments made its report to the President. In general this seems to offer a well-considered plan for the coordination of Government service. The pro-posals respecting the bureaus that are particularly associated with the mining industry may be subject to criticism. According to the committee's plan, the Geological Survey remains in the Department of the Interior, but the Bureau of Mines and the compilation of the statistics of mineral production are transferred to the Department of Commerce. The Lausanne conference among the European powers came to an end early in February, without any treaty having been signed, owing to the refusal of the Turks to accept the ultimatum of the Allies. Theoreti-cally this left conditions in a state-of war between the Allies and Turkey. However, no actual movements have resulted. The French and Belgians continued to hold the Ruhr district of Westphalia, extending their lines and administration of the region. The Germans adhered to the policy of passive resistance. In the Parliament of Great Britain the French and Belgian policy was plainly declared to be unwise and dangerous. French and Belgian industries, moreover, were troubled by strikes among their own coal miners for higher wages. The Poles and Lithuanians engaged in border war-fare;. the civil war in Ireland continued. The rest of the world was quiet insofar as military operations are concerned.

Jan 2, 1923

By T. Rosenqvist

From the chemical, metallurgical, and mineralogical points of view, the importance of thermodynamic data for metal-sulphides and sulphur dissolved in molten metal has long been realized. Such data will give a basis for thermo-dynamic calculations of processes such as roasting and the distribution of sulphur between molten metal and slags. Furthermore, it will help us understand the chemical forces which tie sulphur to the metal and to the melt. Thermodynamic studies of solid sulphides and the equilibria between solid sulphides and metals have been carried out in a rather large number of cases by several investigators. An excellent review of this work is given by Kelley.1 On the other hand, very little is known about the thermodynamic properties of molten sulphides and of sulphur dissolved in molten metal. The only system which previously has been investigated in this respect is the iron/sulphur system. The purpose of the present investigation was primarily to obtain further data for metalisulphur melts and the system silver/sulphur was chosen, not because this system was expected to be of special interest in itself, but because the silver/sulphur system is a typical example of a metal/sulphur system. Because of the low melting temperatures, the work could be carried out without appreciable furnace and refractory difficulties. The sulphur in this system possesses a rather high escaping tendency compared to most other metal/sulphur systems. By the method employed (reaction with hydrogen to form hydrogen sulphide) this gives ratios Ph2s/Ph2 up to 0.30, which may be determined accurately. 'rhermodynamic investigations of the heterogeneous reaction Ag2S +H2 —+ 2Ag + H2S have previously been carried out by Pelabon,2 Keyes and Felsing,3 Jellineb and Zakowski,4 Wat-anabe,6 and Britzke and Kapustinsky.6 Their results are in rather poor agreement. Experimental Part PRINCIPLE In the present invehgation the escaping tendency of sulphur from the condensed phase was determined by the reaction: S + H2 = H2S The ratio Ph2s/Ph2 is at constant temperature, directly proportional to the escaping tendency of sulphur and to its chemical activity in the condensed phase. (This ratio will subsequently be denoted by H2S/H2.) From this ratio and its variation with temperature and with change in the com- position of the condensed phase, thermodyrlamic quantities such as free energy and heat of reaction can be derived. The apparatus used is shown in Fig 1. The silver/sulphur alloy was placed in a crucible inside a refractory tube and mounted inside the furnace to the left. The tube was a part of a closed, gas-tight system in which the gas mixture could circulate until equilibrium was established. Circulation was maintained by the glass propeller to the right, driven by an external magnet, and promoted by the chimney action of the furnace. The gas passed up through the furnace, down into the crucible where it came in contact with the alloy, passed rapidly up through a narrow tube and out of the hot zone. After equilibrium was established between the gas and the condensed phase, the composition of the gas mixture was determined from its density. In its circulation, the gas mixture passed through a chamber (lower right on Fig 1) containing a buoyancy-balance, where the density of the gas was determined by magnetic balancing. From the measured density,

Jan 1, 1950

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By P. G. Shewmon

If interfacial equilibrium is maintained at the interface between a growing precipitate and the supersaturated matrix, so that solute diffusion alone determines the growth rate, the precipitate shape should evolve toward that characteristic of the dendrites found in solidification. However, this shape is rarely observed in precipitation reactions proceeding at high temperatures where interfacial equilibrium is usually felt to prevail. Thus some other stabilizing factor must enter, to keep the interface smooth. It is shown that a slow interfacial reaction (low interfacial mobility) will stabilize the interface, while transformation stresses have a IN studying the kinetics of phase transformations such as solidification or proeutectoid precipitation at high temperatures, it is customary to assume that equilibrium exists across the interface and that the rate of the reaction is determined by the rate at which heat and solute diffuse to and from the interface. In the case of precipitation, such an assumption predicts an almost infinite rate of initial growth. It is generally stated that the rate cannot be infinite and that during some initial period the rate must be determined not by solute diffusion but by an interfacial reaction, i.e., transferring atoms across the interface. The duration of this much weaker stabilizing eFfect and impurities tend to enhance instability. It is also concluded that a sets an upper limit on the wavelength of the perturbation that can give instability. Thus initially all flat or smoothly curved particle interfaces will be stable even if their growth is diffusion-controlled. Proeutectoid precipitation in the Fe-C system is considered in some detail and it is shown that the experimental results can only be rationalized if the growth rate of ferrite in steel transformations is determined by a slow interfacial reaction for all hut a few orientations between the two phases. initial period has never been clearly established, but it is generally assumed to be too short to affect any measurable results.&apos; Several authors have pointed out that in the case of interfacial equilibrium any bump in the surface will grow out ahead of the planar interface due to the higher gradient in front of it.2j3 Thus the interface will be unstable with respect to an irregular interface with points (plates) propagating rapidly out ahead of the interface into the supersaturated phase. Recently, Mullins and Sekerka have given equations for the stabilizing effect of surface tenion.~ They found that for particles with a radius of curvature of 1 p or greater the stabilizing effect of surface tension will be completely overcome by a supercooling, or supersaturation, of as little as

Jan 1, 1965

By R. H. Wightman

The following paper describes current mining practices of the Riverside Cement Co. at its Crestmore plant, Riverside, California. For a number of years the Riverside Cement Co. obtained its raw materials by surface quarry operations but after these deposits were exhausted for equipment available at that time, the company started underground mining. Mine workings were begun in 1927 to 1930 for the recovery of limestone by block-caving methods. Geology The bed of limestone that is being worked is a metamorphosed and recrystallized limestone, which is generally white in color and from medium to coarsely crystalline. This bed is fissured by water courses that vary from minute cracks to large areas. The bed has also been cracked by intrusions along the footwall and hanging wall. These walls are coarse-grained, gray, quartz granodiorite. The strike of the deposit is north and south and it dips to the east at an angle of approximately 50°. The bed is approximately 1700 ft. long, 270 ft, thick at right angles to the dip at the middle of the deposit and tapers to a thickness of approximately 100 ft. at each end. Mining Methods The mine layout consists of four main levels with elevations as follows: 892 Collar of shaft. 800 Manway level used for ventilation, prospect purposes and as an entrance into the stopes. 700 Mining level where all material is extracted and on which are located the tapping grizzlies. This is the elevation from which all main cutoff stopes and undercutting work is started. 660 Haulage level where the limestone is drawn from transfer raises into the cars and is transported to the tipple by electric locomotives. 633 Level where all water is collected and which keeps the general water table below the working levels. A detailed description of the mine was given in U. S. Bureau of Mines Information Circular No. 6795, in June 1934. Current Block Development The first blocks to be caved were developed very much after the procedure followed in the copper mines of Arizona. This paper covers the ninth block to be caved. with a hard, tough rock like our limestone, it was found that some alterations in the development and control of dm, i, caving were. necessary to secure better crushing effect and provide more safety for such secondary blasting as is required. Sequence of Block Development 1. The fringes of the 800-ft. manway level are driven to confirm the diamond-drill information and serve to determine the final location and development required for the block (Fig. I).

Jan 1, 1946

By Robert S. Schecter, Mark P. Walsh, Michael J. Humenick

In recent years in situ leach mining has emerged as a viable technology for the recovery of uranium from strata in South Texas which contain relatively low concentrations of uranium ore. Because the ore bodies lie within ground-water aquifers, a significant determinant in the economics is the requirement that such aquifers be protected from contamination. Since ammonia is one of the constituents of the leach solutions now being field tested, one environmental problem to be resolved is the removal of ammonia at the end of mining. A second related question is the fate of the ammonia which is not removed by the restoration procedure. This paper considers the displacement and migration of ammonium in a flowing electrolyte with concomitant ion exchange. The ion exchange is an important feature since, during the solution mining phase, ammonium saturates the mineral exchange sites and must be removed from these sites. A mathematical model is used to simulate this process and the model is tested against the results of laborator.y experiments. It is found that the simulations are adequate if an appropriate selection of parameters is made. The model is then used to investigate the effect of cation composition and concentration of the restoration medium as well as dispersion on the overall effectiveness of the process. It is concluded that increasing the concentration of monovalent ions in a solution containing a mixture of both monovalent and divalent ions decreases the adsorption selectivity of the divalent ions with respect to all monovalent ions including ammonium. Thus increasing the ionic concentration of a restoration fluid by increasing the concentration of a nonselectively adsorbed (with respect to ammonium) ion may have a very limited benefit.

Jan 1, 1979

By Jeff Steinhoff

INTRODUCTION The Henderson mine utilizes a highly mechanized, continuous, panel-caving, mining system to extract ore from a deep, massive, molybdenite deposit. The mine is located 80.5 km (50 miles) west of Denver, Colorado. The mine surface facilities are located 3,170 m (10,400 feet) above sea level in a steep valley on the eastern side of the Continental Divide. Milling facilities are 24 km (15 miles) west on the western side of the divide at an elevation of 2,804 m (9,200 feet) above sea level. The ore- body is located approximately 3,000 feet south of the valley under Red Mountain. Access to the ore for men and materials is through a 915 m (3,000-foot) deep, 8.5 m (28-foot) diameter, vertical, concrete-lined, service shaft. Access from the mill is through a 15.5 km (9.6-mile) rail haulage tunnel. The mine is ventilated through an additional intake shaft and two exhaust shafts. Mine production at this time is 27,255 mtpd (30,000 stpd). The mine ventilation system supplies 1,038 cubic meters per second (2.2 million cfm) through approximately 60 miles of drifting or 2.7 tons of air per ton of ore mined. There are 130 fans in the mine in fixed locations and in vent lines with 6,900 connected horsepower in the mine. MINING METHOD AND LAYOUT The orebody is divided vertically into two major zones. The upper zone is the 8100-level production area. The bottom zone is the 7700- level production area which is in the early development stage. The rail haulage level at 7500 feet is common to both production zones. Each mine production zone consists of five associated sublevels. The cave undercut level is 16.8 m (55 feet) above the production level. Two boundary cutoff levels are located 44.2 m (145 feet) and 62.5 m (205 feet) respectively above the production level. The fresh-air level is positioned 15.2 m (50 feet) below the production level, and the exhaust vent level is 19.8 m (65 feet) below the production level. Horizontally, each production zone is divided into three panels each, 224 m (800 feet) wide. These panels are caved from south to north. As the caving in one panel nears completion, caving in the adjacent panel is initiated. Development for the caving panels is continuous so that the sublevels above the production level and the production level itself have a combination of development drifting and production-related activities. UNDERGROUND VENTILATION NETWORK The ventilation system is zoned in the same manner as the orebody itself. One major split of 600 cubic meters per second (1,270,000 cfm) ventilates the 8100-level production zone; one split of 100 cubic meters per second (210,000 cfm) ventilates the development of the 7700- level production zone; and one split of 165 cubic meters per second (350,000 cfm) ventilates the 7500 rail haulage level. The haulage tunnel requires an additional 188 cubic meters per second (400,000 cfm) of air. Development-drift ventilation is accomplished by hanging 1.0 m (3.5-foot) diameter steel ducting in the drifts with 40-horsepower, 0.96 m (38-inch) diameter fans supplying 9.4 cubic meters per second (20.000 cfm). The normal maximum length for these systems is 300 m (1,000 feet). The 8100-level production-area ventilation system is especially suited to a high level of mucking activity confined in a small area. Approximately 93 per cent of the mine&apos;s total production is transferred from the drawpoints to ore passes in 10 production drifts. The active area in each drift is 300 m (1,000 feet). Twelve 5-cubic-yard LHD units with Cat turbo- charged 170-horsepower engines are assigned to the area. Under these conditions, more than one LHD is assigned to a particular production drift. Adequate ventilation is maintained by making an air change every 97 m (320 feet) along the production drifts. Fresh air is brought into the production drifts from the fresh-air level through 1.37 m (4.5-foot) diameter raises. Air travels south along the production drift to the ore pass where it is exhausted down the ore pass to the exhaust level. The ore pass is followed by another intake which is followed by an ore-pass exhaust. At the south end of the production area, a series of exhaust fans maintain a southerly air- flow through the production level.

Jan 1, 1981

By Stephen Birch

THE Chitina mining district of Alaska is located at the headwaters of the Chitina and Copper Rivers. At present, the only producing min-ing properties are the mines of the Kennecott Copper Corpn. and the Mother Lode Coalition Co., which are situated 196 miles from Cordova the port of entry. The first claims, later acquired by the Kennecott Mines Co. and afterwards transferred to the Kennecott Copper Corpn., were discovered in 1900. The Copper River & Northwestern Ry., which connects the mines with tide water at Cordova, was completed in the spring of 1911. Contemporary with the construction of the railroad, aerial tram equipment was brought to the mines by pack train and a tramway, 3 miles, long, connecting Bonanza mine with the proposed railroad terminal, was finished, enabling shipments of high-grade ore to be made immediately on the completion of the railroad. A mill to treat the lower grade ore was begun the same year. The Kennecott company&apos;s holdings consist of 111 mineral claims. The Mother Lode Coalition Mines Co., which is controlled by the Kennecott Copper Corpn., owns 73 claims adjoining the Kennecott holdings. All data on operations and geology refer equally well to the Mother Lode property.

Jan 1, 1924

By Ivor Hawkes

A wide variety of borehole gages have been developed for measuring rock stress. They all operate on the principle that stress changes around a borehole result in deformation that can be measured by the gage and interpreted in terms of the stress change either by calculation or calibration. In general terms, gages that comply with the borehole deformations are referred to as “deformation meters” and those that restrain the deformations by reason of their rigidity are referred to as “stress meters.” The main advantages claimed for stress meters are: their “stress” sensitivity is much less dependent on the rock modulus than that of deformation meters, and they are clamped firmly in the borehole. The use of each of the borehole gages developed for stress determinations in rock in the main has been confined to the laboratory responsible for its development. To be generally accepted a gage must meet the following specifications : 1) Gages to be left in place to measure stress changes must be relatively cheap, and if possible recoverable, so that large numbers can be used to obtain an overall picture of the changing conditions. This, of course, is not necessarily the case for recoverable gages designed for absolute rock stress measurements where usually only one or two gages are involved. 2) For use in the adverse environmental conditions encountered underground, it is essential that gages be robust, stable, and unaffected by high humidity, corrosive water, or dust. 3) Highly qualified technicians are rarely employed specifically for rock mechanics studies in mines or on civil engineering sites and there- fore gages designed for measuring stress changes must be easy to set and

Jan 1, 1972

By R. G. Treuting, W. C. Ellis

D. Whitwham, M. Mouflard, and P. Lacombe (British Council Research Fellow, Labratoire du Professor Chaudron, Vitry-sur-Seine; Inqenieur de Recherches, Labratoire de Vitry; and Maitre de Recherches, Labratoire de Vitry, Professeur Adjoint de Metallurgie, Ecole des Mines, Paris)—The authors&apos; work is of great interest in bringing out the geometrical relations existing between twinned lattices, and for the notion of a coincidence super lattice developed from this. We should like to point out that a similar idea was put forward by Friedel8 in his book on the subject of lattice merohedrism "merihedrie réticulaire:"—When two crystals A and B are twinned with respect to a mirror plane, there exists a common superlattice, "réseau periode," which is independent of the contact surface between the two crystals. The volume V of this superlattice is a simple multiple of the volume v of the lattice of crystals A, or B, (Fig. 5). This "multiple cell" is defined by the twin plane (p q r) and a row of atoms [h k l] normal to this plane, the base being taken as the smallest unit (two-dimensional) of this plane. Two cases must be considered. First when the multiple cell, as defined, has no atom site at its center nor at the center of its faces other than (p q r), v the twinning index is defined by —. In the second v case, when one of the two above conditions does not v apply, then the twinning index is V 2v A more intuitive definition of the twinning index would be the proportion of atoms of C, which would coincide with those of C1 when the C, lattice is imagined to extend on the other side of the contact surface. In the case of cubic crystals, the twinning index

Jan 1, 1952

By Barrie T. Wells, Raghu N. Singh, Paul S. Buddery

Rockbolting and dowelling are important methods of ground control. Their effectiveness depends upon the compatibility of the support members and the geotechnical behaviour of the rock mass. Detailed geotechnical investigations are, therefore, necessary for the design of effective rockbolting systems. The study described in the paper was concerned with improving the effectiveness of ground control at Mount Isa Mine. The paper briefly reviews the design methods avail- able when choosing a rockbolting system with a view to identifying the most suitable method. Joint surveys were used for the geotechnical assessment of rock mass stability. These were interpreted with the aid of the stereographic technique of predicting the size and shape of potentially unstable blocks of rock in both the roof and side walls of excavations. The geology and ground conditions at Mount Isa are briefly described together with the current ground control techniques. The requirements for ground control have been investigated at representative sites by analysing typical modes of rock failure and using a geological predictive technique. An application of this technique to the selection of a support system in a shallow Coal Measures tunnel is also described. The paper concludes with a general discussion on the effectiveness of this method of site investigation for the appraisal of rockbolting support in mining and civil engineering excavations.

Jan 1, 1983

By Edgar Dunn

PART I.-DETERMINATION OF GASES IN SMELTER FLUES. IN 1907, upon arriving in Anaconda to take up work in the testing department of the Washoe Reduction Works, the. following problem was met at the car step, so to speak: complete and. exact analysis of gases, not only at the stack, but also in all departmental flues. Taken up to employ time not otherwise needed for regular testing department work, instructions were extremely liberal for a commercial plant, to the effect that accuracy should not be sacrificed to speed. In December, 1907, the work was temporarily transferred to the Great Falls Smelter, and some of the methods here given were there worked out. Differences in smelting operations at Great Falls and Anaconda, however, necessitated further investigations and the development of a new method for S03 determinations at the latter plant, where work was resumed in July, 1908, and completed about a year later. At the time of inception of the work, data (not only on percentages, but even on methods) were found to be meager in the extreme, for one or the other of two reasons: either entire lack of experiment at a large proportion of smelters, or disinclination on the part of the managements to divulge data of any description pertaining to either results or methods. In making determinations of gaseous constituents of flues, two methods are open to consideration: 1, the drawing out of a sample, and collection of the same as a whole, to be removed to the laboratory for later analysis; and 2, the absorption in situ on the flue of one certain constituent, disregarding others for the time being, or perhaps combining two or three in one determination. The first is generally the more rapid, but it is also the more inaccurate, method of analysis, even with special type absorption apparatus, being the more largely subject to error, both of reading, and also because of leakage during complicated manipulation in the laboratory. The amount used for analysis must also, because of limit of container, be small for the first method, and an average gas is very seldom obtained, necessitating for a fair average result a large number of determinations. Consequently, when we balance the time spent in a dozen determinations of short-time samples as against the time employed in making two or three long-time determinations of various constituents in situ, we are not so certain in our statement as to the relative speed of the two methods. Moreover, the method of analysis in the laboratory of 100 cc. of flue gas is satisfactory only when constituents thus determined are present in considerable quantity, results being simply approximate when determining such compounds as sulphur dioxide, sulphur trioxide, carbon monoxide and dioxide, and arsenic trioxide and water vapor, none of which are carried in all smelter flues in amounts in excess of (or even approaching) 1 per cent by volume. Special condi-

Jan 8, 1913

By Francis O. Blackwell

There are few industries in which power is more important to successful operation than mining, and none in which it is so difficult to ohtain power cheaply. Fuel is usually expeusive in mining districts, ana the ma chinery may be widely scattered and located in places difficult of access. The work is often so intermittent and variable as to prevent the economical use of steam. Mining operations are likely to exhibit accumulations of comparatively small and inefficient engines, numerous boilers and long lines of wasteful steam-pipes. Conlpressed air, as a means of transmitting power, is so handicapped by losses in the compressors and piping that it is limited to short distances and to the operation of apparatus requiring power, without regard to cost. To-day, electricity is rapidly replacing other methods of power-distribution, primarily because it is practically independent of distance. By selecting a potential proportional to the length of transmission, the cost of electric conductors and the e5ciency are the same for all distances within reasonable limits. For instance, a given amount of power can be delivered either 528 ft. away at 100 volts, or 50 miles at 50,000 volts, with the same total of copper per H.P. and with exactly the same loss of power in the transmissioo-circuk. This independence of distance permits the selection of the place most advantageous for power-development as a site for an electric power-plant, and the co~~centration there of the generation of all the power required within a radius of many miles. The powel.-site may be at a fall of water, if one is available, or a steam-plant can be built where fuel and supplies are cheapest, or where suflicient water is available for boiler-feed and condensing purposes.

Jan 1, 1904

By Warren B. Weeks

The year 1940 saw an increase of 20 per cent in oil production over the previous year—compared with a 16 per cent increase the previous year. In all, 25,790,380 bbl. were produced, an increase of 4,414,150 bbl, over 1939 and the largest production figure for south Arkansas since 1928. The older settled production continued to decline. Magnolia accounted for most of the increase, with aid from the other recent deep fields. During the year, 169 wells were drilled, 79 fewer than in the previous year. Of 131 wells drilled in proven fields, 18 were dry. Three of the 38 wildcats were pool openers. The drilling depth record was increased from 9028 to 9550 feet. Trend of Prospecting For the first time since 1936, the search for oil in the deep Smackover limestone slackened perceptibly; g dry wildcats ended in Smackover, 2 in. the underlying Eagle Mills; 7 penetrated Paleozoic beds, while 9 ended in Hosston, 2 in Glen Rose, 2 in Paluxy and 4 in Gulf. Geology The wells listed in Table 2 either resulted in the discovery of new oil pools or, because of their depth or location, afforded impor-tant stratigraphic or structural informa-tion. Fig. I is a general columnar and stratigraphic section showing the relation-ship of the strata within the Comanche series. The nomenclature shown was ac-cepted by the Shreveport Geological Society. It was subsequently published by Imlay,l who indicated probable correlations with other areas and presented evidence for the possible Jurassic age of the under-lying Cotton Valley and Smackover formations. New Fields Pouke.—On June 10, 1940, the Louark Producing Co. completed its No. I Sturgis, sec. I, T. 17 S., R. 27 W., in central Miller County, producing between 3583 and 3607 ft. in the upper part of the Paluxy forma-tion. The well flowed I00 bbl. of 3r.4&apos; gravity oil per day through Ns-in. tubing choke. This discovery resulted from seismograph work. Six other wells were drilled in the area, none of which found production in the original sand. One of these wells is producing from a sand 50 ft. deeper in the section. The others were abandoned. No further development is in prospect. Production is from lenticular sands of the upper Paluxy; 45,556 bbl. had been pro-duced by the end of 1940. There is structural closure against a fault to the northwest. McKanzie.—The Atlantic Refining Com-pany&apos;s No. I Bodcaw Lumber Co., sec. 29, T. 17 S., R. 23 W., eastern central La-fayette County, was completed June 8, 1940, as the eighth and farthest west of the Smackover (Reynolds o6lite) limestone pools. The well flowed 10 bbl. an hour of 58.6&apos; gravity distillate through an 1 1/64 Ma-in. tubing choke, with a gas-oil ratio of 8400:I.

Jan 1, 1941

By Warren B. Weeks

The year 1940 saw an increase of 20 per cent in oil production over the previous year—compared with a 16 per cent increase the previous year. In all, 25,790,380 bbl. were produced, an increase of 4,414,150 bbl, over 1939 and the largest production figure for south Arkansas since 1928. The older settled production continued to decline. Magnolia accounted for most of the increase, with aid from the other recent deep fields. During the year, 169 wells were drilled, 79 fewer than in the previous year. Of 131 wells drilled in proven fields, 18 were dry. Three of the 38 wildcats were pool openers. The drilling depth record was increased from 9028 to 9550 feet. Trend of Prospecting For the first time since 1936, the search for oil in the deep Smackover limestone slackened perceptibly; g dry wildcats ended in Smackover, 2 in. the underlying Eagle Mills; 7 penetrated Paleozoic beds, while 9 ended in Hosston, 2 in Glen Rose, 2 in Paluxy and 4 in Gulf. Geology The wells listed in Table 2 either resulted in the discovery of new oil pools or, because of their depth or location, afforded impor-tant stratigraphic or structural informa-tion. Fig. I is a general columnar and stratigraphic section showing the relation-ship of the strata within the Comanche series. The nomenclature shown was ac-cepted by the Shreveport Geological Society. It was subsequently published by Imlay,l who indicated probable correlations with other areas and presented evidence for the possible Jurassic age of the under-lying Cotton Valley and Smackover formations. New Fields Pouke.—On June 10, 1940, the Louark Producing Co. completed its No. I Sturgis, sec. I, T. 17 S., R. 27 W., in central Miller County, producing between 3583 and 3607 ft. in the upper part of the Paluxy forma-tion. The well flowed I00 bbl. of 3r.4&apos; gravity oil per day through Ns-in. tubing choke. This discovery resulted from seismograph work. Six other wells were drilled in the area, none of which found production in the original sand. One of these wells is producing from a sand 50 ft. deeper in the section. The others were abandoned. No further development is in prospect. Production is from lenticular sands of the upper Paluxy; 45,556 bbl. had been pro-duced by the end of 1940. There is structural closure against a fault to the northwest. McKanzie.—The Atlantic Refining Com-pany&apos;s No. I Bodcaw Lumber Co., sec. 29, T. 17 S., R. 23 W., eastern central La-fayette County, was completed June 8, 1940, as the eighth and farthest west of the Smackover (Reynolds o6lite) limestone pools. The well flowed 10 bbl. an hour of 58.6&apos; gravity distillate through an 1 1/64 Ma-in. tubing choke, with a gas-oil ratio of 8400:I.

Jan 1, 1941