Search Documents

By R. J. Towner

Tensile properties of Aluminum Powder Metallurgy (APM) products at 600°, 800°, and 1000°F were lowered by cold reductions of as little as 10 or 20 pct. The detrimental effect of cold work on yield strength at elevated temperatures increased with temperature. Heating cold-worked products at 850° to 1150°F removed the structural effects of cold work through the process of recovery and restored, at least partially, the strength at 600°F to the level of hot-worked material. Material containing 5 pct A1203 was recrystallized by cold reductions of 97 pct or more followed by annealing at 1100°F. Recrystallization lowered sharply the strength at room temperature, but raised the strength at 600°and 800°F relative to that of the cold-worked state The high strength of Aluminum Powder Metallurgy (APM) products at elevated temperatures'-4 is well-known. In this paper, some conditions of processing that can affect this important characteristic are presented. The following nomenclature will be used to identify different alloys: All of the above alloys are of the aluminum-aluminum oxide type made from milled powders of commercially pure aluminum with the exception of M486, which is fabricated from atomized A1-Fe alloy powder. The products made from milled powders are hardened by a dispersion of aluminum oxide par- ticles in the aluminum matrix, while the intermetal-lic compound FeAL is the dispersion hardening agent in M 486.' The process used for making all APM products involves the application of heat and pressure to form a compact from powder which is fabricated into an extrusion, sheet, strip, or wire by standard techniques. Probably the most common cold-worked APM product is sheet. Cremens, Bryan, and rant' determined the room-temperature tensile properties and the 600°F stress-rupture properties of XAPOOl and XAPOO3 sheet and reported that there was little difference between the as-extruded, cold-worked, and annealed at 1200°F conditions. On the other hand, Emmons6" found that the tensile and stress-rupture properties of XAPOOl and XAPOO3 sheet at 600" and 800°F were lower than those of extrusions. The tensile properties of XAPOO3 sheet were also determined at elevated temperatures by Doyle' and ~ayward.' According to Friske" and Kendal et a1.," cold working by swaging, rolling, and tube drawing reduced the tensile and creep-rupture strength of XAP 001 Recrystallized aluminum powder metallurgy products are rare because the dispersion in the aluminum matrix is usually too fine, uniform, and concentrated to permit recrystallization. However, Lenel12 was able to recrystallize wires made from aluminum powders containing about 1.75 and 3.0 pct oxide and found that the tensile properties at room temperature remained higher than those of annealed commercially pure aluminum because of the dispersed oxide particles. Westerman and Lenel13 found the kinetics of recrystallization of the powder products were very different from those of cold-drawn commercially pure aluminum wire. The alloy containing 3.0 pct oxide recrystallized to a very coarse grain size was more creep-resistant at 400" to 600°C (752" to 1112°F) than in the as-extruded, fine-grained condition, according to Ansell and weertman.14 Ansell and aenel" further studied creep at 500" to 620°C (932" to 1148°F) of recrystallized 1.75 pct oxide wire and confirmed the creep model of Ansell and Weertman. The present work is being reported for the fulfillment of the following objectives: 1) to show the effect of cold work on tensile properties at elevated temperatures;

Jan 1, 1964

By Harold L. Bare, Frank R. Barnako

Coal mining historically has been a. hazardous occupation but, in recent years, tremendous progress has been made in reducing accidental coal mine deaths and injuries. The purpose of this chapter is to discuss the basic principles of accident prevention as they are related to coal mining. Accident prevention fundamentals are no different for coal mining than for any other type of work. The fundamentals apply to all industries. Construction workers may be struck by falling tools and materials, and miners may be struck by falling slate and coal. Sailors may be trapped by shipboard fires, and miners may be trapped by mine fires. Railroad brakemen may lose hands and fingers positioning couplers, and miners may lose hands and fingers positioning couplers. Many other examples could be cited, but the point is that accidents that happen in coal mines are basically similar to accidents that happen in other industries. Thus, the basic principles for preventing accidents apply in coal mining as they do in any other type of work. COAL MINE ACCIDENT EXPERIENCE The US Mine Safety and Health Administration (MSHA) is the main source for accident experience data in coal mines. Coal mine operators are required, by law, to forward to MSHA monthly the number of fatal and disabling injuries, man-hours worked, and tons of coal mined. This information is compiled and published quarterly, with annual summaries, by MSHA. Trends in the number of fatalities and fatal injury rates are shown in Fig. 1. Major coal mine disasters, with number of miners killed, and dates of coal mine safety legislation are shown in Table 1. The fatal and disabling injury frequency rates for the coal industry are shown in Fig. 2.

Jan 1, 1981

By L. A. Roe, John Jan

Iodine is a soft, lustrous, grayish-black nonmetallic element with a density of 4.9. It is the least active of the four members of the halogen family. The other members are, in order of increasing activity, bromine, chlorine, and fluorine. Iodine is a solid at ordinary temperatures, while bromine is a liquid and chlorine and fluorine are gases. Iodine melts at 113°C and volatilizes at 184.4°C to a blue-violet gas with an irritating odor. It occurs in nature only as iodates and iodides or other combined forms. It was discovered by Bernard Courtois in France in 1811, who noticed its presence as an unknown substance in crude soda ash obtained from burning seaweed. Gay-Lussac recognized it as a new element and named it iode, from the Greek word "ioeides or iodes" for violet color (MacMillan, 1970). The world production is not known with any great certainty, but it is probably between 25 and 35 million lb per year, of which about 30% is consumed in the United States. Geology and Mineralogy Iodine compounds occur as a minor constituent as a mineral in the Chilean nitrate deposits and in solution in brines and seawater. According to the US Geological Survey, it is the 47th most abundant element in the earth's crust. The minerals lautarite, Ca (I03)3 (calcium iodate), and dietzeite, Cat (103)2 (CrO4), (calcium iodate-chromate) are found in Chilean nitrate deposits which are located in Antofagasta and Tarapaca provinces on the eastern slope of the coast range in a desert area. Various brines contain iodine compounds. Seawater contains about 0.05 ppm of iodine and some seaweeds will extract and accumulate it up to 0.45% on a dry basis. Some coals in West Germany also contain iodine compounds. The known and potential sources of iodine reported in 1968 are given in Table 1. Table 2 lists estimated world iodine reserves. Iodine has been recovered from brines in Java, Indonesia, France, England, and the USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. The indicated reserves and future resources of iodine are large but have never been adequately measured. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable. Markets and Prices Iodine and its compounds are generally marketed in the form of: iodine, crude; iodine, resublimed; calcium iodates; calcium iodide; potassium iodide, sodium iodide, and numerous organic compounds. Product Specifications Crude iodine, World market: 99-99.5% 12. Crude iodine, US produced, average: 99.8% 12. Crude iodine, USP XVII Specs: not less than 99.8% percent I2. Resublimed iodine is usually 99.9% and ACS specifications call for not over 0.005% total bromine and 0.020% nonvolatile materials (Anon., 1971). Prices, c.i.f. United States, for iodine have been steadily increasing from $1.18 per lb of crude in 1967 to $6.37-7.27 in January 1981 (Anon., 1981). In 1980 the price of iodine increased by 50%.

Jan 1, 1983

By W. van der Knapp

A theoretical and experimental ana1ysis is given of the change in volume of a porous medium due to changes in external and internal pressures. The result enable one to deduce directly the effect of large increlents in stresses. It is shown that the three-dimensional representation of the volume of a nonlinear porous system is a cylindrical rules surface, the generating lines of Which have a slope according to the solid rock compressibility. Analytical expression for such a ,surface is very simple. It follows that the bulk and pore compressihilities depend only on the difference between pore fluid and external hydrostatic pressure, i.e., the effective rock frame pressure. From measurements on a number of sandstones as well as limestones it can be conduded that for practical values of this effective frame pressure the pore compressibility falls in the range between the compressibility of water and that of undersaturated crude oil. In general, pore compressibility is found to be higher the lower the porosity. For a particular limestone reservoir pore compressibility and porosity could he related by means of a simple empirical formula. Results from the described study find a direct applicxtion in material balance calculations and in prob1ems of liquid flow through porous media. Since the elastic constants of the rock bulk material enter into equatiorls for velocity of acoustic waves, the results are also of importance for calculating rates of wave propagation in these media. It is shown for sandstones with 1.5 to -10 prr cent porosity that laboratory measured porosities may differ from those lender reservoir conditions by about I per cent of their value. The difference for low porosity limestotnes can be of the order of 10 per cent. The subsidence caused by elastic deformation of reservoir rock is shown to he very small. General formulas relating pore and bulk volume to external and internal pressure can be derived, as has been shown by Biot1, Gassmann2 and Geertsma.2 Their theories describe the differential change in volume caused by a variation in pore fluid tension and external hydrostatic tension. It has been known for a long timei that the stress-strain relations of a packing of spheres are essentially noninear. Our experiments show that for almost all reservoir rocks which arc elastically deformable the relation between volume and loading is also a nonlinear one, resembling that of a packing of spheres very closely. The behavior of these media is often described by using the linear stress-strain relations for small incremental stresses and strains in the vicinity of a pre-stressed condition." The present study differs from these considerations in that it enables one to deduce the effect of large increments in the stresses directly. In analogy to the stress tensor for a homogeneous body the stress tensor for a porous body can be written in the conventional way: where the tensor components, o, and t, represent the total forces acting on the faces of a unit cube of porous material. This tensor can be split into two parts. a hydrostatic and a deviatoric part, as follows2,3,1 where the component of the hydrostatic stress system, a. equals The hydrostatic stress causes a change in volume whereas the deviatoric stress system gives rise to a change in shape only. One of the difficulties in describing changes of volume occurring in reservoir rocks is that the relations connecting these volume changes with external and internal stresses are essentially non-linear. A complete description requires the bulk volume, V,,, as well as the pore volume,V,,. to be known as a function of both the changes in pore fluid tension (v) and the hydrostatic tension on the outer boundary.

By J. J. Pye, J. B. Drew

Mzasurements of the surface diffusion coefficients of metals have been made. Diffusion profiles for the Ag-Ag system were obtained by means of a radioactive point source and a precision auto-radiographic technique. The activation energy for silver self diffusion (=8.1 kcal per mole) is lower than that previously reported (-10 kcal per mole) on poly crystalline wire by Nickerson and Parker. The bresent data indicate an effect due to parasitic volume diffusion at temperatures above 500°C. RELATIVELY few measurements have been made of the surface self-diffusion coefficients of metals. Nickerson and arker' measured the diffusion of silver over the surface of poly crystalline wires and estimated that the activation energy was 10.3 kcal per mole. Winegard and chalmers2 carried out measurements on both polycrystalline and single crystal surfaces but did not report a value of the activation energy. They found, however, that at temperatures between 250" and 400°C the diffusion coefficients were on the order of lo-' sq cm per sec and that there was an acceleration of the migration of silver on the polycrystalline sample when a change of surface shape occurred. Winegard and Chalmers used an autoradiographic technique, hereafter designated ARG, and Nickerson and Parker used a surface scanning geiger counter in order to determine the diffusion profiles. More recently, Hackerman and simpson3 measured the surface self-diffusion coefficient of copper at a single temperature (750°C), and the value of the diffusivity (- 10-5 sq cm per sec) is in agreement with that given by jostein from his thermal grooving measurements. This paper reports the results of an investigation of the surface self-diffusion coefficients of silver over a large temperature range and describes the adaptation of autoradiographic (ARG) techniques for the determination of diffusion profiles obtained from a radioactive point source. EXPERIMENTAL PROCEDURE The experimental procedure is a modification of the method employed by Hackerman and simpson3 in their measurements on copper. A brief description of their technique is as follows: A radioactive needle which sinters to the surface during the diffusion an- neal serves as the source of diffusing atoms. After the diffusion run the needle is removed and the surface is scanned with a shielded counting arrangement. The diffusion profiles reported in this paper were obtained by a modification of the above procedure which employs a precision ARG technique. Previous investigations in this laboratory and elsewhere51B have shown that under carefully controlled developing conditions and by the use of calibration sources a linear relation exists between the concentration of the isotope and the photographic density for values below unity. The use of ARG under these conditions has advantages over the counter scanning method in that cumbersome shielding and requirements for great mechanical precision of the scanner are eliminated. Also the ARG gives a complete picture of the surface which is advantageous in studies of anisotropic diffusion. A recording microdensitometer having a 0.1 p wide slit was employed. At low temperatures the disturbing effects of subsurface radiations are negligible. The diffusion anneals are carried out in the cell shown in Fig. 1. The needle is formed by grinding down a 1.0 mm rod of high-purity silver until a tip of 0.2 mm radius or smaller is formed. This tip is plated withA"' which becomes the source of the diffusing atoms that are detected by ARG. The needle carrier and the crystal holder, Fig. 1 are constructed of quartz and ports are provided in the holder pedestal which allow free vapor circulation ((2.0 oz) and the carrier apron fits snugly over the crystal holder cap, insuring that the needle does not move and scratch the surface. Temperatures are provided by a stabilized tubular furnace which can be quickly positioned around the cell, thus bringing the crystal up to temperature in a time that is short compared to the diffusing times. The diffusion anneals range from 2 hr for the high-temperature samples to about 25 hr for those at the lowest temperature. The possibility of vapor transport of the radioactive metal as a contributing factor in the diffusion profile was investigated in two ways. One method was to suspend the needle directly over a dummy sample, raise the temperature, for periods of time equal to the diffusion times, and then take an auto-radiograph of the surface. Negligible radioactivity appeared. In the second method a thin slot in the crystal face on one side of the source provided a "cong path" for surface diffusion. If evaporation was the primary source of surface atoms the region of radioactivity around the source would be symmetrical. This was not the case. The profile dipped abruptly at the edge of the slot but on the other side of the source the usual diffusion profile appeared.

Jan 1, 1963

By K. A. Jackson, G. A. Chadwick, A. Klugert

The diffusion field ahead of a lamellar interfnce is analyzed using an electrical analog. A self-consistent solution is obtained for the shape of the interfnce and the diffusion field by an iterative process. The solutions presented here are for a 50-50 eutectoid or eutectic, The shape of the interface is found to he independent of growth velocity and lamellar spacing, and to depend on the relative values of interfacial free energies at the phase houndaries . The mode of growth of lamellar eutectics and eutectoids has been a subject of much interest for many years.1-4 Mehl and Hagel 1 have shown photomicrographs taken by Tardif when he attempted to determine experimentally the shape of an advancing pearlite interface; the results are completely ambiguous. Brandt' and schei13 have made approximate calculations of the composition ahead of a lamellar growth front. The shape of the advancing front and the composition distribution ahead of the front are difficult to calculate because one depends on the other. It is the purpose of the present paper to describe a method by which this calculation has been done. Lamellar-eutectic growth usually occurs under conditions where the growth is fairly rapid, and the interface temperature is close to the eutectic temperature. The growth rate is usually determined by heat flow. Eutectoid growth, on the other hand, can best be studied by quenching to some temperature, and allowing growth to proceed isother-mally. In both cases the growth is believed to be controlled by diffusion* rather than by the atomic kinetics of the transformation. This being the case, a single treatment of the diffusion equation will apply to both cases, provided the region of the interface in a eutectic may be considered to be isothermal. If a part of the interface could appreciably change its thermodynamic driving force by advancing ahead of or lagging behind the mean interface, then the two cases would not be similar. Eutectics normally grow in temperature gradients of the or-der of a few degrees per centimeter. The normal eutectic spacing is the order of a few microns. Part of the interface would have to extend many lamellar spacings ahead of the mean interface before it experienced sensibly different conditions. The interface temperature is usually a few tenths of a degree below the eutectic temperature so that temperature differences of the order of one-thousandths of a degree (a displacement of one lamellar spacing) would be unimportant. Protrusions large compared to the mean spacing do occur when one phase only grows into a eutectic liquid. This is usually a dendritic type of growth, and easily distinguishable from the lamellar mode of growth. A single treatment of lamellar growth will apply equally well to both eutectic and eutectoid decomposition. At the interface, which as shown above is essentially isothermal, the difference between the equilibrium eutectic temperature Teu and the actual interface temperature Ti, can be divided into two parts: 1) the composition varies across the interface, so that the local equilibrium temperature is not Teu; and 2) the interface is curved, so that the local equilibrium temperature is depressed according to the Gibbs-Thompson relationship. This undercooling can be written as Teu-Ti =?T = mAC(x) + a/r(x) [1] where ?C(X) is the departure of the composition at a point x on the interface from the eutectic composition, see Fig. 1, r(x) is the local radius of curvature at a point x on the interface, m is the slope of the liquidus line on the phase diagram, and a is a constant given by where s is the interfacial free energy, TE is the equilibrium temperature, and L is the latent heat of fusion. The calculations in this paper will be made only for the case where the phase diagram is symmetric, that is, the eutectic occurs at 50 pct, the liquidi have the same magnitude slope m at the eutectic temperature, and C,, the amount of B rejected when unit volume of a freezes, see Fig. 2(a), is the same for both phases. As shown in Fig. 2(b), the composition ahead of the a phase will be rich in B, the composition ahead of the ß phase will be rich in A. The composition at the phase boundary is the eutectic composition. The difference between the local liquidus temperature and the actual tempera-

Jan 1, 1964

By T. A. Rickard

Among the gold-deposits discovered in recent vears none is more extraordinary in richness or interesting in structure than that of the famous mine at Mount Morgan. At a time when but few Australian mines were known to the world outside the colonies, Mount Morgan was quoted as an occurrence, unusual not only in its origin (for it was said to be dye to geyser-action) but also in the purity of its gold. The mine is situated just within the tropics, twenty-six miles southwest of Rockhampton, in central Queensland. Queensland attained in 1889 the first place among the gold-producing colonies of Australasia, a position previously always held by Victoria. In that year Queensland produced 737,822 ounces, while Victoria cape second with 614,838 ounces. Of the four chief mining districts Rockhampton stood first, as the following figures show: Quartz crushed, Yield,. Average per ton, Tons. Ounces. Oz. Dwt. Rockhampton ,....81,138 340,669 4 4 Charters Towers,.. .. 109,328 165,551 1 10 Gympie,.....106,625 112,847 1 1 Croydon,.....29,423 51,156 1 15 It should be added that Queensland has but little alluvial mining, the total output from this source in 1889 being only 5044 ounces, none of which came from the four principal gold-fields. Leaving out Rockhampton, the output of which is practically that of the Mount Morgan mine, it will be noted that the more northerly goldfields show the highest average (Gympie being furthest from and Croydon nearest to the equator). This is largely explained, however, by the increased cost of milling, due chiefly to the want of water for batteries and the consequent economical necessity of selecting high-grade material only for crushing. During the year ending November 30, 1889, the Mount Morgaq

Jan 1, 1892

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson' have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,' have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By James T. Gow, Oscar E. Harder, Anton de S. Brasunas

This paper deals with the results obtained and the techniques employed in determining: 1. Liquidus and solidus temperatures of the HH and HT type heat-resistant alloys. 2. The relation of true temperatures (thermocouple) to apparent temperatures (optical pyrometer) for the molten HH and HT type alloys. This work was the outgrowth of needing to know something definite about these temperatures in order to study the effect of pouring temperatures, shake-out times, and heat-treatments on the properties of some heat-resistant alloys. The information developed is thought to be of interest to industry for guidance in foundry practices and the industrial heat applications of the alloys. This paper is based upon work that has been done for the Alloy Casting Institute at Battellc Memorial Institute. Liquidus and Solidus Temperatures of HH and HT Type Alloys Experimenta1 Procedures Temperature-time curves were obtained during the cooling and solidification of several HH and HT type alloys. The metal was melted in an Ajax high-frequency, induction furnace and poured into a core-sand mold for cooling. The temperature measurements were obtained by means of a platinum, platinum-rhodium thermocouple contained within a fused silica sheath, which was extended through the side wall of the dry core-sand mold to a point at about the center of the mold cavity, which was 3 in. in diameter by 5 in. deep. The cold junction of the thermocouple was kept in an ice bottle, and the temperature was recorded automatically on a direct-reading potentiometer recorder. Through a switching arrangement, the temperature recorded was checked occasionally with a portable Leeds and North-rup potentiometer indicator. Less than a 5°F. variation in the two instruments was always found. This is within the limit of accuracy of readings. The thermocouple used was checked for accuracy against a standard couple, both before use on this work and after completion of the work, by the instrument laboratory. Temperature-time Cooling Curves Fig. I is an enlarged reproduction of a part of one of the cooling curves over the temperature range of 2600' to 2200°F. for an alloy of the HT type with 0.45 per cent carbon, 16 per cent chromium, and 36 per cent nickel. This is a typically shaped cooling curve as obtained for the alloys. It will be noted that two temperatures "re shown on Fig. I for the liquidus temperature. It is thought likely that the higher temperature, A, at the point at

Jan 1, 1945

By W. Z. Price

The coal lands that the Nemacolin mine is to develop embrace over 8400 acres; the tract is oblong and its eastern edge is along the Monon-gahela river. As shown in Fig. 1, the mine is divided into two parts (the North mine and the South mine) by a 150-ft. barrier, which however, is cut through at intervals by haulageways. Each part is fed from seven main entries—a loaded track, an empty, a manway, and four return air courses. The loaded tracks converge at the shaft bottom but the empty roads maintain their identity throughout their length. With three intakes and four returns on either side, there is ample room for expansion of air and every facility for ventilating is provided. The four south air courses converge into two, crossing the shaft bottom, and then into one at the south side of the air shaft. The four north air courses converge in a similar manner on the west side of the same shaft. This convergence is accomplished by concrete arched

Jan 1, 1927

By P. K. Koh, H. A. Lewis, H. F. Graff

New data on the distribution of silicon between slag and carbon-saturated iron at 1600Oand 1700OC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1'700°C for slags containing up to 20 pct A12O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A12O3-SiO, slags over a range from zero pct Al2O3 to saturation with Al2O3, or CaO.2Al2O3. The upper limit of SiO2 is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/Al203 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al,O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al0 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al2O3 and of Al20,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO2 (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2. The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By John T. Norton, Matthew J. Donachie

Residual lattice strai?zs were produced in 2024 aluminum and ingot iron by uniaxial tensile deformation. These strains were rneasured on the original surface and ulith depth below the surface. The strains conformed approximately to those from a macroscopic stress distribution but they were not truly macroscopic in nature. The exact mechanism which apparently causes the coherently difi9,acting region of each grain to behave as if macroscopically stressed was not determined. MACROSCOPIC stresses in metals produce strains in the lattice which result in X-ray line broadening and line displacements. The latter effect can be utilized in a technique for determining stresses in metals as first shown by Lester and born.' Subsequent advances in technique have enabled the X-ray method of stress measurement to be satisfactorily applied to many problems involving residual stresses of a macroscopic nature, such as those due to welding, grinding, shot-peening, and so forth. In the case of stresses such as those described above, the correlation of X-ray- and mechanically determined data has been generally good. However, plastically extended polycrystalline metals have sometimes been reported2 to show line displacements upon release of the applied tensile load, yet the nature or origin of the residual lattice strains, rls, producing these displacements has never been clear. As will be pointed out, this lack of clarity regarding the macroscopic or microscopic nature and origin of these stresses casts doubt on the validity of results achieved by the commonly accepted techniques of X-ray stress measurement. This anomalous behavior requires clarification to remove the doubts concerning X-ray stress measurement. The present paper is the result of an investigation of the interesting behavior of such plastically extended polycrystalline metal bodies. The studies were originated to carry out the following tasks: 1) Observe whether a residual lattice strain is produced as a result of plastic extension and show whether any residual lattice strains produced can be related to the usual concept of a macrostress. 2) Examine the origin of any residual lattice strains observed. 3) Consider the implications or consequences of the existence of such residual lattice strains on the problem of X-ray stress measurement. THEORY 1) Lattice Strains. The theoretical developments necessary for the treatment of lattice strains and their relation to stresses follow from the classical theory of elasticity and have been adequately covered by arrett. For an isotropic solid under homogeneous deformation, it can be shown that, for uniaxial stresses where Dl is the macrostress acting in the longitudinal direction; E$L is the lattice strain in the plane defined by the surface normal and the longitudinal direction at an angle, , from the surface normal; ET is the similar strain in the transverse plane; E is Young's modulus; and v is Poisson's ratio. Eq. [2] is independent of angle + and Eq. [I] is a linear function of sin2, see Fig. 1, and can be solved analytically for DL if E and u are known and EL is measured. Thus, a uniaxial macrostress will be indicated by a linear E,L vs sinZ plot and a

Jan 1, 1962

By Richard Borg

The partial molal free energy of Cd in each of the four intermediate phases, Cd3 Cu, Cd8 Cu5, Cd3Cu4, and CdCu2 is determined using the Knudsen vapor pressure technique. Measurements are made also within the two-phase regions, and thus the variation in FCd is now known across the entire phase diagram. The absolute values are all less the 2.0 kcal and increase regularly with increasing Cd concentration. The small absolute value of the free energy precludes the possibility of obtaining highly accurate values; nevertheless, the results are compatible with those previously reported for the liquid phase. Additional results are reported concerning the lattice parameters of the 6, E, and b phases. THE elements Cu and Cd combine to form four intermediate phases which are designated* and E and which include respectively the following inter metallic compounds: CdCu2, Cd3Cu4, Cd3 Cu5, and Cd3 Cu. The extent of each phase with respect to temperature and composition is shown in Fig. 1 which is the equilibrium diagram drawn according to Hansen.1 All four phases are brittle, and most probably are true intermetallic compounds. Only the crystal structure of the 6 phase has been thoroughly investigated.2,3 The structure is cubic and isotypic with y brass. The structure of Cd3 Cu has not been previously reported, It is hexagonal with a = 8.11 and c = 8.76 0.02Å and the structure is presently being determined.* The compounds Cd3 Cu4 and CdCu, have been each previously the subject of a single investigation. Cd3Cu, is presumed to be cubic4 with the space group Fd3m, whereas CdCu2 is hexagonal2 with the C14-type structure. Cu2 Cd is found by X-ray analysis to be hexagonat with lattice parameters a = 5.00A and c = 16.17Å. The material appears to be pure Cu2Cd as all reflections could be indexed on the basis of the single hexagonal structure. These values disagree with those of Kripyakevich and coworkers5 who report a = 4.96Å and c = 7.98Å. Their investi-

Jan 1, 1962

By E. J. Valyi

The purpose of the continuous casting processes is twofold: As the name implies, they aim at performing a heretofore intermittent operation continuously; in this respect, they tend to satisfy the appetite of the beast that modern extrusion plants and rolling mills have grown to be. The effort invested in the development of these methods bore rich dividends in economy and in the improvement of technical characteristics. The other purpose of many continuous casting methods is to reduce the number o-f operations mushrooming between the liquid alloy and the finished mill product, essentially by substituting adequate chill in comparatively small cross sections for one or more "breakdown" steps. It is this second tendency of continuous casting that justifies description of the Soro process within the frame of our symposium: although not continuous, the Soro method constitutes a means of converting molten metal into a nearly finished mill product. The Process The name, Soro, is a composition of initials and abbreviations, with no particular technical significance. The process originates in Switzerland; it was adopted by numerous European plants between 1937 and 1940 and is now being installed in this country. It is applicable to ferrous and nonferrous alloys of an exceptionally wide range of composition. It is capable of producing rod from 1/2 in. to approxi- mately 4 in. in diameter, or other simple solid shapes of corresponding cross-sectional area. , Fig. I shows schematically the succession of operations involved. A ring is cast in a two-part centrifugal-casting metal mold. The cross section of the ring may be round, hexagonal, rectangular or some other solid shape, with the exception of any contour that is undercut with reference to the mold parting line. As cast, the ring has a riser along its inner periphery, which is removed in the next operation, so as to leave the ring with a dean cross section. Following the removal of the riser, the ring is severed at one point and one end is bent outward, leaving a slight clearance between the two ends. The next step is straightening of the ring in a special device, forming a bar with a slight bend; this is followed by any one of the conventional finishing operations that are necessary to obtain forging rod, screw-machine stock or strip. The outstanding features of this procedure are: I. The cross section cast is the same or within a few per cent of the cross section of the finished product (except for fabricating into strip and wire). 2. All operations following casting of the ring are performed cold. Equipment The equipment required is simple and inexpensive. The casting machine is a conventional horizontal-shaft mold assembly, similar to those found in centrifugal-casting foundries. Fig. 2 shows a battery of three machines- with their protecting hoods .swung open. One of these machines,

Jan 1, 1945

By J. J. Stokes

Literature on the electrolysis of aluminum from cryolite melts and on the structure of these melts is surveyed critically. Data on density, freezing point, and other properties are reviewed. Theories of the electrolysis are examined in the light of these data. Two theories are presented which account equally well for the observations. ALTHOUGH the production of aluminum is a large-scale industrial process, consuming approximately 3 pet of all of the electric current generated in this country, the mechanism of the Hall Process remains a 70-year-old mystery. It is a remarkable fact that the aluminum industry, which was established largely through research and owes much of its growth to research, still employs as its basic process the one developed by Charles Martin Hall while he was still a young man working in a woodshed. There are, of course, modifications in detail and a tremendous expansion of the size of the units used, but basically the process employs carbon anodes and a carbon-lined iron vessel as a cathode for the electrolysis of alumina dissolved in molten salt. Of the almost infinite variety of salts available, the relatively minor Greenland mineral, cryolite, 3NaF.A1F3, is still the only one which gives good performance in the electrolysis. In the early days, the process was thought of as a simple one. The dissolved alumina dissociated and, during the electrolysis, the aluminum was carried to the cathode where it was discharged and collected in a pool of metal. The oxygen was carried to the carbon anode where it reacted to form primarily carbon dioxide together with some carbon monoxide. About the only virtue that can be claimed for this hypothesis is that of simplicity. The actual mechanisms must be tremendously more complex. This paper is devoted to a rather narrow part of the whole subject, namely, what ions are present in the bath, and by what mechanism the current is carried. The complexity of the literature on this system is demonstrated in Table I, which shows the ions postulated as being present during the process. This system is not easy to investigate. Cryolite melts at about 1000°C, so that all the investigations are at relatively high temperatures. Molten cryolite fumes in air, particularly if excess aluminum fluoride is present. The cryolite changes composition on heating at 1000°C, principally by reaction with moisture in the air, but apparently also by reaction with oxygen. Cryolite reacts with most of the customary materials of construction, and those that are not attacked by cryolite seem inevitably to react with molten aluminum. Graphite is the only common material that is inert to the electrolytic bath. Pure cryolite can be held in platinum. There is hope that some of the newer refractories will stand up in bath, and their development for this purpose would be a major advance in the field. The techniques to be discussed, then, are not the most advanced ones. Rather, they are examples of old standardized methods applied under difficult conditions. The principal methods that shed real light on the mechanism are density, electrical conductivity, freezing-point lowering, transport number, viscosity measurements, and reactivity of bath with carbon dioxide. The first measurement to be discussed is density. This procedure is relatively straightforward. A hollow platinum bob is suspended by fine platinum wire from an analytical balance into the melt being investigated. Density1-4 of the system sodium fluoride-aluminum fluoride is shown in Fig. 1. There is a maximum in the density near the cryolite composition, but actually the maximum is on the NaF-rich side of cryolite, close to the composition NaF - Na3AlF8. Density measurements are also useful in giving a clue to the nature of cryolite-alumina melts.1, 4 On the first addition of alumina, density decreases, Fig. 2, although the density of alumina, either solid or liquid, is higher than that of cryolite. These density results indicate that the systems are not simple. A great deal of effort has been spent in measuring the electrical conductivity of molten cryolite and of cryolite with various additives. Conductivity measurements are quite easy for fused salts that can be measured in a dip cell, but no successful dip cell has been made available yet for cryolite. Recourse is had

Jan 1, 1959

By Robert B. Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 5th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 4th edition (1975) of Industrial Minerals and Rocks will clearly demonstate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Review. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. The Industrial Minerals Directory 1977, 1st ed., Metal Bulletin Books, Ltd., London, provides addresses of organizations in the field. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 4th edition of Industrial Minerals and Rocks. Most of these are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 18th annual meeting in 1982, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the US Geological Survey and the US Bureau of Mines. The two agencies publish many reports and maps on a variety of geological and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications: New Publications of the Geological Survey, US Geological Survey, 329 National Center, Reston, VA 22092 and New Publications-Bureau of Mines, Publications Distribution Branch, US Bureau of Mines, 4800 Forbes Ave., Pittsburgh, PA 15213. The US Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, 1970, and 1975. Four major series of publications by the Bureau are Information Circulars, Reports of Investigations, Mineral Trade Notes, and Minerals and Materials. The last two are particularly good for news of foreign developments. The Bureau of Mines Employee Directory, available at all USBM offices, lists addresses and telephone numbers for all offices as well as same for all commodity and area specialists.

Jan 1, 1983

By J. J. Arps

n approach to the study of the electrical properlies of drilling muds, their cakes and their filtrates was made by treating the drilling fluid as a porous medium. Lluring this study it was found that the weight pararneter was omitted from previous investigations on electrical properties. Patnode in 1949 made a similar approach to ,his investigation. His work showed that there was a variation of resistivity relationships with per cent Puid present in a given suspension. This present study ex-tends Patnode's investigation to one in terms of the solids fraction of the drilling fluids. Previous investigations were made on low weight muds where the effect of the rolids fraction was obscured. The following equationr were fitted to data taken from 94 field muds and 47 laboratory muds (see Tables I and 2). The parameter, C, is a complex function of the solidr content, or mud weight, of a drilling fluid. It was also found that for all drilling muds examined. A nomograph is presented combining Eqs. I and 2. INTRODUCTION It is generally recognized that the materials present in drilling muds affect the relationship between mud filtrate and mud resistivities. However, most electric log interpretations proceed with the assumption that the mud resistivity and temperature are the only important parameters needed to obtain a filtrate resistivity or a mud cake resistivity. Lamont1 suggests that only average relationships exist between mud cake, mud filtrate and mud resistivities. He indicates that there is limited accuracy when these intercorrelated factors are used since no other measure-able variable is apparent. A previous paper by Patnode indicates that drilling fluids may be considered to be a system of fluids in solid particles which may be correlated electrically in a manner similar to rock solids. 1 he equation for the resistivity factor. F = (per cent fluid) is satisfied for a given clay type in water, but the value of m varies as different materials are used in the water. The resistivity factor is not constant for a given amount of clay. As is suspected it varies as the solids fraction conducts electrical current. Since both weighting material and clay solids are present in commonly used drilling fluids, it is expected that both materials contribute to the variation of the m factor in Eq. 3. An extension of Patnode's work is presented in this paper to show some of the interrelations which exist between the resistivities of mud cake, mud filtrate and mud. Use of these data enable a more accurate calculation of mud filtrate and mud cake resistivities if only the mud resistivity and weight are measured. EXPERIMENTAL The measurements of mud weight, fluid and solids resistivity, alkalinity, and chloride content of mud samples were made in this research. Mud samples representing drilling fluids from 94 Louisiana and Texas wells (Table 1) and 47 laboratory-constructed systems (Table 2) were used in the experimentation. The measurements of the mud properties were made both in the field and in the laboratory. The tests on the properties of weight, alkalinity and chloride ion were standard tests as described by API specifications. The resistivity measuring devices were constructed in the laboratory for this study. For details on the resistivity equipment see Fig. 1. The fluid cell

By William R. Rumbold

When I was in South Africa during the latter part of 1904, there were three known tin-fields, which may be called the Cape Town, the Bushveld, and the Swaziland fields. The Cape Town Tin-Field. This district is situated near Kuils river, 20 miles west of Cape Town, and 5 miles from Kuils River station on the Cape Town & Stellenbosch railway. The deposits are in granite, intrusive in the Malmesbury beds, which are supposed to be of Silurian or Cambrian age. The granite, resisting denudation better than the surrounding shales, has formed low-lying hills, the highest of which, the Bottlelary Berg, is 1,510 ft. above sea-level. The rock consists of quartz, orthoclase feldspar, and biotite mica; tourmaline is also present. The feldspar occurs in large crystals. The rock is generally decomposed on the surface, and the decomposition sometimes extends as deep as 100 ft. This formation—granite intrusive in Silurian shales— extends for many miles to the northeast, but so far as I know the Kuils River deposits are the only ones now known to occur in it, though probably further prospecting will reveal other deposits. This particular discovery was accidental; alluvial tin being found in the course of boring for oil. The Kuils River Deposit. This deposit comprises both lode and alluvial tin. The lode strikes N-S., and dips about 30' E. into the hill. It is 5 ft. wide, and composed of dense white quartz, in which pinkish-gray cassiterite is distributed in large crystals. The vein also contains considerable quantities of wolframite. Fig. 1 is a rough plan of the relative positions of the lode and the alluvial deposit, the latter, as shown, following the course of a stream, while the lode crops out on the hillside ,

Jan 1, 1909

By Leonard C. Grimshaw

Diffusion of carbon from gases into iron has been the object of much research, because of its long recognized importance in carburizing processes, but the direct diffusion of carbon from steel into iron has received relatively little attention. Because of the increasing use of clad metals in industry, direct diffusion from steel into iron is becoming of practical importance. Therefore, the object of this investigation was to study the diffusion of carbon from several different kinds of steel directly into relatively pure iron, realizing that elements in the steels other than carbon might influence the rate of carbon diffusion. The previous work on diffusion of carbon into iron has been considerable, and includes many reports in foreign languages. This work has recently been well reviewed by Mehll and Krynitsky12 and the reader is referred to their excellent bibliographies. Methods of Study There are two main methods by which the direct diffusion of carbon from steel into iron may be studied. In one method, steel is first decar-burized in part, and diffusion of carbon then allowed to take place from the steel into the decarburized steel. This method is open to two serious objections: (1) the decarburized steel is not iron, but contains elements such as manganese, silicon, chromium or tungsten, which may be an essential part of the steel under study, and which may seriously influence the diffusion of carbon into the decarburized area; (2) there is from the start of diffusion an unknown carbon-concentration gradient between the steel and the decarburized area. Another method, which possesses neither of these disadvantages, is to study diffusion from steel into a thick plating of electrolytic iron. Herc the chief difficulty is to secure an electrolytic deposit of iron upon steel without introducing an oxide film at the interface that will interfere with diffusion. The author is able to deposit iron upon any kind of steel without introducing an oxide film at the interface, so that diffusion of elements from the steel into the iron is free to proceed unhindered.

Jan 1, 1938

By Leonard C. Grimshaw

Diffusion of carbon from gases into iron has been the object of much research, because of its long recognized importance in carburizing processes, but the direct diffusion of carbon from steel into iron has received relatively little attention. Because of the increasing use of clad metals in industry, direct diffusion from steel into iron is becoming of practical importance. Therefore, the object of this investigation was to study the diffusion of carbon from several different kinds of steel directly into relatively pure iron, realizing that elements in the steels other than carbon might influence the rate of carbon diffusion. The previous work on diffusion of carbon into iron has been considerable, and includes many reports in foreign languages. This work has recently been well reviewed by Mehll and Krynitsky12 and the reader is referred to their excellent bibliographies. Methods of Study There are two main methods by which the direct diffusion of carbon from steel into iron may be studied. In one method, steel is first decar-burized in part, and diffusion of carbon then allowed to take place from the steel into the decarburized steel. This method is open to two serious objections: (1) the decarburized steel is not iron, but contains elements such as manganese, silicon, chromium or tungsten, which may be an essential part of the steel under study, and which may seriously influence the diffusion of carbon into the decarburized area; (2) there is from the start of diffusion an unknown carbon-concentration gradient between the steel and the decarburized area. Another method, which possesses neither of these disadvantages, is to study diffusion from steel into a thick plating of electrolytic iron. Herc the chief difficulty is to secure an electrolytic deposit of iron upon steel without introducing an oxide film at the interface that will interfere with diffusion. The author is able to deposit iron upon any kind of steel without introducing an oxide film at the interface, so that diffusion of elements from the steel into the iron is free to proceed unhindered.

Jan 1, 1938