Search Documents

By V. V. Valleroy, A. J. Cornelius, B. T. Willman, G. W. Runberg, L. W. Powers

This paper reports the results of an investigation into the use of steam as a recovery agent. High oil recoveries by steam, as much as 100 per cent greater than by water flood, were demonstrated in laboratory linear cores. The principal mechanisms responsible for the additional oil have been identified as (1) thermal expansion of the oil, (2) viscosity reduction and (3) steam distillation. Although the first two also enhance recovery by hot water flood, they are effective with steam injection at lower volumes of produced fluids. Steam-zone residual oil saturation is independent of initial saturation. Recovery by steam is greater for lighter oils because they contain a greater fraction of steam-distillable components. Equations for the steam-zone advance in a radial homogeneous system are presented; these show the effect of reservoir parameters. The displacement in the hot liquid region moving ahead of the steam front can be estimated by a calculative procedure which is suggested. The method which takes account of the temperature gradient is applicable also to a regullar hot water flood. INTRODUCTION Considerable industry interest in the application of heat to petroleum reservoirs as a means of increasing oil recovery has been evident in the past few years. Three thermal methods which have attracted interest are (1) the injection of saturated steam, (2) the injection of hot water and (3) the injection of air into a formation to support combustion within the reservoir. Much has been published in recent years on underground burning, and there have been several papers on hot water injection. Although there are several early reports1,2 on steam injection, no recent experimental studies have been published on this recovery method. In our early thermal methods research, a marked improvement was found in oil recovery by steam injection compared with recovery by water injection in the same system. An investigation subsequently was undertaken to obtain quantitative information from which to evaluate steam injection as an oil recovery method. In addition, it was desired to investigate the recovery mechanism of hot water as compared with that of "cold" water and steam injection. An understanding of the mechanisms by which these processes operate would generally define favorable field conditions for their successful application. This paper reports the results of the laboratory study and suggests calculative approaches to estimate the field behavior of the steam-injection process. EXPERIMENTAL METHOD EQUIPMENT A schematic diagram of the equipment used for the displacement tests is shown in Fig. 1. Essentially, it consisted of a core with suitable means for recording temperatures, a feed system for injecting steam or cold or hot water, and a receiving train for condensing, cooling and measuring produced fluids. For the steam experiments, air-free saturated steam was piped from the boiler to the core face in insulated lines that were provided with steam traps and bleeds to remove any condensate formed in the lines due to heat losses. A 12-in. section of the line immediately ahead of

By James W. Shaffer

Aluminum is the most abundant metallic element and forms 8% of the earth's crust. Because of its chemical activity it does not occur in nature in a metallic form but principally in the silicates, feldspar, mica, shale, and clay. Bauxitic raw materials-bauxitic clay, aluminous laterite, and bauxite-develop from these aluminum silicate sources. Bauxite and aluminous laterite are naturally occurring mixtures of aluminum hydroxides and mineral impurities, and they are the major sources of aluminum. End Uses Bauxite is the basic ore of the aluminum industry. It is refined into aluminum hydroxide and calcined for feed stock to electrolytic smelters. Over 90% of the tonnage mined is refined and smelted into aluminum. The total tonnage consumed by other industries is small in comparison, but bauxite and alumina are important for the manufacture of refractories, ceramics, chemicals, abrasives, pharmaceuticals, catalysts, cements, dessicants, and flame retardants. Some aluminum-containing industrial products are made from clays and other materials but the majority originate from bauxite directly or from aluminum hydroxide and alumina refined from bauxite. Lateritic type bauxite is also used as building and decorative stone. Geology Mineralogy and Properties Bauxite is a mineral raw material composed principally of one or more aluminum hydroxide minerals and impurities of silica, iron oxide, titania, and other elements in minor or trace amounts. The important aluminum hydroxide minerals are gibbsite, boehmite, and diaspore. Bayerite, nordstrandite, and tucanite are naturally occurring aluminum hydroxides but are rare and not commercially important. Mixtures of gibbsite and boehmite are common, boehmite and diaspore less common, and gibbsite and diaspore rare. Gibbsite is aluminum trihydroxide. Boehmite and diaspore are aluminum oxide hydroxides and have essentially the same composition, but diaspore has a greater hardness and a more tightly bonded and denser atomic structure. Although not technically correct, the commercial terms trihydrate and monohydrate are frequently used to distinguish types of bauxite. If bauxite is all or nearly all gibbsite, it is referred to as a trihydrate ore; if boehmite or diaspore or a mixture of both are the dominant minerals, the bauxite is called a monohydrate ore. If substantial amounts of both gibbsite and boehmite are present, the bauxite is frequently referred to as a mixed ore. Properties of major bauxite minerals are shown in Table 1. Silica, iron oxides, and titania are major impurities always present in deposits of bauxitic raw materials.. Silica impurities usually occur as clay minerals, micaceous minerals, or quartz, but cristobalite and feldspar are found in some deposits. The most common clay minerals are kaolins; however, illites and chlorites are often found in small quantities. Varying proportions of aluminum, iron, and clay minerals make bauxite, aluminous laterite, ferruginous laterite, and bauxitic clay deposits gradational with each other. Hematite and goethite are the common iron mineral impurities in many bauxites. Magnetite and ilmenite occur in deposits derived from basic igneous rocks. Other iron minerals associated with bauxite are maghemite, pyrite, siderite, and marcasite. The titanium minerals found in bauxites are anatase, leucoxene, rutile, ilmenite, titaniferous

Jan 1, 1983

By Aloys H. Wohlrab

[THE conditions that govern the selection of a suitable type of detachable bit for the small isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may of be able to adopt the practice of larger mines because of necessary capital expendites for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has n yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the hit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests married out by Holman Brothers Limited1 with 7/8-in. show that when bit sizes are reduced from. 1 ½ in. 1 3/8 in., and 1 3/16 in., to 1 3/8 in., 1¼ in., and it' in., respectively, the volume of the hole is15 per cent less and the drilling speed 4q per cent higher. Recent tests by the United States Bureau of Mines2,3in hard, uniform basalt showed that a reduction in average gauge from 2.077 to 1.826 in., a difference of 0.251 in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and I4° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in]

Jan 1, 1942

By D. L. Garthwaite, F. M. Stewart, F. K. Krebill

Pressure has been maintained in the Elk Basin Ten-deep reservoir since the initiation of inert gas injection in Sept., 1949. Oil is being produced under conditions favorable for gravity drainage, including high angle of dip, appreciable structural closure, and fairly good per~neability. Results being obtained are high per cent recovery of oil-in-place, sustained field productivity, reduced operating problems, and recovery of plant products. The high recovery has been calculated by alpplication of the gravity drainage theory described in an earlier AIME paper.' It is also confirmed from field performance by comparing nil recovery to date with gas cap spuce voided. GENERAL INFORMATION The Elk Basin field lies in Park County, Wyo., and Carbon County, Mont., approximately 50 miles east of Yellowstone Park. Located at the northern end of the Big Horn Basin. the field is situated on an elongated asymmetrical anticline (Fig. 1). The pressure maintenance project covered by this paper involves the Embar-Tensleep reservoir in this multi-pay field. Discovered in Nov., 1942, it has a proved productive area of over 6,300 acres. It consists of the 210-ft thick Tensleep sandstone of Pennsylvanian Age overlain by 40 ft of Embar dolomite of Permian Age. The two formations apparently are in communication with each other and are produced as a common source of supply. As 98 per cent of the reserves are contained in the Tensleep sandFtone, in this paper the Embar-Tensleep reservoir will he called simply the Tensleep. The reservoir is found at an average depth of 4,900 it, is approximately 7 miles long and 2 miles wide, and has a maximum oil productive closure of 2,330 ft. The strata dip an average of 21" on the west flank and 45" on the east. There are presently 132 Tensleep wells in the field drilled on 40-acre spacing; of these, 17 are shut in because of high gas-oil ratio (GOR) and eight are gas injection wells. Rock characteristics and related information for the pay section follow: Porosity, avg 10.7 per cent Permeability (air) from cores, avg 118 mds Permeability from PI'S 91 mds Connate water, avg 8 per cent Initial pressure (-400 ft) 2,234 psia Pressure April 1954 (-400 ft) 1.327 psia At high structural positions much of the better sandstone has connate water content of only 2 to 5 per cent as indicated by the coring of wells with oil in nearby Tensleep fields. In special imbibition tests, samples readily imbibed oil but repelled water. In tests on crushed samples, the sand grains rapidly settled in oil and carbon tetrachloride but formed a stable unsinking floc in water. This information indicates that the Tensleep sand is preferentially oil wet. The oil produced averages 29' API gravity and has a high sulfur content. Extensive sampling and testing have established the fact that characteristics of reservoir oil in this field vary greatly with structure, see Fig. 2. Additional detail on the variation of oil characteristics with structure at Elk Basin may be found in Reference 2. At original reservoir pressure the oil was undersatu-rated with gas, the bubble point being 1,250 psi at the crest but only 500 psi at the lowest elevation sampled. As noted on Fig. 2, other fluid properties—reservoir volume factor. solution ratio, gravity, viscosity, and hydrogen sulfide content—likewise vary greatly. These variations complicate mathematical analysis, for it is necessary to average these characteristics in order to enter them into reservoir engineering expressions. To further complicate analysis, sand-face pressure also varies greatly because of the increase in fluid head down structure. As an approximation, average properties under initial conditions may be read from Fig. 2 at the -450-ft elevation.

Jan 1, 1956

By Philip N. Adler, Harold Margolin

Univariant equilibria between the Ibcc, IIhcp, and UIfee phases of thallium have been determined and indicate a triple point at 110°C and 37 kbars. Calculated II —I transformation curves are compared with the experimental. Transformation volumes and/or enthalpies are calculated and enthalpies are compared with available data. ThE triple point of solid thallium has been reported by Bridgman as 153°C and 38 kbar.' More recently, Jayaraman et at.2 have reported the triple point as near 115°C and 39 kbars. Meyerhoff and Smith,3 assuming the elevated-pressure modification of thallium is fcc, as Kaufman suggested,4 and that it is continuous with the room-temperature fcc phase in the Tl-In system, have used pressure data up to 5 kbars to predict the triple point at 162°C and 35.8 kbars. Piermarini and weir5 have indeed found the elevated-pressure phase to be fcc. The effect of variations of pressure and temperature in the IIhCp — Ibcc transformation in thallium have also been reported by werner6 and more recently by Ponyatovskii.7 The work reported here is part of an investigation of the effects of temperature and pressure on the Tl-In system. I) EXPERIMENTAL PROCEDURE The onset and progress of transformation were determined by changes in resistance. A commercially available tetrahedral-type pressure apparatus was used. Specimens of 0.060 in. diam, representing 0.63 pct of the cell volume, were encased in AgCl and mounted in pyrophyllite, as shown schematically in Fig. 1. It can be seen that the specimen is in series with the graphite furnace. Resistance changes of 0.1 pct could be detected with a Kelvin bridge. Resistance of the sample was of the order of 1 milliohm. Other pertinent details in regard to calibration and cell-assembly design are given elsewhere.' Temperature calibration of the cell was carried out in two ways as a function of input wattage. Through a hole drilled in the graphite furnace, a chromel-alumel thermocouple was inserted into the AgCl to a point 0.010 in. from the sample, with the

Jan 1, 1964

By C. F. Nagel

This paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. Heat Treating Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this irnprovement may be illustrated by some typical properties of dura-lurnin (Table 1). It is essential that the material be in the wrought condition in order to obtain rnaximum heat-treatment effects. In the case of duralumin, the process consists of heating the metal to a prescribed temperature and then quenching it. Immediately after quenching, the material is relatively soft though not as soft as in the annealed state. If allowed to stand at room temperature, the material changes, increasing in hardness and strength without loss of elongation, but at the expense of the plasticity. This action is very rapid at first, gradually diminishing in intensity and to all practical purposes being completed in about four days. This process of hardening is termed

By L. Eaton, A. W. Last, J. L. Stevens

COPPER ore from Kennecott Copper's Ray mine, about 60 miles southeast of Phoenix, Ariz., is concentrated at the company's mill at Hayden, some 18 miles south of the mine. The Hayden mill is currently treating 16,000 tons of ore per day by flotation, using raconite, a crude butyl xanthate, as a collector for the sulfide copper minerals and lime as a pyrite depressant.1 The ore contains significant amounts of nonsulfide copper minerals, but recovery of these values has been low. The Hayden mill is now being modified to provide for treatment of future ores by leach- precipitation-flotation (L-P-F). This modification, costing about $5 million, is expected to reduce the loss of nonsulfide copper values and improve overall copper recovery by an additional 2 lb per ton of ore.

Jan 11, 1957

Planning for a surface coal mine includes selecting the best means and equipment for uncovering the coal, loading it, and transporting it to the preparation plant. The machines and methods that will ensure optimum production will depend upon the location and characteristics of the seam to be mined. Stripping Techniques The choice of stripping units is influenced primarily by the system of mining, such as contour or out-crop mining as contrasted to mining in a region of rolling terrain with relatively flat upland surfaces. Factors such as the life of the mining operations production requirements, types of overburden, local and regional dip of coal, and land reclamation are other important considerations.

Jan 10, 1967

By William Fink

THE constitution of the aluminum-cobalt alloys has been the subject of relatively few investigations. Brunck1 analyzed the residue which remained after treating the 17 per cent cobalt alloy with dilute hydrochloric acid. The results of the analyses indicated the existence of a compound Co3Al13. Guillet2 published a liquidus for the aluminum-cobalt system which contained two maxima corresponding to CoAl6 and CoAl2 and two eutectic points at 30 and 74 per cent Co. The most extensive investigation of the system was carried out by Gwyer,3 whose results are summarized in Fig. 1. It will be noted that at the aluminum end there is a suppressed eutectic at 644° C. By extrapolation of the duration of the eutectic arrest to zero, the composition of the compound was placed at Co3Al13. Another thermal arrest was noted at 550° C., which Gwyer attributed to a peritectic reaction. The present investigation of the aluminum end of the aluminum-cobalt system is the eleventh of a series dealing with the constitution of aluminum; rich alloys prepared from electrolytically refined aluminum.4 Preparation of Alloys.-The alloys used in this work were all prepared from electrolytically refined aluminum, the analysis of which is shown in Table 1. In preparing some of the alloys, metallic cobalt (98 to 99 per cent) was used either directly or in the form of an intermediate alloy, the composition of which is given in Table 1. In order to obtain alloys of higher purity, cobalt was introduced into some of the alloys by means of chemically pure cobaltous chloride which was readily reduced by the aluminum. A small electric furnace with nickel-chromium heating elements was used in the preparation of the alloys.

Jan 1, 1932

By Albert Sauveur

Some writers believe that when austenite transforms completely into pearlite on slow cooling through the thermal critical range, such transformation does not imply the formation of any of the so-called transition constituents: martensite, troostite and sorbite. Might it not be claimed with as much justification that when water freezes it does so suddenly, solid ice being obtained without passing through the intermediate stages of ice and water? Obviously, regardless of the speed of solidification, this would be erroneous. Before reaching the completed solid condition, this must of necessity pass through an unbroken series of stages when the system consists of mixtures of water and of ice, the former decreasing and the latter increasing in amount. Are not these "transitionV stages in the freezing of water similar to the transition stages occurring in the transformation of austenite into pearlite? To clarify, let us consider in Fig. 1 the mechanism of the transformation of eutectoid steel from its austenitic to its pearlitic condition as it cools slowly through its thermal critical range. It is generally admitted that this transformation is the result of two distinct phenomena: (1) the allotropic change of gamma iron into alpha iron and (2) the crystallizing out of solution of the carbide Fe3C. Whether this crystallizing of Fe3C implies also its formation is immaterial for our purpose. In other words, whether it is the carbon in atomic dispersion which is present in gamma iron or molecules of Fe3C has no bearing upon the matter to be discussed. The transformation of gamma iron into alpha iron cannot take place suddenly. It must of necessity be progressive, regardless of the speed with which it may take place. At A, for instance, there would be present AB gamma iron and BC alpha iron. The distance MN does not refer to falling temperature, but to the passage of time. It may be assumed that the transformation takes place at a constant temperature (the Ar321 point). In a similar way, the crystallization of Fe3C out of the austenite solid solution must be progressive as depicted between M and N. At A there would be present AB gamma iron, BC alpha iron, CD carbon dissolved in gamma and in alpha iron and DE Fe3C. This condition may be described according to individual preference as martensite or troostite. To sum up, can the metal pass from condition

Jan 1, 1931

By W. H. Emmons

THIS paper is the third of a series treating of the relations of ores of the metals to igneous rocks. The first1 outlined the general problem; the second2 proposed a classification of lode ores, and showed how the distribution of the deposits is in a certain measure controlled by the contour of the roof of the parent batholith. A number of mining districts were discussed, the examples being selected chiefly from group 2 of the classification. The proposed classification of lode deposits, briefly stated, is as follows: 1. Cryptobatholithic: near hidden batholiths which have not yet been exhumed by erosion. 2. Acrobatholithic: in and near cupolas or domes of batholiths-the high points of larger underlying masses. 3. Epibatholithic: on batholiths, near their rims, but below eroded cupolas, or below the highest points of the roofs. 4. Embatholithic: among closely-spaced outcrops which probably are parts of a single batholith. The outcrops of invaded rocks predominate. 5. Endobatholithic: in and near roof pendants of large batholiths. The invading rocks predominate. 6. Hypobatholithic: in deeply-eroded batholiths, where even roof pendants, have been -eroded. Deposits of certain metals on the roofs of the batholiths are much more numerous in some positions than deposits of other metals, and the horizontal zonal arrangements of lodes of different metals are shown characteristically only in certain groups. In a large measure, also, the character of the fracturing and metallization is determined by, the-position on the roof, of the batholith.

Jan 1, 1927

THE metal iron has physical arid chemical properties which are some- what different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron the former being the ordinary form at room temperature. When heated above the "A2 point," 769 C (1416 F), the metal becomes nonmagnetic, and at the "A3 point," 911 C (1672 F), it undergoes a change in crystalline form to become gamma iron. 111 the range 769 to 911 C, it is sometimes called beta (ß) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 1392 C (2538 F), it changes into delta (d) iron, which is identical with beta or nonmagnetic alpha iron. Pure iron melts (in an inert atmosphere) at 1536 C (2797 F); the melting point is generally lowered by alloys or impurities. PHYSICAL AND THERMAL PROPERTIES OF IRON Many of the properties of iron undergo abrupt changes at the transition temperatures.1 For example, in heating through the A3 point, a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 16-1 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly with the range of stability of a given form, but this is not always true. For ex- ample, the specific heat reaches a sharp maximum at the A2 point al- though no transformation occurs. (See Fig. 14-1.) Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals that are liquid at the melting point of iron, only lead, silver, and bismuth refuse to dissolve to an appreciable extent. Table 16-2 contains a list of the common elements classified with respect to their solubility in liquid iron. Those which are very soluble or practically insoluble require no further discussion, but several of the nonmetals that are gases and exhibit limited solubility are of considerable importance to us and merit more detailed consideration.

Jan 1, 1964

By Charles Pack

Die castings may be defined as metal castings made by forcing molten metal, under pressure, into a metallic mold or die. It is necessary to keep this definition in mind to avoid confusing this process with other permanent-mold casting processes. The fundamental principles of the process have been known and practised many years. The simplest application is embodied in the modern linotype machine in which molten metal (usually tin-lead alloy) is forced under pressure into a metallic mold. The pressure is derived from a piston and cylinder immersed in the molten metal. Progress in the art of die casting may conveniently be divided into three groups: Machine for imparting pressure to the metal, material for the die or mold, casting alloys. The problem of delivering molten metal under pressure into a die is comparatively simple, when dealing with low-fusing-point alloys, as the alloys of lead and tin, but it is much more complicated when dealing with metals of higher fusing points, such as the alloys of zinc, aluminum, and copper. Although the art of die casting is comparatively new and, to a large extent, unknown, the records of the patent office are replete with patents on the subject. Fig. 1 shows the Underwood machine patented in 1902; this is probably one of the first machines designed for the production of commercial die castings. The relation of this machine to the linotype casting machine is clearly apparent. A cylinder and piston are immersed in the molten metal, the application of power to this piston forcing the molten metal, under pressure, into the mold or die. The Doehler machine, Fig. 2, patented in 1907, is based on the same general principles. This machine is used to a large extent at the present time, throughout the United States, for the production of zinc, tin, and lead alloy die castings. In the machine shown in Fig. 3, patented by Doehler in 1910, compressed air is used for forcing the metal into the die. In Fig. 4 is shown another of this type of machine. Here compressed air is applied to the surface of the molten metal to force it into the die. In a machine patented by Chandler in 1914, shown in Fig. 5, the

Jan 1, 1919

By N. A. Gokcen

The construction and operation of a simple and accurate vacuum-fusion apparatus are described in detail. Absolute accuracy of the oxygen analysis has been determined by the reduction of oxides weighed to 20.01 mg. The Bureau of Standards steel samples have been analyzed repeatedly, and their inadequacy for the acceptable range of oxygen is presented. The limits of interference of manganese, aluminum, and titanium, and the effects of tin and water-cooling of the furnace tube have been investigated in detail. ANALYSIS by the vacuum-fusion method consists of melting a sample in a degassed graphite crucible under high vacuum and extracting oxygen as carbon monoxide, and nitrogen and hydrogen as gaseous elements. The resulting gas mixture is analyzed for its constituents, from which oxygen, nitrogen, and frequently hydrogen may be determined within 1/2 hr or less. The history and summary of methods1-4 and extensive reviews of literature'.' for the determination of gases in metals have been published in detail. The foundation of the modern vacuum-fusion method of analysis was laid by Jordan and Eckman,11 and Oberhoffer and his associates.1, 10 Diergarten,11, 12 Meyer,13 Thanheiser et al.,14, 15 Ericson and Benedicks,16 Ziegler,17, 18 Sloman,16-23 Thompson et al.,24 and later many others contributed to the improvement, accuracy, and limitations of the method. In some investigations, however, the limitations of the procedure and the errors involved in the analysis require further critical examination and evaluation. In many apparatuses, lunnecessarily complicated and cumbersome features and elaborate precautionary measures do not have conclusive advantages. The purpose of this invest:igation was, therefore, a) to construct a very simple and accurate apparatus, b) to determine the absolute accuracy of results, c) to establish the limits of interference of manganese. aluminum, and titanium, d) to reexamine critically the reduction and recovery of oxygen from oxide powders of various sizes, and e) to evaluate critically the eight steels of the Bureau of Standards."' Apparatus The apparatus used in this investigation is shown in Fig. 1. It has been used for over three years, during which several modifications were made. A brief description of the apparatus is as follows. The transparent silica or Vycor tube, E, is joined to the Pyrex head, B, by mean of a face to face ground joint sealed with mercury. A similarly sealed ball and socket joint would also have been satisfactory. A standard tapered ground joint, successfully used by some investigators, was tried, but in the absence of grease or vacuum cement it was very difficult to disassemble the joint. The graphite crucible, G, 15/16 or l 1/8 in. OD, 2 1/2 or 3 in. high, 1/10 in. wall, shown enlarged in Fig. 3a, is made from the rods containing less than 0.08 pet ash. Two baffles, overlapping sufficiently to prevent spattering, are inserted in two opposite slots cut on a band saw. Two small holes in the baffles permit the temperature measurement of the melt. A second type of crucible, Fig. 2, G, shown enlarged in Fig. 3b, is also satisfactory, though not as convenient as the crucible shown in Fig. 3a. Somewhat similar but more elaborate crucibles with baffles were first tried by Ericson and Benedicks,'" but were abandoned in favor of a crucible with a stopper and a peripheral graphite powder filter. Various versions of their crucible with a stopper have later been used by other analysts, 10-27, 27-30 The crucible is packed directly in E, Figs. 1 and 2, with —35 + 48 graphite powder for shielding and insulation. A minimum layer of 7 mm of powder is necessary for keeping E cool and minimizing the blank. The first use of graphite powder was made by Sloman,10-23 Who found that —200 mesh was the most satisfactory. The author tried various size powders from +20 to —100 mesh and found that a) particles of 28 mesh or larger were not sufficiently insulating and were heated by the induction current, b) the powder finer than 60 mesh packed too much and did not readily permit the escape of gases even when the crucible was heated very slowly; hence, the powder was occasionally blown out of the side in the crucible and in the mercury pump. The optimum size powder is, therefore, 35 to 48 mesh size or 0.4 mm in average diameter. The furnace is designed to eliminate excessive amounts of

Jan 1, 1959

By David V. Ragone, James A. Craig, Richard E. Balzhiser

The Gibbs free energies of formation of UC2 and UC were measured by equilibrating two-phase mixtures of UC2 + C and UC, + UC with liquid bismuth. The measured equilibrium concentrations of uranium in the bismuth combined with available activity coefficient information yielded uranium activities in these two-phase regions. Measurements on UC2 were performed over the range 1015 to 1160 K and on UC over the range 1115° to 1165°K. The values obtained for UC2 are in excellent agveement with values determined using combustton calorimetry and low-temperature heat capacity measurements. The UC values are in fair agreement with the calorimetric values, differing by about 10 pct from the calorimetric determination. MUCH interest has been shown in the uranium carbides in recent years because of their potential as nuclear fuels. As nuclear reactor operating temperatures have been raised to increase thermal efficiency, new fuels have been required. The uranium carbides are of interest because of their high melting points, >2000°C, high thermal conductivity, and resistance to irradiation damage. The manufacture and use of uranium carbides are aided by a knowledge of their stability and reactivity under various conditions. In this regard the thermo-chemical properties of the carbides, i.e., heat capacity, heat of formation, free energy of formation, and so forth, are particularly important. A great amount of work has recently been done on the thermodynamics of the U-C system. Unfortunately, however, there has not been good agreement among the various investigations. This study of the free energies of formation of uranium monocarbide and uranium di-carbide in the temperature region 1100°-1200° K was undertaken to help clarify the situation. It should be noted that in the temperature range of this investigation, 1100°- 1200° K, the thermodynam-ically stable phase in equilibrium with graphite is U2C3, not UC2, Fig. 1. However, U2C3 is reported to be stable only under extremely low oxygen and nitrogen pressure. Although UC2 is metastable below 150O°C, it exists under most experimental conditions. It should also be noted that "UC," never exists as UC2 but with compositions near UC1.9. However, "UC2" will be used to designate the dicarbide phase except when the stoi-chiometry is necessary for clarity. METHOD The approach taken in this study of the free energies of formation of UC and UC2 was to determine the thermo- dynamic activities of uranium in the two-phase regions UC, + C and UC + UC, by equilibrating the two-phase mixtures with the liquid bismuth. When a mixture of solid UC2 + C is brought to equilibrium with liquid bismuth, the reaction that occurs is: Neither carbon nor UC, could be detected as dissolved material in the bismuth. The standard free energy for this reaction may be written: In the two-phase region UC, + C, Fig. 1, the thermo-dynamic activities of UC2 and carbon are unity. The activity of uranium in this region was determined by measuring the concentration of uranium in a liquid bismuth melt in equilibrium with the two-phase mixture. This concentration was then used in conjunction with the activity coefficient data of uranium in bismuth reported by Tien et al.' to determine the activity of uranium in the two-phase region, UC, + C. All of the quantities in Eq. [2] were then known, and the AG; (uc,) was evaluated. UC + UC2. For the studies involving UC + UC,, the reaction taking place when the two-phase mixture is brought to equilibrium with liquid bismuth is: The standard free-energy change for this reaction is given by:

Jan 1, 1969

By T. K. Perkins, R. N. Hoffman, O. C. Johnston

A simplified theory of viscous fingering in miscible systems has been developed. It predicts the correct functional relationship between pertinent variables and permits the calculation of the order of magnitude of fingering behavior for simple systems, such as linear or radial. The theory is based on the following four observations: (1) cross-flow takes place only near the ends of fingers; (2) the relative finger width is about 0.5; (3) fingers can be suppressed by transverse dispersion, the suppression being quantitatively described by a critical ratio of dispersion times; and (4) the widths of extending fingers are close to the minimum size finger that can grow at any stage of displacement. Fingering is studied in two-dimensional linear and diverging radial systems, both theoretically and experimentally. For linear systems, the length of the fingered region is proportional to mean displacement; the finger width is proportional to square root of mean displacement; and there is a small initial region void of fingers because of suppression by longitudinal dispersion. For the radial system, two limiting conditions are recognized. If the mean displacement is small compared with the wellbore radius, the length of the fingered region is proportional to the mean displacement. The width is proportional to the square root of mean displacement. If the mean displacement is large compared with wellbore radius, length of the fingered region is proportional to mean displacement, but the number of fingers approaches a constant value. Also, in the radial case there is a small initial region void of fingers because of longitudinal dispersion. INTRODUCTION The behavior of viscous fingers in miscible systems has been of interest to the oil industry for many years. Previous studies have clearly shown the existence and nature of fingers in small models.1,2,3,4 Engineering techniques for extrapolating to reservoir situations have been proposed. 5,6 Still, because of the lack of a real understanding of the mechanics of fingering, there remains uncertainty and disagreement as to the best way to scale or calculate fingering behavior in the reservoir. In this paper we discuss a study of the mechanics of fingering in miscible systems (i.e., why do fingers behave as they do?). A simplified theory is developed which we believe will (1) predict the correct functional relationship between pertinent variables, (2) permit us to calculate the order of magnitude of fingering behavior for simple systems such as linear and radial, and (3) give further insight into the problem of scaling or otherwise extending the results to more complicated reservoir conditions. The paper includes the following sections: (1) brief summary of the mixing behavior of miscible fluids in linear and radial systems; (2) four fundamental observations of fluid flow (under fingering conditions); (3) based on these four observations, a simplified theory of fingering in linear and radial systems is developed; and (4) the theoretical equations are compared with experimental fingering data measured in laboratory models. A REVIEW OF DIFFUSION AND DISPERSION As will be shown later, the behavior of viscous fingers in miscible systems is controlled in large degree by the mixing between the two fluids. A quantitative description of fingers will first require a quantitative description of mixing. Fortunately, much work has been done to clarify this subject; a fairly comprehensive review has been presented in a previous paper. 7 For present purposes let us (1) briefly summarize the quantitative description of diffusion and dispersion (both longitudinal and transverse) within a differential element; (2) present a simplification of the "width of mixed zone"; and (3) describe the effect of geometry on width of mixed zone. If one fluid is displaced from a porous medium by another miscible fluid (in the absence of fingers)

Jan 1, 1966

By E. A. Lucero, H. E. Robbins, T. H. Dudley

EL Salvador mine of Andes Copper Mining Co., E subsidiary of Anaconda Co., is in northern Chile about 18 miles north of Potrerillos, 7825 ft above sea level. Initial production is planned for the first half of 1959. Plant capacity will be 30,000 tpd, and there are 308,835,000 tons of proven ore reserves, averaging 1.49 pct Cu. The Inca adit is being driven as part of the mine-to-mill haulageway. Because of the overburden it is planned to mine the deposit by block caving. Ore will be dropped from upper gathering levels through ore passes to the Inca adit, through which it will be transported out of the mine to the primary crushing plant located a half mile from the portal.

Jan 3, 1958

By S. Le Fevre

The application of electricity to the mining and beneficiation of the magnetic iron ores of the Mineville, N. Y., district, on Lake Champlain, has resulted,in economies and enhanced quality of product, without which only a comparatively small quantity of the present output could be marketed. The output of the Witherbee, Sherman & Co. mines is about 700,000 tons per annum, and of this about four-fifths is treated by magnetic separation to increase the iron content and reduce the phosphorus. The use of electricity for the magnetic separation of the ore from the gangue is therefore of primary importance, and makes possible the application of electric power for mining and preparing the ore for concentration. The fact which speaks loudest in favor of the application of electricity is this: It is possible for about 25c. per ton of shipping ore to furnish all the power required to put the ore on cars. This includes mining a hard ore underground, from a depth of 900 ft., hoisting to surface, crushing to $ or 8 in. in size, and separating from the gangue. This also includes lights about the works, and all miscellaneous power, such as about the shops. The first plant for the generation of electric power for use at Mineville was completed in 1903, and was one of the first for the application of electricity to mining iron ore. This was a Nordberg compound condensing steam engine, direct connected to a 750-kw. alternating-current generator, 3,300 volts, 3 phase, 25 cycles. All the plants added later use the same current but with higher voltage. The map, Fig. 1, shows the power plants and the transmission system; Figs. 2 and 3 are views of the shaft houses and the mills. The power from the first plant was distributed to Mills 1 and 2, one 2,500 cu. ft. compressor, and to the Harmony hoist, which was driven by a 300-h.p. motor operating four 10-ft. drums. Our experience with the hoist covers largely the development of electric hoisting from 1903 to date, and in some cases improvements were worked out to satisfy our needs. The motor is still operating as installed, but the control apparatus has been radically changed several times. When installed, the iron re-

Jan 1, 1915

By W. B. Humes

The use of high vacuum on a large industrial scale in the ferrosilicon process for the production of magnesium marks the coming of age of an important new metallurgical technique. The economical production of reactive metals, such as magnesium, which combine with all the well-known furnace atmospheres, has until recently been successfully carried out only by electrolytic methods. It is now apparent that, through the use of high vacuum, the distillation or sublimation of many metals can be done industrially at much lower temperatures, and hence in much simpler equipment, than heretofore has been thought possible. At the beginning of the present emergency, when the ferrosilicon process of producing magnesium was brought to the fore, little was generally known about vacuum engineering, practices, and techniques. In a comparatively short time, the available equipment has been adapted, new equipment designed and built, and a fund of know-how evolved to make possible the production of thousands of pounds of magnesium per day at pressures less than 1/ r0,000 of an atmosphere. Pilot-plant operations have been consistently maintained at pressures even as low 2s one micron (0.001 mm.). These low pressures, which previously were regarded as prohibitively costly or impossible to attain, have been demonstrated as economically feasible on an industrial scale. Necessity for Vacuum The main function of vacuum in the ferrosilicon process, and hence in most vacuum smelting processes, is to lower the temperature at which the metal may be distilled or sublimed from the reduction mixture. A secondary function is to protect the distilled metal from attack by the furnace atmosphere and to permit the formation of a dense condensate. In the ferrosilicon process, magnesium is formed by the reaction between dolomite and ferrosilicon: 2(Mg0-Ca0) -\- HFeSU / t=> aMg + MFe + (CaO)2-SiO2 The metal is distilled from the pelleted charge at a free air pressure of about 0.100 mm. of mercury (100 microns). This low pressure is not needed for the reaction, but rather serves to protect the metal vapor from the oxygen or nitrogen of the atmosphere and permits the formation of a condensate free of pyrophoric material. The reaction proceeds at air pressures as high as several millimeters of mercury, and evidence has been offered to show that the actual equilibrium pressure of magnesium at operating temperatures of 2I50°F. is somewhat higher. Experimentation indicates that the yield begins to decrease at pressures above 500 microns. While no real operating data are yet available on the relationship between

Jan 1, 1944

By J. Campbell

The negative pressure developed within a solidifying sphere of pure iron is investigated theoretically assuming an elastic-plastic model. The maximum hydrostatic tension attainable is shown to be an order of magnitude smaller than that required for the homogeneous muclealion of pores in the liquid cove, and four orders of magnilude smaller than that predicted from) a rigid shell model. It is well-known that liquids can withstand large hydrostatic tensile stresses, or negative pressures. The various experimental investigations of the tensile strengths (often called the fracture pressures) of liquids are reviewed by Dean,1 and the theoretical attempts at estimating fracture pressures are critically assessed by wakeshima.2 Using Fisher's3 quation, the fracture pressure of pure liquid iron is about -70,000 atm, which may be too large by as much as a factor of 4, but is certainly correct to within an order of magnitude.' In view of the great importance of the problem of the nucleation of shrinkage cavities in castings it is of interest to determine exactly what tensile stresses can exist in the residual liquid in a solidifying casting; it has often been assumed that, because of the very low strengths of solid metals near their melting points, no interior stresses are developed at all. Nussey4 has determined theoretically the pressure in the liquid core of a solidifying metal sphere assuming that the solidified shell does not deform (i .e., is perfectly rigid), so that because of the contraction accompanying solidification (a) (about 3 pct for most metals) the progressive deposition of solid onto the inner surface of the shell causes the remaining liquid to be expanded to make up this difference in volume. This leads to a relation between the pressure P in the liquid, the initial pressure, PO, the bulk modulus of the liquid, K, and the inner and outer radii of the solid shell, o and b, respectively:

Jan 1, 1968