Search Documents

By P. K. Koh

Isothermal salt bath annealing of 0.014-in. thick 3 pct Si-Fe sheet was conducted at temperatures ranging from 927" to 1260°C in order to investigate the grain-growth behavior. Within the temperature range studied normal grain growth did not take place; instead nucleated grain growth prevailed. The nucleation frequency was found to increase with the annealing temperature, with corresponding decrease in grain diameter of ultimate secondaries after long-time annealing. Large secondaries grown by low-temperature isothermal annealing are essentially of (110)[001] orientation, and the (110)[001] texture is strong. The relatively small secondaries grown by high-temperature isothermal annealing also have orientations near (110)[001] as an average but widely scattered; thus the amount of (110)[001] texture is found to decxease with isothermal annealing temperature. Grain growth and texture development at various annealing temperatures can be described by families of sigmoidal curves with the time axis. ThE cube-on-edge (110)[001] texture and predominating large secondaries in fully annealed 3 pct Si-Fe are customarily produced by a 1100°C annealing of a primary recrystallized sheet. On annealing the primary recrystallized sheet above the temperature at which secondary recrystalliza-tion starts May and turnbull' have demonstrated that secondary grains decrease in size as the temperature is increased. The phenomenon was attributed to a decrease in the (G/N) ratio where G is the growth rate of secondary grains and N is their nucleation frequency. In addition, the growth of grains in orientations rather far from (110) [0011 occurred. The present investigation is devoted to detailed rate studies of the same phenomenon. Mi-crostructure, magnetic anisotropy, and texture data were obtained on strips of 3 pct Si-Fe isothermally annealed for various lengths of time in a BaC12 salt bath at temperatures ranging from 927' to 1260°C. The texture results are reported elsewhere.2 EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon-iron strip (3.16 pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Metallo- graphic studies indicated complete recrystallization. In order to provide a protective atmosphere and to obtain a rapid rise to an elevated temperature, a BaC12 and NaCl fused salt bath was used to heat samples isothermally at temperatures from 927" to 1260°C for various lengths of time. Torque magnetometer measurements were made on 1-in.-diam disc specimens before and after annealing, since magnetic torque curves supply information on textures and texture changes. Surface layers of the strip samples were polished and etched to reveal the grain structure. The diameters of grains were measured from micrographs at X100. The average value of diameters of matrix grains was established. Individual grains in the micrograph were cut out separately along grain boundaries. These grains were classified either as matrix grains or growth grains. The percent weight of growth grains in the cut-out patterns was reported as percent growth. Manv of the individual grains in the annealed samples were large enough to be X-rayed with a 5-mil beam for Lauegrams. Complete (110) pole figures were obtained for the primary recrystallized structure and short-time annealed structure with CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and ~ruce.~ Both the X-ray optics and the technique for pole figure differed slightly from those adapted previously.4

Jan 1, 1960

By Arnulf Muan, Klaus Schwerdtfeger, L. S. Darken

The equilibrium ratios CO/CO, of. a gas pharse coexislitrg with selected oxide phase assemblages of the system "FeO"-MnO-SiO2 and metallic iron have been determined at 1150°C. The data obtained are combined wilh the thermodynamic data on fayalite (Fe2SiOi) and "FeO"-MnO solid solutions to derive the actiuity-coiHpQsiUon relations for the various oxide components of the olivine (Fe2SiO4-,lIn2Si04) and pyroxenoid (standard free energies of formation of ferrosilile (FeSiO,), tephroite , and rhodonite from their oxides have been evaluated. In the Appendicc~s by Darken and Schivcerdtjeger the ideal solution law for solid deri oed. THE quaternary system Fe-Mn-Si-0 is of interest in many important phases of iron- and steelmaking. For instance, reduction in the blast furnace of ores containing Fe-Mn silicates, deoxidation of liquid steel with Mn-Si alloys, formation and subsequent alterations of oxide inclusions in steels, and the oxidation of manganese- and silicon-containing steels during processing are all governed largely by the thermodynamic relations existing in the system Fe-Mn-Si-O. Although the equilibria between liquid iron and Fe-Mn silicates have been studied in detail previously,' experimental data are lacking for equilibria among the solid phases. The present paper provides such data for a selected temperature, 1150°C. I) PREVIOUS WORK The general feature of subsolidus phase relations in the system iron oxide-manganese oxide-silica under strongly reducing conditions is known.' Fig. 1 represents an isothermal section at 1150°C. The phases present, in addition to silica, are three solid-solution series, viz.. the oxide solid-solution series "Fe0"-MnO (manganowiistite), the orthosilicate solid-solution series Fe2SiO4-Mn2SiO4 (olivine), and the metasilicate solid-solution series FeSi03-MnSi03 (pyroxenoid). The "FeO"-MnO solid solution is continuous between the two end members wustite and manganositeV3 as is the orthosilicate series between the two end members Fe2SiO4 and Mn2 SiO4. 4 The metasilicate solid solution, on the other hand, extends only part way from the MnSi0.l end member toward FeSiO because the latter end member is unstable relative to the phase assemblage fayalite + silica. The letters a through m in Fig. 1 identify end members of the individual solid phases dealt with [for instance, c designates fayalite (FeZSiO4) in equilibrium with wustite, e designates fayalite in equilibrium with silica, and so forth]. In addition to the phase relations there are some thermodynamic data available for the end members of the silicate solid solutions and for the "FeO" -MnO solid solution. The free energy of formation of fayalite (Fe2Si04) from its oxide components has been studied by several investigators. Unfortunately, the data obtained show considerable discrepancies. According to recent tabulations by Kelley, the change in standard free energy Affn for the reaction

Jan 1, 1967

By Henry D. Hibbard

Henry D. HibbaRd, Pittsburgh, Pa,: This is a most interesting and instructive paper, some of whose lessons should find immediate application. It points out how fuel-consumption is to be decreased in open-hearth practice, by changes in the plan of the furnace. To look first at the greatest item of loss, radiation, it is seen that thicker brick-work is advisable to lessen this. Especially is this true of the roof, made at present, almost universally, only 9 inches thick to prevent cutting. Now that high roofs, well above the course of the flame, are becoming general, and the average melter is better able to judge the temperature of his furnace, that reason has less force; and we may build roofs 18 inches thick, or perhaps better cover the usual 9 inches with an equivalent layer of sand, which has the advantage of following the arch as it rises and falls with the different degrees of heat. The side-walls of the hearth, usually 131/2 inches thick, may also he thickened up to 18 inches, and the door-linings to 7 inches; and the heat thereby saved will be valuable, while its absence from the working-platform will be much appreciated by the workmen.

Jan 1, 1892

By Sidney A. Swensrud

MUCH discussion has occurred as to the use or uses which might be made after the war of either or both .of the large diameter (24 inch and 20 inch) War Emergency pipe lines built by y the United States Government during the war, to move crude petroleum and refined products such as gasoline and light distillate fuels. Indeed, the disposition and future use of these lines constitutes, in the minds of many people, one of the most important problems of postwar readjustment in the Oil Industry. The two lines, running from points in Texas to the New York-New Jersey-Philadelphia area, were constructed only because of the inability during the war to continue normal ocean tanker movements from the Gulf Coast to the East Coast. Physically they could continue after the war to move crude or refined products, and it appears that lines of such large diameter as these, if operated at or near capacity, could move these liquids at costs per barrel which might be considered in the same general cost range as for tanker movements.1 If, therefore, we were to look forward at the end of the war to a shortage of tankers, it is probable that the continued use of these pipe lines for petroleum movements to the East Coast would be worth considering, as against building new tankers to take over the movement, provided there were no other economic or national defense reasons for restoring tanker fleets and no other better use for the pipe lines. Because of the extensive tanker construction program which has been and still is in progress, and because of our Navy's marked success in combating the submarine problem, it appears to be quite possible, however, that instead of a shortage of tankers at the end of the war, we may have a surplus instead. If this should turn out to be the case, then there would seem to be considerable doubt that these lines would continue to be used for moving petroleum or products to the East Coast at the expense of tying up tankers. It would hardly seem probable that the owner of any such tankers would ship via one of the large lines at the expense of tying up one of its own tankers, unless the pipe line tariff rate charged was lower than the out-of-pocket cost of operating a tanker as against the out-of-pocket cost of keeping it tied up. And considering that a substantial part of the cost of operating a tanker goes on even when it is tied up, it is very difficult to figure out how any pipeline tariff could be established that would be low enough to compete with individually owned tankers that otherwise would be idle. Certainly a pipe line tariff rate high enough to cover direct costs plus even a low rate of depreciation and return on the investment would be far above the out-of-pocket tanker operating costs. In view of these considerations, it has seemed desirable to examine with some care some of the various alternatives that have been suggested as to other possible uses to which these lines might be put. One of these is for transportation of natural gas to the New York-New Jersey Philadelphia area. This Eastern area, located at the destination of these lines, contains the heaviest concentration of population in the United States, and is not now served with natural gas. At the other end of the lines lie the greatest discovered natural gas reserves in the United States, if not in the world, and many

Jan 1, 1944

By Gealy W. Wallwork

INTRODUCTION The administrative processes of coal mines are becoming increasingly complex. As society evolves into a more complicated structure with greater emphasis on individuality, government regulations reach deeply into every activity in an effort to force individuals into a standardized mold. These contradictory pressures add an extra burden to the administration of a mining operation. Recent years have brought a substantial change in the skills needed by mine supervisors and managers. As a result, a better understanding of the administrative functions is necessary. The mine superintendent has the overall responsibility for the mine; for effective operation he must be sufficiently knowledgeable to oversee all the complex functions that make up the mine. This chapter does not cover all the administrative requirements because of the variation in mine operation and in company policies and organizational structure. It does attempt to identify the administrative functions that would be required at a large mine with a preparation plant. It is assumed that the mine operation is decentralized with very little duplication of functions at the organizational levels above the mine. Thus each function is assumed to be relatively complete at the mine and under the general supervision of the mine superintendent. EMPLOYMENT PROCEDURES Throughout the mining industry, in deep or surface mining, in union or nonunion companies, the success or failure of an organization is directly related to the caliber of employees who make up the organization. A company is nothing more than a group of people working together with

Jan 1, 1981

By Robert Mehl

THE precipitation of the nitride Fe4N from the solid solution of nitrogen in a Fe and of the phosphide Fe3P from the solid solution of phosphorus in a Fe both lead to the formation of structures that may be easily identified as Widmanstätten figures, within the meaning of the term as used in this series of papers. A complete solution has been obtained for the figure formed by Fe4N. The structure of Fe,P, however, is not fully known and a complete solution of this figure thus cannot be obtained; nevertheless, a study of this figure has furnished some new information. PRECIPITATION OF FE4N FROM ALPHA SOLID SOLUTION OF N IN ALPHA FE Constitution of System Iron-nitrogen A knowledge of the constitution of the whole of the Fe-N system is unnecessary for this work, though the recent studies by Eisenhut and Kaupp1 and by Lehrer2 have clarified most of the moot points; it is sufficient for our purpose to state that a Fe of high purity dissolves 0.42 per cent of nitrogen in solid solution at the eutectoid temperature, 591° C., and that this solubility decreases at first rapidly and then more slowly until at room temperature the solid solubility amounts to approximately 0.1 per cent nitrogen.3

Jan 1, 1934

By A. H. Daane, J. F. Haefling

BECAUSE of the wide use of platinum in industry and research, the physical properties of this metal, including its vapor pressure, have been studied in some detail.' The other members of the palladium-platinum group of metals have not been studied as extensively, and only qualitative information is available on the vapor pressure of palladium. Data given in literature by Vines1 and Brewer2 on the vapor pressure of palladium are based on the qualitative observations by Holborn and Austin3 and Crookes4 on the rate of volatilization of palladium filaments in various atmospheres. The general observation that palladium is the most volatile metal of the palladium-platinum metal group was corroborated by Bell, Love and Normand who studied the separation of isotopes of the platinum-group metals by a mass spectrometric method. We have measured the vapor pressure of palladium using the Knudsen effusion technique. In this work, the effusion vessel was suspended from a quartz-fiber microbalance into an induction furnace, and the amount of vapor effusing from the vessel was determined by direct weighing of the vessel during the measured heating times. This technique has been described in a report from this laboratory." The vapor pressure of palladium was calculated from these measurements using the equation P...... = 17.14 -W- (77m)'u [1] a t where ? is the weight loss in grams of vapor of molecular weight m from a vessel having an orifice of a sq cm, during t sec. The derivation of this equation from kinetic theory has been described in a previous report from this laboratory: as well as in texts discussing the kinetic theory of gases.%" Test Vessel—In the search for a suitable material for the effusion vessel, it was found that tantalum reacted with palladium metal to form intermetallic compounds, and graphite was readily dissolved in palladium metal to form what appeared to be a liquid phase at a temperature several hundred degrees below the melting point of palladium. On cooling, the graphite gathered into spherical balls in the palladium, with crystals extending radially from the center of these balls, some of which were a millimeter or more in diameter. However, palladium metal vapor did not attack the graphite vessel, so graphite could be used where it did not contact condensed palladium. Tungsten did not appear to react with palladium vapor or molten palladium at its melting point, but it was not convenient to use a tungsten-vapor pressure vessel because of the difficulty of fabricating this metal. Since the vapor-pressure range to be studied (10 2 to 10 ' mm) did not appear to extend above the melting point of palladium, a combination of tungsten and graphite served to provide a very satisfactory effusion vessel. The lower half of the graphite vessel was lined with some strips of tungsten foil and the sample of palladium consisting of a coil of sheet was placed in the tungsten liner; in this way, no contamination of the palladium by carbon occurred. Procedure After outgassing at 1500C, the tungsten-lined graphite effusion vessel was loaded with 300 mg of

Jan 1, 1959

By P. F. Gnirk, J. B. Cheatham

The results of combined analytical and experimental studies involving simulated multiple bit-tooth penetration into mck are incorporated into a drilling rate equation for roller-cone bits assuming rather idealized downhole conditions. In particular, it is assumed that the rock behaves statically in a ductile fashion during bit-tooth penetration and that the rock chips are instantaneously removed from the bottom of the drill hole. The general analysis demonstrates an application of plasticity theory for the rock/bit-tooth interaction to the formulation of an upper limit on rotary drilling rate. INTRODUCTION Extensive experimentation involving single and indexed bit-tooth penetration into rock in a confining pressure environment has demonstrated that the chip formation process is of a ductile, or pseudoplastic, nature at sufficiently low differential pressures so as to be of interest in rotary drilling. Coincident with the experimentation, analytical consideration has been given to the theoretical problems of single and indexed bit-tooth penetration into rock. In general, the analyses have assumed that the rock behaves statically in a rigid-plastic fashion and obeys the Mohr-Coulomb yield criterion. The quantitative comparison between experimental and calculated values of bit-tooth load required for chip formation has been remarkably good for a variety of rocks commonly encountered in drilling and at simulated differential pressures as low as 500 to 1,000 psi. Results obtained recently for indexed bit-tooth penetration indicate that the work (or energy) required to produce a unit volume of rock chip can be minimized by a proper combination of bit-tooth spacing and bit-tooth load for a given rock type and differential pressure. By utilizing this information, it is possible to formulate a drilling rate equation, at least in a preliminary fashion, for a roller-cone bit performing under rather idealized downhole conditions. In particular, through the use of characteristic dimensionless quantities pertinent to a roller-cone bit and to indexed bit-tooth penetration, interrelationships among bit weight, rotary speed, rotary power, bit diameter, rock strength and bit-tooth shape and spacing can be explicitly expressed. In the formulation of the equations, however, it is assumed that the rock chips are instantaneously removed from the bottom of the drill hole and- that the rock behaves in a ductile manner during bit-tooth penetration. In addition, the effects of bit-tooth load application and penetration by a yawed tooth at an oblique angle are neglected. Although the analysis is presented in the light of some rather restrictive conditions, it does demonstrate a method of applying fundamental rock/bit-tooth interaction data, obtained by combining the results of analysis and experiment to the formulation of a drilling rate equation for rotary drilling. JNDEXED BIT-TOOTH/ROCK INTERACTION PREVIOUS RESULTS The mechanics of bit-tooth/rock interaction under simulated conditions of borehole environment have been extensively described in a number of papers.l-ll In particular, the effects of differential pressure, mechanical properties of rock, pore fluid, bit-tooth shape and spacing, rate of bit-tooth load application and dynamic filtration below the bit-tooth have been investigated experimentally. From a sequence of experiments.1-4 it was demonstrated that, for dry rock at atmospheric pore pressure, the mode of chip formation exhibits a transition, with increasing confining pressure, from predominantly brittle to predominantly ductile. This transition

Jan 1, 1970

By R. C. Allen

About four years ago the writer proposed a revision of the correlation of the Huronian formations in Michigan, and noted the bearing of the question on the correlations of the Huronian rocks in Wisconsin and Minnesota.1 Dr. C. K. Leith opposed this revision and argued for the retention of the correlations of the United States Geological Survey, published in 1911,2 for which he and Dr. Van Hise were mainly responsible. As late as June, 1917, Harder and Johnson, following Leith, thought it "premature to change radically a correlation based on years of careful field work."3 The work of Wolff on the Mesabi and Cuyuna Ranges, of Hotchkiss on the Gogebic Range (unpublished), and of the writer and assistants on the Michigan ranges, together with data developed by exploratory and mining operations, has introduced so many new facts not recognized in the scheme of the U. S. Geological Survey that the correlations of 1911 must be considered, in some important respects, obsolete. Indeed, new data are accumulating so rapidly that any classification, which for the moment may seem best to explain the facts, is almost immediately modified or refined by further observations. The problem of Huronian correlations is difficult, but interesting and important. With the aid of fossils, stratigraphers of the post-Algonkian formations have been able to show that slight disconformities mag separate strata of vastly different ages, and that within physically conformable strata may be concealed a hiatus of great magnitude. In the non-fossiliferous Huronian group, minor physical breaks in the strata are only beginning to attract attention, and it is too early to discuss what bearing these will have in correlating the formations of one area with those of another, but it is safe to say that the "lost intervals" which are not disclosed by physical relationships will remain forever lost; therefore we may not hope to discover the ultimate truth concerning the

Jan 1, 1920

By Charles G. Maier

It has long been supposed that when crystalline materials are comminuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1.t The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chemical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the corrected heat of solution was less for fine material than for coarse. Continuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. Similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by Rosenhain and Stott4 and by Taylor and Quinney9 The results obtained by the different investigators were not satisfactorily consistent, but the experiments of Taylor and Quinney constitute by far the best figures obtained to date. The previous paper1 presented evidence to show that if energy is stored in the surfaces of crystals the densities of fine crystals should differ

Jan 1, 1936

By George Young

DURING the spring of 1910 I visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and, even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. The principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories.

Jan 2, 1916

By F. Peter

Technical progress takes place in two directions: the improvement of methods, affecting the quality of the product; and increase in the economy of operations, affecting its cost. In the iron-industry, practice is pretty well settled, and revolutionary changes of method are, for the present, not to be expected. Hence, in this industry, the principal endeavor is to reduce costs by the use of labor-saving inventions, such as the machines brought into use during the last decade. But it is not alone necessary to reduce the labor-cost; complete economy requires also a saving in raw material. Under this head we may rank the coal employed as metallurgical fuel; and it follows that progress includes the economic use of fuel, so managed as not to injure quality of product. In the present paper it will be shown how, by suitable utilization of the heat from the furnace, a large portion of it may be made available for other purposes. Such utilization of waste-gases is important in all industries which employ furnaces (especially heating-and smelting-furnaces); and in the first rank of these stand the iron-, glass-, and porcelain-manufactures. The following pages are devoted chiefly to the waste-gases of smelting-works, and especially to those reverberatory-furnace gases which are not combustible.' The object of metallurgical furnaces is either to fuse the material charged or to bring it to a high temperature required for further mechanical manipulation. Leaving out of consideration for the present the reverberatory fusion-furnaces, we have to do with the heating-furnaces employed in connection with rolls, hammers, or hydraulic presses. The temperature to which the material must be

Jan 1, 1914

By Gregory M. Dexter

Recent litigation in Pennsylvania between three coal-mining companies and a private water company resulted in the payment by the coal companies of the equivalent of about $500,000 to buy a new water supply to replace that which had been damaged by acid drainage from strip mining. An investigation of the relevant facts indicates that the water could have been treated by spending about $40,000 on equipment and $15,000 yearly for chemicals, labor, and power until the contarnination could be reduced about 80 pct. The water company's supply, furthermore, had deteriorated largely by reason of dry weather before stripping was begun by the coal companies. Payment to the water company should not have exceeded $300,000 and could have been as low as $100,000. Strip mining of coal is common in Pennsylvania. The most important objection to it in Pennsylvania is generally acid pollution of runoff water. An outline of the methods, therefore, that could be used to reduce such pollution, to compare acid-contaminated waters. and to treat such waters to make them satisfactory for public and industrial use is worth-while. The watershed of the West Penn Water Co. covers about 4.5 square miles, 20 miles west of Pittsburgh, and has two 90,000,000 gal reservoirs supplying about 1,300,000 gal daily for public and industrial use of which 450,000 gal daily are for two railroads. The pollution arises from weathered derivatives of typical'" Coal Measures"' rocks, the principal source being pyrite (and marcasite) in Pittsburgh and Rooster coals. Springs and seeps on hillsides issue from sandstone and limestone formations intersecting shale or clay land surfaces, or from perched water tables. The two reservoirs create an artificial permanent water table. Soap-hardness tests on three seepage samples taken in a dry summer ranged from 150 to 500 ppm. Water sampled came from aquifers above Pittsburgh and Rooster coals, obviating the possibility of contact with pyrite-containing coal. Since acid contamination of mine waters is the result of chemical reactions of oxygen and water with pyrite, it will be reduced by the exclusion of either air or water. The Sunnyhill Coal Co. has applied this principle in its "contouring" method of strip mining by burying contaminated coal-waste material under a compact, smoothed-up surface of top-soil, gravel, clay, and sand at a cost

Jan 1, 1950

By Charles Wraith

THE property of the Roan Antelope Copper Mines, Ltd., is situated at Luanshya, north-central part of Northern Rhodesia, and is connected with the main line of the Rhodesia Railways, Ltd., by a 24-mile branch line from N'dola. Most of the material and supplies that are not available in Africa are shipped into the country via Beira, on the East Coast of Africa, a distance of 1473 miles from Luanshya and the nearest ocean port. The output of copper is shipped by rail to Beira and thence by boat to the market. Passenger travel is mostly via Cape Town, a distance of 2162 miles from Luanshya. Excellent passenger trains operate on regular schedules between Cape Town and Northern Rhodesia. Luanshya is 13° south of the equator at an elevation of 4000 ft. above sea level, and has a mild healthful climate. During the rainy season, from October to March, the rainfall averages 53 in. The area is pro-fusely covered with vegetation. An ample supply of water for industrial and domestic purposes is available throughout the year. The more important supplies for smelting purposes, such as wood, coal, limestone, silica, quartzite, and clay for "dolly" mud, are con-veniently available. Excellent grades of coal, coke and firebrick are obtained from the Wankie Colliery Co., Ltd., Southern Rhodesia. The Wankie colliery has just completed the erection of equipment for the manufacture of silica brick. An ample supply of quartzite of good grade is available for this purpose. Silica brick is also obtained from the Belgian Congo and from India. Limestone is quarried from a large deposit a few miles from Bwana Mkubwa, which is 30 miles by rail from the smelter. An abundant supply of clay for "dolly" mud and for lining launders is available within a short distance of the smelter.

Jan 1, 1933

By H. R. Hanley

IT is a well-known fact that the solubility of zinc compounds decreases when these compounds are roasted in contact with iron compounds, but descriptions of tests to quantitatively express the fact have not appeared in the literature. Possibly such an expression cannot be uniformly and exactly duplicated by different operators because of the variation in the personal equation. In a general way, however, the reactions between zinc compounds and iron compounds under roasting conditions will show a certain trend with changing conditions and the approximate quantitative expression of this trend appears reasonably well established by experimental work conducted for this purpose. Ferrites and Marmatites The name "ferrite" has been given to the compound of zinc and iron which has the formula Zn0.Fe203. Among the questions pertinent to this subject are those involving inherent or natural ferrite, and also the synthetic or artificial variety. The inherent or natural product is formed when the mineral containing iron and zinc sulfides isomorphously crystallized is subjected to oxidation at roasting temperature. These isomorphously crystallized minerals are known, mineralogically, as marmatites, and contain ZnS and FeS in ratios of 2 to 1 up to 5 to 1 respectively. The zinc and iron sulfides form a definite mineral. They are firmly attached to each other and form common contact planes through which diffusion of the entities occurs during the roasting process. This diffusion of the molecularly intimate entities produces, during roasting, the compound referred to as ferrite, in proportion to the amount of iron originally present in the marmatite. For example, a marmatite from British Columbia containing 9.739 per cent. Fe and 56.87 per cent. Zn corresponds with the mineral having the formula 5ZnS.FeS. The ferrite produced in roasting, which has the formula ZnO.Fe203, contains 27.07 per cent. Zn and 46.40

Jan 1, 1929

By Edgar Kendall

A KNOWLEDGE of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of con-struction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospect-ing for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organiza-tion there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the respon-sibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment.

Jan 1, 1939

By W. B. Nelligam, J. Tittman

Refinements in radiation logging techniques during recent years have involved increasing usage of scintillation ditectors. These detectors produce voltage pulses whose heights are related to the energies of the gamma rays which initiate them. Analysis of the gamma-ray spectrum, as indicated by the pulse heights, yields information about the chemical elements composing the formations surveyed. Refined scintillation counter techniques can furnish chemical information concerning earth formations in situ, from a study of the gamma-ray spectra emitted by the formation either naturally or as a result of neutron bombardment."' Accompanying the rising interest in gamma-ray scintillation spectroscopy, there has been increased activity in the development of accelerator-type neutron sources (in contrast to encapsulated chemical-mixture sources). Such neutron generators are attractive for several reasons: (1) they greatly reduce radiation hazards to personnel; (2) there is a great reduction in contamination danger if they are lost in the hole; (3) they can produce larger neutron intensities than can conveniently available encapsulated sources; and (4) they are capable of being pulsed, thus permitting new techniques in logging. In the past, both accelerator and encapsulated neutron sources have been used by others in conjunction with scintillation-detector pulse-height analysis. The results have not been too encouraging, due to the interference among different gamma-ray spectral lines and to the fact that the gamma-ray peaks were not too clearly distinguishable above the large and ill-defined background "noise".'.' This paper is a status report on laboratory studies of a technique using a borehole accelerator as a neutron source, which gives an improved scintillation spectrum, thus permitting more accurate chemical analyses of the formations penetrated. The Schlumberger-accelerator neutron source' is presented; the origins of inelastic and of thermal-neutron, capture gamma rays are dis- cussed, and results are given for some laboratory measurements performed in borehole geometry. THE NEUTRON GENERATOR-TUBE ACCELERATOR In the attempt to develop an accelerator neutron source which would have the desirable properties outlined in the "Introduction" and which would operate satisfactorily under borehole logging conditions, a small-diameter, cylindrical, neutron generator tube has been developed. This tube utilizes the principle of accelerating deuterons (heavy hydrogen nuclei) by a high voltage so that they bombard a tritium (heavy, heavy hydrogen) target. The resulting reactions produce large numbers of neutrons of 14 Mev energy. Furthermore, the tube is permanently sealed and, thus, the use of pumping techniques in the sonde is avoided. The tube consists of a pressure control, an ion source in which the deuterons are stripped of their electrons, an accelerating gap down which the deuterons are sped by the high voltage, a secondary electron suppressor and a tritium-loaded target. Obviously, the tube requires auxiliary circuitry in a sonde for the control of the ion source, tube pressure, high voltage and other operating variables. Neutron yields, both continuous and pulsed, have been produced under simulated field conditions in the range between 1 and 10 times those conventionally used in neutron logging applications. For the experiments discussed in this paper, neutron-pulse repetition rates in the range between 500 and 5,000 pulses/sec are adequate. Furthermore, by making suitable adjustments in operating conditions, one can vary the pulse width from a minimum of several microseconds up to dc. As will be seen later, the present application to well logging does not require that one have available pulses of neutrons which are appreciably shorter than the time it takes for fast neutrons to slow down to thermal energy in water. As a consequence, much of our interest has been directed towards the operating characteristics of the tube with pulses longer than about 10 microseconds in duration. Our experience to date shows that tubes can be operated in this manner with reasonably constant, average neutron outputs.

By H. W. Clark

Electricity must be safeguarded everywhere that it is used. The conditions that exist underground make the use of safeguards more essential there than almost anywhere else. Electric Shock Electric shock is the greatest danger in connection with the use of electricity in mines, because conditions existing underground are so favorable to its occurrence. Men are often obliged to work in more or less uncertain light near bare wires that are carrying dangerous potentials. The fact that the men are standing on the earth practically connects them to one terminal of the electric generator. The moat dangerous piece of electrical equipment underground is the trolley wire. It is necessarily bare and extends for long distances throughout a mine, often less than a man's height from the track rail. Sometimes the making up of trips of cars must be done near low-hanging trolley wires. All 'bare wires offer the same danger that troIley wires do, although not to the same extent. Apparatus that has accidentally come in contact with the ungrounded side of an electric circuit is almost as dangerous as the trolley wire. A severe and even fatal shock may be obtained by coming in contact with the frame of a motor or a switch box that has become charged with electricity, or "alive," as it is usually termed. It is also possible to obtain . shocks from the frames of locomotives and cars if track sanding, poor bonding or a similar cause has put a high resistance to earth in the path of the current. Fires Caused by Electricity The danger from fires caused by electricity arises principally from defective installation and careless upkeep or from injuries to equipment resulting from falls of roof or similar causes. Fires may be started by unrelieved short cifiuits, or grounds, by the blowing of open fuses, and by the overheating of resistances. Incandescent lamps can produce heat enough to ignite combustible materials if the dissipation of the heat from

Jan 1, 1915

By A. T. Tye

REGARDING the results of preferential flotation at Cananea, Weinig has stated that "The concentrating mill of the Cananea Consolidated Copper Company at Cananea, Mexico, furnishes an excellent example of modern flotation practice. The complete figures are given because they present so forcibly the advantages of modern selective flotation."' L. O. Howard notes that "Perhaps the outstanding example so far published of improvements in results through the use of selective flotation is that at Cananea, Mexico." The following notes indicate the conditions under which the results were obtained at Cananea; also the effect of preferential flotation at the concentrator and at the smelter. In the majority of cases the full benefit of selective flotation is not fully realized, as the concentrates are shipped from the mill to smelters owned by other companies. The saving made at a certain concentrator by this method of flotation may be well understood but the saving resulting at the smelter from the results of preferential flotation at the mill is not so apparent, as the data are contained in the smelting records of some other company. Even at the smelter the great gains following preferential flotation may not be noted, as a variety of ores and concentrates from various sources are received and the difference from the changed concentrator operations of a certain mill may be obscured. As noted by Professor Weinig and Professor Howard, the results obtained at Cananea brought about a veritable metallurgical revolution at the smelter. There are probably plants at which a better preferential separation is being made than at Cananea. Many ores contain barren iron pyrite which, when depressed, does not carry copper into the tailing. Some concentrators use clean uncontaminated water for milling and in others the ore is ground much finer than at Cananea. All of these items are concerned in perfect separation. The details of preferential flotation at Cananea, therefore, are not presented on account of the perfection of the

Jan 1, 1928

By G. Sachs, E. J. Ripling, S. I. Liu, J. J. Lynch

INTRODUCTION IT is a generally recognized fact that by repeated straining the fracture stress of any metal is reduced to a fraction of its value for static loading. The value of this fatigue strength depends upon numerous factors, such as the states of strain and stress, the limits of straining, and the number of repeated loadings or cycles.1.2,3 The large volume of previous investigations on fatigue is concerned entirely with large numbers of cycles, say exceeding 10,000 and up to 500,000,000. However, the changes in fracture stress and fracture strain occurring after a small number of repeated loadings have attracted little attention. Apparently the only investigations of this type are those byLudwik4,5 who subjected steel, copper, and aluminum wire to repeated torsion. In each test the torque was varied between identical values in the two directions of twisting. Depending upon the magnitude of the moment, fracturing occurred after a number of cycles, up to 10,000. The results of Ludwik's tests will be discussed later. Such torsion does not readily yield actual stress and strain values. Therefore a preliminary study was made of the effects of repeated direct stresses, i.e., tension and compression stresses. Because such tests are considerably more tedious than torsion tests, only high stresses were used in the preliminary work, yielding definite changes in metal properties after a few cycles. It was found in these tests that strains could be controlled more readily than stresses in the investigated range of high stresses. This paper, consequently, deals with the effects of strains of equal magnitude but different signs. The metal was first prestrained in static tension by a certain amount then subjected to compression to yield the same amount of strain after unloading. This loading cycle was repeated up to a maximum of seven times. After various cycles, the stress-strain curves in tension were determined, up to fracturing. As material for these tests, the aluminum alloy 24ST was selected because it exhibits a comparatively small amount of necking in the tension test. This alloy permitted, therefore, rather accurate control at the high strains necessary to produce fatigue failures at less than seven cycles. The results of this investigation appear sufficiently interesting to extend the method of attack in various directions. It is intended to study (I) the effects of cycles up to a few thousands and (2) the effects of strains of different magnitude in tension and compression, respectively. The latter variable also includes as a special case the effects of compressive strains.

Jan 1, 1948