Search Documents

By Edwin Ludlow

THE responses to the request of the Finance Committee have been coming in with gratifying results, .but there have also been about a dozen letters received objecting in various ways to the voluntary subscription. These can be summarized as: First.-That the dues should have been increased, and thus impose the same burden on everyone. This would not have met the present situation, as under the constitution no increase could be effective until 1922. Second.-The Institute should 'live within its means, and reduce its expenses to correspond with its income. As far -as possible this was done by deferring the publication of Volume LXIV until 1921, although the papers published in that volume, were presented at the meeting in February, 1920. It is to avoid being obliged to do this again that the subscription is asked, as we feel that it is, a duty we owe to our membership_ to give them the papers presented at as early a date as possible.. Our financial situation is due to the very large increase in the cost of publication; owing to the high price of paper and printing. The cost of paper is now decreasing, and we hope that there will be' wage adjustments that will permit a lower cost for printing. Under present conditions each volume of our TRANSACTIONS costs three times as much as it did in 1917 and we would be able to publish only one' volume per year. Third.-That there are too many papers published that are 'of no interest to the writer of them .complaint.-This is undoubtedly true, but it must be remembered that the membership of the Institute includes all branches of mining and metallurgy and that all these branches are entitled to be' represented in our TRANSACTIONS by papers.

Jan 1, 1921

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By A. C. Rubel

WHAT does management expect of W and from an engineer? First and foremost, it expects that he should become, and therefore should fit himself in every way to be, a part of management so that he may assume as much and as many of the responsibilities of management as his ability and the opportunities of the job permit. Let me make clear at the start that the profession of pure, technical engineering offers but limited opportunities at the top levels because of the inherent organization of engineering work. The line of succession to top jobs may be likened to a cone with a broad base and an extremely sharp point. Consider any oil company, large or small, or any operating function of that company, and you will find few top engineering jobs in the organization. This is true by the nature of the work handled. There will be a few district engineers depending on the spread of operations, a chief petroleum and production engineer, perhaps a few research engineers, possibly some technical executive assistants, and that is usually all. The road to these jobs is a long one and the competition is tough. The larger the organization the greater the opportunity, but always the ratio of engineers to top engineering jobs is only a small one.

Jan 1, 1947

By C. C. CONCANNON

POTASH is an essential. It is necessary as an ingredient in fertilizers or as a plant food, and certainly one of the great problems, and one of increasing gravity, is the maintenance of agricultural fertility that we may have adequate food supplies. When one thinks of potash one thinks of Germany. The first and most important deposits of soluble potash salts were found in Germany, and it was through Ger- man research and the application of a highly developed knowledge of chemistry that the value of these deposits was recognized and appreciated in the field of agricultural fertilization. The Germans knew that they had something of great value in their potash resources, not only because of the advantage derived from the extensive use of it in their own intensive farming operations at home, but also because of the pressing need for it on the part of other countries. Appreciating the economic value of this in international trade, they fostered the industry to the fullest extent and devoted much attention to well organized propaganda designed to bring out the essential need for potash of German origin throughout the world. Thus every one came to believe that potash was an essential commodity of only German origin and as such it held an extraordinary position in world trade prior to 1914.

Jan 1, 1926

By AIME AIME

HOLDING the annual dinner-dance of the Institute at the Waldorf-Astoria had become such a tradition that there was widespread regret when it became known that the demolition of the building to make way for a huge office structure would perforce bring to an end the long and enjoyable series of gatherings our Institute had held there. This year the . Commodore was the place at which it was held and the commuters on the New York Central and the New Haven railroad systems, at least, found it a more convenient place for them. Except for the famous "Hoover" dinner, which will probably set a mark for all time, it was the largest dinner the Institute held, 1000 being present, and it taxed the facilities of the hotel to the utmost.

Jan 1, 1930

Discussions of the paper of Mr. Gayley read by title at the Lake Superior hieeting, but first presented at the New York meeting of the Iron and Steel Institute, October, 1904 (see p. 746). With the exception of Mr. Pourcel's discussion (p. 1038), these papers are here published under a mutual agreement between the Councils of the two Institutes, and will also be found, with others, in the Journal of the Iron and Steel In-slitute for the pear 1904, Mr. E. Windsor Richards, Past-President,' said that in 1799 Mr. Dawson, of Low Moor, read a paper before a scientific society in York pointing out the great diff'erence in the moisture of the air going into the blast-furnace in the hot months of the year and in the winter months. A cold blast-furnace was a very sensitive instrument, and showed this very clearly, for in June, July and August the furnace did not drive so well; it did not make the quality of iron and required more fuel; so that Mr. Gayley was on the right road to effect an enormous improvement in this direction. He considered that Mr. Gayley was on the way to great success, and hoped that the apparatus would not be a very expensive one. He supposed it mas too early for Mr. Gayley to let them know what the saviug was

Jan 1, 1905

By J. B. STEWART

T HE position of each hole of any series of holes was carefully located by the surveyor, plotted in plan and elevation, and numbers assigned to them. The second series was staggered halfway between the first and so on for each succeeding series. Two and a, half to three months was frequently required to grout a series of holes calculated to insure safety for sinking a distance of 10 meters or say 33 ft. Naturally the initial operation called for drilling and grouting two series of holes but thereafter each sinking campaign required only one series of holes as shown in Fig. 8. The pump handling about 75 gal. per minute corresponds to 46 tons of grout or 6 tons cement delivered as a fair over-all average for the 24 hours. Thus 600 to 800 tons of cement was used for a single section of 33 ft. depth of shaft. One campaign used nearly 1100 tons of cement. Some holes were effectually sealed with as low as 30 tons, while many required 60, and some 80 to 90 tons.

Jan 1, 1926

By David J. Raden

INTRODUCTION Economic deposits of phosphate are found at shallow depths (80 ft.) in central and northern Florida (Figure 1) where they have been mined since the late19th century(l).The present (1978) mining rate is approximately 40 million short tons per year of product (called “phosphate rock1”), which represents approximately 80% of the total U.S. production and 30% of the world production. The principal use of Florida phosphate is for the manufacture of fertilizer. There are 10 major mining companies and 20 active mines in Florida at the present time, strip mining approximately 5000 acres per year. The ore, known as "matrix," consists of gravelly clayey sands containing phosphate minerals (principally carbonate fluorapatite), quartz, and clay minerals. The clay to phosphate ratio is generally about 1:1 by weight and the sand to phosphate ratio ranges from, 1:1 to about 3:1. Mining is done by large electric draglines, which strip and cast the sandy overburden soils, generally 10 to 40 feet deep, and remove the matrix, generally 10 to 25 feet deep. Dragline bucket capacities are generally 20 to 45 cubic yards, but range up to 65 cubic yards. Mining cuts are usually 300 to 500 feet wide and up to several thousand feet long. The ore is cast into an earthen sump where high pressure water guns are used to slurrify it. Centrifugal pumps move the slurry through a pipeline to a beneficiation plant where the phosphate rock is separated from the waste sand and clays.

Jan 1, 1979

By R. A. Haney, S. J. Gigliotti

Over the past ten years, analysis of the acceptability of face ventilation systems has been based on numerical criteria rather than solely a study of air flow and methane patterns in the face area. This type of analysis has become possible primarily because of the instrumentation and mathematical models developed by the Ventilation Division, Pittsburgh Health Technology Center, Mine Safety and Health Administration (MSHA). To properly use these mathematical models, large amounts of methane and airflow data must be collected in the face area during mining activities. To supplement underground testing of face ventilation systems, a full scale model of a face area was built. This model includes a full scale model continuous miner, a face ventilation system, a gas release system, and a remote methane detection system. The remote methane detection system consists of an array of twelve methane sensors located throughout the face area. Data from the sensors are transmitted to strip chart recorders. Methane, air quantity, and other data collected during a test are entered into a computer for analysis. This paper presents the data entry system, the models used for data analysis, the test results, and the application of these results to a face ventilation system.

Jan 1, 1983

R. L. Bullock (St. Joseph Lead Co., Bonne Terre, Mo.)— The progressive approach of The International Salt Co. as described by Mr. Ryon is certainly commendable as is his paper. St. Joseph Lead Co. has been shooting AN/FO in 13/8 to 1 1/4-in. holes for several months now (as of October 1960) on a trial basis. The results thus far obtained are excellent, but conclusive evidence at this date is premature. One point that he gave should interest even the most ardent skeptic. That is, they are getting a detonation of the 1 1/4-in. ANDO charges in 2 1/4-in. holes. In light of its low sensitivity and critical diameter, this would appear to be one of the worse conditions that one could expect in which to get proper detonation of AN/FO. It has been shown* that partial confinement sometimes decreases sensitivity of a column of explosive because the air space above the explosive becomes highly compressed and in turn compresses the explosive prior to passage of the detonation front. Apparently, this does not happen in their shooting and the poor explosive coupling caused by the 2 1/4-in. holes yields a minimum of overbreak and is an ideal condition for their back.

Jan 1, 1961

By Albert S. Trube

The purpose of this paper is to clarify the definition of compressibility and to present a uniform basis upon which instantaneous compressibilities of liquids and gases can be compared. The equations gaverning the instantaneous compressibilities of imperfect gases are derived and the concept of pseudo-reduced compressibility is introduced. Part of the data presented by Brown, Katz et a1 on compressibility factors for natural gases has been rearranged. A graph of pseudo-reduced compressibility vs pseudo-reduced pressure for various pseudo-reduced temperatures is presented. The need for additional work in relating the compressibilities of liquids and gases is discussed. This information should be of value to reservoir engineers in making non-steady state performance calculations in gas reservoirs. It should be of further use irz pointing the direction for additional research in the nature of liquid and gas compressibilities. INTRODUCTION With the increasing use of steady and non-steady state well and reservoir data, there is a corresponding increase in the importance of the various factors entering into such calculations. Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of the reservoir fluids well in advance of the more accurate laboratory data. One such factor is the isothermal coefficient of expansion of the media which are transmitting and attenuating the non-steady state pressure waves. The average isothermal coefficient of expansion, or "compressibility" is a complex function controlled by the physical properties of the formation and the fluids contained therein. The isothermal expansion coefficients for reservoir gases are usually quite variable, in many cases being highly-pressure sensitive. The coefficients for reservoir liquids tend to be pressure sensitive, but not nearly so much as reservoir gases. The coefficients for solids, usually expressed in terms of a "modulus of elasticity" are relatively insensitive to pressure variations within their elastic limits. For this reason, and also because many previous applications have been limited to rel- atively small pressure ranges, there has been a tendency to ignore the variable nature of isothermal expansion coefficients and treat them as constants. Also, the term "compressibility" by which these coefficients are generally designated is commonly confused with a similar term, z, used to define the deviation of an imperfect natural gas from the perfect gas laws. A clear distinction should be made at the outset between the term "compressibility", which is an isothermal coefficient of expansion of a substance, and the term "compressibility factor", z, which refers to the deviation of a gas from the perfect gas laws. Although the scope of this paper is limited to the compressibility of single phase natural gases, it is definitely related to the problem of accurately estimating the compressibilities of single phase hydrocarbon reservoir liquids, which will form the basis of a future presentation. BASIC PRINCIPLES The coefficient of isothermal compressibility of a substance, c, is usually determined from pressure-volume or pressure-length -measurements depending upon whether the substance is single phase gas, liquid, or solid. A convenient method for making such estimates for a finite change in pressure and volume at constant temperature is to use the well known equation V1-V2/V1 (p2 - p1) .....(1) Eq. 1 is negative because the volume of a confined substance decreases as the pressure is increased. In this case V1 > V2 and p2 > p1. This equation is useful in approximating the compressibilities of single phase gases and liquids undergoing small pressure changes. It is evident, however, that this equation is almost identical with the determination of Young's modulus of elasticity for solids. If the assumption is made that change in length is directly proportional to change in volume, as would very nearly be the case for a steel rod in tension within its elastic limit, then E5=-L1 (p2 - p1)/L1 - L2 .......(2) in which E. is the isothermal expansion coefficient, or Young's modulus of elasticity, for a solid. And further, for this special case L1 (p2 - p1)/L1 - L2 .......(3)

Jan 1, 1958

By J. Gross

G. H. Clevenger, Chairman of the Milling Methods Committee of the Institute, made the following introductory remarks: "Several years ago, a number of us felt that the time was ripe for a fundamental investigation of crushing and grinding. At the outset, it appeared that the first thing we needed was a yardstick whereby grinding efficiency could be measured. "The U. S. Bureau of Mines has been most generous in cooperating with the Milling Methods Committee in getting this work well under way. John Gross, who served the committee for a year as secretary, was placed in charge of the investigation and has been ably assisted by S. R. Zimmerley. "Messrs. Gross and Zimmerley will now present the Progress Report covering their work to date." PROGRESS REPORT J. Gross, Salt Lake City, Utah. -This has not been a simple problem, and when I tell you that we can give you a verbal report of what we have done during three years in five or ten minutes you will realize that we have necessarily done a great deal of work that does not appear in the final results. We have been in a virtually new field. Therefore, we have had to feel our way at each step so as to be fairly sure we were correct. The first thing that was realized in this problem was that unless we had some method of measuring what happened when we crushed an ore, we might as well quit and not go further. We realized that if we tried to measure the results of crushing or grinding by the ordinary sizing test we would not get anywhere. We could sieve down to say 200 mesh fairly accurately; we could even go one sieve size further with a little less accuracy, and then we were absolutely lost, unless we went into microscopic measurement. Even this latter method would not have been satisfactory. The question was: what were we going to measure? If we were going to measure size, we might measure one particular dimension of a particle and be off 200 per cent. or more. If we tried to measure surface, we would have something tangible; the surface of a particle, no matter how irregular, is something definite, far more definite than any linear dimension would be. Moreover, if we could measure surface, we would immediately have a method of checking the Rittinger law as to whether it was or was not correct. So the first thing that we sought was a method whereby we could measure surface on crushed particles or, we will say, on particles; it would not make any difference whether crushed or not. It then became a question of what kind of particles we were going to use in obtaining a method for surface measurement. We realized that it would be rather a com-

Jan 1, 1928

By AIME AIME

THE growth of the spirit of progress and mutual aid which motivated the founders of the Institute sixty years ago in Wilkes-Barre was vigorously demonstrated at the sixtieth anniversary meeting held there on May 22. Committees headed by Cadwallader Evans, "resident director" of the Institute, and Paul Sterling, chairman of the local section, had arranged for a full-day tour of the northern anthracite field, so that the hundred and fifty members and guests who had come for the celebration of the anniversary might see the changes and progress made in that field in recent years. More than forty automobiles were in line in the cavalcade which left the Westmoreland Club at nine- thirty. Operations visited were fully described in the May issue of MINING AND METALLURGY, so it is enough to say that after a seventy-five mile drive through the beautiful Susquehanna Valley and over the rolling green hills of northern Pennsylvania a stop was made for lunch at Forest City. Carey, Baxter and Kennedy, contractors at the stripping operations there, had provided, in the shelter of tents, a well-prepared luncheon and other refreshments. The return trip was made by way of Scranton, arriving at Wilkes-Barre at five- thirty.

Jan 1, 1931

By J. S. Marsh, T. B. Winkler

THE past year, the first full one of peacetime production, proved that the process of beating swords into plowshares has increased in complexity in step with civilization. Further, judging by various remarks of our distaff departments, the crystal balls of certain radio and magazine oracles must have been cloudy, because we have been in formed from time to time that coveted items such as automobiles and refrigerators did not appear in great abundance. This seemingly extraneous matter is really not out of place here, however; the steel producer and the fabricator exist in a sort of symbiosis: the making of consumer goods produces scrap which is returned to the steelmaker who makes more steel, and so on and so forth. Thus, no abundance of automobiles, no abundance of scrap from this normal source; and other sources had been picked pretty clean during the war. To be short, so was scrap. Since the economy of the steel industry lean; as heavily upon iron from scrap as upon iron from ore, the statement on transformation of swords to plowshares follows. But this is not the whole story: after all, ingot production was a record for a peace year!

Jan 1, 1947

By W. E. STOKES

SOME extension of flying service to the mining industry occurred in 1938, particularly in Canada, where freighting activity radiated from Edmonton into the new northern mining districts. Again the airplane demonstrated its usefulness in getting new equipment rapidly into the field and in decreasing shutdown time while waiting for repairs. An 18-ton Caterpillar tractor with shovel attachment was disassembled, brought in by plane, and placed in operation at Berens River, Ont., within seven days after its de- livery at Winnipeg. At Central Patricia a mill breakdown required the replacement of a full mill head and trunnion with ball bearings, weighing 2700 lb. The Canadian Airways Junkers, termed the "flying boxcar," was called in from Yellowknife, 1300 mi. away, and the new installation was completed three days later.

Jan 1, 1939

By Ralph M. Roosevelt

IN AS MUCH as our Institute, by tradition, never adopts any official view of matters upon which difference of opinion exists, it may be taken for granted that the duty of its Production Control Committee does' not embrace the formulation of any general policy on that much-discussed subject. During the first years of its existence the Committee confined its activities to making arrangements for an annual general session at which the broader aspects of the general problem were discussed by men both within and outside the mineral industry. These general sessions, although interesting, did not indicate any definite path of progress, so during the last year the Committee has held a number of luncheon meetings at which the members might discuss in detail problems existing in the specific industries with which they are most closely acquainted, in the hope that discussions dealing with conditions rather than theories might result in the bringing to light of some general truths. Most of these truths have been fairly obvious from the beginning but they are of such basic importance that a periodic restatement of them seems worth while,

Jan 1, 1932

THE committee in charge of arrangements for the meeting of the Institute in September has com-pleted its program. The headquarters of the meeting will be at the Palace Hotel, San Francisco, and the registration committee will be at the hotel all day on Sunday, Sept. 24, and from 8 a.m. until noon on Monday. On Sunday afternoon, automobiles will be available for sightseeing trips around the city. Monday will be devoted to technical sessions. In the morning, there will be sessions on Mining and on Iron and Steel; in the afternoon, sessions on Mining and Milling. At these sessions, in addition to the papers mentioned in the tentative list printed in August, there will be presented three papers on the geology, mining and milling of the Comstock lode; one on the Aztec mine, Baldy, N. M.; one on the Colombian oil fields; and one on charcoal precipitation of cyanide solutions. The luncheon on that day will be Dutch Treat, for men only, at the Engineers Club. On Monday evening, there will be an informal buffet supper at the home of F. W. Bradley. On Tuesday morning, a party of 50 men will leave for Hetch Hetchy. During the four days of the trip, the party will see the Priest tunnel and earth dam under construction by steam-shovel and hydraulic-fill methods, the Big Creek shaft and tunnel, early intake power plant and tunnels and the Hetch Hetchy dam under construction. For those who remain in San Francisco, Tuesday will be "San Francisco Day." There will be motor trips to the Presidio, Cliff House, Golden Gate Park, and other points of interest, and shopping trips to Chinatown. On Wednesday, "University of California Day," the party will be guided through the university by members of the Mining Association, the affiliated stu-dent society, and will see the Greak Theatre and not-able buildings. Thursday will be "Leland Standford, Jr. University Day." Automobiles will leave the Palace Hotel at 10 a.m., and will return from the university at 4.30 p.m. Friday has been reserved for trips to the Selby Smelter, to Mt. Tamalpais, or to other points of interest. Arrangements will be made to visit the mines or gold dredges in California, if members desire to do so, but such trips must of necessity be considered special trips and arrangements will have to be made to suit the convenience of the individual or party. The Golf Committee will make arrangements for those who wish to play golf.

Jan 9, 1922

By Lucien Eaton

THE accuracy with which detachable bits can be sharpened and gauged by grinding has made possible refinements in design that cannot be attained by forging. This applies particularly to gauging, where accuracy is of the greatest importance. Gauge changes of 1/32 in., and even 1/64 in., are now feasible, whereas 1/16 -in. changes are about the limit in accuracy for forged bits. These small changes in gauge are feasible, however, only with certain fundamental principles of design. Within reasonable limits the depth to which a hole can be drilled is dependent primarily upon the loss in gauge, or diameter, of the bit. In drilling there is always a certain amount of "overdrilling"-the bouncing of the bit in the hole and its rotation wear away the walls-so that the actual diameter of the hole is greater than the diameter of the bit. The amount of this overdrilling depends upon the kind of rock being drilled, and is sometimes sufficient to permit the use of the same diameter of bit for the full depth of the hole. If, for instance, a 1 3/4-in. diameter bit overdrills 1/32 in. in diameter, and loses 1/64 in. in gauge in drilling 2 ft. of hole, the bottom of the hole is still 1/64 in, larger than the original diameter of the bit, and a new 1 ¾ -in. bit can be used to drill the next 2 ft. If, however, the overdrill is less than the loss in gauge, the next bit must be of smaller diameter. The first requisite in reducing loss of gauge in drilling is to have the points and corners of the wings of the bit cut circles of the same diameter, thus producing a reaming surface with continuous bearing on the wall of the hole. The greater the reaming surface, the less the gauge loss that is to be expected. If the reaming surface, however, is too large, it may impede the rotation of the bit through excessive friction. This principle was probably first recognized in the design of the Carr bit (Fig. 1), a bit with a single cutting edge of wide angle, a definite reaming edge, and a large center hole. The same idea was followed in designing the double-taper cross bits, which are now standard almost everywhere.

Jan 1, 1939

H. G. Haemers (Ghent University, Belgium)—The authors claimed "the results of their work indicate that the metals can be arranged in a sulfation series similar in its application for selective sulfation tot the electromotive series for displacement of metals from solution". The series as stated in decreasing order for tendency of SO3 give up, is the same as that stated by free energy diagrams. Indeed, the degree of stability of a sulfate is measured by the free energy of sulfate formation out of the corresponding metal oxide and SO3. The more negative the value of the free energy (-DG) the greater the stability of the sulfate. As a second consequence this statement results in a relative aptitude for capture of SO3 by each metal oxide when brought in contact with the sulfate of other metals. Let M1 and M1 be the two metals, and — DG1 and — DG2 their free energy values at temperature T. Both sulfates are stable at temperature T if - DG1 < O and — DG2 < O. In case where — DG1 < — DG2 the stability of M1SO4 is greater than that of M2SO4, and when M1O (oxide of

Jan 1, 1958