Search Documents

By CHARLES SIMENSTAD

COAL preparation, or coal washing, is not a new subject to the Pacific Northwest. Most of the coals mined in this state smaller than lump, and nearly all such sizes mined on the Pacific slope of the Cascade mountains, require washing before marketing. A large proportion is being put through some washing process, but coal washing in this state, has not reached the efficiency it is practicable to obtain. In fields where the coal, as mined, contains less impurities, where working conditions make it practicable to eliminate some of these impurities under- ground, or where a large proportion of the run-of-mine coal is lump, coal preparation does not present the problem it does in our local field. Here the coal is associated with considerable impurities and the slack, or steam sizes, aggregate about 80 per cent. of the output. Therefore, approximately 80 per cent. of the coal mined must be washed to become a valuable fuel. Washing then becomes a major operation, as hand picking of the 20 per cent. of lump is a standard and comparatively simple operation. Some coal beds here are so interstratified with bone, of a more or less massive nature, that hand picking of lump is not economically efficient. In such cases the coal must be crushed fine enough for it to be freed from the bone, so that the two may be separated. Coal cleaning in this field, therefore, must receive skilled attention to purify this fuel and raise its stand- ard. Without greater efficiency in cleaning, the importation of coal from outside the state will be even greater than in the past.

Jan 1, 1926

By H. Wilhelm, E. L. Davis, W. A. Clark

MATHEMATICAL formulas for the analysis of the behavior of producing oil wells can be devised which will be correct for the assumed conditions. However, in an oil zone, variables always exist which are unknown, or to which. it is impractical to assign mathematical values. It seems apparent that one should reason back from observed facts to an analysis of causes, rather than start with a hypothetical reservoir with assumed properties and attempt to explain observed phenomena. In this paper we hope to throw some additional light on factors influencing production, especially edgewater behavior. OIL and gas are contained in reservoirs of either the sealed type or the edgewater type. In the former all the recoverable oil is produced by gas expansion only. In this type of reservoir, edgewater is not effective. This may be because of faulting or overlapping strata, or more often, probably, the edgewater pressure is ineffec¬tive on account of resistance or lack of head.

Jan 1, 1933

By S. G., Lasky

IT seems to be in the nature of concepts that they have many meanings, and that the meaning best reflecting the primary interests of a person tends to be accepted by him as the normal meaning of the concept. The concept of ore reserves is no exception, for there is no unanimity of meaning among the several groups of us who are interested in ore reserves, nor even among the individuals of a single group. The groups most interested in ore reserves would seem to include at least the mining industry, perhaps State taxing agencies, and the Federal Government in all its diversified activities, and I would include also the citizenry at large or at least that part of it that consciously thinks about problems-of national welfare. To each of these, and to different individuals within them, the term reserves represents something different, and the farther away the individual or group gets from physical contact with the ore, the more abstract does his or its concept become. It is something different to the policy maker from what it is to the fact-finder or to the miner.

Jan 1, 1945

H. Van F. Furman, Denver, Colo. (communication to the Secretary): There are some statements in Dr. Carpenter's interesting paper which appear to require explanation, if not modification.

Jan 1, 1901

By Eugene Guccione

Australia could eventually become a major world supplier of uranium oxide-but how quickly that happens depends on the outcome of a highly complex and emotional battle among different special interests.

Jan 1, 1977

By K. Tanaka, J. D. Mote, J. E. Dorn

It) an attempt to ulLcoce.lP the operative strain-rate-contl-olliy: dislocation nieclzanistns, specially oviented sizgle clystals of the intel-nzediate 1zexagonal phase containing Ag plus 33 at. pct A1 were tested in tension over a wide range of temperatures. Slip was observed to take place by the {0001} <1120> {l100} mechani fracture took place across the(i100) plane and winning occurred by the (i01Z) ?lechanisn. Basal slip exhibited a strong yield point over the -alzge from 77 to 450°K, the upper ,esolved shear st]-ess having the exceptionally high value of 10,500 psi over this entire ?-a?zge of tenzpei,atuves. The critical 9-esolved shear stress for prismatic slip decreased f7-om 48,000 psi at 4.3"K to 23,000 psi at 170°K (Region 1) follozcirg zt:lzich it decl>eased sloz&ly to 21,500 psi at 475°K (Res&apos;on II); from 475" to 575°K (Regioz III), the c7-itical esolced shear stress dec&apos;-eased precipitously to 2000 psi; and from 575" to 750°K (Region IV) it decreased less afi&apos;dly to a low value of about 500 psi. Pvistintic slip in Region I was pobably controlled by the tliel-nally activated riecharzisui of nucleation and g,-ozcth of kinks in dislocations lying in Peierls potential troughs. In Region II for prismatic slip the critical 1-esolved shear stress was slzocn to be deteemined by sh0l.t-range 01-dering, Overall the forgiorz fo basal slip, 7.c.lre1-e a Strong yield-point phenorlienu ia7as observed, the critical vesolved slzea?-stress was shoztn to be determined by n conibirzation 0-f Szizuki locking and short-range-order Izavderzizg, The precipitous decrease in the critical resolved shear stress with increase in ter,/pe7-atrir-e over Region HI was tentatively ascribed to a decrease in the degree of slort-)ange 07-del;iqq (0)- clusteing) and also the effect of fluctuations the degree of o?der, It is at pgreser2t zrtzce)taitz as to 1t1hethe1- these or other possi1)le effects are also ,esponsible. fo- the data obsel-ved 172 Region IV. 1NTEREST in inter metallic compounds stems not only from their role in dispersion hardening of polyphase alloy ystems but equally from their potentialities for high strength, hardness, and stability not only at atmospheric temperatures but especially at elevated temperatures. As summarized in a re- cent symposium of the Electrochemical Society on "Mechanical Properties of Inter metallic Compound", most of the experimental evidence regarding the mechanical behavior of intermetallic compounds centers about the effect of temperature on the hardness and ductility of polycrystalline specimens. The available data reveal that the plastic behavior of intermetallic compounds might be rationalized in terms of the usual dislocation mechanisms appropriate to a solid solutions providing the additional complexities arising from crystal structure, long-range ordering, short-range ordering, and defect lattices are taken into consideration. It is apparent, however, in terms of the history on a solid solutions, that a complete detailed mechanistic rationalization of dislocation processes may not be possible until the deformation processes are studied in single crystals of intermetallic compounds. The present paper contains a preliminary report on the plastic behavior of single crystals of the hexagonal Ag-A1 intermetallic phase over a wide range of temperatures. The results confirm the thesis that single crystal data provide a most effective method of identifying operative dislocation mechanisms in intermetallic compounds. EXPERIMENTAL TECHNIQUES Several factors prompted the selection of the hexagonal Ag-A1 intermetallic phase for this preliminar investigation on the plastic properties of single crystals of intermetallic compounds: 1) This phase has a wide solubility range5 which would permit future investigations on the effect of composition and axial ratios on slip mechanisms. 2) Although it undoubtedly exhibits short-range ordering (or clustering) this intermetallic phase is free from complexities arising from long-range ordering.6 3) Since the atomic radii of aluminum and silver are practically identical, the possible complications due to Cottrell locking are minimized. 4)Whereas the dislocations on the basal planes are expected to dissociate into Shockley partials and are thus susceptible to Suzuki locking, those on the prismatic planes probably remain complete. 5) The axial ratio, being 1.61, is almost ideal, suggesting that short-range ordering may be almost spherically symmetrical. The present investigation was conducted exclusively with the hexagonal Ag-A1 alloy containing 33 at. pct Al. Preliminary investigations revealed that this alloy undergoes basal slip by the (0001)

Jan 1, 1962

By A. W. WALKER

All branches of production engineering showed steady and definite progress during 1941. Most of it has been of the slower and more conservative type rather than the sensational. To a large degree the changes have been influenced by the expanding war economy, and this tendency will probably be even more marked during the coming year. The stress of the times is placing more emphasis on the principles of engineering and conservation, with the object of obtaining the greatest possible recovery with a minimum waste or expenditure of equipment. Also available material supplies are often being turned to new uses.

Jan 1, 1942

By Clyde E. Williams

MUCH has been said recently concerning the depletion of the Lake Superior iron ore re- serves. Estimates given indicate a total life of the present known reserves of twenty to thirty years. Some argue that there is no need to concern ourselves about the possible depletion of the Lake Superior iron ore supply because foreign ores can be brought in to this country at a lower price than rich agglomerated ore can be produced from the lean domestic ores. Some fear, as a result of this, a displacement of the steel business from present districts to the Atlantic seaboard. Others show that foreign ores will be brought to interior points via the projected Great Lakes-St. Lawrence waterway. Others believe that the South, given better freight rates, will extend its iron and steel market into northern territory.

Jan 1, 1931

By M. R. Geer, H. F. Yancey

Coal washing assumed an important role in the mining industry of the Pacific Northwest long before washing practice became firmly established in the Appalachian field. A Scaife washer was operated in the state of Washington in 1887; and by 1927, the fist year for which complete statistics were compiled, nearly a third of the state&apos;s coal production was washed, in comparison with only about 5 pct for the country as a whole. Mechanical preparation was adopted in Alaska in 1922 in a plant constructed by the United States Navy at Chickaloon to provide bunker coal for naval forces operating in northern waters. Many of the coal beds mined in Washington and Alaska contained more impurities than those mined elsewhere, and this circumstance contributed to the early interest in mechanical cleaning. A much more important factor, however, was the inclination of the coal beds. With steeply pitching beds, hand sorting by the miner at the face is impossible; consequently, all material must be loaded and dealt with on the surface, just as is now proving the case with mechanical mining of flat beds. Thus "full-seam" mining afforded the same stimulus to the early development of coal washing in the Northwest that it is providing under mechanization in the rest of the country today. Objeet and Scope &apos; This report is intended to provide a general summary of the status of coal-washing practice in Washington, Oregon, and Alaska—an area in which some of the coals mined are more difficult to wash than those mined elsewhere in the country. Detailed flowsheets of plants, statistical data on production, and cost figures have been omitted, largely for the sake of brevity but also because such information is principally of only local interest. On the other hand, considerable washability data have been included because they are Washington At present Washington leads all other states in the percentage of its total production that is cleaned mechanically, 82.1 pct in comparison with the national average of 25.6 pct in 1945.&apos; The washing problems encountered in this state are highly variable because the mountain-building forces that created the Cascade Range caused such intense folding and faulting of the beds in some fields that the rank of the coal was increased to anthracitic, while in other fields more distant from the mountains the beds were relatively undisturbed, and the rank of the coal ranges down through subbituminous to lignitic. The complicated and burdensome schedule of sizes prepared in most coal fields has never been required by the Washington market. With but few exceptions, lump is prepared on a round-hole screen of about 3 in. size, egg is about 3 to 1 5/8 or 1½ in., and nut is 1 5/8 or 1½ in. to either 1 or ¾ in. Some mines screen no finer than ¾ in. and market a slack coal of that top size, but generally the coal is screened at about ¼ in. to give a stoker coal of ¾ or 1 to ¼ in., and a ¼ in. to 0 "buckwheat." During recent years the market for lump coal has largely disappeared, and lump is crushed to supplement the pro-

Jan 1, 1950

T. Kirke Rose, London, Eng. (communication to the Secretary*) :—The authors have shown that, under certain conditions, the rate of dissolution of gold by chlorine and bromine is reduced by the addition of 10 per cent. of silver to the gold, and that the action is almost stopped when the silver amounts to 30 or 40 per cent. of the alloy. Even if full recognition is given to the practical way in which the work was done, however, it is to be regretted that Prof. Hofman and Mr. Magnusou did not determine the temperature at which the experiments were carried out. From the details given, it may be inferred that the temperature was raised by chemical action by about 20&apos; C. when 21 g. of sulphuric acid was added, and that the mixture was then slowly cooled down during the experiment. When bromine or very weak chlorine solutions were used, there could not have been any perceptible heating-action. As the action of both chlorine and bromine is aided by heat, it follows that the stronger solutions of chlorine were given an unfair advantage over the weaker solutions, and over bromine. If the temperature had been the same in each case, I do not think that the conclusions deduced by Prof. Hofman and Mr. Magnuson&apos; would have been found to be justified. (This is speaking generally. In barrel-treatment the conditions are similar to those in the experiments.) The superior speed of bromine as compared with chlorine at equivalent strengths is not yet disproved, and the differences noted between strong and weak solutions of chlorine may have been largely a function of the temperature. Moreover, the authors used somewhat-coarse particles of gold, and did not try how far time was a factor, although it is obvi-

Jan 1, 1906

By Zay Jeffries

HOSTILITIES in Europe, Asia, and northern Africa were responsible for dislocations in rare-metal supplies during 1940. Although the consumption of some of the rare metals is small the dislocations may be relatively large. In some cases these are advantageous to North America and in others they are disadvantageous. Specific instances will be cited later. Barium T HIN films of barium metal on special steel balls greatly improve the life and reduce the friction of rotating anodes in highly evacuated small X-ray tubes and make possible the operation of these anodes at relatively high temperatures. These remarkable results are described in an article by Atlee, Wilson, and Filmer in the Journal of Applied Physics for September, 1940. Oil could not be used because of the high temperatures on the one hand and its volatility on the other. Fig. 3 shows diagramatically the rotating anode and the method of coating the steel balls with barium. The letters K.I.C. refer to "Kemet Iron Clad." The K.I.C. wire was mounted so that the barium could be evaporated by direct passage of the electric current. At high temperatures the barium dif-

Jan 1, 1941

By Charles H. Moore

In the study of the properties of rutile pigments it became apparent several years ago that certain physical and optical properties could not be determined on particles of pigmentary size. Since reflected light is the dominant type which reaches the eye from small particles, the true color of pure rutile was not known. Most rutile pigments are acicular in habit, elongated parallel to the "c" axis. It was considered important to know the nature and tone of light transmitted, for example, by a basal plate. Further, as shown by spectrophotometric curves, there is a very strong absorption of light of 4000 k as measured on particles with random orientation. It would be interesting to see whether this absorption position varied with predetermined and selected orientations. Also, since the behavior of titanium pigments in a vehicle is important, a knowledge of the surface wettability of single crystals by various media should prove very fruitful. Finally, the optical properties of rutile are such that it should show, in a single pure crystal, greater fire and brilliance than the diamond. Mineralogists had long speculated that this would be the case and curiosity was strong to produce a single crystal large enough to cut.

Jan 1, 1949

By T. T. Read

TWO papers on health and safety were given Thursday afternoon when a joint session of the Health and Safety Committee and the Mining Methods Committee was held. T. T. Read presided and the first paper, on ventilation at Climax, was presented by the author, L. H. Glanville. In the subsequent discussion by Cloyd M. Smith, P. B. Bucky, B. F. Tillson, D. F. Haley, J. L. G. Weysser, and others a number of interesting points not covered by the paper, which appears in full in the January Mining Technology, were brought out. Ventilation troubles in mines so often hinge on the air being too hot and damp that it was interesting to hear of one where it is frequently too cold and too dry.

Jan 1, 1943

By Sherwin F. Kelly

LITERALLY from the four corners of the earth, from Jerusalem and China, from Mysore and Uganda, as well as from geophysicists in the United States, came contributions from workers in magnetic and electrical geo-physical methods, most of them unfortunately unable to be present themselves. The most lively discussion centered on the phenomena of natural potentials in the earth, dealt with in M. B. R. Rao&apos;s paper from Mysore, and in Parke Dickey&apos;s contribution, which he presented in person. In the oil fields, the weak potentials observed in sedimentary strata traversed by bore holes have traditionally been ascribed to phenomena of electro-filtration and electro-capillarity. Research tending to refute this theory was presented by Dickey, who reported the existence of natural potentials in core samples, and between strata exposed in underground workings. This precipitated a lively discussion as to the possible role of electro-filtration, selective adsorption of ions by mineral particles, and electrolytic potentials, in the production of this phenomenon.

Jan 1, 1943

By Harry H. Power

INDUSTRY has the right to expect the petroleum engineering schools to supply more than the minimum technical qualifications necessary to obtain or discharge the responsibilities of a particular job. The basic training, social and economic orientation, should go far beyond these minimum requirements. Petroleum engineering students should also be well grounded in the history of the oil business so that they may understand the industry&apos;s progress since the advent of the Drake well. Furthermore, according to P. H. Bohart, the schools "have a definite duty to help the students form a workable philosophy of life, which includes an appreciation of the service of science to mankind, and a belief in the obligation of the individual who enters a profession to exalt himself by continuing his studies and growth so that he may never cease making contributions to the advancement of science and industry."

Jan 1, 1948

By F. Julius Fohs

CENTRALLY located with relation to the largest iron- and steel-producing districts of the United States, the fluorspar-deposits of Kentucky possess increasing interest and importance. As typical of the numerous fluorspar-mines of Kentucky and Illinois, I have selected for description the Memphis., because it and others of its immediate group exhibit the conditions characteristic of all. I. THE MEMPHIS MINE. This mine lies 5 miles NW. of Marion, in Crittenden county, Kentucky, a station on the Chicago and Nashville division of the Illinois Central R. R. For the first mile and a half out of Marion we see only Birdsville or Middle Chester sandstones of Mississippian age. Then we cross a fault of some 350 ft. displacement, and the Ste. Genevieve oolite sets in. Beyond the fault, oolite is the predominant rock, except that the bills to the north have a capping of Cypress or lowest Chester sandstone, 80 ft. below which is an outcrop of from 6 to 10 ft. of Ste. Genevieve (Rosiclare) sandstone. Occasional sink-holes are noticed, and as the mines are approached evidence of faulting is again seen.. A line of crude head-frames and open-cut dumps, extending for more than a quarter of a mile, marks the Klondike vein. The open-cuts are from 15 to 20 ft. deep, and in most of them, from the surface down, was found the reddish gravel which is really fluorspar-some of it white or purple and crystal-clear (if the red clay is washed off), and some carrying iron and silica, and stained by waters from the decaying limestone walls. In one of these cuts, at a depth of 20 ft., white and purplish honey-combed fluorspar was found, in which the larger cavities are due to limestone and calcite leaching, and the minute ones to the leaching of zinc-blende.

Apr 1, 1909

By J. P. BONARDI, William F. Boericke

BOULDER COUNTY, Colorado, ranked during the war years and until the end of 1918 as one of the foremost tungsten-producing districts of the world. In 1919 production fell off drastically, due to heavy importations of foreign ores from China, Burma and South America. So large were the imports that even after the enactment of a protective tariff in 1922 of 45c. per lb. on tungsten metal, equivalent to $7.14 per unit (201b.) of tungstic acid? (WO,), the stocks of metal in this country were extensive enough to supply the demands of industry, and prevent general resumption of mining by domestic producers. Even today there are only two producers in the Boulder district though at one time as many as twenty separate companies were in operation. About the same ratio holds for other tungsten-producing districts in the country, including California and Nevada. Total consumption of tungsten concentrate in terms of 60 per cent WO2 in the United States amounted to approximately 3790 tons in 1928, according to Frank L. Hess.&apos; Of this amount, domestic mines contributed 1290 tons, and the rest, 2500 tons, was imported. Yet in 1917, with tungsten concentrate selling at $20 per unit, the Boulder district alone produced 2707 tons, indicating the effect of enhanced ore price upon production. It is believed by American tungsten miners that, given a sufficiently high tariff, all the demands of industry can be met by domestic production without placing a prohibitive burden on consumers. For instance, in steel manufacturing the percentage of tungsten entering into the manufacture is so small that, ?regardless of cost, it can constitute but a small fraction of the cost of steel to the buyer.

Jan 1, 1929

By Arno C. Fieldner

METALLURGICAL coke and the by-products of the carbonization of coal continue in strong demand. Nearly 500 new by-product ovens were constructed in 1943. Output of by-product coke in the first ten months of the year was about 2 1/2 percent higher than in the corresponding period of 1942, but beehive production remained on approximately the same level as last year and constituted about 11 per cent of the total coke output.

Jan 1, 1944

By F. C. Bond

SIZE of grinding media is one of the principal factors affecting efficiency and capacity of tumbling-type grinding mills. It is best determined for any particular installation by lengthy plant tests with carefully kept records. However, a method of calculating the proper sizes, based on correct theoretical principles and tested by experience, can be very helpful, both for new installations and for guiding existing operations. As a general principle, the proper size of the make-up grinding balls added to an operating mill is the size that will just break the largest feed particles. If the balls are too large the number of breaking contacts will be reduced and grinding capacity will suffer. Moreover, the amount of extreme fines produced by each contact will be increased, and size distribution of the ground product may be adversely affected. If the balls added are too small, grinding efficiency is decreased by wasted contacts that are too weak to break the particles nipped; these largest particles are gradually worn down in the mill by the progressive breakage of corners and edges. Ball rationing is the regular addition of make-up balls of more than one size. The largest balls added are aimed at the largest and hardest particles. However, the contacts are governed entirely by chance, and the probability of inefficient contacts of large balls with small particles, and of small balls with large particles, is as great as the desired contact of large balls with large particles. Ball rationing should be considered an adjunct or secondary modification of the principle of selecting the make-up ball size to break the largest particle present. Empirical Equation In 19521,2 the author presented the following emerical equation for the make-up ball size: B - ball, rod, or pebble diameter in inches. F = size in microns 80 pct of new feed passes. Wi - work index at the feed size F. Cs - percentage of mill critical speed. S — specific gravity of material being ground. D == mill diameter in feet inside liners. K - 200 for balls, 300 for rods, 100 for silica pebbles. Eq. 1 was derived by selecting the factors that apparently should influence make-up ball size selection and by considering plant experience with each factor. Even though Eq. 1 is completely empirical, it has been generally successful in selecting the proper size of make-up balls for specific operations. But an equation based on theoretical considerations should be used with more confidence and have wider application. The theoretical influence of each of the governing factors listed under Eq. 1 was accordingly considered in detail, as described below, and a theoretical equation for make-up ball sizes was derived. Derivation of Theoretical Equation Ball Size and Feed Size: The basis of this analysis is that the largest ball in a mill should be just sufficient to break the largest feed particle into several pieces, excluding occasional pieces of tramp oversize. In this article the size F which 80 pct passes is considered the criterion of the effective maximum particle feed size. The smallest dimension of the largest particles present controls their breaking strength. This dimension is approximately equal to F. As a starting point for the analysis it is assumed that a 1-in. steel ball will effectively grind material with 80 pct passing 1 mm, or with F- 1000µ or about 16 mesh. The breaking force exerted by a ball varies with its weight, or as the cube of its diameter R. The force in pounds per square inch required to break a particle varies as its cross-sectional area, or as its diameter squared. It follows that when a 1-in. ball breaks a 1-mm particle, a 2-in. ball will break a 4-mm particle, and a 3-in. ball a 9-mm particle. This is in accordance with practical experience, as well as being theoretically correct. Confirmation of this reasoning is supplied by the Third Theory of Comminution," which states that the work necessary to break a particle of diameter F varies as F. Since work equals force times distance, and the distance of deformation before breaka4e varies as F it follolvs that the breaking force should vary as F½ These relationships are expressed in Table I, with a 1-in. ball representing one unit of force and breaking a 1-mm particle. This establishes theoretically the general rule used in Eq. 1 that the ball size should vary as the square root of the particle size to be broken. Ball Size and Work Index: The work input W required per ton" varies as the work index Wi, and the

Jan 1, 1959

By RALPH HAYES SWEETSER

IRON ore and bituminous coal are the two basic raw materials for the whole iron and steel industry. The ore furnishes the iron and is absolutely necessary-all iron and steel products come directly or in- directly from the iron ores. The bituminous coal furnishes the carbon needed for the smelting of the ores and for the fuel used in all the processes of iron and steel manufacture. The necessary carbon could be furnished in some other form besides bituminous coal. In fact, it is only since the Civil War that bituminous coal has been the chief source of the carbon for metallurgical fuel. For many years only charcoal made from the forests furnished the carbon for smelting iron ores. About 90 years ago, anthracite coal was first used as blast-furnace fuel and for many years continued to be the chief blast furnace and steel making source for carbon. Even in my own blast-furnace experience, I have used charcoal in Canada and anthracite in Pennsylvania for smelting ores in an iron blast furnace. Bituminous coal, now almost exclusively the source for the carbon used in smelting iron ores, also furnishes most of the heat used in the steel-making processes. It is seldom used in blast furnaces in its natural condition, hut is first coked in beehive, or in by-product coke ovens; such bituminous coal is called "coking coal." Bituminous coal that is suitable for making the producer gas used in the open-hearth steel process is called gas coal. Any bituminous coals suitable for making blast-furnace coke or foundry coke, or that can be satisfactorily used for making producer gas, are classed as metallurgical coals and as such are to be considered in my proposed plan for the evaluation of metallurgical coals. According to Bureau of Mines Bulletin No. 449 these coals comprised 22 per cent of the bituminous coals mined in this country in 1923.

Jan 1, 1926