Search Documents

By S. F. Urban, G. Derge

AT the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for a large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions [f] operation. The most important general conclusion reached was that the time a heat is held under a reducing slag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. PROCEDURE The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. Companion slag and metal samples were taken just prior to slag-off and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional 13 heats. Slag sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from tie furnace in a well-slagged carbometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace heats. The Big Wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness, and was finally adopted as the most satisfactory design. The Long Wedge Mold (b) was a 2 by 2 by 5 ¼ -in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 2 ¾ in. long, and ¼ in. maximum thickness. The Small Wedge Mold (c) was 2 by 2 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness.

Jan 1, 1947

By AIME AIME

NATURE was in a smiling mood on December 18, 1883. On that day, Chester Alan Fulton, the sixty-first President of the American Institute of Mining and Metallurgical Engineers, was born, and she endowed him with every good quality within her reach - looks, physique, intelligence, and character. Brought up in the valley of the Hudson River, with the mighty Palisades which make it the "Rhine of America," he has lived up to his early promise - as a man, as an engineer and as a friend.

Jan 1, 1943

By B. C. Craft

Development and exploratory work in Mississippi during 1934 was rather active, resulting in the expansion of the proven area and the drilling of a number of important wildcat wells. Mississippi showed a decrease in drilling operations during 1934. There were 36 completions from 18 counties during this period compared with 58 completions from 22 counties during 1933. There was a considerable decrease in activity in the Jackson gas field in Hinds and Rankin counties with only 9 completions, resulting in 8 gas wells and 1 dry hole compared with 17 gas wells, 2 oil wells and 7 dry holes during 1933. Leasing and geophysical work was reported from several sections of Mississippi last year. Extensive exploration and drilling were carried on in Lamar, Hancock, Pearl River, Greene and Stone counties and on the flanks of the Jackson anticline. Exploration will be continued in these areas during 1935. Four important wildcats were completed during 1934, all of which were reported as being structurally high, but without having important shows of oil or gas. These tests were: Hix and Germany's, J. J. Newman Lumber Co. No. 1, sec. 21-4N.-15W., Lamar County, abandoned at 3520 it. in the Wilcox; United Gas Public Service Company's Davis No. 1, sec. 30-1N.-5W., Greene County, abandoned at 7439 ft.; Gulf Refining Company's May L. Williams No. 1, sec. 33-5S.-17W., Pearl River County, abandoned at 4800 ft.; and Clarke County Oil Company's S. B. Kirkland No. 1, sec. 10-2 N.-16E., abandoned at 4002 ft. in the Eutaw. Another interesting wildcat was Gulf Refining Company's Dantzler Lumber Co. No. 6, sec. 22-4S.-llW., Stone County, abandoned at 7700 ft. (according to reports below the Selma chalk). A total of 114 of the 132 gas wells completed in the Jackson gas field are still producing and have a combined open-flow capacity of 4,145,-696,000 cu. ft. Four of the abandoned gas producers were never connected to the lines. The open-flow capacity of three wells in the Amory field is approximately 1,000,000 cu. ft. Producing against a line pressure of 50 lb., the demand during December greatly exceeded the capacity.

Jan 1, 1935

By AIME AIME

0 N March 5, at Carnegie Hall, Cleveland, the Ohio Section held a joint meeting with the Cleveland Engineering Society, and the local sections of the American Chemical Society, American Society of Mechanical Engineers, and the American Society for Steel Treating. Prior to the meeting there was an informal dinner attended by 50 men. Then followed an address, "The Principles of Corrosion Protection," by Ulick R. Evans, the well-known British specialist in this problem. There were 266 present, presided over by Zay Jeffries, president of the American Society for Steel Treating and a member of the Cleveland Engineering Society. The address was well received and some discussion followed

Jan 1, 1929

By Reed W. Hyde

Some information has been published on the sulphur dioxide concentration of gases from D wight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes Over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide notation concentrates mixed with minus 20.mesh oxide ore, the mixture carrying 16,8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily. to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO z might be utilized, a series of runs was made to determine the concentration ofSO2 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1 2 to 1 in., ('1 4 to 3% in. and (3) 6 to 5% in. The averages of the determinations from each series are platted On the graph (Fig, 1). The vertical scale shows the percentage by volume of SOz (as determined by the Reich method), and the horizontal scale shows the time e~pressed as percentage of the total sintering time. Sintering was considered to be complete when no SOz could be detected in the gases. In all cases the depth of bed was 4 1/2 in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which SO2 determinations were made could not be measured, but has been calculated from the SO2 Content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume usually will drop slightly toward the middle of the period and increase toward the end. However, this made is a reasonable approximation. several interesting features are brought out by these data. In general, the published data on SO 2 concentration in sintering under ordinary conditions show a high SO2 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SOz in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum SO2 concentration is obtained 234 min. after

Jan 1, 1944

By F. M. Hamilton, H. F. Ameen

Results of a laboratory investigation of some sintering variables are presented. The effect on physical properties of mix component variation and rate of cooling of the sinter is illustrated by crush and tumbler test results and data of reducibility tests and microscopic examination of sinters are shown. The results of using solid additions in the mix to improve bed permeability are given. SOME of the variables encountered in the sintering of iron ores and their effect on sinter properties have been investigated at the Jones and Laughlin Ore Research Laboratory in Michigan. Ores requiring agglomeration before blast furnace utilization may be classed as coarse, intermediate or fine. Coarse iron ore is considered similar to a — 1/4-in. Mesabi wash ore containing some 95 pct of its particles between 94 in. and 100-mesh. Intermediate iron ore is considered similar to our New York State magnetic concentrates in which all the particles are — 20-mesh and about 60 pct are +100-mesh. Fine ores are considered as being at least 100 pct —100-mesh. This paper will deal only with the two coarser classifications. Most of the work has been done in a small experimental batch unit previously described in an AIME1 paper. Results being obtained form a basis for present and future trials in production sinter plants. It is expected that new production units that may be added in the future will benefit from laboratory studies. In general, the results reported here are obtained by laboratory study, but it is Experimental Sinter Machine: The laboratory sinter machine employed in the work consists of a chamber with 1 sq ft of grate area. It is mounted on

Jan 1, 1951

By H. F. Ameen, F. M. Hamilton

Results of a laboratory investigation of some sintering variables are presented. The effect on physical properties of mix component variation and rate of cooling of the sinter is illustrated by crush and tumbler test results and data of reducibility tests and microscopic examination of sinters are shown. The results of using solid additions in the mix to improve bed permeability are given. SOME of the variables encountered in the sintering of iron ores and their effect on sinter properties have been investigated at the Jones and Laughlin Ore Research Laboratory in Michigan. Ores requiring agglomeration before blast furnace utilization may be classed as coarse, intermediate or fine. Coarse iron ore is considered similar to a — 1/4-in. Mesabi wash ore containing some 95 pct of its particles between 94 in. and 100-mesh. Intermediate iron ore is considered similar to our New York State magnetic concentrates in which all the particles are — 20-mesh and about 60 pct are +100-mesh. Fine ores are considered as being at least 100 pct —100-mesh. This paper will deal only with the two coarser classifications. Most of the work has been done in a small experimental batch unit previously described in an AIME1 paper. Results being obtained form a basis for present and future trials in production sinter plants. It is expected that new production units that may be added in the future will benefit from laboratory studies. In general, the results reported here are obtained by laboratory study, but it is Experimental Sinter Machine: The laboratory sinter machine employed in the work consists of a chamber with 1 sq ft of grate area. It is mounted on

Jan 1, 1951

By J. R. Spencer

When supplies of high pressure mercury or other liquids are required in analytical work, it is convenient to have the source of supply at a relatively constant pressure and available in sufficient volume to satisfy the requirements of the apparatus in use. It is also desirable that the pressuring device be as simple and as inexpensive as possible and convenient to operate. This pump combined with a small storage reservoir containing gas under pressure has the attributes of (1) positive control of the maximum output pressure through the use of a regulator in the low pressure air supply; (2) an increasing capacity as the rate of withdrawal of mercury from the pressured system is increased; and (3) simplicity, requiring only the use of a lathe, drill press, and welding unit in its construction. DESCRIPTION Essential parts of the pump are shown in Fig. 1. In appearance the unlt is similar to the usual steam pump in common use in industrial applications although considerably smaller in size. The main differences lie in the area ratio of the air and mercury pistons and in the design of the air valve mechanism. Approximate diameters of these pistons are 4.25 in. to 0.375 in. respectively, giving an area ratio of about 130 to 1. The air piston (2) is attached to the end of shaft (4), with the mercury piston being merely a reduced extension of the shaft. Mercury intake and discharge to the pump are controlled by high pressure check valves that screw into the ports indicated at (6). Air supply is controlled by the valve assembly mounted on top of the

Jan 1, 1950

By E. van Walsum

Tunneling methods through rock have, since the successful development of explosives, relied almost solely on blasting. Over the last ten years, rock-tunneling machines (moles) have been developed and some major projects have been carried out successfully with the use of such machines, which rely on the destruction of rock by mechanical means rather than blasting. Various other basically new methods are presently under study, such as the use of laser beams, water jets, etc. For practical purposes, there are presently only two methods commercially available: 1) blasting or 2) tunneling by mole. A contractor would choose at present either one method or the other. Both methods have their advantages and disadvantages (Fig. 1). The thought has occurred that the next practical development in rock- tunneling technology might be a combination of the best features of the mole technique and those of the blasting technique. A preliminary evaluation of this approach indicated that there is definitely a good potential for fruitful developments along these lines. My purpose is to place on record some of the thinking and some of the ideas which were developed along these lines and to point out certain areas where development efforts are required. In trying to find an improved tunneling technique, we looked in particular for the following qualities: 1) safety, 2) continuity, 3) uniformity, 4) automation, and 5) flexibility. TUNNELING BY BLASTING Conventional tunneling by means of blasting proceeds generally in recurring sequences of events: 1) drilling, 2) loading, 3) firing, 4) mucking-out, and supplementary operations (such as scaling and lining). These four operations (drilling, loading, firing, mucking) proceed one after another.

Jan 1, 1970

Mr. John J. Porter, Chicago Ill. (communication to the Secretary†):—Mr. Baker's account of his experiences with stock-distribution has been particularly interesting to me, as it

Jan 1, 1905

By G. R. Wilms

In a recent investigation1 on the properties of chromium, and of Cr-10 wt pct W and Cr-5 wt pct Mo alloys at elevated temperatures, it was found that intercrystalline cavities developed in all of these materials during tensile creep at 950°C, and that the cavities led to intercrystalline fracture. There were some interesting differences, however, between the cavities produced in the pure metal and those in the alloys; these differences, moreover, were associated with a difference in ductility. The relevant conditions of creep testing are specified in the captions to Figs. 1 and 3. Chromium showed the presence of quite large intercrystalline cavities, Fig. 1, and these were more or less randomly distributed around the boundaries. The chromium alloys, on the other hand, showed the presence of both small cavities and cracks at the grain boundaries, Fig. 3; it is apparent that the cracks are formed by the linking together of the small cavities. Moreover, the cavities and

Jan 1, 1960

By W. C. Lacy

A WIDE variety of metalliferous deposits in Peru shows a close and consistent relationship to intrusive and extrusive igneous rdcks. This relationship furnishes a clue to the comp(osition of ore-bearing fluids and to the timing in separation of these fluids from differentiation magma Conclusions presented here are based on ten years' study of a large number of metalliferous deposits in Peru. The most important of these areas are shown in Fig. 1. The structural relationship of meta1 mineralization to the intrusive series and of the members of the series to each other can be illustrated by three examples: I The well described Cerro de Pasco (Ref. 1, p. 160) sulfide mass shown in Fig. 2 is localized along the ' eastern contact of an agglomerate-filled crater. Quartz-monzonite porphyry and related intrusive breccias, which in places border the pyrite mass On west, are replaced by the pyrite and cut by later transverse vein structures. Late unmineralized but

Jan 1, 1958

By AIME

A GEOLOGIST --one versed in geology, the science which treats of the history of the earth and its life, especially as recorded in the rocks; that is Webster's definition. William Embry Wrather-one of the country's foremost geologists who heads the U. S. Geological Survey; this is the 1948 President of the Institute. He has studied the geology of areas on the face of the earth as far-flung as Texas and the Balkans, and now heads the world's largest staff of geologists. Vital statistics on Dr. Wrather would show his place of birth as Brandenburg, Ky., the year 1883. He will celebrate his threescore and five years of full living the twentieth of this month. As is usual in biographical sketches of this nature, the formative years of youth, and in many ways the most important years of one's life (since professional tendencies as well as many important personal decisions are evidenced before the teens are left behind) are passed over with the mere fact noted that a degree was earned at such and such educational institution. And so we note that Dr. Wrather received his Ph.B. degree at the University of Chicago in 1907, and followed up that degree with two years of graduate study.

Jan 1, 1948

By J. H. Swisher

The solubility of graphite in CaO-S2O2-Al,O3 slags was measured by equilibrating slag samples with graphite crucibles and CO gas. Carbon contents as high as 2 ut pct were obtained in CaO-saturated, CaO-A1,O3 slags, and 1.3 wt pct in slags of the composition CaO.Si0,. Although the observed conditions for Sic formation were in agreement with those predicted from thermodynamic data, CaC, was found to form at a lower temperature than predicted frotn thermodynamic data. From measurements of the equilibrium carbon content as a function of CO Partial pressure, it was found that carbide ions dissolve in CaO-A12O3 melts with a valence of minus two. The carbon content increased with CaO concentration in Ca0-Al,O3 melts and increased with SiO, content along the CaO'AlO3-CaOSi0 join in the ternary system. When solid CaC2 was added to CaO-A12O3 and CaO-SiO2-A12O3 slags, it was found that one of the oxides in the slag was reduced by the carbide (Al2O3 in the forrner and SiOz in the latter). In electric furnace steelmaking, a double-slag practice is frequently used to meet alloy specifications. Initially a flush slag, which is oxidizing in nature, is used to remove phosphorus and carbon from the steel bath. Later in the refining period, the flush slag is replaced by a highly reducing carbidic slag. When calcium carbide is formed in or added to a finishing slag, the slag is effective as a desulfurizing agent and also permits alloying elements such as chromium, vanadium, and tungsten to be added to the slag in the form of oxides. The oxides are readily reduced by calcium carbide, thereby minimizing the use of expensive ferroalloys. More work has been done on the thermodynamics of silicon carbide in slags than on calcium carbide. Baird and alor' and Kay and alor' determined the free energy of formation of Sic by measuring the partial pressure of CO in equilibrium with solid silica, silicon carbide, and graphite. Using a similar technique, they determined SiOz activities in CaO-SiOz and Ca0-Si0,-A1203 slags. Rein and chipman3 also determined the free energy of formation of Sic using slag-metal equilibrium measurements. A literature survey has uncovered only one experimental study of the behavior of CaC, in slag systems. Shanahan and cooke4 report the results of some preliminary experiments on the solubility and stability of CaC, in a CaO-A1,03 and a Ca0-Si0-A1,03 slag at a temperature of about 1500". The carbon solubility as CaC, in a slag containing 50 pct CaO and 50 pct A1203 was reported to be 0.6 pct. They also review earlier work on the binary CaO-CaC, system. A eutectic exists in this system, but various investigators disagree on the eutectic temperature and composition. eal has given an explanation for carbide furnace erruptions in terms of the thermodynamic properties of CaC,; his analysis is not based on experimental data, but on compiled data for the free energies of formation of CaC, and CO.' , These data for steel-making temperatures are all extrapolated from the results of low-temperature measurements. In the experiments described in this paper, slag samples were equilibrated with graphite crucibles and with mixtures of CO and argon or with CO gas at 1 atm total pressure for measurement of the carbon solubility. Most of the work was done on Ca0-A1203 binary slags, although in some experiments CaO-SiO, and Ca0-Si0,-A1,03 slags were used. EXPERIMENTAL Slag samples of the desired composition for the solubility measurements were obtained by blending pre-fused master slags. The master slags were prepared by fusing mixtures of reagent-grade CaC03 with either A1,03 or Si0, in a graphite crucible. The master slags were crushed, then decarburized in air in a muffle furnace at 1200O C. A schematic diagram of the apparatus is shown in Fig. 1. The source of carbon for the solubility meas-

Jan 1, 1969

By AIME

WILLIAM WALLACE MEIN, known to his intimates as "Will" or "Billy", is a mining engineer who has taken the fundamentals of successful mining--operating, engineering, and financial-and applied them to the founding of new industries. Born in Nevada City, Calif., in 1873, Will Mein grew up in an atmosphere of mining, and began to develop his sound judgment in a practical way before starting his formal technical education. As a young man he supplemented his early observations by helping his father, Captain "Tom" Mein, on mining work in California and Alaska. He then went with his father to the Rand, and after a period of milling experience as operator and shift boss he became, in 1894, manager of the chlorination of gold ores at the Robinson mine.

Jan 1, 1947

By J. J. Cosgrove, J. E. Warren

A general model which approximates the effect of cross- flow has been developed to give a practical method for predicting the waterflood behavior of a stratified reservoir. The model is based on a modification of Dietz's theory and allows for variations in both the permeability and hydrocarbon pore volume. In the particular cases considered, it is assumed that the permeability can be characterized by a log-normal distribution and the hydrocarbon pore volume by a normal distribution. A simple graphical method which enables the practicing engineer to predict the behavior of a stratified system is presented The results obtained by the proposed method are compared with those obtained by the Dykstra-Parsons method. As a result of this study the following conclusions have been drawn: (1) The effect of cross-flow in a stratified system can be appreciable, particularly at very favorable or very unfavorable mobility ratios; (2) Under normal conditions, the effect of variations in the hydrocarbon pore volume can be neglected; and (3) The failure to use all of the available permeability data can lead to large errors in the prediction of the behavior of a stratified reservoir. INTRODUCTION Various methodshavebeenproposedto characterize and to predict the waterflood behavior of a stratified reservoir. Most of the methods assume that the reservoir is composed of discrete homogeneous continuous layers. With this model, the degree of stratification can be measured by several parameters based on core-analysis data. Among these are the Lorenz coefficient1 and the variation of a log-normal permeability distribution? The behavior of stratified systems is usually predicted by the Stiles, Dykstra-Parsons method or some modification of these. In both of these methods the reservoir is divided into discrete homogeneous layers with no cross-flow between layers. In the Stiles method the mobility ratio is assumed to be equal to unity while in the Dykstra-Parsons method it is allowed to take on any value. Other predictive methods have been proposed; method allows for cross-flow between the beds and a method by Schmalz and Rahme6 correlate.s the recovery directly with the Lorenz coefficient. In this new approach, which is essentially a continuous analog of Hiatt's method, the effects of both mobility ratio and cross-flow between the beds have been included. It is assumed that the permeability can be represented by a log-normal distribution and the hydrocarbon pore volume or porosity by a normal distribution. These types of distributions have been observed by several authors, 1,2,4 and most field data seem to confirm their observations; e.g., if these distributions are assumed and there is a 1:l correspondence between porosity and permeability samples, the commonly encountered linear relationship between porosity and the log of permeability is obtained. Since, in many field cases the permeability and poro sity data are truncated or cut-off at predetermined upper and/or lower values, the effect of discarding part of the data was investigated with the proposed method. A better technique for truncating the data is suggested. THEORY In the derivation of the method to be described in this paper the following assumptions are made: 1. Capillary forces are negligible per se; their effects are only manifest in the relative permeability curves. 2. The fluids are immiscible, incompressible and homogeneous. 3. The reservoir is horizontal and uniformly thick; it is initially liquid saturated i.e., connate water and oil. 4. The reservoir is composed of discrete layers, each having its own permeability, porosity and connate water saturation; each layer is homogeneous,

Jan 1, 1965

By J. Chipman, N. J. Grant, H. L. Bishop, H. N. Lander

Data of several studies on the equilibrium between molten iron and open hearth-type slags have been combined to determine some of the chemical reactions involved in steel-making. Effects of slag composition and temperature on the iron oxide activity, distribution of sulfur between slag and metal, and the carbon content of the metal are discussed. Also, an overall reaction for the equilibrium between sulfur and oxygen is presented. DURING the past 15 years, a number of significant equilibrium studies have been carried out between liquid iron and simple basic and acid slags in an effort to throw light on the chemical reactions involved in steelmaking. This paper is a summary of the experimental reports on investigations which have been conducted at the Massachusetts Institute of Technology, and of related work in other laboratories. The investigations summarized in this paper include the works of Fetters and Chipman1 and Taylor and Chipman,' which dealt with simple slags that are similar to those found in the open hearth. The sulfur determinations of the slag-metal tests of Fetters and Chipman as reported by Grant and Chip-man" are included. Also, the investigations by Win-kler and Chipman' and Grant and ChipmanQ f more complex slag systems are included in this summary. The experimental procedure is described in detail in each of these papers and will not be discussed. Since the previous reports have been somewhat independent, it is desirable to review and combine the data of the various investigations to determine, as accurately as possible, the reactions in the slag-metal systems of the open hearth. It is the object of this report to present the combined data in such a way as to enhance their utility and applicability. Oxidizing Power of Slags of the System (CaO+MgO)-Si0,-FeO in Equilibrium with Carbon-Free lron The slags selected to determine the iron oxide activity in equilibrium with pure liquid iron were those containing less than 2 pct each of P,O,, MnO, or A1,0, on a weight percentage basis. The method used to calculate activities of iron oxide in liquid slags was that developed by Taylor and Chipman.' The solubility of oxygen in molten carbon-free iron under pure iron oxide slags can be expressed by the following eauation —6320 log (pctO)-------------— + 2.734 [1] where T is the absolute temperature. The oxygen solubility values as determined from Eq. 1 were used throughout this study to calculate the iron oxide activity. The iron oxide activities of slags of various iron oxide contents are plotted in Fig. 1 as a function of the basicity, which is defined as the ratio (pct CaO + pct MgO)/pct SiO,, and are based on molecular percentage values of the components. The percent (FeO), is the total iron content in the slag calculated to FeO. Fig. 1 shows that as the basicity increases at constant mol pct (FeO),, the iron oxide activity increases rapidly and reaches a plateau which extends on the basicity scale from about 1.3 to 2.3; the iron oxide activity then decreases rapidly until a basicity of about 3.0 is reached, where it tends to level off. The solid portions of the curves represent the experimental data of Fetters and Chipman and Win-kler and Chipman. Their experimental heats were made in magnesia crucibles, and hence the slags were saturated with magnesia. The broken lines on the left represent the experimental data of Taylor and Chipman, who used a rotating crucible. In general, these slags contained less than 3 pct MgO. The absence of data for slags containing less than about 40 mol pct (FeO), and basicity ratios greater than about 2.5 made it necessary to calculate curves using ionic concepts of slags. The broken lines on the right, which disregard the solubility limits of di and tricalcium silicate and lime, were obtained by following the treatment of Flood and Grjotheim,"

Jan 1, 1957

By AIME

AS with Phil Kraft, referred to on this page last month, travel has always held a great fascination for Raymond Frank Baker and for that reason he determined to become a geologist. He had heard that geologists travel and that was what he wanted to do. Now as chief geologist for The Texas Co. his early wish has been fulfilled-he spends almost one third of his time journeying' from one oil field to another. Mr. Baker was born in New Haven, Conn., on Jan. 11, 1892, and went through the public schools in New Britain. A stalwart New Englander, he attended Yale and in 1912 received a degree in civil engineering. For a year following this he worked as a civil engineer for the New York Central Railroad, but his early urge to travel widely could not be satisfied here. So in 1913 he re-entered Yale and until 1916 studied mining and economic geology. He had a little taste of field work, which later became so enjoyable to him, in the summer of 1915 when he worked with the U. S. Geological Survey as a geologic aid. In 1916 he made his first contact with The Texas Co. when he entered their Tulsa office as a geologist. This early career was interrupted by service in the

Jan 1, 1947

By George E. Beavers

It is well to understand at once that converter gas is always mixed with copper blast-furnace gas at Copperhill before entering the Glover tower, and, at times, roaster gas is also added along with the converter and blast-furnace gas. Fig. 1 is introduced to show the variations in the sulfur dioxide content of the gas and the ability of the acid-plant operator to control the variations, resulting in a very even grade at the Gay-Lussac tower entrance. The sulfur dioxide content of the gas entering the Gay-Lussac tower must be low and regular to assure low niter consumption. The blast-furnace gas alone is rather uniform as regards sulfur dioxide content and the variations, as shown in Fig. 1, are chiefly caused by converter changes—out for charging, slag pouring, copper pouring, and, of course, the "finish." The combined gas during the converter finish is, at times, almost free of oxygen and the sulfur dioxide content reaches 13.0 per cent. At such times air is added at the Glover tower.

Jan 1, 1934

By NEWTON B. KNOX

CHILEAN mining in the public mind is rightly associated with copper. Chuquicamata with its great hill of copper-bearing granodiorite as well as Sewell and Potrerillos with mineralized volcanic necks together can supply a good proportion of the world's normal necessities of that metal. Chile is an extremely long and narrow country, averaging only 109 miles wide. Its eastern frontier is the Andes and it is on the western slopes of these mountains that the great copper deposits have been discovered. West of the Andes a great longitudinal depres sion has permitted accumulation of nitrates and other soluble salts in the arid north; in the north center it is hidden by a series of cross ranges, but in the center a moderate rainfall makes it the country's most important agricultural region. In the south this depression is drowned and gives rise to a series of straits and fiords. This enormous cleft in the earth's crust is separated from the sea by a coast range of moderate elevation which in the south is represented by a series of islands and mushroom-shaped peninsulas

Jan 1, 1945