Search Documents

By S. Isserow

RECENTLY, a description of the wartime work in this laboratory on the U-Si phase diagram was published. This diagram was available earlier in the open literature; as were Zachariasen's crystal structure identifications for the compounds in the system. The uranium end of the phase diagram is shown in Fig. 1. The most recent work on this system has emphasized the peritectoid E phase, of particular interest for a number of reasons. The early work provided evidence of this phase's resistance to corrosion in water and of its slight ductility. Further information on these properties has been obtained here. Work elsewhere4 has provided evidence of stability under irradiation. This body-centered-tetragonal phase is relatively isotropic compared to the more usually applied a or ? uranium phases. Unlike the other compounds in this system, it contains no Si-Si covalent bonds.3 In addition, consideration on the basis of Pauling's concepts leads to the conclusion that in the E phase, uranium has a higher valence than in any of the other phases. Definition of the composition of the ? phase has been of prime concern in the study of this alloy. Evidence is presented below that its silicon content is slightly higher than that of stoichiometric U8Si, the composition frequently assigned this phase on the basis of Zachariasen's identification. This work on the composition required careful attention to the method of dissolving the alloy for analysis, since apparently low silicon contents could be found under certain conditions, see Appendix. Preparation: Melting, Casting, and Heat Treatment—Almost all the samples were from castings with a diameter of 13/4 or 2 in. and about 1 ft long, weighing 10 to 15 lb. The U-Si charge was melted by heating to about 1650°C in an induction heated vacuum furnace. Beryllia crucibles were used at first, but were replaced by zirconia-washed graphite as the technique of keeping the carbon content low enough (about 500 ppm) was mastered. The alloy was bottom-poured at about 1650°C into graphite molds. A few small buttons, weighing no more than 50 g, were prepared in a small arc melting unit.' Since cast material has a preponderance of uranium and U8Si2, heat treatment is necessary to ob-tain the ? phase by the solid-solid peritectoid reaetion. Once obtained, the ? phase is stable to room temperature, obviating the need for speeial attention to the method of cooling after epsilonization, see Fig. 1. It was found desirable to epsilonize at 800°C for a week. For some purposes, in which residual uranium and/or U8Si2 are tolerable, shorter periods may be adequate. The temperature of 800°C is not critical, since essentially the same results were obtained from 785° to 825°C. Further departure from this epsilonization range is inadvisable.

Jan 1, 1958

By Richard D. Mills

Throughout the mining industry, many companies perform sophisticated business and financial analyses of proposed capital investments. However, once the project is approved, it is never reevaluated. At best, there is an attempt to control capital costs and minimize overruns. The post-installation appraisal, a formalized review of investment performance, may prove helpful. Typical Project Review A typical capital investment is approved after business and financial benefits have been reviewed with management.* The financial data shown to management often include a net income statement, cash flow analysis and summary economic data similar to those shown in Table 1 overleaf. These financials report the expected impact of the project on the corporation financial statements. This project is a rudimentary example of a capital investment decision. An actual project would undergo a more sophisticated analysis incorporating depletion benefits, deferred taxes and a detailed cost breakdown. The example project has several financial benefits that could result in management approval. For example, it provides an immediate net income benefit to the company, generates positive cash flows every year of the project life and has a discounted cash flow rate of return of 25 percent. However, it also has the disadvantage of a long payback period. A sensitivity analysis would show which areas of the analysis have the greatest impacts on profitability. Post-Installation Program Objectives The post-installation appraisal goes beyond the analysis shown in Table 1 by comparing actual results to those projected in the original economic analysis. The post-installation program has three primary objectives: 1. To provide a periodic performance review of major spending programs. 2. To review decision-making and evaluation procedures. 3. To provide a means of controlling individual project investments. The first major function of the post-installation program is the periodic review of actual performance of projects and investment programs, identifying those factors which proved critical to the health of investments. This review will serve to keep management abreast of progress, provide a comparison of actual performance against expectations, and provide valuable information that can be used for improving future economics. The second major function of the program is to perform a continuous review of the decision-making process. This includes testing of evaluation procedures, forecasting techniques, and logic used in making decisions. An information system should be set up whereby original evaluations and historical performance data gathered under the appraisal program are documented for use by evaluators and management when assessing past and future investment proposals. Such data should be particularly useful in evaluating new and developing types of operations and in activities where companies repeatedly reinvest. The primary purpose of this feedback system is to sharpen estimates to assure that they are realistic and attainable. The appraisal program also provides assurance that consistent evaluation procedures are being used throughout a company, leading to improved procedures

Jan 1, 1985

By W. Hume-Rothery

IN recent interesting papers,1,2 Bardos et al. have described ternary Laves phases of the type A2(BsSi) and A4(B5Si3) where A = titanium vanadium, niobium, and so forth, and B = manganese, iron, cobalt, or nickel; other more complex formulae have also been established. In these phases, silicon plays the part of the smaller B atom of a Laves phase AB2, and the interatomic distances show that the effec- tive silicon radii lie between 1.16 and 1.21Å, and are thus very much smaller than the metallic radius of silicon for CN = 12. It does not seem to have been pointed out that these small atomic radii are almost the sape as the normal covalent radius of silicon (1.174Å). If, therefore, silicon acts as an acceptor of electrons as suggested by Bardos et al.,1 it appears to do so, not by the building up of a negatively charged silicon ion which would be large, but by the formation of what are very nearly or may be actually normal covalent bonds. Since a covalent bond contains two electrons, its formation would reduce the number of electrons available for bonding in other parts of the structure, and in this way the effect of silicon in stabilizing the o phase at high electron concentrations might be understood.

Jan 1, 1965

By J. Intrater, E. S. Machlin

In a study of grain boundary sliding in superpure Copper (99.999 pct),&apos; bicrystals of a specific shape were used, Fig. 1. That shape was adopted in order to minimize the deformation of grains on both sides of the boundary due to clamping. Another requirement was to obtain bicrystals with a rnicroscopically straight boundary, Fig. 2. Single crystals of predetermined orientation (growth axis parallel to <310>) were grown in a graphite mold from seed crystals. The apparatus for growing single crystals consisted of a vacuum system, argon purification train, vycor tube (in which a graphite mold was placed), a carriage for the induction coi1,and a Lepel (7-1/2 KW) high-frequency converter. The graphite mold was heated by induction and the charge in turn was heated by conduction. The induction coil was moved by means of a motor at a speed of 1 1/2 in. per hr. Single crystals of two different orientations were grown from the melt in one-half of a split graphite mold, Fig. 3(a). Two such crystals were then placed in contact with each other in another split mold, Fig. 3(b) using tapered inserts. The pair of crystals was then remelted starting 2 in. from the top to insure that the whole top portion of the crystals was maintained molten. By moving the induction coil

Jan 1, 1960

By David M. Parkes, Junie Lindsay

A review of the movement of coal in water is undertaken from a practical rather than a theoretical view point. Installations are described in which coal is transported on gradients down to 2.5&apos; and others which move coal at a water-coal ratio of 1:l by weight. The water cycle of the hydraulic mining system is discussed. In many applications this can be a closed circuit. The coal dewatering system is illustrated, making particular reference to the problems of storage of coal-water mixtures between the mine and the plant. Water treatment is done in thickeners down to 100 ppm which is normally sufficient for re-circulating through high pressure pumps and monitors.

Jan 1, 1978

By Edgar C. Bain

In studying the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900" C. (1650" F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement— the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1 shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general 2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 1, 1924

By Edgar C. Bain

In studying the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900" C. (1650" F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement— the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1 shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general 2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 1, 1924

By Edgar Bain

IN STUDYING the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900° C. (1650°, F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement-the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1. shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 2, 1924

By Oliver C. Ralston

This paper reports the results of the use of salt in some research work carried on during the past 3 years at the Salt Lake City Station of the Bureau of Mines, which is quartered in the University of Utah, whose Metallurgical Research Department cooperates with the Bureau. Only the work involving the use of salt is described. The authors wish equal credit given to J. F. Cullen, C. L. Larson, C. Y. Pfoutz, C. E. Sims, H. C. Neeld, R. W. Johnson, F. G. Moses, N. C. Christensen, and G. H. Wigton, who have all in some way contributed toward the success of this work, while connected with the station in one way or another. Lead Metallurgy Popularly Supposed to be Without Problems In lead metallurgy it is difficult at first to find metallurgical problems, as the prevailing conception has been that lead is so easily concentrated in its various ores and so easily reduced to its metallic form that the only progress possible is that involved in cheapening methods of mining and of reduction. Most of the problems usually considered are of minor nature and do not involve radical metallurgical changes. During the three years of work of the Salt Lake Station, the following classification of problems in the metallurgy of lead has been made: Oxidized Ores. 1. Ores containing only lead. 2. Ores containing lead and silver or gold. 3. Ores containing lead and zinc, with or without silver. Sulphide Ores. 1. Ores of pyrite carrying some lead. 2. Ores of complex zinc-lead-iron sulphides. 3. Complex sulphides containing precious metals.

Jan 1, 1918

By J. H. Ffolliott

ALL, of the prospects that later became mines in the Ducktown district were discovered prior to 1854, and most of them were exploited before the turn of the century. It is the purpose of this paper to discuss the exploration and current development of the Boyd mine, discovered in 1853. It is in the heart of the Ducktown Basin, in the extreme southeast corner of Tennessee, and is being developed by the Tennessee Copper Co. GEOLOGY The geology of the district has been fully described in many papers. Probably the most complete description is that of Emmons and Laney.1 The rocks of the district are considered to be of Lower Cambrian age and are a part of the Great Smoky formation, consisting mainly of interbedded graywacke and mica schist, in which the ore deposits occur. The ore bodies are included in an area of about 6 sq. miles, 2 miles wide and 3 miles long striking N. 45° E., and may be grouped into three general lode systems. The northeast system, including the East Tennessee, London and Burra Burra ore bodies, and the southeast group, comprising the Polk County, Mary and Calloway deposits, are all characterized by relatively high copper values. The ores of the central system, which includes the Eureka, Boyd, Old Tennessee and Cherokee ore bodies, are low in copper and high in total sulphide content. Boyd mine lies roughly halfway between the Old Tennessee and Eureka ore bodies [ ] and 2500 ft. in the hanging wall of the Burra Burra mine (Fig. 1). Elevation of the surface is about 1725 ft. above sea

Jan 1, 1942

By D. R. Mitchell

This paper discusses some of the fundamental physical and chemical characteristics of coal in Illinois that affect its preparation for the market. At the present time preparation consists almost entirely of sizing and hand-picking. The washing of coal has almost entirely disappeared from the state. This is a rather startling fact when one considers that in the year 1908 Illinois outranked all other states in the quantity of coal washed and a few years later, in 1912, 85 washing plants were reported. Two reasons are apparent for this change. One, which is probably the most important, is that immense areas of comparatively clean coal were opened; the other is that many of the early washing plants were inefficient, so that washed coal was looked upon with disfavor in many trade centers. Objectives of Operators Some of the outstanding preparation aims being given due consideration by operating men are: 1. The greatest possible production of lump and domestic sizes which bring in the market at least $1 per ton more than the fine sizes or screenings. 2. Efficient screen sizing with as little breakage as is consistent with economical operation. 3. The removal of extraneous ash and sulfur. 4. Utilization of low-priced screenings. 5. Suppression of dust in domestic coal shipments. Preparation Underground To get the greatest possible production of the larger sizes, preparation must start at the face. Improvements in blasting and loading have increased the sizes larger than 2 in. by as much as 20 per cent. at some mines. Tiffany and McKitterickl report the results of an investigation they made at a mine in southern Illinois in which, by a carefully controlled

Jan 1, 1931

By M. E. de Morton

Low frequency-internal friction measurements on annealed chromium have shown a marked increase in damping below - 40°C which is strongly strain amplitude dependent. An interpretation of these results is given in terms of the motion of antiferromagnetic domains assumed to exist below - 40°C. A time effect on internal friction was measured after slight overstraining. After heavy deformation a pemzanent, five-fold increase in internal friction was observed at -45°C and the character of the internal friction us temperature curve markedly changed. Full recovery of damping was not attained until after heating to 800°C. A qualitative interpretation of some of these effects is given. THE aim of this preliminary investigation was to study the internal-friction characteristics of chromium containing comparatively small quantities of interstitial solutes in the fully annealed and heavily worked condition. Marked anomalies in a number of physical properties of chromium at temperatures near 40°C have been observed1 and an investigation by neutron diffraction&apos; has shown that chromium at room teyperature is weakly antiferromagnetic with a Nee1 temperature at approximately 200oC. No irregularities in the degree of antiferromagnetic ordering have been observed at -40°C, the transition temperature, and a complete explanation of this transition in chromium is still awaited. Recently weiss3 has suggested that an ordering effect of nitrogen in the face-centered interstices of the bcc lattice of chromium could be responsible for the superlattice detected below 200 °C in the neutron diffraction experiments. EXPERIMENTAL MATERIAL AND METHOD Specimens 10 by 0.030 in. diam were prepared from ingots of arc-melted electro-deposited chro-

Jan 1, 1961

By K. D. Jacob, W. L. Hill

THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;1 calcium aluminum phosphates such as pseudowavellite;2 and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island.3 Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized,4 most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world.3,5 Later these samples were reanalyzed by a new and more reliable method of determining flourine.6,7 The revised results with interim additions of new samples, published a few years ago in a brief summary,&apos; are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit.

Jan 10, 1954

By Nobuhiro Takahashi

PROLOGUE The Yaguki mine, which is located near the southern end of the Tohoku region, Japan, near the coast of the Pacific Ocean, had had a long history as a copper mine, but had not been operated since 1925. About 30 years later it was reopened by Nittetsu Mining Company, and in 1958 a small flotation and magnetic separation plant, a so-called test plant, started production. The ball mill the author first met, a 8x4x4x7 ft tricone mill, called No.1 mill, had started running at that time. With his experience in initial, running of this mill he realized that the ball mill was not simply a preparatory process to flotation, but a determinant factor for flotation performance, an energy-consuming and costly process, and that its operation control was an important task in the plant (1). The working part of an operating ball mill is the ball load inside, whose properties govern the grinding performance. Its size distribution affects the efficiency greatly and the capacity is nearly proportional to its weight. When a ball mill operates for a long period of time with a constant and consistent addition of renewal balls, wear and renewal of balls are balanced, and an equilibrium ball load is formed. A stable equilibrium load is the primary requirement for a stable ball mill operation. However, renewal ball size would be the most influential factor affecting efficiency and capacity of operating ball mills. To improve efficiency, to increase capacity, or to get finer product, attempts to find out the optimum size assortment of renewal balls should be made. When re-

Jan 1, 1976

By R. Lagneborg

WhEN mechanical twins initiate cracking it has been proposed1 that the friction stress for dislocation motion, in the Cottrell criterion for brittle fracture2 should be replaced by the stress required to propagate a twin, ttp. TF is the fracture stress, d the grain diameter, ß a geometric constant, u shear modulus, and y the effective surface energy. Since TTp is likely to vary with grain size, it cannot be substituted by a constant in Eq. [I]. If an expression for the energy change caused by a twin in a stressed material could be obtained, it is in principle possible to compute the critical size of the twin, i.e., the size at which the system can decrease its energy spontaneously, as a function of applied stress, thus giving the stress required to just barely propagate the twin, i.e., TTP. Consider a circular twin disc with a radius r and having a lenticular cross section, Fig. 1. Twin dislocations3 of strength b exist in the twin boundary parallel to the twin plane, one loop on each atomic plane. Assume that the total numbers of loops, n, can be replaced by one circular loop of a multiple dislocation, nb with a radius r. The energy change of the system, AW, due to such a twin in an applied stress field can then be calculated: The first term is the total twin surface energy, the second the elastic energy due to the twin dislocations, and the third the energy released by the twin in the applied stress field. yt is the twin boundary energy, r, the radius of the dislocation core, and T the applied

Jan 1, 1968

By A. Blake Caldwell

Northwest frontier is here defined as Alaska, the Yukon, the Northwest Territories and northern British Columbia. The mineral potential of this area is great and will unfold in the decade ahead but now the largest single producer is the Pine Point lead-zinc mine in the NWT about 1200 km north of Edmonton, Alta., close to the south shore of Great Slave Lake. The mill, initially designed for 4540 mtpd, was expanded to 7250 mtpd in 1969. This operation is described in detail in Mining and Concentrating of Lead and Zinc, Vol.1, Chapt. 17, SME/AIME in the article by W. H. R. Gibney.

Jan 1, 1971

By Fortunato Pereira Gamba

The Department of Narino (formerly included in the Department of Cauca) is a narrow band about 170 km. (100 miles) wide in the southern part of the Republic of Colombia, near the boundary of Ecuador, as showu in the sketch-map, Fig. 1. Its capital is Pasto, a small city of 25,000 inhabitants; the pri~icipal towns are T?querres, Cumbal, Ypiales, Barbacoas, and Tumaco. The port on the Pacific ocean is Tumaco, and traffic in the interior is carried partly on the Patia river (steam navigation to the fluvial port of Barbacoas), and afterwards overland over poor roads by human bearers or on mule-back.

Jan 1, 1913

By W. F. Rogers, J. A. Stewart, P. J. Kalish, E. O. Bennett

Detailed descriptions are given of materials, apparatus and the experimental procedure used to study the effect of bacteria on sandstone permeability. The factors affecting permeability during injection of bacterial suspensions which have been investigated are: (I) concentration of bacteria; (2) core permeability and median pore size; (3) species of bacteria, mode of aggregation and relative size; (4) injection rate or pressure differential; (5) mean pressure; and (6) depth of penetration of bacteria. The investigation demonstrated that bacteria cannot reduce core pertneability to zero and that their effect on permeability is subject to definite limitations. Remedial or permeability restoration studies also were made. Acidization in combination with reverse flow war found to be an effective method for restoring permeability In cores partially plugged with bacteria. The relationship between the bacterial quantities in the laboratory tests and those found in field operations is discussed. The linear laboratory flow data have been translated into terms of field radial systems; these data indicate the most practical methods of maintaining injection rates in the presence of bacteria are to increase injection pressures or hydraulically fracture the formation. INTRODUCTION It has long been known that various bacteria flourish in the above-ground components of oil field water-injection systems. The presence of these bacteria has led to the suspicion that they might enter into the causes for reduction of injection well permeability, but only recently has an attempt been made to describe the effects quantitatively.1 Biocides are used in many cases without a firm knowledge as to whether the bacteria are killed, or if they are, whether the dead cells affect formation permeability. This project was undertaken as part of a study to determine the effect of bacteria, residual oil and precipitated solids such as iron sulfide or calcium carbonate on the permeability of sandstones and to learn whether any of these materials adversely affect brine injectivity in secondary recovery or disposal operations. This report deals with that portion relating to the effect of bacteria. MATERIALS CORES Three different permeability ranges of Berea sandstone cores were used in the study. The range of initial, absolute brine permeabilities kj were: high — 278 to 400 md: medium—130 to 162 md; and low—17.7 to 48.3 md. The permeability data for the cores used in the tests are included in Table 1. All cores were cut to a nominal 1 in. diameter. Following air permeability determinations, they were molded with an epoxy resin in 1.5 in. ID aluminum sleeves. The sleeves had drilled and tapped holes for intermediate pressure connections along the length of the cores. After molding, the high- and medium-permeability cores were trimmed to 4 in. in length and the low-permeability cores to 2 in. These lengths resulted in pore volumes of approximately 10.9, 10.4 and 4.4 ml, respectively, for the high-, medium- and low-permeability cores. Pressure-transmitting channels were drilled through the plastic into the core proper, using the sleeve holes as drill guides. Width and depth of channel penetration into the core proper were approximately 0.03 in. and 0.05 in., respectively. Three pressure taps were used with all cores; for the high- and medium-permeability cores the taps were spaced 1 in. apart; for the low-permeability cores the taps were spaced 0.4, 0.8 and 1.2 in. from the inlet end. Pore size distributions were calculated from restored-state capillary pressure curves for representative cores in each of the three permeability ranges. In each case the pore size range with the greatest percentage of the pore space included the very small pores up to 0.5 micron in radius. The median pore radii were in the 5.5 to 6 micron range for the high-permeability cores; in the 4.5 to 5 micron range for the medium-permeability cores; and in the 3.5 to 4 micron range for the low-permeability cores.

Jan 1, 1965

By J. N. Butler, R. J. Morris

A series of organic collectors has been developed which successfully float synthetic secondary uranium minerals, such as autunite, carnotite, and torbernite. Recoveries up to 97 pct have been obtained. With cleaning of rougher concentrates, ratios of concentration as high as 15:1 are possible on head assays of 0.10 to 0.50 pct U 3 O 8. Additions of certain base metal salts aid in recovery and materially increase the rate of flotation and selectivity of the collectors for the synthetic minerals. Flotation tests on natural uranium minerals have not yet equaled results obtained on the synthetics, although these collectors do give better results than conventional collectors for nonsulfide minerals. RAPID increase in mining and milling uranium ores during the past seven years and the discovery of large tonnages of uranium-bearing material too low in grade to stand the cost of leaching have developed considerable interest in possible methods for beneficiating these marginal ores. Such ores are generally classed as those containing less than 0.10 pct U3O8. Development of a beneficiation method that would give both high recovery and high ratio of concentration would also make possible the beneficiation of higher grade ores and would provide higher grades of feed to existing leaching plants. Although considerable research and testing on physical or physico-chemical beneficiation of domestic uranium ores has been done in the past, to the best knowledge of the authors only a single application of physical beneficiation is now in operation on a commercial scale. Flotation has been attempted on the basis of mineral association rather than by direct concentration of the contained uranium minerals. Flotation studies conducted on this project on certain ores gave recoveries of 60 to 70 pct of the uranium by the use of conventional flotation agents such as oleic acid, but ratios of concentration were in the order of 1.5:1 to 2.5:1. Subsequent cleaning to upgrade the concentrates rapidly increased losses in the cleaner tailings, which were not later refloated in the rougher flotation. Selection of Collector: In selecting desirable organic collectors for these oxide systems, a thorough study was made of the relationship between structural characteristics and collector activity by an examination of the behavior of a number of different functional arrangements present in a variety of organic molecules, (see Fig. 1). It is generally accepted that a collector must have a relatively long-chain hydrocarbon radical and a chemically reactive elec-trophilic center. Such a requirement could be met by a large number of compounds, but steric effects at the uranium mineral surface, solubility, compat-ability with aqueous systems, air avidity, bond strength at the mineral surface, interfacial concentration of the collector, and diffusion rate of the formed complex from the air-water interface eliminated many as unsuitable for this purpose. Preliminary investigations were completed of possible collector designs consisting of aliphatic and aromatic hydrocarbon radicals attached to stable combinations of nitrogen, oxygen, sulfur, and halogen electrophilic centers, Fig. 1.Tests were made to determine melting point spans, solubility of mineral-collector combinations in various solvents, reactions with soluble uranium salts, contact angles, and floatability by semi-quantitative beaker methods.&apos; Contact angle determinations were not too useful because of the fine particle sizes of available mineral samples. From the foregoing study it appeared that nitrogen-sulfur electrophilic centers coupled with straight-chain saturated alkyl hydrocarbon radicals would hold the most promise for floating secondary uranium minerals. As the dithiocarbamate compounds can be made to combine these attributes they were selected for further study. The dithiocarbamates form a parallel structure to the xanthates, with the fortuitous exchange of

Jan 1, 1957

By E. J. Ripling, S. I. Liu

IT has been shown in a number of recent publications that much information on the mechanical behavior of metals can be gleaned by first deforming test specimens under one set of conditions, and then evaluating the effect of this deformation by means of a subsequent tensile test. A straining procedure of this type has been applied to study the flow behaviors of a number of metals.1, 2 In these studies the prestraining and testing were both tensile strains, while the straining temperature was varied between the prestraining and testing steps. These data indicate that there is a more or less general flow behavior exhibited by all metals which are pre-stretched at one temperature and then tested in tension at a second temperature. Prestraining a metal at a high temperature produces a lower yield strength during the subsequent low temperature strain than would the same total strain at the lower temperature. On reversing the order of the strains, low temperature prestraining produces a higher yield strength during the subsequent high temperature straining than would a single high temperature strain of the same magnitude. Unlike the flow behaviors, the fracturing characteristics of metals when prestrained under one set of conditions and tested under a second set of conditions is quite material dependent. The fracture behavior of a number of steels2" as well as of a commercially pure zinc,4 have been investigated by these two-step tests and was found to depend upon the position of the transition temperature with respect to the prestraining and testing conditions. Since these fracturing phenomena are complicated by the appearance of the transition temperature, it has been difficult to reliably define the basic effect of a two-step straining procedure in fracturing. Metals crystallizing in the face-centered cubic system do not exhibit transition temperature effects so that the mechanical characteristics obtained on these materials could serve as a base for two-step straining behaviors. Consequently groups of specimens of the aluminum alloy 24s-T4 were prestrained various amounts at room temperature in either tension or compression after which these strained specimens were further strained to failure, or tested in tension, at either room or some lower temperature. Other groups of 24S-T4 specimens were prestretched at various low temperatures after which these were tested in tension at room temperature. These straining techniques then made it possible to compare the behaviors of aluminum with the behaviors previously presented for steels. Material and Procedure The commercial aluminum alloy 24S-T4 in the form of 3/4 in. rods was used in this investigation. The material was subjected to the following treatments before machining: 1—resolution treating at 920" & 10°F for 45 min, 2—quenching in water at room temperature, and 3—aging at room temperature for four days. The re-heat treated material was then machined to either of the specimen shapes shown in Fig. 1. Fig. la shows the threaded-end specimen used for prestraining in compression. Fig. 1b shows the specimen used for both prestrain in tension and final testing. The material subjected to precompression in the form of the specimen shown in Fig. la was re-machined to the specimen shape in Fig. 1b for final testing. Prestraining in tension and final testing were done without any intermediate machining. All straining was performed on a 10,000 1b Riehle tensile testing machine. Tensile strains were conducted in a specially designed concentric fixture which produced an eccentricity of less than 0.001 in." The change in diameter at the minimum section of

Jan 1, 1954