Search Documents

By S. Stopek, E. D. Hinkley, R. H. Rediker

Epitaxial heterojunctions have been prepared by melting the lower -melting-point semiconductor of the interface between two dijferent semiconductors. when the temperature is reduced, the melted material recrystallizes, having alloyed into the higher -melting-point semiconditctor. The electrical and elcctro-optical properties of such single-crystal heterojunctions between GaAs and Gash and between p-type InAs and n-type Gash are the subject of this paper. The forward current varies as exp (AV), where A is substantially independent of temperatuve. For Gds-Gash heterojunctions at temperatures above, 370°K, if the current-voltage relationship were to he expressed as exp (qV/nkT), then n would he less than unity. The injection luminescence associated with forward current is, for the most part, characteristic. of the lower bandgap semicondutctor. These results can he explained by carrier injection into the lower bandgap semiconductor by tunneling through a barrier at the interface. The photovoltaic effect measured for incident photons having energies in the range between the bandgaps of the two semiconductors is much smaller than that produced by higher-energy photon The smallness of this between -the-gap photovoltaic response can he explained by the low probability for penetration of the barrier by the carriers produced in the smaller -bandgap semiconductor. THE technique of interface alloying has been used to produce single-crystal junctions between dissimilar semiconductors.' Oriented wafers are placed on a carbon heater strip, Fig. 1. so that semiconductor S1, which has the lower melting point, is supported by semiconductor S2. Electrical current passed through the heater strip produces a temperature gradient such that S2 is at a higher temperature than S1. As the temperature is raised the lower face of S1 begins to melt. Before the entire wafer can melt, however, the heater-strip current is turned off and, as illustrated in Fig. l. the melted portion recrystallizes, having alloyed into S2. Junctions have been fabricated by the above procedure between GaAs and germanium, between GaAs and GaSb, and between InAs and GaSb. Mroczkowski, Lavine. and Gatos have described the metallurgical and chemical aspects of the GaAs-Ge junction.2 The transition from GaAs to germanium is not monotonic and a portion of the recrystallized region consists of the GaAs-Ge eutectic. Since gallium is an acceptor and arsenic is a donor in germanium, since germanium dopes GaAs, and since the electrical properties of the GaAs-Ge eutectic have not been investigated, any interpretation of the electrical characteristics in terms of simple heterojunction theory would be incorrect. That the rectification of GaAs-Ge heterojunctions is not a property of the impurity doping of the GaAs or the germanium, but is most probably due to the impurity distribution in the recrystallized region, is clear from the fact that forward conduction occurred for all the GaAs-Ge interface-alloy junctions (whether they be n-n,n-p. p-n. or p-p) when the germanium was biased positively. The electrical characteristics of these GaAs-Ge heterojunctions will not be discussed further in this paper. Electron-beam microprobe analysis of GaAs-GaSb heterojunctions showed that the transition from arsenic to antimony atoms was without structure. and that the transition occurred within a 2 to 3 region.' In this paper we will describe the electrical properties of the GaAs-GaSb heterojunctions as well as electrical and electro-optical properties of the InAs-GaSb heterojunctions. A band model for the junction will be proposed which can explain these properties. ELECTRICAL PROPERTIES OF GaAs-GaSb HETEROJUNCTIONS After interface alloying. in preparation for the electrical and electro-optical experiments, ohmic contacts were made by conventional means. For example. Kovar tabs clad with tin were alloyed to n-GaAs or similar tabs clad with Au-Zn were alloyed to p-GaAs. The units were mounted and then etched. All four combinations of conductivity types

Jan 1, 1965

By Steve H. Carpenter, Henry E. Otto

The explosive welding of metals is dependent upon the production of a jetting action caused by the collapsing of one metal plate against another. Successful welds are generally accomplished if the yield strength of the metals is in the range of 10,000 to 90,000 psi and the sonic velocity of the metal is greater than the detonation velocity of the explosive if direct contact explosive is being used.' Should the detonation velocity exceed the velocity of sound in the metal it may still be possible to obtain the jetting action and a good weld. However, in most cases where a high detonation velocity is used complications arise because of reflected shock waves which tear the bond apart as fast as it is put together.' Explosive welding of lead presents several problems since its yield strength and sound velocity are very low. Various values have been published3-5 for the velocity of sound in lead ranging from 2000~ to 23004 m per sec. Most of the high-order explosives have detonation velocities on the order of 6000 to 8000 m per sec, which precludes their use. The dynamites have a lower detonation velocity of around 2800 m per sec which is still somewhat too high. Lower-order explosives such as ammonium nitrate (1070 m per sec) must be used to weld lead in the as-received condition if the explosives are used in direct contact. Rather than use low-order explo'sives it was decided to alter the sonic velocity of the lead. The sonic velocity is directly related to the modulus of the material according to the following expression: Fig 1—Interface of explosive weld of lead to steel. Lead is on top As-polished Magnification 75 times as well as the yield strength. Bolling et al. 6 show that the shear modulus of lead single crystals increases from about 0.72 X1011 dynes per sq cm at 300°K to about 0.98 X1011 dynes per sq cm at 0°K, an increase of approximately 3 5 pct. This gives an increase in the sonic velocity of around 700 m per sec. Hence, the sonic velocity of lead at cryogenic temperatures is approximately equivalent to the detonation velocity of the low-order dynamites. We have obtained high-quality lead to steel explosive welds using a 40 pct dynamite in direct contact with the lead. Prior to detonation the lead was chilled with liquid nitrogen (78°K) to increase the strength and sonic velocity. Welds were made while the lead was cold. Specimen sizes were 3 by 6 in. A preset angle of 5 deg with a 0.10-in. standoff at the base was the geometrical setup used. The amount of explosive used for optimum welding of an 1/8 -in. -thick lead sheet to a steel plate was found to be 7 g per sq in. A PETN sheet explosive line wave generator was used to insure a linear detonation front through the dynamite. A photomicrograph of a lead-steel weld is shown in Fig. 1. The typical wave effect that constitutes a good explosive weld is present. When tested in shear, the weld failed in the lead, indicating that the bond is stronger than the lead base metal. Higher-order explosives were also tried without success. We believe this indicates the importance of matching the detonation velocity and the sonic velocity for successful explosive welding. Note Added in Proof. High quality explosive welds of lead to steel have recently been obtained at ambient temperature using a low velocity (1000 M per sec) free running dynamite. The weld interface obtained is comparable to Fig. 1. 'S. H. Carpenter, R. H. Wittman, and R. J. Carlson: Proceedings of the First International Conference of the Center for High Energy Forming, Syracuse University Press, syracu.se, N. Y., in press. 'A. HI Holtzman and G. R. Cowan: Welding Risearch. Council Bull., No. 104, April, 1965. 'Metals Handbook, 8 ed., p. 1062, Metals Park, Ohlo. 'J. M. Walsh, M. H. Rice, R. G. McQueen, and F. L. Yarger: Phys. Rev., 1957, vol. 108, pp. 196-216; 'L. V. Al'tshuler, K. K. Krupnikov, B. N. Ledener, V. I. Zuchikhin,

Jan 1, 1968

By James A. Barr, R. B. Burt, I. S. Tillotson

DISCUSSION Howard Howie (Knoxville, Term.)—The authors are to be congratulated on the presentation of a paper containing so much valuable information on the pipeline transportation of phosphate, as there is very little literature on the subject. The writer is especially interested in the paper, as he conceived the arrangement of the Akin and Godwin plants and was in charge of the design work and the engineering incident to their construction. The Akin and other phosphate deposits in the Tennessee phosphate area lie on beds of limestone that are very irregular. The limestone beds, after the phosphate matrix has been removed, are similar in appearance to land severely eroded by the action of water and denuded of top soil. Depressions in the limestone, called cutters, are irregular in depth with vertical or overhanging walls, having the general appearance of cracks in dried clay. They change abruptly in direction, width, and depth, and vary on the Akin tract from 1 to 25 ft in depth and from 1 to 50 ft in width. Pinnacles of limestone commonly occur in the cutters which appear, when exposed, like small clifflike islands in a river. Limestone floats also occur. The phosphate matrix fills the cutters and covers the uncuttered areas, the thickness of the cover varying continually and sometimes rather abruptly. It occurs generally as stratifications of phosphate rock and clay of varying thickness. The phosphate rock in the matrix varies in hardness and in percents of silica, lime, iron oxides, and fluorine, and the clay varies in toughness. In some places the deposit consists of narrow strata of rock almost devoid of clay streaks. In other nearby locations the clay will predominate. When it is excavated, the phosphate rock breaks into thin irregular lumps, locally known as plate rock. Limestone lumps are also excavated with the matrix. Akin plate rock is generally much softer than that occurring in other deposits in the area. Because of the above described physical and chemical variations of the excavated material, the resultant slurry varies in size distribution, specific gravity, and percent of slimes. When the rock is soft or when there is an increase of clay, the slime fraction is greatly increased as it passes through pumps and pipelines, resulting in reduced pipe friction. It is obvious that the longer the pipeline the greater the reduction of coarse fractions into fines, causing a decrease in pipe friction that cannot be accurately evaluated. The matrix is mined with a dragline that drops it into a hopper with a grid composed of 9-in. parallel bar spacings located above the hammer mill. The matrix on, and passing through the grid, is subject to the action of powerful sprays which wash it down to the hammer mill, together with any limestone lumps that are not removed before passing through the grid. The hammer mill reduces the feed to lumps of plate rock and clay, most of which will pass through the 8-in. pump suction. The mixture discharges into a pool containing the pump suction pipe. Water from a hydraulic nozzle moves the mixture to the pump suction intake. The pump, driven by a variable speed motor, is the same size as the pumps mentioned on p. 279. Provision is made to remove any lumps that lodge in a bend in the suction pipe in a manner similar to that used in the Florida phosphate fields. The hammer mill and pump units are mounted on wide steel skids so that they can be moved as the mining operation progresses. The discharge from the pump flows through an abrasion-resistant spiral welded steel pipe 8 1/4 in. actual inside diam, 8 in. nominal diam, for a maximum distance of 2200 ft, which is the limiting pumping distance for one pump. This pipeline, referred to hereafter as pipeline A, discharges into a ball mill without balls, which in turn discharges into a rotary screen attached to it that separates the slurried matrix into 11/4-in. oversize and undersize fractions. The oversize is returned to the mill for further reduction; the undersize is pumped to a Dorrco washer and then flows into a hydroseparator 160 ft in diam. In spite of the size reduction in the hammer mill and the blunging and washing of the slurry in its passage through the pump, pipeline, mill, and washer, the discharge to the hydroseparator frequently contains mud balls almost perfectly spherical. Sometimes the discharge from the 16,000-ft pipeline at Godwin contains mud balls the size of bird shot and smaller. This pipeline will be referred to subsequently as line B. Liquid caustic is added to the slurry at the Akin plant before its passage through the hydro-separator, which decreases the size of particles in the overflow by dispersion. In passing through pumps 1, 2, and 3 and pipeline B, the slime fraction in the underflow is increased by abrasion and blunging and also by continuing dispersive action of the caustic. The matrix for use in the experimental tests referred to on p. 279 was obtained from three small surface openings on the Akin tract that were made previous to the purchase of the tract by the Authority. Matrix used in the 2 and 4-in. experimental pipeline tests was taken from the three openings and proportioned to obtain a sufficient quantity that would be fairly representative of the average in the Akin deposits. Prospecting samples of matrix had been obtained from drill holes which showed no small variation in physical and chemical properties. Some of the physical variation is evident from the size distribution of solids in samples taken during the tests covering line B flows so thoroughly made by the Authority under the direction of Mr. Burt, see Table V, p. 280. Hydraulic gradients for a pipe of 8-in. diam were derived from the 2 and 4-in. pipeline tests using the so-called representative matrix as above described, and plotted on the profile of pipeline B. Gradients of other materials in slurry form passing through pipelines that bore some similiarity to the Akin matrix slurry were also plotted. After a study had been made of the hydraulic gradients plotted on the profile and the varying slurry flow that would probably occur during actual operation, three pumps were ordered, referred to as No. 1, 2, and 3 on p. 279. No. 1 and 2 pumps were installed and the third kept in reserve should the operation of 1 and 2 pumps prove satisfactory, since installation of the third pump would require an attendant, as well as the laying of 5400 ft of pipe to supply it with seal-water from the Akin plant. Subsequently, it was found desirable to install the third pump to maintain capacity when the slime fraction was low and the coarse fractions were large. Reference to Fig. 6 will show that the flow in B line goes upgrade in three locations. At the outlet at Godwin, the slurry flows between two 45" bends for an approximate distance of 18 ft to rise above the ground a sufficient height to discharge into a launder feeding the first classifier. This condition requires extra energy, which is taken care of by keeping the hydraulic gradient a sufficient distance above the high points. Although there are rather heavy upgrades in the line, the choking condition that might occur at the

Jan 1, 1953

By R. B. Burt, James A. Barr, I. S. Tillotson

DISCUSSION Howard Howie (Knoxville, Term.)—The authors are to be congratulated on the presentation of a paper containing so much valuable information on the pipeline transportation of phosphate, as there is very little literature on the subject. The writer is especially interested in the paper, as he conceived the arrangement of the Akin and Godwin plants and was in charge of the design work and the engineering incident to their construction. The Akin and other phosphate deposits in the Tennessee phosphate area lie on beds of limestone that are very irregular. The limestone beds, after the phosphate matrix has been removed, are similar in appearance to land severely eroded by the action of water and denuded of top soil. Depressions in the limestone, called cutters, are irregular in depth with vertical or overhanging walls, having the general appearance of cracks in dried clay. They change abruptly in direction, width, and depth, and vary on the Akin tract from 1 to 25 ft in depth and from 1 to 50 ft in width. Pinnacles of limestone commonly occur in the cutters which appear, when exposed, like small clifflike islands in a river. Limestone floats also occur. The phosphate matrix fills the cutters and covers the uncuttered areas, the thickness of the cover varying continually and sometimes rather abruptly. It occurs generally as stratifications of phosphate rock and clay of varying thickness. The phosphate rock in the matrix varies in hardness and in percents of silica, lime, iron oxides, and fluorine, and the clay varies in toughness. In some places the deposit consists of narrow strata of rock almost devoid of clay streaks. In other nearby locations the clay will predominate. When it is excavated, the phosphate rock breaks into thin irregular lumps, locally known as plate rock. Limestone lumps are also excavated with the matrix. Akin plate rock is generally much softer than that occurring in other deposits in the area. Because of the above described physical and chemical variations of the excavated material, the resultant slurry varies in size distribution, specific gravity, and percent of slimes. When the rock is soft or when there is an increase of clay, the slime fraction is greatly increased as it passes through pumps and pipelines, resulting in reduced pipe friction. It is obvious that the longer the pipeline the greater the reduction of coarse fractions into fines, causing a decrease in pipe friction that cannot be accurately evaluated. The matrix is mined with a dragline that drops it into a hopper with a grid composed of 9-in. parallel bar spacings located above the hammer mill. The matrix on, and passing through the grid, is subject to the action of powerful sprays which wash it down to the hammer mill, together with any limestone lumps that are not removed before passing through the grid. The hammer mill reduces the feed to lumps of plate rock and clay, most of which will pass through the 8-in. pump suction. The mixture discharges into a pool containing the pump suction pipe. Water from a hydraulic nozzle moves the mixture to the pump suction intake. The pump, driven by a variable speed motor, is the same size as the pumps mentioned on p. 279. Provision is made to remove any lumps that lodge in a bend in the suction pipe in a manner similar to that used in the Florida phosphate fields. The hammer mill and pump units are mounted on wide steel skids so that they can be moved as the mining operation progresses. The discharge from the pump flows through an abrasion-resistant spiral welded steel pipe 8 1/4 in. actual inside diam, 8 in. nominal diam, for a maximum distance of 2200 ft, which is the limiting pumping distance for one pump. This pipeline, referred to hereafter as pipeline A, discharges into a ball mill without balls, which in turn discharges into a rotary screen attached to it that separates the slurried matrix into 11/4-in. oversize and undersize fractions. The oversize is returned to the mill for further reduction; the undersize is pumped to a Dorrco washer and then flows into a hydroseparator 160 ft in diam. In spite of the size reduction in the hammer mill and the blunging and washing of the slurry in its passage through the pump, pipeline, mill, and washer, the discharge to the hydroseparator frequently contains mud balls almost perfectly spherical. Sometimes the discharge from the 16,000-ft pipeline at Godwin contains mud balls the size of bird shot and smaller. This pipeline will be referred to subsequently as line B. Liquid caustic is added to the slurry at the Akin plant before its passage through the hydro-separator, which decreases the size of particles in the overflow by dispersion. In passing through pumps 1, 2, and 3 and pipeline B, the slime fraction in the underflow is increased by abrasion and blunging and also by continuing dispersive action of the caustic. The matrix for use in the experimental tests referred to on p. 279 was obtained from three small surface openings on the Akin tract that were made previous to the purchase of the tract by the Authority. Matrix used in the 2 and 4-in. experimental pipeline tests was taken from the three openings and proportioned to obtain a sufficient quantity that would be fairly representative of the average in the Akin deposits. Prospecting samples of matrix had been obtained from drill holes which showed no small variation in physical and chemical properties. Some of the physical variation is evident from the size distribution of solids in samples taken during the tests covering line B flows so thoroughly made by the Authority under the direction of Mr. Burt, see Table V, p. 280. Hydraulic gradients for a pipe of 8-in. diam were derived from the 2 and 4-in. pipeline tests using the so-called representative matrix as above described, and plotted on the profile of pipeline B. Gradients of other materials in slurry form passing through pipelines that bore some similiarity to the Akin matrix slurry were also plotted. After a study had been made of the hydraulic gradients plotted on the profile and the varying slurry flow that would probably occur during actual operation, three pumps were ordered, referred to as No. 1, 2, and 3 on p. 279. No. 1 and 2 pumps were installed and the third kept in reserve should the operation of 1 and 2 pumps prove satisfactory, since installation of the third pump would require an attendant, as well as the laying of 5400 ft of pipe to supply it with seal-water from the Akin plant. Subsequently, it was found desirable to install the third pump to maintain capacity when the slime fraction was low and the coarse fractions were large. Reference to Fig. 6 will show that the flow in B line goes upgrade in three locations. At the outlet at Godwin, the slurry flows between two 45" bends for an approximate distance of 18 ft to rise above the ground a sufficient height to discharge into a launder feeding the first classifier. This condition requires extra energy, which is taken care of by keeping the hydraulic gradient a sufficient distance above the high points. Although there are rather heavy upgrades in the line, the choking condition that might occur at the

Jan 1, 1953

By H. Rosenthal, A. L. Jamieson

The action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,5 who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. MEthods Specimens TWO types of specimen were used: 1. Unannealed 70-30 brass CUPs formed from 0.040-in. thick sheet. Height of cup Was 13/8 in. and diameter was 17/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass)- The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was receded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (1) degreased in trichlorethylene, (2) rinsed in H2O, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 SP. gr.), (4) rinsed in H2O, and (5) dried. Amirtes Tested In selecting the amines, representatives of the three series of amines, and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By A. L. Jamieson, H. Rosenthal

The action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,5 who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. MEthods Specimens TWO types of specimen were used: 1. Unannealed 70-30 brass CUPs formed from 0.040-in. thick sheet. Height of cup Was 13/8 in. and diameter was 17/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass)- The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was receded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (1) degreased in trichlorethylene, (2) rinsed in H2O, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 SP. gr.), (4) rinsed in H2O, and (5) dried. Amirtes Tested In selecting the amines, representatives of the three series of amines, and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By H. Rosenthal, A. L. Jamieson

THE action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking. Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,' who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. METHODS Specimens Two types of specimen were used: I. Unannealed 70-30 brass cups formed from 0.040-in. thick sheet. Height of cup was 1 3/8 in. and diameter was 1 7/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass). The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was preceded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (I) degreased in trichlorethylene, (2) rinsed in H20, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 sp. gr.), (4) rinsed in H2O, and (5) dried. Amines Tested In selecting the amines, representatives of the three series of amines and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By N. K. Chen, R. Maddin, K. T. Aust

Lattice rotations occurring on the tension and compression sides during the bending of molybdenum single crystals at room temperature were followed in detail. Observations were also made concerning crystallite rotations and slip traces. &apos;The results indicated the participation of (110) as slip planes and the<111>as slip directions. Crystallite fragmentation during bending was also noted. EVERAL investigations have been conducted on pure bending of face-centered cubic metals.&apos;-" Structural changes as a result of "bend-gliding," and the importance of bending and constraints during conditions of axial stressing, have been noted.&apos;," It was evident that the mechanism by which the bending deformation occurs is more complex than the case of simple shear. Studies of the bending of body-centered cubic metals from the aspect of the crystallographic mechanism appear to be lacking. Molybdenum single crystals therefore were subjected to deformation by bending in order to determine the reaction of the body-centered cubic lattice to bending stresses. It might be expected for the bending of single crystals that lattice rotation as represented by the axis of compression would proceed toward the pole of the active slip plane and that rotation of the tensile stress axis should indicate the slip direction.&apos; It was believed therefore that a study of the tension and compression sides of bent molybdenum single crystals should give data concerning the operative slip system. Specific problems which are pertinent to the overall picture of plastic deformation were also investigated, e.g., whether the constraints offered by pure bending give rise to the deformation band, and also the nature of the asterism occurring on the tension and compression sides during the stages of deformation. Experimental Procedure Eight single crystal specimens were grown from sintered molybdenum rods 143 in. diameter using the method described previously.6 The purity of this material was reported as 99.9 pct as described elsewhere.&apos; The specimens were % to 1/10 in. in diameter x 7 in. long, with single crystals approximately 1 to 2 in. in length occupying the entire center sections of each specimen. The specimens were elec-trolytically polished using an electrolyte of 300 cc methyl alcohol, 60 cc H2SO4, 130 cc HCl, and a current density of 4 amp per sq in. Each specimen was then loaded in a bending apparatus similar to that used by Yen and Hibbard,&apos; as shown in Fig. 1. The load was applied by means of a spring and screw arrangement through four ball-bearing surfaces set 1.5 in. apart. Either the inner two bearings or the outer two (A, B, Fig. 1) were attached to a movable steel plate (D) through which the load was transmitted. Since the apparatus was mounted on a track of the X-ray apparatus, the tension or compression side of the specimen could

Jan 1, 1954

By N. A. Ziegler

IN every research it is desirable to eliminate as many variables as possible and to leave only a few to be investigated one at a time. Metallurgical problems are no exception. Some of the variables that are difficult to control are the size, the distribution, and the orientation of the grains in a metallic test piece. It is therefore very desirable to obtain isolated metallic grains (single crystals, as they are commonly called) large enough to enable one to study their mechanical and physical properties. The present investigation is a part of magnetic research work on iron and iron alloys, undertaken to obtain, if possible, the magnetic properties of pure iron (Fe). This paper will deal primarily with the preparation of single crystals of iron and their mechanical properties, while another paper, by T. D. Yensen, now in preparation, will deal specifically with their magnetic properties. The work with "single crystals" is attracting more attention every year among the investigators in metallurgy. Van Liempt1 gives an interesting summary of the work done and the different methods used in the preparation of metallic single crystals. Briefly stated, the four principal methods used are the following: 1. The cooling of a liquid metal in such a way that the crystallization would start at one point only, causing the entire liquid to solidify as one crystalline unit. This method can be successfully applied to the majority of the metals that do not have any allotropic transformations in the solid state. It has been used and described by a number of investigators,2 but it has never been successfully applied to iron on account of allotropic transformations.

Jan 1, 1930

By W. H. Emmons

IN 1922 Morey made a series of experiments in which he observed the cooling of a molten system containing H20, 9.1 per cent; K20, 17.3 per cent and Si02, 73.6 per cent. This system was confined in a bomb; it was fluid at 500° C. and exerted no vapor pressure. In cooling to 420° C. a large part of it crystallized and at that temperature much of the water had separated from the crystals and remained as steam, which built up a pressure of 4998 lb. per sq. in., a force sufficient to lift nearly one mile of granite.1 If granite, cooling at 600°, expels vapor in the process of crystalliza-tion it is reasonable to suppose that a considerably greater vapor pressure would result, and it is thought that the vapor expelled from crystallizing granitic batholiths probably has a pressure sufficient to lift two or three miles of granite. This vapor, collecting near the tops of cupolas of batholiths, is believed to exert sufficient pressure to fracture the hoods and roofs of batholiths above the cupolas. If that is true, one would expect to find that the fracture systems above cupolas are arranged in patterns that depend in part on the shapes of the cupolas. The mechanics of the situation seem to require that conical cupolas should have radial fracture patterns, that bluntly rounded cupolas should have fracture systems that are either irregular or rudely conjugated in plan, and that elongated stocks or cupolas should have fracture systems in which the fractures lie nearly parallel to the direction of the elongation of the cupolas.

Jan 1, 1934

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick&apos;s law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick&apos;s law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick&apos;s law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick&apos;s law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By H. I. Altshuler

THE mines operated by the Compañia de Real del Monte y Pachuca, Pachuca, Mexico, are in two districts, the Pachuca, and Real del Monte. The principal area of mineralization is within a rectangle roughly 10 miles from east to west and 6 miles from north to south. It contains a number of veins from 2 to 20 ft. wide, which are exploited by this mining company. The scattered position of the producing mines led to the construction of two mills between 1906 and 1908; the Loreto mill, in Pachuca, averaged 2600 tons daily, and the Guerrero mill, in Real del Monte, milled 1270 tons daily. On Feb. 1, 1929, the management decided to enlarge the Loreto mill to take the combined tonnage of both mills at that time. This economic measure required the centralization of ore delivery, which would also afford a material saving in the cost of ore transport. The centralization would give the company the following advantages over the former system of operation: 1. Beneficiation at a single mill, closer to source of materials and supplies than the abandoned- Guerrero mill. The refinery is, also in the Loreto patio. 2. Ore delivery to surface at one point (San Juan Pachuca shaft) instead of at four. 3. Elimination of aerial tramways. To show what would be required to effect this centralization, it is necessary to describe the means by which the ore was delivered to the two mills, prior to centralization. The heart of the Real del Monte district is roughly four miles from that of the Pachuca section. The producing mines in these two districts were: Pachuca district: Santa Ana mine Camelia group

Jan 1, 1934

By R. H. Heyer, J. L. Bray, M. E. Carruthers

It is well known that iron markedly improves the physical properties and casting characteristics of aluminum bronzes. The use of 1 to 4 per cent iron as the principal modifying addition has become common practice in many foundries melting aluminum bronzes. Although the beneficial effects of iron are unquestioned, there is some uncertainty regarding the structural changes caused by it in the basic copper-aluminum system. It is agreed that a new constituent appears in abundance when the iron content reaches 2 to 4 per cent. This constituent, which frequently occurs in shapes resembling clover leaves, is sometimes assumed to be an aluminum-iron intermetallic compound. If this were correct we might expect a change in the structural relationships of the matrix in the direction of decreased aluminum content. On the other hand, it has been reported that iron has a negligible effect in altering the fundamental relationships of copper-aluminum alloys1 Others2&apos;3 have reported an additive coefficient. Apparently it will be necessary to know the equilibrium relationships between the phases of the copper-aluminum-iron alloy system to establish any such theory as fact. When this has been done it may very well be that a further revision in the structural relationships may be necessary to describe the changes to be expected in commercial cast alloys. It was with this latter problem before them that the authors attempted to determine the change in the copper-aluminum relations with respect to iron. Objects of the Investigation In certain investigations carried out by the authors for a plant producing a large tonnage of cast aluminum bronzes the structures

Jan 1, 1936

By Frederick Rhines

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick&apos;s law (equation 1 below), ? in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick&apos;s law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activa-tion heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. Much of the argument concerning the properties of metals that deter-mine D and Q has been drawn from data in which variations of the quan-tities with concentration are unknown, for these data- have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concen-trations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Arthur Taggart

FLOTATION of sulphide minerals and native metals is no longer a practical difficulty. The underlying scientific principles of the method, although not explored in anything like complete detail, have been formulated with sufficient breadth so that the direction of attack on any specific case is clearly indicated. It has been known since the earliest clays of flotation that certain of the nonsulphide nonmetal minerals-e.g., sulphur and graphite-would respond to flotation by oils as sulphides do; therefore they have been grouped with sulphides in many patents. But since the development of the chemical theory of collection,1,2,3 this similarity in action has been one of the facts cited in disproof of the theory by opponents of the hypothesis.4,5,6 Air levitation? of certain oxidized minerals, both metalliferous? and nonmetalliferous, and separa-tion thereby from other oxidized minerals, is a recent development in practice, although the discovery of the method dates back 17 years.7 This paper presents evidence that the principles underlying the air levita-tion of the nonsulphide nonmetal minerals are the same as those utilized in the flotation of the sulphides and native metals. It will be apparent immediately to anyone with knowledge of mineral concentration that separation of air-levitated minerals in water from minerals not so levitated is a simple matter of water-gravity concentra-tion, the separating device employed depending solely upon the size of the particles treated and the buoyancy differences effected by the levita-tion, The usual separating means employed are: (1) a flotation machine for fine, slimy and for well aerated granular material; (2) shaking tables for granular less aerated material.

Jan 1, 1937

By Jed H. Mosgrove, Paul M. Budzak

INTRODUCTION Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 m3/s (9000 cfm) of air at his last open crosscut. PLANNING What will provide adequate ventilation? A rule of thumb in laying out a coal mine is to provide enough entries in the main entry system to keep air velocities at 2.5 m/s (500 fpm) or less; at this rate of flow, good ventilation may be expected. The intake and return air courses of a coal mine do not improve with age. Entries will deteriorate, ribs will slough, roof will fall, and clutter will accumulate. The resistance offered to air travel will continue to increase with each passing year. Providing enough airways for the present and the future cannot be emphasized too strongly. In order to better appreciate good planning and bring it into better focus, assume a hypothetical mine has the following features: entries 1.5 m (5 ft) high and 6.1 m (20 ft) wide; one intake and one return entry; the mine development is 4.8 km (3 miles) from the intake and upcast ventilation shafts; and the ventilation requirement is 141.6 m3/s (300,000 cfm) . Air travel of 4.8 km (3 miles) into a mine and the same distance back to the fan is not unusual. However, to do so with one intake and one

Jan 1, 1981

By Thomas Leonard Watson

Sulphide ore-bodies of more or less lenticular shape occurring in metamorphic crystalline schists, gneisses, and slates, and conforming closely in strike and usually in dip to the inclosing rock, have been recognized and described along the Atlantic seaboard from Quebec to Alabama. The ore-bodies do not entirely conform, in all cases, to the structure of the inclosing schists, but they sometimes cut across the foliation in dip, though conforming more closely with the direction of strike. In composition the principal sulphide mineral is usually py-rite or pyrrhotite, or both, accompanied by copper, frequently gold, and almost always some sphalerite and galenite. Other metallic ores are, so far as these sulphide bodies have been investigated, less common; silver is not uncommon, and in some of the pyrrhotite masses nickel is present in quantity sufficient to be commercially valuable. Cobalt frequently accompanies the nickel, usually in smaller amount, and the two vary much in relative proportion. Quartz and calcite are probably the most common of the non-metallic minerals. A number of silicate minerals are frequent representatives in one place or another ; garnet, am phi-bole, biotite, pyroxene, zoisite and others. The sulphide bodies of Virginia, comprising both pyrite and pyrrhotite, are among the most extensive along the Atlantic seaboard. Among the pyrite bodies may be mentioned the well-known and extensively worked mines of Louisa and Prince William counties, located on the main pyrite belt (A, Fig. 1) of the middle and northern, eastern Piedmont region in Virginia, and among the pyrrhotite bodics is the famous " Great Gossan Lead" (13, Fig. 1) of the Floyd-Carroll-Grayson coun-

Jan 1, 1908

By R. P. Agarwala, M. S. Anand, S. P. Murarka

Using the residual radioactivity technique, grain boundary diffusion of chromium in the a phase and lattice diffusion in the a and the ß phases of zirconiuttz have heen studied. The diffusivities (in units of square centiwzeters per second) have heen expressed as THE rate of diffusion of atoms along surfaces and grain boundaries is much greater than that through the bulk of metals. These processes dominate over volume diffusion at lower temperatures and can be isolated from it by virtue of the fact they yield high diffusion coefficients and low activation energies. In zirconium, however, it has been difficult to identify the volume-diffusion parameters separately. The values of diffusivities in a and ß phases yield activation energies which are much lower than those for volume diffusion calculated from semiempirical or empirical relations.1-3 Diffusion frequencies (Do) are also low, especially in the a phase, and they yield negative entropies of activation.4 Similar results have been obtained for the diffusion studies in titanium.5 It is yet to be investigated whether in these cases diffusion is controlled by some extraneous factor like high reactivity of these metals, or some different mechanism is operative as suggested by Pound et a1.6 However, Federer and Lundy,7 in a recent study of the diffusion of zir-conium-95 and columbium-95 in zirconium, and Gibbs et al.,8 in the study of impurity diffusion in titanium, found a temperature dependence of D, Do, and Q. Their study yielded low values of Do and Q at low temperatures, as has been found by other workers, and fairly high values at high tempera-

Jan 1, 1965

By Y. C. Liu

IN the study of the rolling recrystallization of face-centered-cubic metals, a most unusual observation is the frequent occurrence of a sharp re-crystallization texture of cube orientation. Although the general conditions under which this texture occurs are known,2,3 its origin is still not well understood. Based on the observed relationship between the {110}<112> deformation texture and the (113}<211> recrystallization texture, regardless of the effect of alloying elements2,4,5 or the symmetry of the deformation texture,&apos; there is a strong indication that a specific component of the deformation texture is related to a specific component of the recrystallization texture. Using the rotational reorien-tation relationship as a means of correlating the deformation and recrystallization textures, it was proposed that the deformation component which related the cube texture has {358)<523> indices."&apos; The investigation reported here was undertaken to seek experimental evidence for the validity of this proposition. Experimental Procedure Two copper single crystals having an initial orientation within 2" of (358) [523] indices were prepared in the manner described in Ref. 5. The purity of the copper was between 99.94 and 99.97 pct. The original dimensions of the crystals were as follows: specimen A, 0.465 in. thickness, 0.844 in. width, and 0.955 in. length; specimen B, 0.535 in. thickness, 1.120 in. width, and 1.36 in. length: Rolling was done on a laboratory rolling mill according to the following schedule: 0.010 in. per pass to 50 pct reduction in thickness, 0.005 in. per pass to 70 pct reduction inthickness, 0.002 in. per pass to 85 pct reduction in

Jan 1, 1958