Search Documents

By Arnulf Muan, Hobart M. Kraner

Ferromanganese alloys react with aluminu-silica brick in blast furnace hearths and cause the formation of new phases with low refractoriness and consequent failure of the refractory lining. The nature of these reactions is explained on the basis of petrographic observations, thermodynamic data, and Phase equilibrium considerations. Animproued hearth design resulted from these findings. The production of ferromanganese in blast furnaces presents many problems which are not encountered in the production of iron in the same furnaces. One of the most serious of these problems is the rapid failure of refractories caused by their reaction with the ferromanganese metal. The present paper describes such a "hearth attack", its symptoms, causes, and cure. Following an introductory discussion of operating practice in ferromanganese blast furnaces, results are presented of a petrographic examination of samples from a furnace which had to be shut down because of refractory failure. The causes of this failure are then analyzed on the basis of petrographic observations combined with thermodynamic and phase equilibrium data available in the literature. The latter type of data were subsequently used as a guide in recommending improvements in hearth designs which have since proven themselves successful in practical operations. I) FERROMANGANESE BLAST FURNACE PRACTICE It is considered good practice to blow in a furnace on iron and operate it in this way for a period of time preliminary to producing ferrornanganese. During this time, iron generally penetrates the bottom refractories six or more feet below the original working surface of the hearth. Not only does this metal pervade the joints to these depths, but the pores of the refractories are usually also filled by molten iron. The high throughput of the iron furnace provides ample heat to maintain a high temperature in the hearth refractories. This, together with a high ferrostatic pressure, causes porous clay brick of the hearth to shrink. During subsequent use of such a furnace in ferromanganese production, the iron in the pores of hearth brick if; replaced to some extent by ferromanganese. The replacement is usually not complete. This is probably due to the lower metal throughput and lower prevailing temperatures resulting from this in the brick of the hearth bottom. When the ferrornanganese furnace is banked—or when the temperature in the furnace falls due to a furnace delay—-manganese oxidizes even though the atmosphere is largely CO. Considerable expansion accompanies this oxidation of manganese from metal to oxide. The hearth refractories are then subjected to the disintegrating forces of the volume expansion. These forces may in extreme cases be large enough to lift the furnace off its mantle supports as was described in a previous paper.' When cooling takes place slowly, however, and the temperature remains at a fairly high level, the refractories undergo fluxing action by the MnO. This latter reaction and the reduction of SiO2 of the clay brick is the general subject of the present paper. The observations to be described herein were made on a ferromanganese furnace located at the Johnstown plant of Bethlehem Steel Co. The furnace was lined entirely with clay refractories and had operated on iron for 266 days and on ferromanganese for 96 days prior to being taken off because of a hearth wall failure. II) PETROGRAPHIC EXAMINATION AND CHEMICAL ANALYSIS The photograph reproduced in Fig. 1 shws a cross section of the upper part of an 18 by 9 by 4-1/2 in. bottom block removed from the blast furnace. This brick came from a depth of approximately 6 ft below the original working face of the bottom. It will be noted that the 4-1/2 in. dimension is almost the same as when the brick entered the furnace. Three characteristically different zones marked I, II, and III on the print of Fig. 1 are apparent. Results of chemical analyses of the original brick and samples from each of these zones are listed in Table I. Petrographically the various zones were characterized as follows: The central zone marked I was essentially un-reacted brick. The microstructure consisted of fine needles of mullite, and the pores in this entire area were filled with iron. This is characteristic of

Jan 1, 1962

By R. A. Wattenbarger, H. J. Ramey

A systematic study has been made of the application of the real gas pseudo-pressure m(p) to short-time gas well testing. The m(p) function can be used in real gas flow problems to account for the variation of viscosity and z-factor with pressure. A mathematical model was solved numerically to generate solutions of various real gas flow problems. The effects of turbulence, formation damage and wellbore storage were included in the model. The analysis of simulated well tests showed that the interpretation methods normally used for liquid flow are generally accurate when the m(p) is used. For practical rates without turbulence, the solutions are not rate-sensifive, and the flow capacity.. kh and skin effect can be determined accurately from either a buildup or a drawdown test. However, the kh calculated from a drawdown test can be significantly low when turbulence is present. A case was simulated in which this error wa.s 36 percent. Turbulence does not affect the determination of kh from buildup tests. The proper determination of kh from p and pa buildup and drawdown plots is developed by analyzing their relationship to the m(p) method. A simple equation is given that can be used for long-range gas well performance forecasting. This expression is compared with a method pre-sended by Russell et al." Introduction The formation flow capacity and wellbore damage condition can be determined for liquid-producing tests by means of buildup and drawdown tests. These tests make use of short-time pressure transient data rather than stabilized flow tests that are often used for gas well testing. Tracy' presented a method of gas well testing that was based on ideal gas equations and utilized p2 buildup plots. This method was shown to be good for low pressure wells. MatthewsZ suggested plotting p and using an average slope and average gas properties. This method was more successful on high pressure wells. Al-Hussainy, Ramey and Crawfordh howed that variation in gas properties could be simplified by using the real gas pseu do-pressure m(p). Some cases showed that the use of the m(p) function Original manuscript received in Society of Petroleum Engineers office Aug. 8. 1967. Revised manuscript received June 11, 1968. Paper (SPE 1835) was presented at SPE 42nd Annual Fall Meeting held in Houston Tex., Oct. 1-4. 1967, and at SPE 4th Annual Eastern Regional ~eetin$ held in Pittsburgh. Pa., Nov. 2-3. 1967. 0 Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. 'References given at end of paper. provided an accurate method of interpreting buildup and drawdown tests. Because the work of Al-Hussainy et al. included only a few actual cases, there was a need to explore the use of the m(p) method for a greater variety of flow conditions. The occurrence of turbulent flow around the wellbore often is an important factor in gas well testing. Swift and Kiel,' and Carter et a1.' treated turbulence in gas well testing, but did not consider the variation of viscosity and z-factor with pressure. This paper presents the results of an investigation of the application of the m(p) method to buildup and drawdown testing. Vhe investigation included the effects of turbulence, formation damage and wellbore storage. Gas Flow Equations To formulate the mathematical model, many of the assumptions usually used in well testing theory are applied. The system has radial geometry with a closed outer boundary and is composed of a horizontal porous formation that has uniform and isotropic rock properties and uniform thickness. Allowance is made, however, for a radial region of reduced permeability near the wellbore. This region represents formation damage. The geometry of the system is shown in Fig. 1. Darcy's law does not always apply to gas flow. A more general expression is needed for non-Darcy, or "turbulent" REGION OF DAMAGED PERMEABILITY SEALED BOUNDARIES ClRCULAR WELL BORE Fig. 1—Radial flow model. AUGUST, BT7

Jan 1, 1969

By Elmer Weber, W. M. Baldwin

Solid lead obeys a single parabolic weight increase vs. time law. In contrast, liquid lead undergoes three successive parabolic weight increases vs. time laws, the first of which has a low constant relative to the latter two. The conversion times for the change from one parabola to the next decrease with increasing temperature. IN recent reports on the subject,1,2 it was noted that zirconium and titanium scale in air by a complex mechanism. The scale first forming on the metal is protective to the extent that it gives a low constant, K, for Tammann's, and Pilling and Bedworth's parabolic equation: w² = Kt [1] relating weight increase, w, due to chemical reaction of the metal with the air, and time, t. After hundreds of hours of apparent stability in some cases the first scale yields to another that offers little protection to the metal. This transition from one scale to another, from a slow parabolic oxidation reaction to a fast one, was not due to impurities in the atmosphere or incidental effects (changing environment, etc.) but was a specific behavior of the metal itself, the transition occurring at definite times (dependent on temperature) and showing other reproducible traits. In view of this behavior how can long-time service behavior be predicted from short-time laboratory tests, not only in the case of these metals, but in any case? Certainly a systematic study of the type of scaling behavior described above—wherever it is found—would help to answer this question. The present paper is a report on the behavior as it is found in lead—the only metal to the authors' knowledge for which the behavior has been described at all, if inadequately, for our present purpose.* At least four oxides of lead are known, of which one occurs in two allotropic forms. They are ß (red) tetragonal PbO stable up to 486°C;8 a (yellow) orthorhombic PbO stable from 486°C up to its dissociation temperature in air at about 2300°C;9 minium or Pb3O4 which from the dissociation pressure data given in Fig. 1 decomposes to PbO at 540°C in air; lead sesquioxide or Pb2O3,; and lead dioxide or PbO2 which, according to Fig. 1, decomposes in air at 400°C to minium. In view of the high dissociation temperature of PbO, lead will scale up to at least its boiling point. Further, it is known that oxygen is almost insoluble in liquid lead.'V his implies a fair probability that an oxide scale would not dissolve in the molten metal and would afford the same protection to lead in the liquid state as in the solid. All of the oxides of lead for which specific gravity data are available are more voluminous than an equivalent weight of metal or a lower oxide from which they might form, hence the scales will be in compression. Lead oxides are known to be ductile, so it would be anticipated that they would form coherent nonporous scales. It is not surprising to learn, then, that both solid and liquid lead scale according to the Tammann, and Pilling and Bed-worth law.14,15 (Gruhl states that at 600°C and above lead oxidizes linearly with time because of "spitting" of the scale.) The parabolic constants K reported by various investigators3,14-16 are badly scattered, however, as shown in Fig. 2. The oxides formed on solid lead were described as being reddish-brown but were not chemically identified by Pilling and Bedworth.15 Gruhl's descripdin³ of the appearance of the scales On his liquid samples indicates that a (yellow orthorhombic) PbO is formed initially on the specimens but gives Way eventually—at least at temperatures below 486 °C— to .ß (red tetraunal) PbO, and that below 540°C minium—Pb3O4 :is firmed at an even later time as an overlay on either the red or yellow PbO. Fig. 3 is a graphical interpretation of Gruhl's description. Gruhl does not indicate any change in the parabolic scaling rate as yellow PbO converts to red. He does indicate that minium reduces the scaling rate, al-

Jan 1, 1953

By J. T. Norton, A. L. Mowry

The monocarbides of the A subgroup elements in the fourth and fifth group of the periodic table in addition to being hard and refractory are of special interest in that they are isomorphous in crystalline structure. They are cubic with a sodium chloride type structure in which the metal atoms are essentially close packed in a face-centered cubic arrangement with the carbon atoms placed in the interstices between. Interstitial structures of this close packed type were first investigated systematically by Egg1 and he gave the rule for their formation, stating that the radius ratio of the nonmetal to the metal atom should not exceed the value of 0.59. The carbides of interest are those of titanium and zirconium of the fourth group and vanadium, columbium and tantalum of the fifth group. Table 1 shows the radius ratio using the Goldschmidt radii for 12 coordination for the metal atoms and the diamond radius for the carbon atom. It will be noted that while there is considerable variation in the size of the metal atom, in all cases the ratio is smaller than the limit of 0.59 placed by Hägg. It has been known for some time that these cubic carbides are soluble in one another, at least to some extent or, in other words, the metal atoms can be replaced, one by another without destroying the stability of the structure. Since the stability of these close packed interstitial substances appears to depend more upon geometry than upon the exact chemical nature of the atoms involved, it is of interest to examine the possibilities of replacement in these carbides in some detail. Hume-Rothery2 has pointed out the importance of the difference in size of solute and solvent atom as a factor in limiting the solubility in simple binary solid solutions. Largely on an empirical basis, he states that if the difference in size between solvent and solute atom is more than 14-15 pct of the solvent atom, the range of solubility is very restricted. The atom size was based on the distance of closest approach in the elements involved. While there is some question as to how one should calculate the size of the metal atom in the carbide structures, reference to Table 1 will show that zirconium is the largest and vanadium the smallest of the group and that the difference is about 15 pct. The Ti-Zr difference is about 9 pct and the others are smaller. Thus one would predict that if the size factor controls the solubility, all of the pairs except VC-ZrC would have wide or complete solubility whereas this latter pair is on the border line and might have restricted solubility. The purpose of the present investi- gation was to examine the solubility of the several pairs of carbides by heating them together until equilibrium was established and then examining the product by X rays. Previous Work Agte3 and his associates prepared various transition metal carbides and determined the melting points of binary mixtures. He concluded from the shapes of the melting point curves that there was extensive solubility in the case of the cubic carbides. Umanskii and his colleagues made an investigation of a number of pairs of the cubic carbides, using X rays and plotted lattice parameter vs. composition curves for the systems TaC-Tic, CbC-Tic, TaC-ZrC and CbC-ZrC. All pairs showed a continuous series of solid solutions. The first two pairs gave a linear relation while the latter two showed a negative deviation from Vegard's law. Kiefer and Nowotny, in a paper which became available after the present work was well advanced, investigated the binary pairs of the five cubic carbides by means of X rays. Relatively few points were obtained and results indicated that in some cases, at least, equilibrium was not reached at the temperatures used. The results indicated that solubility in the VC-ZrC system was not complete. All of the results of previous investigations indicated the desirability of a more detailed study. Materials The raw materials used were mono-carbides of titanium, zirconium, vanadium, columbium and tantalum and were the purest which could readily be obtained commercially. Spectrographic qualitative analysis showed that the CbC and TaC contained less than 1 pct

Jan 1, 1950

By L. W. Holm, G. G. Bernard

Laboratory experiments were conducted to determine the effect of foam on gas flow in porous media. Previous studies have indicated that foam may be applicable as a restrictive agent in influencing underground gas flow. Foam was found to be exceedingly effective in reducing the permeability of porous media to gas. Consolidated and unconsolidated sands with specific permeabilities of 100 to 146,000 md had, in the presence of foam, gas permeabilities that were less than 1 per cent of the specific permeability; in many cases the gas permeability was practically zero. Foam reduced the gas permeability of loose sand to a much greater degree than that of a tight sand. For example, the permeability of a 125,000-md sand was reduced to 3 md while the permeability of a 4,000-md sand was reduced to 7 md. This effect should cause, to some degree, selective plugging of high permeability channels in various oil displacement processes. The presence of oil in a porous medium decreased the effectiveness of foam in reducing gas permeability; apparently oil acts as a foam depressant. However, it was found that certain foaming agents were very effective in reducing permeability even. in the presence of oil. Also, continuous injection of other foaming agents increased their effectiveness, when oil was present. The effect of foam on permeability of porous media to gas was studied as a function of foaming agent concentration and injection rate, absolute permeability, total pressure, pressure gadient, length of porous system, brine concentration and time. INTRODUCTION The use of surface active agents in flood water to increase the recovery of oil has been studied in the laboratory and in the field for decades, with rather limited success. In recent years a new approach to the problem was proposed. Instead of using an aqueous solution of surfactant as an oil recovery agent, Bond and Holbrook2 proposed that the oil recovery agent be a mixture of surfactant solution and gas. In their method, a water-soluble surface active agent with foam-producing characteristics is injected into an underground formation as an aqueous slug. This slug is followed by gas to produce a foam within the rock. Foams are defined as "agglomerations of gas bubbles separated from each other by thin liquid films'! A foam is fundamentally an unstable system. The foam process for oil recovery has since been studied by other investigators. Fried 1 has shown that foam can displace from porous structures oil that normally is unrecoverable by conventional water or gas drives. This superior oil displacing action is believed to be the result of several factors: (1) foam introduces into the reservoir many resilient interfaces of various sizes and curvatures, which increase the probability that a proper combination of forces for oil displacement will be created; (2) foam has appreciable viscosity which improves mobility ratio and contact efficiency; (3) foam accentuates the trapped gas effect because high gas saturations are possible without producing high gas/oil ratios. Deming4 studied the effect of various foam properties on the displacement of liquid. He found that (1) high foaming ability favors high displacement efficiency; (2) high foam stability is not necessary for high displacement efficiency; (3) displacement efficiency decreases with increase in plasticity of foam and (4) displacement efficiency is unaffected by surface tension of foaming agent solution. One of the important aspects of this oil recovery process is the effect of foam on gas permeability. The simultaneous flow of gas and liquid in porous media has been studied by numerous investigators and a large amount of literature exists on the subject. In this previous work, gas and liquid have generally been considered as essentially independent phases, whose flow characteristics are related through the saturation parameter. Foam, however, is a material with properties that are considerably different from those of its components; for example, the viscosity of a foam is greater than either of its components. Gas flow in a porous medium in the presence of foam should be considerably different

Jan 1, 1965

By James Boyd

Scientists and engineers must concern themselves not only with technical problems, but with the socio-economic difficulties of our scciety. The author states that raw materials are basic to the economic process and that mineral raw materials occur naturally in nearly limitless quantities. He feels that the economic pocess will provide sufficient raw materials for man's needs, and discusses in some detail the world economic environment. As our society grows in complexity, it becomes more urgently incumbent upon scientists and engineers to bring their experiences to bear on the solution, not only of technical problems, but also on socio-economic difficulties. It is to this field that I have directed a large part of my energies. RAW MATERIALS BASIC TO THE ECONOMIC PROCESS There are certain premises, frequently overlooked, which bear emphasis. As economics concerns the production, distribution, and consumption of goods, so our whole society is based on raw materials. Without the basic extractive industries of agriculture and mining, there would be no economic problems with which to deal. This principle has been expressed as "All productivity is based on three factors: 1) natural resources, whose form, place, and condition are changed by the expenditure of 2) human energy (both muscular and mental), with the aid of 3) tools.77* It seems strange that such an obvious statement needs to be made. It is forgotten by all of us, however, at one time or another when we get involved in the complicated theories of economics dealing with the financial and fiscal policies of the various governments, in the financing of enterprises, in marketing, and in labor relations. Unless decisions in all of these fields are made with this, and the rest of the "Ten Pillars of Economic Wisdom," consciously in mind, the resultant policies are doomed to eventual failure, whether these are policies of individuals, companies, or governments. The economic process is basic to society. But economics and the social aspects of humanity are inevitably intertwined. If human needs are not provided for within the basic economic structure, conflicts arise to disrupt the most carefully laid social plans. Similarly, it is the failure of society to cope with basic economic prerequisites that leads to discord within the body politic and thus to eventual economic disaster. We who are engaged in the various aspects of the mineral industry, therefore, have a large part to play in society's future development. MINERAL RAW MATERIALS OCCUR NATURALLY IN NEARLY LIMITLESS QUANTITIES Throughout my career in and out of government, I have formed my decisions on two principles: 1) Fundamentally, all mineral raw materials exist within the earth's crust in quantities greatly exceeding man's needs; 2) Any problems of supply of these materials are primarily economic in nature. With respect to my first assumption, analyses by geochemists enable them to estimate the quantities in which each of the known elements exist in the earth's crust. One of the most cautious and famous suggests that the average copper content of the lithosphere to a depth of ten miles is about 55 ppm. If this is valid, then the lithosphere contains about 1.4 quadrillion (1.4 x 10 ") tons of copper metal — an unimaginable quantity. This is 8,500,000-fold that which has been consumed by man in his existence. To illustrate further, consider that the deepest copper mine in history went to about 9000 ft below the surface; the present copper mines of the world now average less than 1500 ft in depth. We can assume that in most continental land areas of the world it is technically feasible to mine to a depth of at least one mile. The land areas of the world to an average depth of one mile, then, contain 343 billion tons (343 x 10') of copper metal, or 2000 times that which has been extracted to date. I don't believe man will ever expend his energies to extract copper from rocks which contain only a few parts per million, but he knows that each element

Jan 1, 1968

By J. Lohrenz, C. R. Clark, B. G. Bray

Procedures to calculate the viscosities of in situ reservoir gases and liquids from their composition have been developed and evaluated. Given a composition expressed in methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide together with the molecular weight and specific gravity of the heptanes-plus fraction, the procedures are capable of calculating the viscosity of the gas or liquid at the desired temperature and pressure. The procedure for reservoir liquids was developed using the residual viscosity concept and the theory of corresponding states, and was evaluated by comparing experimental and calculated results for 260 different reservoir oils ranging from black to highly volatile. The average absolute deviation was 16 per cent. This is the first known procedure for calculating the viscosity of reservoir liquids from their compositions as normally available, i.e., including the heptanes-plus fraction. The procedure for reservoir gases uses a sequence of previously published correlations. Evaluation of the procedure was accomplished by comparison of 300 calculated and experimental viscosities for high-pressure gar mixtures in the literature. The average absolute deviation was 4 per cent. The calculations are useful for (I) determining viscosities in compositional material balance computations and (2) predicting the viscosity decrease which occurs when gases, LPG, or carbon dioxide dissolve in reservoir oils. INTRODUCTION Methods to predict viscosities of reservoir fluids from the normally available field-measured variables have been presented. Beal,1 Standing,2 and Chew and Connally3 orrelated oil viscosities with temperature, pressure, oil gravity and gas-oil ratio. Carr, Kobayashi, and Burrows4 and Katz et al.5 have presented correlations for reservoir gas viscosities as a function of temperature, pressure and gas gravity. Lie all intensive physical properties, viscosity is completely described by the following function: Eq. 1 simply states that viscosity is a function of pressure, temperature and composition. These previous correlations1- hay be viewed as modifications of Eq. 1, wherein one assumes more simple functions may be used. The assumptions are practical, because the composition is frequently not known. Further, the assumptions are sufficiently valid so that these correlations are frequently used for reservoir engineering computations. In compositional material balance"' computations, the compositions of the reservoir gases and oils are known. The calculation of the viscosities of these fluids using this composition information is required for a true and complete compositional material balance. For reservoir gases, Carr, Kobayashi and Burrows4 have presented a suitable compositional correlation. For reservoir oils, no correlation is available, and data from reservoir fluid analyses have been used7-9 for compositional material balance calculations.* From a theoretical point of view, this is entirely invalid. The reservoir fluid analysis, whether flash, differential, or other process, does not duplicate the compositions which occur during the actual reservoir depletion process, therefore the viscosities measured during reservoir fluid analysis are not those which occur in the reservoir. From a practical point of view, the "error" of using viscosities from reservoir fluid analysis is of varying and unknown significance. One can say qualitatively that the error is greatest where compositional effects are greatest, i.e., for volatile oil and gas condensate reservoirs and pressure maintenance operations. The first requirement to obtain a quantitative estimate of the significance of the error is to develop a reliable compositional correlation for the viscmities of reservoir oils. No such correlation has been available. Consistent with this requirement, the objective of this study was to develop a procedure to predict the viscosity of reservoir fluids from their compositions. Normally, the compositions of reservoir fluids are available expressed as mole fractions of hydrogen sulfide, nitrogen, carbon dioxide and the hydrocarbons methane through the heptane-plus fraction, with the average molecular weight and specific gravity of the latter. The final correlation was to use the composition in this form. While the more challenging objective of the study was the development of a correlation for the viscosities of reservoir oils, the viscosities of reservoir gases were also studied. The end result of the study was a procedure to calculate the viscosities of reservoir gases and liquids suitable

Jan 1, 1965

ARTICLE I Name and Object Sec. 1. This Division shall be known as the Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers. Sec. 2. The object of the Division shall be to furnish a medium of cooperation between those interested in the field of physical metallurgy; that is, the nature, structure, alloying, fabrication, heat treatment, properties and uses of metals; to represent the AIME insofar as physical metallurgy is concerned, within the rights given in AIME Bylaw, Article XI, Sec. 2, and not inconsistent with the Constitution and Bylaws of the AIME; to hold meetings for the discussion of physical metallurgy; to stimulate the writing, publication, presentation and discussion of papers of high quality on physical metallurgy; to accept or reject papers for presentation before meetings of the Division. ARTICLE II Members Sec. 1. Any member of the AIME of any class and in good standing may become a member of this Division upon registering in writing a desire to do so, but without additional dues. Sec. 2. Any member not in good standing in the AIME shall forfeit his privileges in the Division. ARTICLE III Funds Sec. 1. The expenditure of the funds received by the Division shall be authorized by the Executive Committee of the Division. ARTICLE IV Meetings Sec. 1. The Division shall meet at the same time and place as the annual meeting of the AIME, and at such other times and places as may be determined by the Executive Committee subject to the approval of the Board of Directors of the AIME. Sec. 2. The annual business meeting shall be held within a few days before or after the annual business meeting of the AIME. Sec. 3. At a meeting of the Division, for which notice has been sent to the members of the Division through the regular mail or by publication in the Journal of Metals at least one month in advance, a business meeting may be convened by order of the Executive Committee and any routine business transacted not inconsistent with these Bylaws or with the Constitution or Bylaws of the AIME. Sec. 4. For the transaction of business, the presence of a quorum of not less than 25 members of the Division shall be necessary. ARTICLE V Officers and Government Sec. 1. The officers of the Division shall consist of a Chairman, a Senior Vice-Chairman, a Vice-Chair -man, a Secretary and a Treasurer. The office of Secretary and Treasurer may be combined in one person, if desired by the Executive Committee. Sec. 2. The government of the affairs of the Division shall rest in an Executive Committee, insofar as is consistent with the Bylaws of the Division and the Constitution and Bylaws of the AIME. Sec. 3. The Executive Committee shall consist of the Chairman, Senior Vice-Chairman, Vice-Chairman, past Chairman, Secretary, and nine members, all of whom shall be nominated and elected as provided hereafter in Article VII. Sec. 4. The Chairman, Senior Vice-Chairman and Vice-Chairman shall serve for one year each, or until their successors are elected. Each member of the Executive Committee shall serve three years. The Chairman shall remain a voting member of the Executive Committee for one year after his term as Chairman. Sec. 5. The Treasurer of the Division shall be invited to meet with the Executive Committee, but without ex-officio right to vote. He shall be appointed annually by the Executive Committee, from the membership of the Executive Committee or otherwise. Sec. 6. The annual term of office for officers of the Division shall start at the close of the Annual Meeting of the Institute and shall terminate at the close of the next Annual Meeting. ARTICLE VI Committees Sec. 1. There shall be standing committees as follows: Programs Committee. Finance Committee, Membership Committee, Annual Lecture Committee, Technical Publications Committee, Mathewson Gold Medal Committee, Nominating Committee, Education Committee and such other Committees as the Executive Committee may authorize. Sec. 2. It shall be the duty of the Programs Committee to secure the presentation of papers of appropriate character at meetings of the Division. Sec. 3. It shall be the duty of the Finance Committee to inquire into and examine the financial condition of the Division and to consider proper means of increasing its revenue and limiting its expenses. The Finance Committee shall audit the accounts of the Division and report to the Executive Committee prior to the Annual Meeting of the Division. It shall render a budget to the Executive Committee estimating receipts and expenses for the ensuing year so that action can be taken on same at the first meeting following the Annual Meeting.

Jan 1, 1953

By W. G. Lidman, H. J. Hamjian

' I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:' the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F') at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.' Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

By C. F. Allen, G. B. Walker

K. F. TROMP*—In dealing with the question of the most suitable kind of solid media for heavy density suspension processes Walker and Allen point out that the particle size of the solid media should not be taken too fine, as the viscosity increases with the area of the solid media and a low viscosity is essential lor high tonnage and accurate separation. A coarser particle size of the solid media will, in their opinion, of necessity give rise to a differential density in the bath (higher gravity at the bottom of the bath than at the top) but they advocate acceptance of the differential density rather than a higher viscosity. Though I fully agree with the choice the authors have made, I cannot subscribe to their view that only by accepting a differential density in the bath a coarse particle size of the solid media can be used. There certainly is another alternative: stronger agitation. Applying sufficiently strong vertical currents, a uniform gravity can be obtained quite well in a suspension of a coarse solid media. Of course, this is not a very attractive solution, for it means a degradation of the true gravity separation and a step backwards to hydraulic classification, which makes the washing dependent on size and shape of the particles. However, to a greater or lesser extent, this is what actually takes place in all the heavy density suspension processes relying on a uniform gravity in the bath. The so-called "stable" suspension processes make no exception. They all "stabilize" their suspensions by introducing or creating vertical currents, be it upwards or downwards or both, be it by hydraulic or by mechanical means. In fact, there is no such thing as a "stable" suspension in gravity separation, as the very reason for the use of suspensions in this field is the property that the solid media is able to settle and so facilitate the recovery. I have been enlarging on this point because the characteristics of the various processes can only be well understood and viewed from the same angle (from Bar-voys up to Chance) when the fact is recognized that mechanical or hydraulic agitation is a condition sine qua non for obtaining a uniform density from top to bottom in a suspension. Is a Cone-slraped Vessel Essenlial? Of the two alternatives for getting a low viscosity Walker and Allen have preferred correctly the sacrifice of uniform gravity in the bath instead of increasing further their vertical current arid agitation. The resulting differential density of the bath brings the problem of bow to prevent accumulation of intermediate gravity products in the bath, an accumulation which, if not prevented, would ultimately plug their cone. According to the authors an open-top cone combined with a downdraft current of the bath liquid would he the only suitable way to cope with such suspensions and they assume as a fact that "in any vessel other than a cone, such a differential density could not be tolerated." My experience is quilt: different. In my process, which has been in successful operation for more than a decade, differ-ential density of the suspension is applied ranging from values below 0.1 up to differentials above 0.5, according to the prevailing requirements of the individual plant. In this process, which is charac-terized by the use of horizontal currents in a suspension of differential density, the form of the vessel is of secondary importance and different types are in operation. It so happens that none of these are in the, form of a cone. The fact that 24 washboxes on my process have been installed and 12 others are under construction may constitute sufficient proof against the opinion that only a cone-shaped separator would be suited for differential density separation. Horizontal Currents in Differentia1 Den-sity Sepparation I myself have some doubts as to the suitability of a cone with downdraft for dealing with differential density (or, for that matter, any other washbox relying on vertical currents for removing the intermediate gravity products). It ap-pears to me that it is restricted to feed of small size only and even then with watch-fulness. If we take, for example, a piece of 2 in., the draft necessary to pull such a piece down to a zone wherein the den-sity of the suspension is, say, 0.03 higher, is quite considerable. For a suspension of, say, 1.6 sp gr the downdraft will have to be in the region of 3 in. per second. Unfortunately. most of the differential in density is in the part immediately below the reach of the top current which transports the floats. Consequently, we need the downdraft where we like it least: in the upper part of the cone. This entails the risk that light float particles are carried away with the downward current. This current of, say again, 3 in. per second would carry particles up to 1.3 sp gr and 3/8 in. size into the 1.6 gravity zone. This is prohibitive. It is also prohibitive because a downdraft of 3 in. per second in the upper part of the cone would require a tremendous circulation of medium. IIalf way up a 20 ft diam cone, a downdraft of 3 in. per second would correspond with 8500 gpm. With the downward current following the way of least resistance, the strength of the downdraft will not be exactly the same at different places of a cross area. If, as I anticipate, the center of the cone is favored, the strength of the downdraft will fall below the critical value near the

Jan 1, 1950

By K. G. Kreider, J. H. Brophy, J. Wulff

The technology of nickel-activated sintering of tungsten powder has been successfully applied to the densification of plasma-sprayed tungsten. Nickel was added by infiltration in a zinc solution followed by evaporation of the solvent. After sintering one hour at 1300°C density 95 pct of theoretical and transverse rupture strength of 74,000 psi were obtained. Shrinkage was found to be anisotropic and the mechanism of densification was comparable to that found in the nickel-activated sintering of tungsten powder. 1 HE use of a plasma spray gun for the fabrication of massive tungsten parts has become increasingly interesting. Applications now exist where a deposit in the as-sprayed condition is satisfactory. However, these deposits are generally characterized by a lamellar anisotropic microstructure containing 15 pct porosity of which, typically, two-thirds is open to the surface. Mechanically, the as-sprayed deposits fail at relatively low stress levels with a biscuit-like fracture. As a result of these problems the possibility of improving structure and strength by sintering treatments subsequent to spraying is particularly attractive. Preferably this sintering treatment should be adaptable to large bodies of sprayed metal. The similarity between the as-sprayed tungsten structure and that of a powder compact suggests that the relatively low-temperature activated sintering technique1 might be profitably employed in the densification of plasma-sprayed tungsten. It was the purpose of the present investigation to develop a technique for introducing the nickel-activating agent into the sprayed structure, to evaluate the amount and mechanism of densification obtained as a function of time and temperature, and to obtain an indication of the relative strength before and after sintering. EXPERIMENTAL PROCEDURE Powder used for spraying was purchased from the Wah Chang Corp. in several size fractions ranging from an average size of 4 to 150 . These powders were sized further for an explicit study of the influence of average feed size on densification. All powders were dried at 200°C before use. Spraying was accomplished with a Plasma Flame unit manufactured by Thermal Dynamics Corp. Several modifications of the unit were helpful in conducting the investigation. A variable speed auger feed mechanism coupled with the carrier gas mecha nism facilitated the use of fine particle sizes. A coil of ten turns of copper tubing in series with the arc power and concentrically would around the nozzle improved nozzle life and extended the range of operating currents available. The function of the auxiliary coil was to cause the arc to spin and to prevent impingement at only one point in the nozzle. Normally air sprayed deposits were made with an arc maintained at 400 amp at 50 to 70 v. The arc was blown by a gas mixture containing from 5 pct H, 95 pct N for the finest powder feed sizes ranging to 20 pct H, 80 pct N for the coarsest size. The flow rate was maintained at 100 cu ft per hr NTP through a nozzle of 0.25 in. ID. When apraying in air, the powder stream was directed toward an aluminum substrate for ease of mechanical removal of the deposit. The substrate was cooled by diverting the plasma flame with an air jet, and a second jet was directed on the deposit surface. In this configuration a gun-to-work distance of 2 to 3 in. was found to be satisfactory. Fig. 1 represents a typical as-sprayed deposit micro-structure. Laboratory studies of protective atmosphere spraying were carried out in cylindrical chamber 8 in. in diam by 18 in. in length. In operating the nozzle attached to such a chamber, particular care was required to avoid nozzle burn out due to reduced gas flow. The structure and density of the chamber sprayed deposits varied over wide ranges depending on substrate temperature. For the purposes of this investigation, flat deposits were made approximately 2 in. sq by 3/8 in. thick. From these deposits individual samples were cut an ground to a rectangular shape typically 1 1/2 in. by 1/8 in. sq such that the long dimension was perpendicular to the spraying direction. For the study of shrinkage anisotropy deposits up to one inch thick were produced. From these, rectangular samples were cut having a longer dimension parallel to the spraying axis. Prior to the addition of activating agent, the samples were deoxidized in hydrogen at 800°C for 20 min. No detectable dimensional or microstructural change was observed after this treatment. The addition of nickel was accomplished by infil-

Jan 1, 1963

By Peter R. Morris

The effecl of preferred orienlation on X-vay dzffvaction measurements of retained austenzte was investigated for four precipitation-hardening staznless steels in sheet form. A method is preserzted for estimating the ervor in measurement associated with a given samplirig direction. The method was used to select an "optimum" sampling direclion in order to minimize errors in measurement due to preferred orientation. hleasuremenls of retained austenite content employing lhe proposed sampling direction are conzpaved to measuretnents enzploying the more commonly used normal direclion for a series of sawzples. THE first application of X-ray diffraction to the measurement of retained austenite in steels is due to Sekito, 1 who employed a photographic technique in which the (111) reflection from a thin strip of gold affixed to a cylindrical sample was employed as a standard. Averbach 2 introduced the "direct comparison" method in which the ratios of observed to calculated random intensity are assumed proportional to the austenite and/or martensite contents. Averbach's work forms the basis of most subsequent X-ray diffraction methods for the determination of retained austenite. Subsequent improvements are due to: Averbach and Cohen,3 who employed a sodium chloride crystal to monochromate cobalt radiation; Averbach et a1.,4 who introduced a bent sodium chloride monochromator; Mager,' who used a bent quartz crystal to monochromate chromium radiation ; Littmam, who first used a geiger counter diffractometer for this purpose; Beu and Beu and Koistinen, 11,12 who studied effects of absorption factor, surface preparation, sample geometry, integrated intensity vs peak height, choice of radiation, monochromator, and filter. The possibility of errors in measured values due to orientation effects was noted by Miller,13 who suggested examination of a surface other than the plane of rolling. Lopata and Kula 14 have developed an experimental technique in which the preferred orientation is measured in each sample. They illustrated the method for a sample containing 42 pct retained austenite. Application of their technique to the 1 to 15 pct range typical for the precipitation-hardening stainless steels does not appear feasible. EXPERIMENTAL PROCEDURE The nominal compositions of the precipitation-hardening stainless steels investigated are listed in Table I. Ingots were solution-treated, hot-rolled to approximately 0.2 in., and reduced to 0.050 in. by a suc- cession of cold rolling and annealing operations. After this treatment the 17-4PH sample was in the marten-sitic condition, while the 17-7PH, PH 14-8Mo, and PH 15-7Mo samples were in the austenitic condition. Samples of 17-7PH and PH 15-7Mo steels in the mar-tensitic condition were obtained by heating to 1750'F for 10 min and holding at -100°F for 8 hr. A sample of PH 14-8Mo steel in the martensitic condition was obtained by heating to 1700°F for 1 hr and holding at -100°F for 8 hr, followed by aging at 950" for 1 hr. POLE FIGURE DETERMINATIONS Samples were thinned to 0.003 to 0.005 in. by etching in a solution containing 250 ml reagent-grade phosphoric acid (85 to 87 pct H3PO4), 250 ml technical-grade hydrogen peroxide (30 to 35 pct H 2 O 2), and 50 to 100 ml reagent-grade hydrochloric acid (37 to 38 pct HCl). The specimens were placed in an "integrating" sample holder which provided a 1-in. oscillation in the plane of the sample. The diffractometer was aligned to measure the intensity diffracted by planes of the particular {hkl} type being studied. The sample was Set for a given latitude angle, a, measured from the plane of the sheet, and diffracted intensity recorded as the longitude angle, 0, measured in the plane of the sheet from the rolling direction, was increased from 0 to 360 deg. After a 360-deg scan of B, a was incremented by 5 deg, and the process repeated. Random standards obtained by spraying suspensions of powdered iron (bcc structure) and nickel (fcc structure) in lacquer were used to correct observed intensities for absorption and geometrical effects. Zirconium-filtered molybdenum radiation was used to determine the transmission regions of the (111) (0to 45 deg), (200) (0 to 60 deg), and (220) (0 to 45 deg) austenite and (110) (0 to 45 deg), (200) (0 to 50 deg), and (211) (0 to 35 deg) martensite pole figures. Vanadium-filtered chromium radiation was used to

Jan 1, 1968

By D. B. Grove

THE heavy media separation process plays an outstanding role in the concentration of 4000 tons of zinc ore per day at the Mascot mill of the American Zinc Co. of Tennessee. Of the total tonnage, 72 pct is treated in the heavy media separation plant to reject 56 pct of the ore as a coarse tailing, which has a ready market. Concentrates from this separation are beneficiated further by jigging and flotation. Approximately 25 pct of the total zinc concentrate production is made in the jig mill. Jig tailings are ground and pumped to the flotation circuit where the balance of the production is made. Fig. 1 shows a generalized flowsheet of the mill.

Jan 8, 1951

By Oscar Johnson

WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel's Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill.

Jan 6, 1954

By D. M. Given

HOW much can the mine operator afford to spend on his coal burning boiler plant? The usual answer is as little as possible and still get the job done. Thus, attention must be focused on the spot where excessive costs are most likely to arise - the materials handling end of the job. Boiler plants consuming less than 30,000 tons of coal annually can be controlled to the point where costs for handling coal and ashes are under $1.00 per ton. There is a wide selection of coal and ash-handling systems that can be used in smaller boiler plants to provide labor savings and convenience required if management is to accept coal as fuel.

Jan 7, 1953

By Horace V. Winchell

The St. Helens mining-district, indicated in sketch-map, Fig. 1, is chiefly in Townships 9 and 10 North, Ranges 5 and 6 East of the Willamette meridian, in Skamania county, Wash. There is no railroad or even a wagon-road at present connecting it with any base of supplies; access is usually by wagon-road for about 50 miles from the town of Castle Rock to Spirit lake, and from that point by pony-trail from 6 to 10 miles farther. History. Nearly 20 years ago two German farmers, totally inexperienced in prospecting, penetrated this region upon a hunting-and fishing-trip. Their attention was drawn to numerous joints and crevices filled with black, glistening tourmaline, and con-

Jan 1, 1913

By H. P. Allen

THE Achotla mill of the Cia. Minera de Peñoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month.

Jan 1, 1937

By Jose M. Sobral

Approximate figures for petroleum production in Argentina for 1929 show an increase of only about 300,000 bbl. over production for 1928. This increase is due to greater yield in the Plaza Huincul and in the Salta regions. Table 1 shows the distribution of production in the various fields of the whole country, using estimates for the later months of the year. The outlook for production remains about the same as in 1928. It is believed that in northern Argentina there are regions that contain oil, but they are yet unexplored. Notable traces of oil at depths between 1280 and 1390 m. have appeared in a 1500-m. boring in Comodoro Rivadavia, but their importance is unknown.

Jan 1, 1930

By James Yancik

The Howe Coal Co. is mining the Oklahoma Lower Hartshorne bed which ranges in seam thickness from 38 to 42 in. and pitches approximately 7° to the northeast. The raw feed to the cleaning plant averages about 20% ash and 1.10% sulfur, being reduced in the cleaning process to 4.8% ash and 0.9% sulfur with a free swelling index of 8 or 8%. This coal rivals the Pocohantas seam in chemistry and coking characteristics but has better fluidity than the Pocohantas seam coal. The coal is presently being prepared for the Japanese steel market in an 85-tph pilot plant designed and constructed by Roberts & Schaefer. The cleaning-plant flowsheet is discussed in detail.

Jan 1, 1972

By H. T. Wyatt, A. S. Baptie

The Ten Section field is approximately 10 miles southwest of Bakers-field, Kern County, Calif. (Fig. 1). There is no surface evidence of the existence of the Ten Section structure, which subsurface exploration has shown to be a gently folded, anticlinal dome. Regionally, this field occurs as a fold in the deeper beds of the gently rolling floor of the San Joaquin Valley. It is on the easterly slope of the valley, its position with relation to the axis of this syncline not having been determined. The field was discovered by Shell Oil Co. with the completion of well Stevens A-l, on June 2, 1936, at a depth of 7888 ft. The location for this

Jan 1, 1938