Search Documents

By Albert J. Phillips

When brasses containing from 61 to 62.5 per cent. copper are very rapidly cooled from temperatures near their melting point to below 0" C., unusual results are obtained. These results are quite unexplainable from a consideration of the old copper-zinc constitutional diagram but they can be satisfactorily explained by means of the diagram revised by Genders and Bailey1 (Fig. 1). Experiments on a 60/40 Brass If an alloy containing 60 per cent. copper is heated to any temperature between approximately 760' C. and its melting point, it will consist entirely of beta. Upon slowly cooling, alpha will start to separate just below 760" C. Since this alpha will contain nearly 65 per cent, copper, the beta will be impoverished by its separation. As the temperature decreases the composition of the separating alpha will approach approximately 61 per cent. and the beta in contact with the alpha will maintain an equilibrium composition approaching 54.5 per cent. copper. If the rate of cooling is extremely slow, especially at the lower temperatures, stable equilibrium will be established by diffusion through the alpha and beta so that eventually 85 per cent. of the alloy will consist of alpha containing 61 per cent. copper, while 15 per cent. will be beta containing 54.5 per cent. copper. With a faster cooling rate diffusion cannot keep apace and the constituents will be cored, the alpha varying from 65 to 61 per cent. copper and the beta from 60 to 54.5 copper. In this case the amount of alpha will be less than 85 per cent. and the beta will be increased correspondingly. The general structure thus obtained is illustrated in Fig. 2. When a more rapid rate of cooling is effected by quenching in water, the alloy is retained largely in the beta form. However, the crystals of beta are usually outlined with dark fringes which at high magnifications are found to be very fine alpha-beta structures almost martensitic in appearance. The separation of this fringe can be greatly suppressed

Jan 1, 1930

By Arthur Notman

(San Francisco Meeting, September, 1915) SACRAMENTO HILL is a mass of granite porphyry intruded along a fault between Paleozoic sediments and pre-Cambrian schists in the Bisbee district, Cochise County, Arizona. The intrusion invaded both walls of the fault to a large extent, and the accompanying extensive mineralization of the Paleozoic limestones is the locus of the great high-grade copper orebodies of the Bisbee mines. Prior to 1909, although the presence of ore in the mass of the hill itself had long been suspected, systematic exploration had not been attempted. A few shallow pits on the surface here and there had disclosed some chalcocite with associated carbonates as stringers in a mass of strongly brecciated, silicified, and iron-stained porphyry. The workings in the surrounding limestones had penetrated the porphyry in a dozen or so places for some distance from the contact but had disclosed no ore. However, the rock had been largely altered to quartz and sericite and very thoroughly impregnated with pyrite and traces of the copper sulphides. A close geological study of the conditions, both surface and underground, strengthened these suspicions, and plans for prospecting the hill were made in 1909. Reference to the accompanying illustrations, Figs. 1 and 2, will give an idea of the general appearance of the surface. The mineralization is more intense in two main zones, one at the west end and the other at the east end of the hill. The outcrop of the hill is elliptical and approximately 3,000 ft. long by 1,400 ft. wide. The Sacramento shaft, which is the main hoisting shaft of the mine and situated at the east end of the hill, as shown by the accompanying map (Fig. 3), offered a convenient base for prospecting that end of the hill, while the workings from the Holbrook shaft offered a similar opportunity at the west end. The choice of level for the first work was determined by analogy with the most favorable depth for enrichment below surface observed in the other disseminated deposits of the Southwest.

Jan 8, 1915

By Reuben B. Ellestad, Fremont F. Clarke

In the early days of the lithium industry most of the production was from lepidolite, zinnwaldite, and amblygonite. Nearly all the early extraction processes described in the literature involve heating the finely ground mineral with sulphuric or hydrochloric acid. On subsequent water leaching most of the bases present in the mineral (especially aluminum) are dissolved as sulphates. As a result, the leach solution required extensive chemical purification before the lithium could be precipitated as carbonate. Following the remarkable growth of the lithium industry to its present size, zinnwaldite and amblygonite ores must be considered of minor importance only. Attention is now focused on spodumene, abundant enough in North America to be a major source of supply, and there are important supplies of lepidolite and petalite in Africa. The extraction processes described below all apply to spodumene, although several will also operate on other lithium minerals, such as petalite. Base Exchange with Alkali Sulphates: A distinct advance was made with the disclosures of Wadman and von Girsewalt. In these methods the finely ground silicate ore (spodumene or lepidolite) is intimately mixed with an excess of alkali sulphate (usually K2S04) in at least a 1 to 1 proportion, and the mixture was heated to a relatively high temperature. Base exchange results, with the formation of lithium sulphate. A water leach dissolves the lithium sulphate, together with the excess potassium sulphate. Successful operation of this type of process requires very thorough grinding and mixing, as well as careful temperature control. The use of K,SO, is objectionable from cost considerations since purification of lithium carbonate re- quires the use of potassium carbonate, if the K2S04 is to be recovered and recycled. The lower solubility of K,SO, as compared with Na,SO, is also objectionable, since it limits the concentration of the Li,SO, solution to be precipitated by K,CO,. Early laboratory-scale investigation of this process by Lithium Corp. was not encouraging

Nov 1, 1955

By J. J. Egan, A. B. Kinzel

Much work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it constitutes the main action in the usual steelmaking processes. A. L. Feild' has formulated a basic differential equation expressing the open-hearth reactions and Herty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action to the reaction FeO + C + CO + Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Beild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X lop2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order-to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By A. S. Yue

The interface morphology of the Mg-32 wt pct A1 eutectic has been studied in terms of the freezing rate, the temperature gradient, and the impurity content. For the impure eutectic it has been found that for a given temperature gradient a fast freezing rate favors the formation of a cellular intwface with sub-grain strucfure. This cellular interface can be changed to a planar interface of the same substructure either by decreasing the freezing rate or by increasing the temperature gradient. For the eutectic of highest purity, as purified by zme-refining, no cellular interface was found for any growth condition and only a planar interface with subgrain structure was observed. Furthermore, a layer of liquid adhering to the interface during de-cantation freezes with shapes and sizes of the phase particles different from those in the main eutectic solid. WHEN a molten metal or a binary eutectic liquid with zero freezing range is solidified unidirec-tionally, a cellular interface is usually formed-3 This interface is schematically represented by Fig. 1. The profile of the solid-liquid interface has a corrugated shape, as shown in Fig. l(a), while the decanted interface consists of cells, as shown in Fig. l(b). The cell boundary in a frozen eutectic is distinguishable from the cell interior by changes in particle shapes, as shown in Fig. 4. The formation of a cellular interface, according to Weart and ack,' is attributed to a layer of constitutionally supercooled" liquid generated at the advancing interface by the simultaneous rejection of an impurity by the two phases of the eutectic mixture, which then permits freezing over an appreciable temperature range. This concept has been further elaborated by Tiller, who predicts that even in the absence of an impurity the rejection of solute ahead of each lamella of the eutectic may promote the formation of a cellular interface. More recently, Chilton and Winegard, and

Jan 1, 1963

By A. S. Koster, G. D. Rieck

X-ray experiments were carried out to show the occurrence of cylindrical texture in drawn tungsten wire. Only a small amount of (110) (110) cylindrical texture could he found in wires of intermediate thickness, i.e., of about 1.5 mm diameter. DRAWN wires of tungsten and other bcc metals like iron and molybdenum show a well-established (110) fiber texture. Now it might be conceivable that in drawing radial stresses remove the randomness of the crystallites around the [110} axis, thus giving a fiber texture of higher symmetry. In the resulting so-called cylindrical textures a specified plane normal coincides with the radius of the wire. Several authors discuss the occurrence of cylindrical textures in bcc metals. ~ieck' found no cylindrical texture in drawn tungsten wires of 165 n diameter. Leber~ states that in tungsten wires of 3 mm diameter a cylindrical {100)(110) texture is developed, which is gradually converted to a normal fiber texture by subsequent drawing. He also reported a definite cylindrical texture at the surface of iron wires. Peck and Thomas3 observed a nonuniform mode of deformation of the grains in transverse sections of heavily drawn tungsten and iron wires. According to Bhandary and cullity4 a swaged iron wire has neither a perfect (110) fiber texture nor a perfect {100}(110) cylindrical texture. It is clear that the concept of cylindrical texture in bcc metals still lacks a firm experimental basis. Leber's eviden~e,~ which seems to be the strongest, rests upon qualitative interpretation of photographs. The appearance of the 110 and 200 lines on the photograph of 3-mm wire, however, can be very well attributed5 to a normal ( 110) fiber texture superimposed on random background; our Fig. 1, giving a Debye-Scherrer diagram of etched tungsten wire of 180 p, is free of cylindrical texture according to all authors, but is quite similar to Leber's diagram. It was therefore decided to use a different method of X-ray texture determination on tungsten wires of diameters where cylindrical textures may be expected.

Jan 1, 1965

By E. R. Phelps

A determination of feasibility of a new surface mining project requires a study in orderly fashion through the procedures outlined in Section 2 and the previous two chapters of this section. The information and data collected as described in Chapters 3.1 and 3.2 must be correlated, and the many variables that affect the venture must be reviewed. This review will furnish the mining engineer with the information required to make a preliminary evaluation of estimated profit in the venture. It is at this time that management must make yet another decision whether to drop or continue the project. 3.3-1. Maps. For the purpose of collecting, outlining, and correlating a large portion of the data required for a surface mining feasibility study, maps are essential. A map to a mining engineer is like a sheet of music to a musician, or a blueprint to a designer. It provides a pictorial method of presenting mining information not only for practical application in estimating and planning, but also for demonstration of physical relationships to those charged with decision-making responsibilities. GENERAL AREA MAP. The first step in the process of graphic information assembly is the preparation of a "small scale" general area map. Such a map may cover a mining district, a market area, a watershed area or district, or the whole or a section of a geologic feature such as an iron formation or coal seam. An example of such a general area map is shown in Fig. 3.3-la which outlines the various coal mining areas in the vicinity of a proposed "mine-mouth" power station, the Liddell Power Station Project. If Quadrangle Maps of the United States Geological Survey, or their equivalent, are available for an area, a common and very effective technique is to superimpose mining data on these maps, either directly or by means of transparent overlays. Valuable topographic information

Jan 1, 1968

By A. W. Farenwald

Fine grinding cannot be accomplished in machines in which the component parts move in definite and restricted paths with respect to each other. Such machines are crushers. A "grinding mill" may be defined as any machine in which the crushing elements are free to make direct contact with each other but are kept from doing so by the sand to be crushed. Such a machine must possess the ability to give numerous contacts per unit of time. Upon consideration, one will see that this definition nearly includes the old Chilean and Huntington mills, the "rolls" and the stamp mill. It definitely includes all forms of ball, pebble and rod mills. The ideal (perfeet) grinding mill may be defined as one in which the crushing elements are identical in shape and substance and possess perfect freedom of motion with respect to one another. Of the mills mentioned, only the ball and pebble mills come under this definition of the ideal mill. Even the rod mill fails to get a place under this definition of the perfect mill. Modern Fine-grinding Mill In current practice fine grinding is performed in rotating cylinders1 partially loaded with hard objects, the agitation of which accomplishes the crushing or grinding of the rock or ore. The hard objects called "grinding media" nearly always are steel or some other alloy of iron. Hard rock (flint pebbles) have been and still are used to a limited extent. When steel is used as the grinding substance, the form is the sphere or "ball." The combination of rotating cylinder and steel-ball grinding media is termed "ball mill." Shapes other than the sphere have been tried. Cylindrical grinding media also have been and are now used in grinding mills. When cylindrical media are used the mill is termed "rod mill." Mechanical Elements of Grinding Mills The mechanical elements of a grinding mill arc: (1) the rotating element, (2) the grinding media, (3) the rotating means.

Jan 1, 1935

By George Stanley Scott

Many requests for information as to the possibility of washing coals to some predetermined percentage of ash or sulfur have suggested that the producers aim to satisfy some degree of purity set by the user of the fuel, rather than to attain the greatest economic benefit to all concerned. This paper is written to show that the highest economic purity of washed coal can be determined from washability studies of the raw coal, costs of mining and washing coal, and data on the effect of ash and sulfur on the value of the coal for the particular use for which it is intended. Coke fob Blast-fuenace Use For purposes of illustration, we take the case of coal washed for coke to be used in the iron blast furnace. The method outlined can be made general in its application by substituting for the figures used here the actual operating figures for the particular case under consideration. In general, it costs the blast-furnace operation from 8 to 25 c. per ton of pig iron to slag out each 1 per cent. of ash introduced into the blast furnace by the coke. This figure depends on which one per cent. of ash is removed, and decreases with decrease in ash. When blast furnaces and coal mines are considered as a whole, the figure decreases to zero and then becomes negative, on account of low recovery of washed coal. Various figures1 have been given by different investigators. These figures necessarily differ, not only on account of the differences in operating costs but on account of the difference in the respective fuels as well. For the purpose of this paper, which, as explained, is to point out a method of attacking a certain problem, the figures used in the exposition of the method are of secondary importance. It is apparent that no universally applicable figures can be used, because there are none. Each plant has its own coal,2 its own operating cost, and its own conditions.

Jan 1, 1930

By S. P. Burke

OUTBURSTS in coal mines have contributed greatly to the hazard of mining operations in localities in which they occur. They have been responsible for many casualties and fatalities and much property damage. An excellent review and symposium on the subject appeared recently1. From a study of the papers included in this symposium, and other litera-ture on this subject2, the following conclusions or statements seem justified: 1. Outbursts are more likely to occur in deep mines; that is, where the coal seam being mined has considerable overburden. 2. Outbursts usually occur when hard, dense, nonfractured coal is being mined. It is believed that in most cases a fault or a pocket of friable or soft or pulverized coal existed some distance behind the dense coal at the time of the outburst. 3. The outburst involves a rending or pushing of the solid material of the coal face, the roof, or the floor outwards and often is accompanied by the discharge of large quantities of very fine coal. 4. Drill holes or borings into the coal ahead of the workings have failed to yield information either from evidence of increased gas pressure or increased gas flow that makes possible the prediction of outbursts. 5. Mines in which outbursts occur are usually considered "nongassy," or only very slightly "gassy"; yet large volumes of gas may be produced at the time of the outburst. Despite the varied conditions and varied locations in which outbursts have occurred, the foregoing general statements appear to be applicable in whole or in part to all the recorded cases. These observations there-fore should be significant and any explanation of the mechanism of the phenomena should be consistent with them. The following suggestion seems to be in accord with this requirement, and is offered in the hope that it may assist in the further elucidation of this phenomenon.

Jan 1, 1935

By John Griffen

THE distinguishing principle of the Tromp process is the use of a medium in the bath which is not stable, i.e., the solids will settle and the density of the medium increases with depth. A medium of uniform density can most easily be effected by agitation or by means which increase the viscosity of the medium. Either of these works against the sharpness of separation of coal from its impurities. The Tromp process grinds the medium solids to relative coarseness, allows them to settle downward in the bath without hindrance, and introduces horizontal currents of medium at intermediate levels between top and bottom of the bath. This prevents any accumulation of particles denser than the upper layer of the medium from which the clean coal is conveyed away or an accumulation of particles lighter than the bottom layer or medium whence the refuse is removed. In a relatively shallow bath making a two-product separation, the intermediate horizontal currents sweep these intermediate gravity materials away to be discharged with the refuse removed by the conveyor. Such a system provides a number of advantages. The gravity of separation can be changed simply by changing the density of the medium without changing particle size of medium solids or other conditions, as would be necessary with a system requiring uniform or stable density throughout the bath. Some installations in Europe separate at 1.40 sp gr on one shift, producing a superclean coal, and on the next shift reclean refuse from dry cleaning units and effect a separation at 1.80 sp gr. Medium solids may be much coarser in size consist, which reduces the viscosity of the medium and promotes its fluidity and in turn the sharpness of separation. Coarser medium solids with a more rapid settling rate are much more easily recoverable from the dilute medium rinsed from the products. The Tromp process is not limited to the use of medium solids having magnetic properties. Instal-

Jan 1, 1953

By John Griffen

THE distinguishing principle of the Tromp process is the use of a medium in the bath which is not stable, i.e., the solids will settle and the density of the medium increases with depth. A medium of uniform density can most easily be effected by agitation or by means which increase the viscosity of the medium. Either of these works against the sharpness of separation of coal from its impurities. The Tromp process grinds the medium solids to relative coarseness, allows them to settle downward in the bath without hindrance, and introduces horizontal currents of medium at intermediate levels between top and bottom of the bath. This prevents any accumulation of particles denser than the upper layer of the medium from which the clean coal is conveyed away or an accumulation of particles lighter than the bottom layer or medium whence the refuse is removed. In a relatively shallow bath making a two-product separation, the intermediate horizontal currents sweep these intermediate gravity materials away to be discharged with the refuse removed by the conveyor. Such a system provides a number of advantages. The gravity of separation can be changed simply by changing the density of the medium without changing particle size of medium solids or other conditions, as would be necessary with a system requiring uniform or stable density throughout the bath. Some installations in Europe separate at 1.40 sp gr on one shift, producing a superclean coal, and on the next shift reclean refuse from dry cleaning units and effect a separation at 1.80 sp gr. Medium solids may be much coarser in size consist, which reduces the viscosity of the medium and promotes its fluidity and in turn the sharpness of separation. Coarser medium solids with a more rapid settling rate are much more easily recoverable from the dilute medium rinsed from the products. The Tromp process is not limited to the use of medium solids having magnetic properties. Instal-

Jan 1, 1952

By J. S. Miller

THIS paper describes the method of mining a steeply pitching anthracite seam on a heavy pitch in the Orchard vein in No. 1 Tunnel of the Lehigh Coal and Navigation Co. The Orchard vein in the Nesquehoning district has a thickness of about 15 ft. on the level of the gangway, which is sufficient thickness for the gangway to be driven full width in coal. Above the gangway, the vein becomes thinner and near the surface is about 8 ft. thick. The coal is of good hard quality and carries a fairly good roof. The pitch of the vein is between 65° and 70°. Usually the breast-and-pillar method has been employed in the mining of the steeply pitching veins in this section. This method produced good results as far as the mining of the breast was concerned but the recovery of the pillar was difficult as to full extraction and expensive as regards costs. To recover these pillars after the breasts were driven, three methods were commonly employed; they were known as the pillar-breast method, pillar-skipping method, and pillar-chute method. The pillar-breast method consisted in putting a battery in one corner of the pillar (Fig. 1), coupling the manways A and B of the two adjacent breasts for two or three lengths ahead of the working face of the pillar being cut, and working the pillar as a breast. This method was used by the more skilled miners of the earlier days but has practically been abandoned. A slight variation of this method is used to some extent. In this case, the pillars are left wider than ordinarily and of sufficient width for the full-width breast to be driven in and a small pillar left on each side of the pillar breast between it and the regular breasts. With the completion of the "pillar breast," the ribs are drilled full of holes, loaded, and fired.

Jan 3, 1925

By S. R. Elliott

THE Spies mine is located in the eastern half of the northwest quarter of section 24-43-35, near the village of Iron River, Mich., and is operated by The Cleveland-Cliffs Iron Co. Speaking generally, the jasper hanging walls of most of the deposits in the Iron River district dip at a steep angle and are exceedingly strong, standing without caving, even after mining has been continued for years and after large excavations have been made. The ore is fairly hard and tough and contains no slippage faces. It occurs in large masses, which are often egg shape, with the smaller end down, and can be mined in, open stopes without the use of timber. The common system employed in the district is the shrinkage stope, or some modification of it. The Spies system was developed to utilize the advantages of the open-stope method and to avoid the disadvantages of the shrinkage stope. The Spies shaft was sunk to such a depth that the bottom, or third level, was in rock at a short distance below the bottom of the orebody, the shape and extent of which had been previously determined by diamond drilling. This is shown in plan and by the ore contours at the first, second, and third levels in Fig. 1, and in section in Figs. 2 to 7. In order to provide the necessary mills and raises, three parallel crosscuts were driven on 25 ft. centers on the bottom level. Drifts on the second and first levels were driven to the orebody and followed the foot wall in a southerly direction to the end of the ore. In crosscut 3, Fig. 1, raises 30, 40, 50, and 60 were carried up on the foot wall and holed into the second level, and were ultimately carried up and holed into the first level. These foot-wall raises carry the pipes and ladders, provide a means of ventilation, and furnish safe communication to all working places in the stope.

Jan 3, 1922

By John Griffen

THE distinguishing principle of the Tromp process is the use of a medium in the bath which is not stable, i.e., the solids will settle and the density of the medium increases with depth. A medium of uniform density can most easily be effected by agitation or by means which increase the viscosity of the medium. Either of these works against the sharpness of separation of coal from its impurities. The Tromp process grinds the medium solids to relative coarseness, allows them to settle downward in the bath without hindrance, and introduces horizontal currents of medium at intermediate levels between top and bottom of the bath. This prevents any accumulation of particles denser than the upper layer of the medium from which the clean coal is conveyed away or an accumulation of particles lighter than the bottom layer or medium whence the refuse is removed. In a relatively shallow bath making a two-product separation, the intermediate horizontal currents sweep these intermediate gravity materials away to be discharged with the refuse removed by the conveyor. Such a system provides a number of advantages. The gravity of separation can be changed simply by changing the density of the medium without changing particle size of medium solids or other conditions, as would be necessary with a system requiring uniform or stable density throughout the bath. Some installations in Europe separate at 1.40 sp gr on one shift, producing a superclean coal, and on the next shift reclean refuse from dry cleaning units and effect a separation at 1.80 sp gr. Medium solids may be much coarser in size consist, which reduces the viscosity of the medium and promotes its fluidity and in turn the sharpness of separation. Coarser medium solids with a more rapid settling rate are much more easily recoverable from the dilute medium rinsed from the products. The Tromp process is not limited to the use of medium solids having magnetic properties. Instal-

Jan 1, 1953

By Frederick Crabtree, A. R. Powell

When Professor Stoek asked for a paper on the above subject, it was too late to prepare by June 1, or near that time, one that would invoive any appreciable amount of experimental work or original research; but the suggestion was made that a review of the literature bearing on the subject might be submitted in good time, and that later this could be supplemented by any experimental data obtained during the summer, if experiments were carried out. In accordance with this suggestion, there are submitted the following notes on references found in the literature of recent years bearing on sulfur in gas. It is to be understood that, in general, these notes express the opinions of the authors whose papers are abstracted, not necessarily the opinions of the abstractors. Very little published information was found bearing directly on producer-gas sulfur, so this has been supplemented, in certain phases of the subject, by references to illuminating gas. Methods of analysis and processes for the elimination of sulfur from the gas are, without much doubt, very closely related in these two products. As in illuminating gas, sulfur is found in producer gas mainly as hydrogen sulfide, mixed with a much smaller and variable quantity of carbon bisu1fide.l The presence of minute quantities of other organic-sulfur compounds has been intimated, but no definite statement is made concerning these. The amount of sulfur present in producer gas is variable and depends on several conditions. The primary factor is the quantity of sulfur in the fuel, but the form in which the sulfur exists, the temperature of the producer, the air-steam ratio, and the efficiency of the scrubbing process are all determining factors. When the coal used contains less than 0.5 per cent. of sulfur, the sulfur in the gas will not exceed the quantity found in the average illuminating gas.2 Sulfur in producer gas may safely run higher than that in coke-oven gas, due to the lower-flame temperature

Jan 1, 1920

By Henry M. Howe

This paper is a discussion of the extremely valuable one of Mathewson and Phillips, The Recrystallization of Cold-Worked Alpha Brass on Annealing,1 which not only gives us a wealth of important data reached with great intelligence, but also shows both uncommon powers of imagination and a perfectly fair spirit. Let me try to analyze some of their results, and to enunciate some of the laws to which these results point. For brevity I refer to them as "The Authors." The page numbers in parentheses refer to their paper. 1. The Visible Aspects of Recrystallization.—Plastic deformation in a single direction, as in cold-rolling, draws the grains out in that direction, that is, inequiaxes them, without destroying their apparent individuality. Each grain seems to endure the drawing out without changing either its volume or its orientation materially, for the etching tint of each grain seems to be as uniform after as before the drawing out, save for the "etch bands,"2 shown in Figs. A to D of the Authors' Plate I. As the drawn-out metal is heated progressively, on reaching a certain "disintegration temperature" these old grains seem to break up, probably into submicroscopic fragments, and this apparent disintegration is followed by a coalescence of these fragments, so that their number decreases and their size increases, till they may become very much coarser than before the drawing out. Ruder3 coarsened the grains of silicon steel in this way till single grains reached an area of 50 cm. (7.75 sq. in.). The deformation itself probably breaks each grain up into many very small fragments, but the fact that each grain continues to have a uniform etching tint different from that of its neighbors indicates that these fragments retain the initial common orientation of the grain. The apparent disintegration which we observe, then, is rather an abandonment of community of orientation for individuality of orientation, by the fragments formed earlier during the deformation. Hence we

Jan 1, 1917

By George Scott

MANY requests for information as to the possibility of washing coals to some predetermined percentage of ash or sulfur have suggested that the producers aim to satisfy some degree of purity set by the user of the fuel, rather than to attain the greatest economic benefit to all concerned. This paper is written to show that the highest economic purity of washed coal can be determined from washability studies of the raw coal, costs of mining and washing coal, and data on the effect of ash and sulphur on the value of the coal for the particular use for which it is intended. COKE FOR BLAST-FURNACE USE For purposes of illustration, we take the case of coal washed for coke to be used in the iron blast furnace. The method outlined can be made general in its application by substituting for the figures used here the actual operating figures for the particular case under consideration. In general, it costs the blast-furnace operation from 8 to 25 c. per ton of pig iron to slag out each 1 per cent. of ash introduced into the blast furnace by the coke. This figure depends on which one per cent. of ash is removed, and decreases with decrease in ash: When blast furnaces and coal mines are considered as a whole, the figure decreases to zero and then becomes negative, on account of low recovery of washed coal. Various figures1 have been given by different investigators: These figures necessarily differ, not only on account of the differences in operating costs but on account of the difference in the respective fuels as well. For the purpose of this paper, which, as explained, is to point out a method of attacking a certain problem, the figures used in the exposition of the method are of secondary importance. It is apparent that no universally applicable figures can be used, because there are none. Each plant has its own coal,2 its own operating cost, and its own conditions.

Jan 1, 1929

By S. Paul Lindau

THREE years ago it was decided by the management to granulate the matte that is produced in the smelter of the St: Joseph Lead Co. at Herculaneum, Mo., thereby doing away with a large amount of labor in handling the matte and in subsequent crushing. On Mar. 1, 1915, the granulator was put in operation and up to Jan. 1, 1916, 18,735 tons had been, granulated. The four blast furnaces have a daily output of about 280 tons of pig lead and 100 tons of matte assaying about 11.0 per cent. Pb. It is expected that projected improvements in roasting methods will eliminate more sulphur from the charge, and cut down the matte-fall, to about one-half of the present figure. The blast furnaces are tapped into movable forehearths or settlers, 6 ft. by 4 ft. by 22 in., the slag overflowing into 27-cu. ft. slag cars which are hauled to the clump by electric locomotives. Previous to the adoption of granulation, the matte was tapped from the forehearths into small slag pots which were dumped after cooling. The matte cakes were broken with sledges, and transported to the crushing plant for fine crushing and screening. Here the matte was reduced to ¼ -in. size before being fed to the roaster bins.. A Wedge and a Holthoff mechanical furnace are used for preroasting before sintering on the Dwight and Lloyd machines. The matte is returned to the furnaces as an iron flux until the .gradually accumulating copper content reaches about 7 per cent., after which it is put aside to be concentrated in a small copper blast furnace, the resultant high-grade matte-being sold. When the matte does not settle readily from the slag, two settling devices are often used, the second one being a large catch-pot, which gathers any matte that may overflow from the forehearth, the slag then overflowing from the catch-pot into the slag cars. When full of matte, the catch-pot is removed, allowed to cool, and the contents broken and crushed.

Jan 10, 1916

By B. E. Thompson, H. B. Fuqua

For a very brief description of the North Texas area, and the general geological features with which it is associated, the reader is referred to the opening paragraph of last year's summary1. A more complete discussion of the structure of the area, together with other interesting data concerning it, has been published recently by the Bureau of Economic Geology at the University of Texas2. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by operators except by counties or arbitrary divisions of counties. The total number of wells drilled in Archer, Wichita and Clay counties also has been subject to some estimate, as many of the shallower holes are not reported. While both routine development in proven or semiproven areas and exploratory drilling during 1935 showed an increase over the year 1934, the discovery of new producing areas of importance did not show improvement over that period. Several extremely local productive spots within semiproven areas were found in Archer, Cooke and Wilbarger counties; and extensions to older producing areas were developed in Archer, Baylor, Cooke, Montague, Wichita and Wilbarger counties. In Archer County, the Grace and Woods No. 1 Archer County (Fee), 4 miles northwest of Archer City, in the Thomas Glass survey, encountered a sand from 2836 to 2845 ft. of Pennsylvanian (lower Canyon) age, which showed an initial yield of 75 bbl. daily. While its production is of negligible importance, it is given special mention in this review because of the fact that it is producing from a new and deeper horizon than has been previously exploited in the county. Little deep development occurred in the district during the year. The Walter Gant No. 2 C. M. Worsham in J. M. Swisher survey, about 14 miles east of Henrietta, in Clay County, was abandoned at 5127 ft. in

Jan 1, 1936