Search Documents

By Earl S. Greiner, Eric R. Jette

The constitution of the iron-silicon alloys containing from 14 to 33.4 weight per cent silicon has been studied by a number of investigators, whose results have been reviewed in a monograph published by the Engineering Foundation1. In these previous researches, the solubility of silicon in iron was determined by thermal, microscopic or magnetic methods and the compound Fe3Si2 was reported to be stable at temperatures from 0 to approximately 1030' C. This paper describes the results of an X-ray investigation of the solubility of silicon in iron and gives data which prove that the Fe3Si2 phase is unstable below 825" C. In order to obtain the present results on the solubility of silicon in iron, the authors have utilized the lattice constants of the alpha-phase iron-silicon alloys given in a previous publication2, and also some additional data which will subsequently be described. Materials and Methods The alloys used in this investigation are listed in Table 1. They were prepared in 30 or 50-gram ingots by melting specially purified silicon and electrolytic or carbonyl iron in alundum crucibles under a pressure of less than 1 mm. of mercury. The purity of the silicon, electrolytic and carbonyl irons has been given by the authors in previous publications2, 5. The ingots were homogenized in vacuo at approximately 1000" C. for at least 96 hr. and then slowly cooled. The homogenized specimens were ground to powder in a hardened steel mortar. This powder was passed through a 150 or 200-mesh screen and sealed in evacuated quartz, Jena or Pyrex glass tubes and heat-treated as noted in the various tables. Specimens 23A, 24B, 33 and 35 and the specimens heated for one month at 700" C. were quenched by quickly removing the tubes from a horizontal tubular furnace and dropping them into water. The other specimens were quenched by means of a drop-quenching device, which has been described previously3.

Jan 1, 1937

By D. A. Elgillani, S. Atak, D. A. Rice, M. C. Fuerstenau, R. B. Bhappu

Quartz and feldspar cannot be floated with sulfonate at any pH; spodumene floats over a narrow acid pH range, while beryl responds moderately over a broad pH range. After wet-grinding in a steel mill, beryl, quartz, and spodumene float well with sulfonate below about pH 7, whereas the improvement in the response of feldspar is not so marked. A mechanism by which iron can be adsorbed on these minerals is presented. Also, the responses of leached, natural, and wet-ground beryl to amine, sulfonate, and oleate flotation are shown and related to the measured zero-points-of-charge of these materials. Earlier work with leached beryl showed that good flotation could be obtained with alkyl aryl sulfonate over a rather wide pH range using a Fagergren flotation cell.' When a similar response was observed with leached quartz, it was decided that unintentional activation was being obtained from the metallic components of the Fagergren cell. To obviate this difficulty, a microflotation cell was designed, and an experimental technique was devised. These have been described elsewhere. Experiments conducted with the small cell showed that leached quartz could not be floated at any pH with any sulfonate addition,3 which is in agreement with the observations of Kraeber and Boppel.4 Similarly, it was also found that leached beryl responded to sulfonate flotation only over a narrow pH range rather than the broad range reported earlier.1 This early work,1 however, revealed the important effect that wet-grinding in a steel mill has on the flotation response of certain silicates. That is, it was found that quartz and especially beryl floated well over an unusually wide pH range after wet-grinding in a steel mill. Microcline, however, floated poorly below pH 4, even though wet-ground under the same conditions. The work of Eigeles6 on adsorption of oleic acid on leached quartz and iron-contaminated quartz at constant pH is in agreement with these flotation data. Other research has shown that ferric iron, added as a salt to the system, functions as an activator in the narrow pH range in which Fe +++ iron hydrolyzes to its hydroxy complexes.3,5 These phenomena indicate that iron functions differently in flotation systems depending on its method of introduction. The object of this paper is to determine the mechanism by which iron is adsorbed on certain minerals, the mechanism of collector adsorption after iron abstraction, and the role that Fe++ and Fe+++ assume in the selective separation of these minerals. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate, mol wt 450,7 pure potassium oleate, and pure dodecylamine were used as collectors. All other chemicals were reagent grade in quality, i.e., n-amyl alcohol as frother; HC1, H2SO4, and KOH for pH adjustment; and ferric chloride as activator. Conductivity water, made by passing distilled water through an ion exchange column, was used in the experimental work. All minerals used in the investigation were hand-picked specimens. Sample Preparation: Each of the minerals was crushed through 8 mesh, and the product was divided into two groups, one to be ground dry and the other wet. Dry grinding was accomplished with an alumina mortar and pestle. The product was dry-screened to 48 x 150 mesh, cleaned magnetically, deslimed in conductivity water, and dried. Preparation of the samples by wet-grinding involved grinding a 200-g charge of the mineral (-8 mesh) at 60% solids with natural water in a mild steel rod mill for four minutes. This charge was then wet-screened immediately with natural water to 48 x 150 mesh, dried, and cleaned magnetically. Some experiments were also conducted with leached beryl and quartz. These products were prepared by leaching the sized sample (48 x 150 mesh) with concentrated HC1 with a percolation technique until no iron could be detected in the leach liquor. Following this step, the sample was rinsed with conductivity

Jan 1, 1967

By Richard J. Fruehan

ThE thermodynamic activities of nickel and chromium in liquid Ni-Cr alloys have not been previously reported. There have been several investigations on the solid alloys.1-3 In the present investigation the activity of chromium in liquid Ni-Cr alloys at 1600° C was determined by the use of the following galvanic cell, The use of galvanic cells employing solid oxide electrolytes for determining the activity of metals in solid alloys was first demonstrated by Rapp and Maak4 on Cu-Ni alloys between 700° and 1000°C. Recently Schwerdtfeger5 tested the performance of the ZrO2(CaO) electrolyte at 1600°C and found it satisfactory for oxygen pressures as low as 10"12 atm. He also demonstrated the use of solid oxide electrolytes for determining the activities in liquid metal systems in measuring the activity of manganese in Fe-Mn alloys at 1500°C. Extensive investigations have been carried out in this laboratory, exploring the oxygen partial pressure lower limit at which ZrO2(CaO) electrolyte can be used satisfactorily in oxygen galvanic cells at 1600°C. In a paper to be published at a later date,9 it is demonstrated conclusively that ZrO2(CaO) exhibits insignificant electronic conductivity at oxygen pressures down to about 3 x 10"13 atm which is lower than the oxygen partial pressure in equilibrium with Cr-Cr2O3 at 1600°C. Therefore, the activity of chromium can be related to the measured reversible electromotive force of the cell in the present investigation since no electronic short circulating will occur. Fig. 1 is a schematic diagram of the cell used. The Cr-Cr2O3 electrode was made of equal weights of chromium and Cr2O3 powders which were mixed and packed into a recrystallized alumina crucible. A Pt-wire lead was embedded into the Cr-Cr2O3 compact to insure good contact. A ZrO2(CaO) crucible, supplied by the Zirconium Corp. of America, contained the Ni-Cr melt equilibrated with solid Cr2O3. The ZrO2(CaO) crucible was placed on the Cr-Cr2O3 electrode and additional Cr-Cr2O3 mixture was packed around it. Contact with the Ni-Cr alloy was made with a Cr2O3 tube, which is a weak electronic conductor. A platinum wire lead was attached to the Cr2O3 tube. The galvanic cell was lowered slowly into the hot zone of the furnace tube in order to avoid too large a thermal shock which could break the ZrO2 (CaO) crucible. The furnace was con- tinuously flushed with purified argon during the experiment. The temperature was measured with a Pt-Pt/10 pet Rh thermocouple and maintained at 1600° ± 5°C. The electromotive force was measured with a recording potentiometer. The furnace was turned off when measurements were being made in order to avoid induction effects and the reversibility of the cell was demonstrated in the usual manner. The electromotive force was measured several times over a period of approximately 1 hr. During that period the electromotive force remained constant within ± 3 pet and did not continuously drift in any one direction. After the experiment the alloys were analyzed for chromium in the usual manner. The measured electromotive forces of the cell at 1600°C, (2912°F), are listed in Table I. The activity of chromium, with solid pure chromium as the reference state, (a), was calculated using Eq. [l], , n F E I, n lna RT- U] where E is the measured electromotive force, F is the Faraday constant, and n is equal to 3, the number of equivalents per mole, (nF/RT = 18.59 volts'1 at 1600°C). The resulting activities are listed in Table I. The activity of chromium relative to pure liquid chromium was also calculated. The free energy of fusion of chromium at 1600° C was calculated using

Jan 1, 1969

By Carl Floe

A NUMBER of proposals have been made for the hydrometallurgical recovery of copper from flotation concentrates, but as yet no process has been developed that has demonstrated an ability to compete with the present smelting methods under ordinary conditions. The treat-ment of copper concentrates by hydrometallurgical methods is in general similar to that used in the present electrolytic zinc process and involves roasting, leaching with H2S04 solution, separation of solutions, control of impurities and electrodeposition. While many of these steps are simpler and more readily carried out for copper than for zinc, a number of inherent difficulties have prevented the general adoption of the process. To compete with smelting, the following problems must still be con-fronted, although many solutions for their have been proposed: (1) con-duction of the roast in such a way that leaching will give an extraction of copper comparable to that obtained by smelting; (2) regulation of the ferric iron content of the solutions during electrolysis; (3) disposal of the excess acid regenerated from the sulphates formed in roasting; (4) eco-nomical recovery of the precious metals from the leach residues. The roasting problem is largely one of preventing the formation of copper ferrites, CuO.Fe2O, and Cu20.Fe2O3, which are quite insoluble in dilute sulphuric acid. These ferrites are apparently formed' to a small extent even at low temperatures and above 650° C. their formation is rapid1. While it is possible to carry out laboratory roasts in such a way that less than 5 per cent of the total copper is present in the insoluble ferrite form, a closer temperature control is required than can readily be obtained in industrial furnaces. The flash" roasting effects and consequent high temperatures that occur as the calcine falls from hearth to hearth in the ordinary multiple-hearth roaster are probably largely responsible for the inevitable formation of some ferrites. The result is that in a commercial plant the extraction of copper would not average more than 90 per cent in a single 10 per cent H2SO4 leach. This is

Jan 1, 1937

By E. E. Carpenter

Believing that the results accomplished in the mill of the Churchill Milling Co., Wonder, Nev., during the fiscal year ended Sept. 30, 1914, will be of interest, I am presenting the more prominent facts and figures showing the progress made in treating this ore with especial reference to tonnage, supplies, costs, and extractions. The mill is situated at Wonder, Nev., in the Wonder mining district, 55 miles east from Fallon, Nev., the nearest railroad point. All supplies are hauled this distance by freight teams, this method of transportation having been found more reliable for continuous service than truclis, the price paid for hauling being slightly under one cent per pound. In this mill are treated the ores of the Nevada Wonder Mining Co. Ore is Unusually Hard The company which tested this ore before the mill was built reported "This ore is an unusually hard, tough, oxidized quartz, carrying a small percentage of high-grade sulphides, containing good values in both gold and silver. None of the rebellious silver minerals appear to occur in appreciable quantities." ... "In regard to the mill tonnage this ore is unusually hard and tough, and a high stamp duty cannot be expected. Using a 20-mesh screen and 1,050-lb. stamps, our best work was three tons per stamp per 24 hours." It is very probable that the ore delivered to the testing plant was harder than the regular mill run has proved to be. However, at present the mine is developed to a depth of 1,000 ft., and still shows hard ore in places at this depth in about the same proportion as on the upper levels from which the test ore came; during this year's work, ore was treated from nearly all levels. Together with this hard ore in the mill feed a considerable proportion appears to be broken down and tending to crumble, thus making an ideal mixture for stamp milling. A small proportion of talc is also noticeable, which sometimes increases in amount to the point where it is very troublesome in the thickeners.

Jan 1, 1916

By G. W. Traer

The distillation of bituminous coals at what is commonly termed low temperature, and the quantities, nature and adaptabilities of the products have been the subject of considerable experimentation, during recent years. Fortunately, the earlier work in this country was done by men whose scientific training qualified them properly to record and interpret the results of their experiments. The work of Prof. Parr, of the University of Illinois, is especially notable in this respect. Prof. Parr's work, added to that of English experimenters, demon-strated-certain things to a degree which is generally regarded as convincing. They have proved that a caking bituminous coal, when subjected to a temperature of not more than 1000" F. (preferably somewhat less) will yield light tar having low specific gravity (about 1.06) and high value; also, that this yield, with a given coal, will depend upon the percentage of hydrocarbons in the coal, the maximum temperature used, and the promptness with which the distillate gases are removed. It is assumed that air is excluded from the retort, and that the coal is subjected to heat for a sufficient time to drive off all of the tarry hydrocarbons. The results attained in the first, or low-temperature stage of the car-bocoal process, recently described by C. T. Malcolmson,1 corroborate these general principles. It is the purpose of the writer to describe other work of a practical nature, directed toward the commercial adaptation of these principles, which was begun nearly two years ago; this investigation was assisted by A. J. Sayers, of the Link-Belt Co., and Carl Scholz. The first step was to draft tentative designs for the handling of the coal and coke so as to produce a coke having a suitable structure for sizing, storage, shipment, and handling, without the necessity of briquetting. Prof. Parr's results had indicated that the rather open-pored volatile coke produced by him had a low ignition point, which would contribute toward easy control of the fire in stoves, house furnaces, fire-boxes, and boilers. It is recognized by those experienced in the marketing of fuels that the hard non-volatile coke from the high-temperature process,

Jan 1, 1920

By Joseph P. Hodgson

In 1880, mining operations were commenced at the Copper Queen mine. The famous Queen ore body, which extended to the surface, was first quarried from a large open cut in the outcrop. The ore body was followed down to the 300 level with the Queen incline, and stoped. This, we believe, marks the introduction of square setting in the Bisbee district, which is still the method most generally used. Orebodies The orebodies in the Copper Queen mine occur in the limestones, and the main portion of the ore has been mined from the Abrigo, Martin, and Escabrosa limestones. mile the orebodies outcrop in the extreme western end of the mine, the general dip is to the east and south, at an angle of about 20°, although this dip is not by any means regular, being, in fact, very irregular locally. The ore is remarkable for its variableness in character, some of it being very soft, requiring a large amount of timber, and other portions consisting of extremely hard sulphides. The orebodies, in general, while remarkable for their continuity, are very irregular, both as to shape and size. The mine having been in operation so many years, and mining having been prosecuted over such a large area, the operations have caused the shrinkage of the overburden, and there is a constant movement, which is shown by large cracks and interstices in the surface rocks, which largely contribute to the very high deadwork or maintenance cost of the mine. It is surprising that for year 1913 it cost almost $400,000 just for the one item of repairs and dead work in this property. Haulage and Hoisting The underground openings have been extended in the neighborhood of 200 miles. The ore hoisting is performed at a centrally located shaft, the Sacramento, to which all the ores from different parts of the mine are conveyed by electric haulage, of which there was slightly over 9 miles in operation in 1913. The hoisting levels at the Sacramento shaft are placed 200 ft. apart, commencing at the 400 level and continuing down to the 1,600 level, the average hoisting distance being 1,000 ft. The

Jan 1, 1915

By Andrew Corry

GEOPHYSICAL investigations based on radioactivity have been applied to the earth's crust for the purpose of discovering bodies rich in radioactive substances, or for the location of solutions with high emanation or radioactive-salt content, or for the detection of oil, which, in virtue of colloidal properties, has strong powers of radioactive absorption. RADIOACTIVE SUBSTANCES Radioactive substances are distributed in all rocks, waters, and gases in the earth's crust in small quantities. Granites and similar acidic rocks are richest in uranium and thorium, two chief radioactive substances; yet the quantities present in such rocks are of the order 10-12g., this concentration being expressed in grams per gram of the whole substance per cubic centimeter. In granites the uranium yields, according to Haddock, 3 X 10-12 g. of radium per gram of rock. In basalts the uranium yields 1.19 X 10-12 g. per gram per cubic centimeter. Of thorium the granites yield -2 X 10-5 g. per gram of rock; the basalts, 0.77 X 10-5 g. per gram. Certain series of alkalis of low atomic weight, like potassium and rubidium, show weak radioactivity; this property has no significance so far for geological research. The uranium is esti-mated indirectly from the electrical properties of one of its derivatives as a -gas (emanation) into which it is transformed. The thorium is expressed directly, though it is measured as a derivative, thorium emana-tion. There is a measure for the gaseous radium emanation, the curie, which is that quantity of radium emanation, or radon, which stands in equilibrium with 1 g. of radium. The concentration of the emanation is the Mache unit corresponding to 3.64 X 10-10 curie per liter. When gases become permeated by alpha, beta, and gamma rays, plus and minus ions are produced in them by the decomposition of neutral gas molecules, and under the influence of an electrical field these ions are given opposite motions. The measurement of the alpha rays and the bisection thicknesses of the beta and gamma rays is a means of analyzing unknown radioactive substances. These rays accompany the disintegration of radioactive substances and arise from "spontaneous internal changes

Jan 1, 1929

By R. F. Mehl, W. Batz, C. Wells

L. S. Darken—It is indeed gratifying to find that the results of the two different methods here reported are in substantial agreement with each other and with the earlier work1 of two of the authors. Dr. R. P. Smith, of our laboratory, has been conducting some experiments at 1000°C to determine the diffusivity of carbon in austenite by a third method— the steady state method. This work, which will soon be reported, is far enough advanced that we can say it is in substantial agreement with that of the present authors. The only disparity which might be considered significant is in the high-carbon region, where we find that the diffusivity rises a little less steeply than indicated in fig. 8. F. E. Harris—The authors have presented an impressive arrangement of data concerning the diffusion of carbon in austenite. Of particular interest is the compilation, table IV, which is repeated in col. B of table V for direct comparison with values (col. A. table V) from a formulation using a single Q value of 31,000 cal as the activation energy for diffusion. This comparatively simple formulation has been used quite successfully in the practical application of calculating the carbon added (or removed) through the face in carburizing and decarburizing experiments, where the face concentrations are held quite constant for known times and temperatures. Literally hundreds of tests have been so checked where the computed and experimental values have varied by less than 5 pct. For higher temperatures, where proper carburizing data are hard to obtain, the diffusion couple is treated as a decarburization of the high-concentration bar and as a carburization of the low-carbon member. The analysis has been limited to a maximum of 1.40 wt pct carbon. The agreement between cols. A and B in table V may be considered fair, if a liberal viewpoint is taken. The use of a diffusion couple has one serious drawback, in that comparatively small amounts of carbon pass through planes of concentration close to those of the initial high-carbon and low-carbon members, and hence small errors become important. In addition to the sensitivity at these high and low concentrations.

Jan 1, 1951

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: 1-maintenance of metallurgical balance, 2-conservation of oxide ore, and 3-mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak-Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pet, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pet of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1952

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 1/4 to M in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles. Because rock salt is an inexpensive commodity, a low-cost process was required. Gravity methods were, of course, considered. The heavy-liquid separations indicated that a split at an effective specific gravity of 2.2 to 2.3 would be required. (The specific gravity of pure halite is 2.16.) Heavy-media separation was investigated but had the disadvantages that it was necessary both to operate with saturated brine and to dry the cleaned salt, and that the cleaned salt was darkened by the magnetite medium. Air tabling was tried but did not give the desired separation. It soon became apparent that established methods would not provide a satisfactory solution and work was undertaken on the development of a new process to solve the problem. PROCESS DEVELOPMENT Preliminary Experiments: At the start of the investigation, an analysis of the problem indicated that the diathermacy of rock salt—that is, its ability to transmit radiant heat—might form the basis for an efficient separation process. Under this theory, the impurities might be selectively heated by radiant heat. The particles could then be fed over a belt coated with a heat-sensitive substance so that the warm impure particles would adhere preferentially to the coating. After the initial experiments, made by heating the rock salt with an infrared lamp and separating the product on small sheets of resin-coated rubber, proved encouraging, a small continuous separation unit was set up. This comprised 1) a simple heating unit consisting of a vibrating feeder covered with aluminum foil and an infrared lamp mounted above the feeder and 2) a separation belt 6 in. wide and 36 in. long. A sketch of the device is shown in Fig. 1. Results with this apparatus confirmed the fact that a good separation was possible. It was apparent, however, that a considerable amount of experimental work would be needed to develop the scheme to a practical and economical process. The Process: Basically, the process consists of two main steps: 1) selective heating by radiation and 2) separation of the heated particles on a heat-sensitive surface. Because neither of these steps had previously been utilized commercially in mineral processing, it was necessary to do basic research on both aspects. Factors studied in the investigation included type of heat source, design of heating unit, design of separation belt, selection of heat-sensitive coating, removal of heated particles from the belt, contact between particles and coating, and maintenance of the heat-sensitive surface. Part of the experimental work was carried out on a small-scale unit consisting of the 36x6 in. belt and auxiliary apparatus, and part on a larger unit. For simplicity, discussion of work on both of these units is grouped together. SELECTIVE HEATING Radiant-Heat Source: The essential requirements for a radiant-heat source were 1) that the radiant heat be in a wave length range which is effectively absorbed by the impurities but not absorbed appreciably by the rock salt and 2) that it be dependable, practical, and economical. Selection of a heat source of suitable wave length range was one of the first considerations. It is well known that pure halite is highly transparent to radiant energy in wave lengths from 0.3 to 13 microns. However, the available data on infrared transmission by dolomite and anhydrite, particularly in the range below two microns, were not complete enough to serve as a reliable basis for selection of a heat source. Although it may have been possible to obtain sufficient data on infrared transmission and absorption to enable one to select the best heat source, a more direct procedure was used. This consisted simply of exposing the crude rock salt to each of several types of radiant-heat source on the small continuous separation device. The heat sources investigated, approximate source temperature used, and calculated wave length of maximum radiation are tabulated in Table I. Of the two types of tungsten-filament lamps investigated, both the short wave length photoflood lamps and the longer wave length infrared lamps were satisfactory from the standpoint of selectivity

Jan 1, 1961

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydrochloric acid and other chemicals has existed and continues. For example, most of the sodium sulphate produced is a byproduct or co-product in the manufacture of hydrochloric acid through the reaction of sodium chloride with sulphuric acid. In recent years, many manufacturers of rayon have installed equipment to recover sodium sulphate from waste spin bath liquors; today this is an important source. Before World War II large quantities of sodium sulphate were imported from Germany. In 1949 imported material from Europe again appeared on the domestic market. Natural sodium sulphate from Canada in substantial quantities also enters the United States markets. Despite this kind of competition, numerous attempts have been made to exploit various natural deposits of sodium sulphate in this country, but only a very few of these have survived economically over a period of years. One of these few operations is the plant of the Ozark-Mahoning Co. located 13 miles south of Monahans in West Texas. Several factors contributing to the successful life of this plant may be summarized as follows: 1—Geographical location. Monahans is reasonably close, freightwise, to the Kraft paper mills in Texas, Arkansas, and Louisiana; the Kraft paper industry is the greatest consumer of sodium sulphate in the United States. 2—Availability of natural gas as low cost fuel. Proximity of the natural gas fields of West Texas has been a tremendous asset, as the availability of low-cost natural gas is to all industry throughout the Southwest. 3—The nature of the deposit. The occurrence of sodium sulphate brines in southeastern New Mexico and West Texas has been very well described by Lang,' who writes that the brines are found in the Castile formation of the Delaware basin. Here weathering has altered the anhydrite so that a relatively porous gypsiferous zone overlies a dense impervious mass of anhydrite. This porous zone provides traps where percolating ground waters that have picked up soluble salts may lodge. These traps or pockets are the natural brine reservoirs exploited at Monahans. Although several hundred wells have been drilled, currently some 25 wells serve to supply brine to the plant. All are within 1 1/2 miles of the plant and are conveniently tied together by an electric power system serving electric motors driving the pumps. Having the raw material in the form of a brine which can be pumped from shallow wells makes possible much simpler and more efficient handling than if it were in form of solids. By contrast, other deposits of sodium sulphate, such as those in Arizona, Nevada, and North Dakota, are in the form of the solid minerals, thenardite and mirabilite, which present somewhat more of a mining and mineral dressing problem.' The largest producer of sodium sulphate from natural sources in the United States is at Searles Lake, Cal., and there a brine also is utilized. 4—Water. Substantial quantities are needed for cooling towers and for operation of gas engines. An area underlain with brine is not a promising source of fresh water, but fortunately, after a long search, an adequate supply was found nearly two miles from the plant. It may be appropriate to discuss briefly the grades of sodium sulphate offered on the market. Salt cake is the name usually applied to the grade of sodium sulphate used by the Kraft paper industry. It may be a low analysis byproduct, 95 to 97 pct sodium sulphate, with as much as l 1/2 to 2 pct residual acid, or it may be a natural product. Usually salt cake is considered a low grade product, but a great deal of a higher grade of material is marketed under this name. The specifications for glassmakers' salt cake are somewhat higher than those of the paper industry, usually requiring 98 pct sodium sulphate. Technical anhydrous sodium sulphate is a high grade material and usually exceeds 99 pct sodium sulphate. It finds the biggest market in the textile industry and is used as a builder in some synthetic detergents. Glauber's salt, Na2SO4. 10H20, is usually of high purity. Preferred for some uses, it normally has been recrystallized from an anhydrous salt. A unique manufacturing process has been developed at Monahans. This process results in the production of an exceptionally high grade of salt cake, and qualifies for nearly all uses, including many which specify the technical anhydrous grade. All of the finished product, which is very white, passes a 10-mesh U. S. Standard screen, and is retained on a 200-mesh U. S. Standard screen. It is over 99 pct Na2SO4 with main impurities being sodium chloride and magnesium sulphate. Iron content is less than 0.01 pct. As mentioned, the raw material at Monahans is a brine drawn from wells. Attention was first attracted to this location because a so-called alkali

Jan 1, 1954

By W. T. Lundy

THE forms in which sulphur is commonly found-native sulphur, sulphides of many metals and sulphates-are widely distributed throughout the world. The two first mentioned are the principal sources of sulphur. Substantial amounts of sulphur in some form are recovered from gases from industrial plants and from gases from smelters treating other minerals. In recent years, plants have been installed in the United States to recover sulphur in elemental form from sour gases."' The amount of sulphur so produced is small at the present time but undoubtedly will increase in the future. The recovery of sulphur from gases is not covered in this chapter, which is confined to: (1) native sulphur deposits of Texas and Louisiana; (2) those of Italy; (3) other scattered deposits of native sulphur; and (4) pyrites deposits found in many countries of the world.30 Sulphur, a nonmetallic element, occurs normally in well developed bipyramidal or tabular crystals of the orthorhombic system, as well as in stalactitic and earthy masses. The mineral has a distinctive yellow color, which may be dark and discolored by impurities; the streak is white; the luster is resinous; and the fracture is conchoidal to uneven. Sulphur is translucent to opaque; has a hardness of 1.5 to 2.5, a specific gravity of 2.05, and an atomic weight of 32.06.16 The molecular weight of the solid is expressed by the symbol SS and that of the liquid and vapor ranges from S2 to S8, depending on the temperature. Sulphur melts at a temperature between 2340 and 248°F, depending on its crystalline state, to a liquid of dark amber color, the boiling point of which is 832°F. The viscosity near the melting point is about that of water and increases to 50,000 times that of water at a temperature of 380°F, subsequently falling rapidly to a low figure at the boiling point. Crystallization changes slowly from rhombic to monoclinic above 205 °F and in cooling the transformation is reversed. The mineral is a very poor conductor of heat and electricity; it is insoluble in water and nearly all acids and is soluble in cold carbon bisulphide and carbon tetrachloride. It ignites in air at a temperature of 478°F, burning with a distinctive blue flame with evolution of sulphur dioxide.47

Jan 1, 1949

By H. D. Kessler, F. A. Crossley, J. J. Rausch

The titanium-rich corner of the system Ti-AI-V has been studied to determine the phase relationships in the temperature interval 600° to 1200°C. Metallographic examination of long time isothermally annealed specimens was the principal method of investigation. TWENTY-SIX alloys in the region 1 to 22 pct A1 and 2 to 11 pct V, and the temperature range 600° to 1200°C, were studied as part of a program on phase relationships and transformation processes of titanium alloy systems. Experimental Procedure Preparation of Alloys—Materials used in the preparation of alloys were high purity Bureau of Mines sponge titanium (103 Bhn), 99.7 pct pure V chips obtained from the Electro Metallurgical Div., union Carbide and Carbon carp., and 99.71 pet pure A1 in the form of granulated shot from Aluminum cO. Of The alloy ingots, weighing l5 g, were melted in a nonconsumable tungsten electrode arc furnace un-

Jan 1, 1957

By Joseph Hartshorne

Ever since the introduction of the Siemens regenerative furnace, it has been recognized that a certain amount of gas is lost each time the furnace-action is reversed. This loss comes, first, from the gas which passes through the free connection between the stack and the gas-main, which exists during the time the reversing-valve is turning over; and, secondly, from the gas which is in the chamber and flues, from the hearth to the reversing-valve, and which flows back into the stack when the valve is reversed. The amount lost each time is, of course, small; but, since a furnace is reversed from four to six times every hour for, say, 300 days in the year, the aggregate is large enough to be well worth attention. The estimate has been published1 that, in Germany aloue, the loss from the first of the above causes amounts to 500,000 barks per year. The loss from the second cause is, of course, much greater.

Jan 1, 1907

By Zay Jeffries

IN this paper, it is proposed to outline a method for the determination of melting points of those metals and alloys having high fusion temperatures. The application of the method as used to determine the melting points of alloys of tungsten and molybdenum will be given. It will be seen from these results that tungsten and molybdenum form a completely FIG. 1.-PARTIAL SECTION OF APPARATUS USED TO DETERMINE MELTING POINTS OF TUNGSTEN AND MOLYBDENUM ALLOYS. isomorphous series. This is also verified by the accompanying photomicrographs. Tungsten and molybdenum have been found to crystallize in the salve system, namely, isometric, and the crystal units are cubes. These determinations were made by examining etching pits in the pure metals.

Jan 7, 1916

By James Magee

THERE is nothing new about drag-line dredging for placer gold. The use of the separate unit for excavating preceded the large barge with excavator mounted upon it, which has reached a high state of perfection through use in every part of the world. But at present there is a vogue for a small, inexpensive plant combining a drag-line excavator on cater-pillar mounting and a gravel-washing plant on a floating barge. The most efficient ones use a bucket of 1 to 2 yd. capacity with boom from 40 to 70 ft. long. The barge varies from 20 by 30 ft. to 36 by 48, and carries the trommel screen, pump, riffle sluices and power engine.

Jan 1, 1936

By Luis Toron, Salvador Cortes-Obregon

THE Oaxaca coal fields, shown in Fig. 1, are located in the Alta Mixteca region in the states of Oaxaca, Puebla, and Guerrero. Known outcrops are scattered over 3125 square miles. It is probable that further exploration will reveal a more extensive area of deposits. The region is of great importance to Mexico, as at present the only sources of coal are the fields near the U. S. border. Steel mills are also located in the North, and finished products must travel 600 to 800 miles to the area of consumption in central Mexico. The oaxaca coal, only 120 miles south of Mexico, D.F., lies close to several iron ore deposits. If this

Jan 1, 1955

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first.

Jan 1, 1929

By Nev A. Gokcen

DISCREPANCIES and scattering in the equilibrium data on the reactions of hydrogen, and CO with dissolved oxygen in liquid iron are un- duly large. Available experimental results on the reduction of liquid ferrous oxide, i.e., wüs-tite, with hydrogen and CO are questionable, as pointed Out by Darken and Gurry'l Direct determinations of the solubility of oxygen in liquid iron are subject to errors which cannot be easily reduced by further experimental refinements, and therefore an accurate but indirect method is highly desirable. The purpose of this investigation was, therefore, 1)

Jan 1, 1957