Search Documents

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By Clarence Zener, Howard Clarke, Cyril Stanley Smith

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.'l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1' to ensure axial application of the load. The rate

Jan 1, 1942

By R. Schuhmann

The expression "unit process " comes up with increasing frequency in discussions among metallurgists and mineral engineers, especially among those concerned with training the next generation. The unit process approach characterizes a significant advance along the road from metallurgy as an empirical art to metallurgy as a branch of engineering. The purposes of this paper are to define and list the unit processes in specific terms, to indicate the scientific and engineering principles basic to all the unit processes, and finally to show how these ideas have been applied to a reorganization of instruction in chemical metallurgy. Unit Operations and Unit Processes Metals are extracted from ores and other raw materials by stepwise procedures. In general, each metallic element is extracted by a different procedure. For many of the metals there is a choice of several flowsheets. However, the procedures all have steps in common. In fact, the many different flowsheets are all made up of a relatively small number of steps which are combined in different groups and sequences. For example, crushing, screening, roasting, sintering, melting, and gaseous reduction are steps which each appear in the Bowsheets for extracting the majority of the metals. The individual steps or flowsheet units can be designated as unit operations or unit processes. These terms are well established in the field of chemical engineering, as the American Institute of Chemical Engineers' definition of chemical engineering shows: " Chemical engineering is that branch of engineering concerned with the development and application of manufacturing processes in which chemical or certain physical changes of materials are involved. These processes may usually be resolved into a coordinated series of unit physical operations and unit chemical processes. The work of the chemical engineer is concerned primarily with the design, construction, and operation of equipment and plants in which these unit operations and processes are applied. Chemistry, physics, and mathematics are the underlying sciences of chemical engineering, and economics its guide in practice."'1a In this definition, the distinction between unit operations and unit processes is that the unit operations are physical while the unit processes are chemical. Table I gives a list of the principal unit operations and unit processes of chemical engineering, taken from Shreve.1b Table 2 lists the principal unit operations and unit processes used for metal extraction. The division between unit operations and unit processes is similar to the chemical engineers' distinction and also correspollds approximately to the division of labor bctween mineral dressing and chemical metallurgy which has been customary in the past. Furthermore, it will be noted that in the proposed classification the unit processes primarily involve chemical reactions and/or changes in state of aggregation; the unit operations primarily do not involve either bulk

Jan 1, 1949

By Howard Clarke, Cyril Stanley Smith, Clarence Zener

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.'l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1' to ensure axial application of the load. The rate

Jan 1, 1942

By B. N. Bose, M. F. Hawk

SINCE Davenport and Bain' introduced the isothermal transformation technique for the study of austenite decomposition in steels, a new field of investigation has opened up. Extensive research has been carried out on many different steels, but relatively little work has been done on eutectoid transformations in analogous alloy systems. The researches of Smith and Lindlief,² Mack,³ and Klier and Grymko²0 on the beta-phase transformation in copper-aluminum alloys, of Hibbard, Eichelrnan, and Saunders4 and Smith5 on the kappa-phase transformation in copper-silicon alloys, of Chaudron and Forester6 on the decomposition of "FeO," and of Wasserman7 on similarities between the iron-carbon, copper-aluminum, copper-tin, and copper-beryllium systems essentially comprise the field. The iron-nitrogen system, in view of its remarkable similarity to the iron-carbon system, is particularly attractive for the study of eutectoid decomposition. The present investigation is concerned with the study of isothermal transformation, proceeding by the familiar nucleation and growth processes, and of martensitic transformation characteristics of pure iron-nitrogen alloys. The kinetics of transformation and the morphology of the transformation products have been investigated, for these must be the factors determining the properties and behavior of the final product. The Iron-Nitrogen System he binary iron-nitrogen phase diagram has been a matter of considerable disagreement among vari01.1s investigators. However, the phase diagram according to Eisenhut and Kaupp8 and Lehrer10 is now considered essentially correct as reproduced in fig. 1. The important values, 2.35 pct nitrogen and 591°C, for the co-ordinates of the eutectoid point (obtained from this diagram and used in the re- search to be described) were confirmed in a concurrent study of Paranjpe, Cohen, Bever and Floe." The eutectoid decomposition involves the transformation of the ? face-centered cubic interstitial solid solution of nitrogen in iron to the a body-centered cubic interstitial solid solution of nitrogen in iron and the ?' nitride of iron. This nitride is essentially the compound Fe,N; it also possesses a face-centered cubic lattice but a considerably larger one than the ?; the nitrogen atoms in ?' are arranged in an ordered way in the centers of the unit cubes.8,10,11 A martensitic structure has also been reported8,12 in iron-nitrogen alloys and was studied in the research to be described here. Materials and Methods The specimens used in this investigation were prepared by nitriding "pure" iron. This iron was supplied by the Westinghouse Research Laboratories and is the product bearing their trade name "Puron"; it contains about 0.04 wt pct total impurities, the major portion of which is oxygen. Specimens were ribbons several inches long, a tenth of an inch wide, and 0.125 mm thick; this was the

Jan 1, 1951

By R. R. Knuckey

HAVING been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout. the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. DESIGN OF SEPARATOR The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed paddle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the paddles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1943

By M. J. Marcinkowski, D. Koskimaki, A. S. Sastri

THIS is the second in a trilogy of investigations carried out in order to understand the solid state transformations and their accompanying effects on the deformation behavior of near-equiatomic Ni-Ti alloys. The first stage of this effort has dealt with the strictly martensitic structures obtainable in these alloys, i.e., those in which diffusion processes were not involved.1,2 These martensites could be produced either by rapid quenching or by plastic deformation of the originally B2 type phase. The present investigation, on the other hand, will deal with those transformations in Ni-Ti which do involve diffusion. A majority of investigators3-10 have shown that the B2 modification of TiNi, which is stable at elevated temperatures, decomposes into one or both of the intermetallic compounds NiTi2 and Ni3Ti below about 650°C. On the other hand, this has been disputed by several Workers was undertaken in order to resolve this discrepancy, as well as to shed more light on the nonmar-tensitic decomposition of B2 NiTi. EXPERIMENTAL PROCEDURE Sample preparation, fabrication, and examination were the same as those described previously in Ref. 2. In addition to the 50 at. pct Ni (55.06 wt pct) hypoeu-tectoid alloy used previously, a second hypereutectoid alloy containing 54.4 at. pct Ni (60 wt pct) was also prepared for this study. RESULTS AND DISCUSSION The equilibrium diagram for the Ni-Ti alloy system in the vicinity of Ni-Ti is shown in Fig. 1. The solid lines have been established by the work of Poole and ~ume-Ftothery4 whereas the dotted lines are based on findings obtained in the present investigation as described below. Structure and Morphology. Fig. 2(a) shows a bright field transmission electron micrograph of a two-phase structure obtained in a polycrystalline Ni-Ti alloy that was furnace cooled (approx 200°C per hr) from 1050' to about 300°C. Large plate-shaped precipitates can be observed in a matrix which was found by electron diffraction to possess the high temperature B2 structure. A selected area diffraction pattern of the region covered by Fig. 2(a) is shown in Fig. 2(b), while Fig. 2(c) is a detailed schematic interpretation of Fig. 2(b). The B2 matrix reflections are illustrated by squares while those of the precipitate are shown as circles. The d values associated with the precipitate reflections could be determined quite accurately since the reflections from the B2 matrix, for which the lattice constant is known precisely, were simultaneously present in the diffraction patterns. All of the reflections

Jan 1, 1970

By Richard Hodgson

FMC Corporation, at their mine and soda ash refinery near Green River, Wyoming, currently mines in excess of 3 million tons per year of trona. Upon completion of the current expansion, the mine will be producing in excess of 4.0 million tons per year. The single level mine, approximately 1,500 feet in depth, is currently serviced by five (5) concrete lined circular shafts varying in diameter from 12 ft. to 24 ft. A sixth shaft is complete, but not yet operational and the seventh is currently being sunk. Two of the shafts are equipped with single drum hoists. The original production shaft is equipped with a double drum hoist. The newest production shaft and the main service shaft are both equipped with ground mounted friction hoists. These friction hoists have given excellent service and another will soon be installed as a man and material hoist at No. 7 Shaft. There are a number of advantages that the ground mounted hoist has over a tower mounted hoist. There are also operating problems common to both. FMC's original experience with ground mounted friction hoists began in 1962 with the conversion of a single drum hoist to a friction hoist. The converted hoist was an Ottumwa with a 5 ft. diameter drum and a 4 ft. face. This hoist had been installed at the No. 3 Shaft for some years prior to its conversion to a friction hoist. At the time the conversion of this hoist was made, there were no friction hoists in service in Wyoming. Wyoming mining laws required that all conveyances carrying men be equipped with safety dogs. Since it was desired that wire rope guides be used, safety dogs were impractical. Agreement was reached with the State Mine Inspectors that safety dogs would not be necessary provided that recommended rope safety factors for hoisting men would still be maintained if one hoisting rope was broken. Since-the shaft is approximately 1,500 ft. deep, the recommended safety factor is 6.0 so that this installation has a safety factor in excess of 8.0 for hoisting men when new ropes have been installed. The hoist conversion was engineered by Lake Shore, Incorporated. The friction ring was made in halves and bolted over the original drum face which had been machined to remove the grooves. The ring provided for four 3/4 in. diameter ropes on 8 inch center to center spacing. The pitch diameter of the modified drum was 72 inches. The grove liners are hald in place by hard-wood wedges bolted to the drum. The other modification required by the conversion was an increase in size of bearing caps and the hold-down bolts because of the increased force tending to lift the drum.

Jan 1, 1975

By William B. Stephenson

IN the pumping of sands, slurries and slimes, practices developed over the years are the real keystones of successful operation. These practices are necessarily based on modifications of familiar theories. Practical methods used in the solution of problems involving the pumping of materials are set forth in the following discussion. BASIC REQUIREMENTS To pump sands and slurries economically, a few basic requirements must be met by the pumping system as a whole. A pipe-line velocity must be established that will move the fluid mixture throughout the entire system without any possibility of the solids settling out. To accomplish this, the velocity of flow must be slightly in excess of the critical velocity of the mixture. The critical velocity of a mixture varies from 3 ft. per sec. to 18 ft. per sec., depending on the screen analysis, concentration, and specific gravity of the solids in the mixture. Most tailings are pumped at a minimum velocity of 4 ft. per sec. if they include slimes, whereas the pipe lines of sand and gravel dredges require velocities as high as 18 ft. per second. A number of articles have been written on the determination of the minimum velocities required to maintain solids in suspension. Studies have also been made on the friction and pumping heads developed when handling solids in suspension.1-4 Our experience so far has shown that, within the normal operating limits of a pumping system, the friction factor follows more nearly the basis described by Howard,1 who says, among his conclusions: " ... values of ƒ (friction factor) .. . will decrease with an increase in velocity." This conclusion is borne out by our actual experience. When the velocity in a pipe line is not sufficient to keep the solids in suspension, the total friction head is greater than when the velocity is increased to a point where the solids are in suspension. A slight increase in the volume of feed to the pump and a slight increase in the pump speed are usually all that is necessary to put the system in balance. MAINTAINING CONSTANT VOLUME Within reasonable limits, the volume of mixture to be handled through a pipe line should be held constant, so that the required velocity will be provided at all times. There are several ways in which this can be accomplished. The commonest is to provide a sump of sufficient capacity to take care of slight surges in the volume of mixture being fed to the pumping system. This sump, however, should not be as large as a settling chamber. The use of a float-controlled, fresh-water make-up valve in a sump will guarantee a constant volume. Where variations in volume are slight,

Jan 1, 1946

By R. E. Zimmerman

THE separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pct successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the -48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of -48-mesh slurries. These large scale operations have been recently described by D. H. Davis. 1 C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investigational work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investigational work as well as the results of experi¬ments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. METHODS OF CONDUCTING LABORATORY TESTS The bulk of the research work was conducted in the laboratory of the Champion No. r Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location

Jan 1, 1948

By A. R. Hendrickson, C. F. Smith

Hydrofluoric-hydrochloric acid mixtures have been successfully used to stimulate sandstone reservoirs for a number of years. Hydrofluoric acid (HF) has a specific reactivity with silica which makes it more effective than HCl for use in sandstone. Kinetics of the reactions of HF have been studied to determine the related effects of reservoir composition, temperature, acid concentration and pressure on the spending rate of HF. Secondary effects from by-product formation are noted and described. Predictions are made concerning the improvement in productivity resulting from HF treatment of skin damage. The kinetic order of HF reaction in sandstone was experimentally determined to be first order, i.e., the reaction rate is proportional to concentration. HF reacts faster on calcite than on clay, which, in turn, is faster than the reaction rate of HF on sand. Static conditions retard the HF reaction rate. As HF is forced into cores, there is a temporary reduction as a function of flow rate and acid concentration. Extensive deposition of calcium fluoride in acidized cores was not observed. Although some CaF, was defected, it was not considered a major source of damage in cores containing moderate amounts of carbonate. Other fluosilicates could be potentially more dangerous than CaF, in reducing permeabiliry. INTRODUCTION Hydrofluoric acid has been widely used in stimulation treatments since 1935, when mud acid was introduced to the petroleum industry. Originally, this hydrochloric-hydrofluoric acid mixture was intended to remove mud filter cake, but it has since been successfully applied to many other oilfield problems. Mud acid treatments have been unusually successful in sandstone reservoirs where hydrochloric acid is unreactive due to a lack of enough calcite in the formation. The relatively small amount of hydrofluoric acid present (2.1 per cent) reacts with sand grains, clays and traces of calcite which are generally present in sandstone reservoirs. Since hydrofluoric acid (HF) is the key to mud acid success, this research effort has been dedicated to gaining a more thorough understanding of the basic chemical and physical principles involved as HF reacts. Hydrofluoric acid's reactivity with silica makes it unique in application. Other mineral acids such as hydrochloric, sulfuric or nitric are unreactive with most silicious materials which comprise sandstone formations. A typical sandstone reservoir may contain 50 to 85 per cent silicon dioxide, more commonly called sand or quartz. Hydrofluoric acid reacts as follows: 4HF + SiO2 + SiFO + 2H2O The silicon tetrafluoride (SiF,) is a soluble gas, in some ways similar to CO2, and is capable of undergoing further reaction when held in solution by pressure. These reactions will be considered in detail later. Kinetics of the reactions of HF have been studied to determine the effect of reservoir composition, temperature and pressure on the spending of the acid. Secondary effects from by-product formation have been noted and described. The individual reactions of HF on quartz, glass and clay are reported. Mathematical correlations have been drawn, then applied to studies of HF spending in cores obtained from actual producing sandstone formations. The research reported herein is only the beginning of a continuing approach to better understanding and use of HF in petroleum reservoirs. THEORY AND DEFINITIONS Through the years, a concentrated effort has been made to understand the effects of many variables on hydrochloric acid (HCI) spending in limestone. Hendrickson el al., have given mathematical relationships for HC1 reactions which made possible the engineered approach to acidizing. The same variables—temperature, acid concentration, formation composition, pressure and permeability-porosity relationships—which affect HC1 behavior in limestone also govern HF behavior in sandstone. Insoluble by-products of HF reaction have been isolated and identified. Their effect on fluid flow has been measured under varying conditions in an attempt to evaluate the extent of possible damage and means of eliminating it. In general, HF follows the same reaction paths as HCI. It will react with limestone and dolomite with speed and ease. Thin sections of acidized cores show the reaction of HF with limestone or calcite faster than its reaction with either clay or sand. When HF reacts with calcite (CaCO,), theoretically, calcium fluoride (CaF2) is precipitated, and has been blamed as a major cause of reduced permeability. On the other hand, pH and pressure such as that encountered in an underground formation under acid treatment definitely retard CaF2 formation,' so the whole question of CaF, deposition in wells is a subject for study.

Jan 1, 1966

By William H. Breeding

The remarks that follow are based substantially on experience covering 45 years, 80% of which has been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more- difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in inter- mediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1-1/2%. The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present. Most of the rich, readily accessible placers were mined by our forefathers. Current opportunities exist: (1) in remote areas where infrastructure has been absent in the past, or development has been prohibited by adverse ownership - political or commercial; (2) in deposits that could not be mined by equipment available to our forefathers; (3) in deposits unidentified by our forefathers; (4) where the-price-of-product/cost ratio is substantially better than in earlier years; or (5) a combination of those factors. When I entered the placer business in the late 1930s, and subsequently, a prevailing opinion believed that glacial deposits should be avoided as irregular in mineral content and composition, and unrewarding to explore and develop; yet an operator has been mining a fluvio-glacial deposit profitably for the past 17 years. Rich buried placer channels, of ten called paleo-channels were worked in the last century, generally by hand methods, and under conditions that would be unacceptable today. Exploration and mining equipment now available make some of these channels attractive targets. Well-known examples are in California and Australia. The formation of a commercial placer requires a source of valuable minerals. Above primary deposits, there may be eluvial deposits formed by the erosion of gangue minerals and the concentration "in situ" of valuable minerals. Down slope from these deposits are the hillside or colluvial deposits, and below them are the alluvial deposits of redeposited material. Most of the great placer fields of the world are the result of several generations of erosion and deposition. Well-known examples are in California and Colombia. Gold is a very resistant and malleable material, and gold placers may extend for 64 or 80 km (40 or 50 miles) along a river system. Platinum is less malleable, but is very resistant to disintegration. Diamonds are extremely hard, and (especially gem diamonds) may be found over great lengths of a river system. Cassiterite is less resistant to disintegration, and tin placers seldom extend over two miles without resupply from an additional source or sources of mineralizaton. Tungsten minerals are generally more friable, and within a few hundred yards of the source disintegrate to the point that they are uneconomical to recover. Rutile, ilmenite and zircon placers generally result from the weathering of massive deposits, and may be encountered over extensive areas; most are fine grained and durable. What does a geologist or mining engineer look for in placer exploration? The old adage to look for a mine near an existing mine is still valid. You need a source of valuable mineral. Then you require conditions for concentration, which means a satisfactory gradient and/or other conditions that will permit heavy minerals to settle. Nicely riffled gravel, often called a shingling of the bars, is conducive to placer formation. Coarser gravel is logically associated with coarser gold. Excessive clay and/or high stream velocities in narrow channels can carry gold far downstream and distribute it uncommercially over a large area. When material is extremely fine, in situ weathering and concentration become more important. Placers frequently occur distant from lode mines, and one must remember that in a larger watershed the exceptional floods that occur once in a hundred or a thousand years can move great quantities of material long distances. The carrying power of water is said to vary with the fifth or sixth power of its velocity. I am not ready to disagree with Waldemar Lindgren and accept that many commercial placers are substantially enriched by the chemical deposition of gold from solutions; however, I have seen crystalline gold in clayey material quite distant from known sources of primary gold that is dif-

Jan 1, 1985

By Eckley B. Coxe

(WITH FIGURES ON PLATES II, III, AND IV.) I DESIRE to call the attention of the Institute to two deep vertical shafts, which are now being sunk in Schuylkill County, Pennsyl¬vania, about 1 1/2 miles north of Pottsville. These shafts are of interest to the mining engineer, not only on account of the novelty of the method of sinking adopted, which promises to produce a revolution in that branch of mining engineering, but also as examples of the manner in which such work should be undertaken. GEOLOGICAL SKETCH OF THE TERRITORY TO BE WORKED BY THE SHAFTS AND REASON FOR SINKING THEM. The Mammoth or E Vein of the anthracite coal-measures in that part of the Schuylkill region near and north of the town of Pottsville lies at a great depth below the surface, and has, in consequence, never been worked in that locality.

Jan 1, 1873

By R. E. Zinkham, R. J. Goodwin

A mathematical study has been made of the amount of support a cement sheath could provide to casing cemented into the earth. Several assumptions were required to make the analysis, but only two of them are limiting: (I) the pipe must be completely surrounded with cement, and (2) any mud filter cake between the cement and formation has the same physical properties as either the cement or formation. The calculations showed that little support would be provided to the pipe before an unsupported cement sheath failed in tension; however, when the cement is confined between the pipe and wellbore and is loaded in compression, the pipe could receive a considerable amount of support. In fact, the theoretical results indicate the lower grades and larger sizes of pipe could have their working pressures doubled when reasonable compressive loads were applied to a surrounding cement sheath. These data are shown in six charts. Other down-hole conditions such as setting the cement under pressure, increased temperature and cement confinement all tend to increase the potential usefulness of the sheath. Because of size limitations, a laboratory program to verify the most important results of this mathematical study would be very difficult. However, small-scale field tests would be practicable. This paper shows that, if a solid cement sheath can be obtained in the field by either primary cementing or by repair after detection of flaws by surveys such as the new cement-bond logs, the use of this approach to reducing pipe costs merits further consideration. INTRODUCTION A modification in casing design practices is proposed which may either reduce the amount and grade of steel required to contain a specified internal pressure or permit the working pressure to be increased for a specified weight and grade of pipe. One of the more important considerations in casing design is its resistance to collapse; however, Bowers' and, more recently, O'Brien and Goins' have shown many casing programs are unnecessarily conservative in this respect, and they have indicated how savings can be made by designing for more realistic down-hole conditions. Earlier, Saye and Richardson howed that pipe costs could be reduced by considering the cement sheath as a part of the casing string when collapse resistance was being calculated. More recently, Rogers4 has raised the question as to whether a cement sheath might be considered in the design for burst resistance of the cemented casing. Calculations have been made for the increased burst resistance a cement sheath would provide for casing in a wellbore, and the results show that a sizable amount of support could be obtained in some instances. These data are presented in addition to a discussion of several other factors that are considered to affect the burst strength of pipe supported by cement. Two types of support are treated: Case I for tensile loading of the unconfined cement sheath, and Case for compressive loading of the confined cement sheath. ANALYTICAL TREATMENT AND RESULTS CASE I—TENSILE STRESSES IN AN UNCONFINED CEMENT SHEATH Conditions like this would most likely occur in a greatly enlarged portion of the hole where the cement was not in immediate contact with either the formation or a thin and hard mud cake. The mathematical analysis for this condition, as shown in the Appendix, rests on the following concepts. Pressure inside a unit length of pipe causes: (1) a tensile or tangential stress to be exerted over the longitudinal cross-sectional areas of the pipe and cement; and (2) an equal amount of strain in both the pipe and cement that is uniformly distributed over the wall thickness of each. This analysis was then used to make several calculations for a cement sheath around 51/2-in. OD pipe. The results are illustrated in Fig. 1, which shows that a tensile stress of 500 psi is imposed on a 5-in. thick sheath when the casing contains a pressure of only 1,450 psi. It also shows that a 10-in. thick sheath would be stressed to 500 psi in tension when the pipe contained a pressure of only 2,350 psi. Alternatively, if the stress analysis is made by means of the Lame thick-wall cylinder theory, the inner fibers of the 10-in. thick sheath will be stressed to 500 psi in tension when the pressure in the pipe is only 990 psi. This, of course, reveals that an unconfined sheath is of little support to the pipe in burst; however, an entirely different result is obtained when the cement is confined between the pipe and formation.

By Betty J. Laswell, Gerald W. Laswell

If recent trends in the rotary drill market are indicative of future surface mining operating practice, then the move to scaled-up mining equipment by manufacturers may soon be over. Of the 48 different rotary drills currently produced by 12 manufacturers, over 60% were introduced within the past five years. By far, the new drills have been in the "small" class, capable of producing up to a 229-mm-diam (9-in.) blasthole with 222 kN (50,000 lb) or less of down pressure. New rotary drills in the "large" class, capable of producing a 311-mm-diam (12 1/4-in.) blasthole with up to 423 kN (95,000 lb) down pressure, have also been prominent. In the super-size category, new drills producing blasthole sizes to 444-mm-diam (17 1/2-in.) with up to 578 kN (130,000 lb) have been minimal.

Jan 7, 1978

By V. R. Thompson, R. C. Westgren

In a recent paper,1 the solid-solution strengthening of tungsten and tantalum in a portion of the W-T;-MO-C~ alloy system was described. Additions of tantalum and columbium to tungsten led to significant strengthening, and the introduction of dispersions into these alloys was suggested as a means of further increasing strength. Dispersion strengthening of columbium and molybdenum alloys has been studied extensively.2-4 The approach used to dispersion-strengthen molybdenum alloys appeared equally suitable for tungsten alloys, and, therefore, a brief study was undertaken to determine to what extent the introduction of carbide dispersions would strengthen a solid-solution tungsten-base alloy. A base composition of tungsten and 10 to 12 pet Cb was selected; previous work1 had shown that the tensile strength of this solid-solution alloy was 50,000 psi at 3000°F. For the study of the effects of small additions of

Jan 1, 1964

By E. Teghtsoonian, E. M. Schulson

The tensile behavior of bcc ordered P' AuZn single crystals (CsCl structure) has been investigated under varying conditions of temperature, composition, and orientation. Between -0.2 and 0.4 T, multi-stage hardening occurs fm stoichiometric and nonstoichio-metric crystals oriented near the middle of the primary stereographic triangle. At higher and lower temperatures, parabolic type hardening occurs, followed by work - softening at the higher temperatwes. Deviations from stoichiometry give rise to increased flow stresses. Multi-stage hardening was observed for most orientations, except along the [loll-[lll] boundary and near the [001] corner of the stereo -graphic triangle, where parabolic type hardening occurs. Along two slip systems, (hk0)[001] and (, operate simultaneously while in the [001] comer, slip occurs mainly on the system. Electron microscopy of deformed crystals revealed bundles of edge dislocations forming walls approximately Perpendicular to the glide plane. In general the plasticity of 4' AuZn closely resembles the plasticity of bcc crystals. In recent years, considerable interest has arisen concerning the mechanical properties of the CsCl type intermetallic compounds Ag Mg,'- Fe co,' and Ni Al.'-' The compound P'AuZn is structurally similar. It has a low and congruent melting point of 725"~,'" remains ordered up to the melting point,16 and pos-esses a range of solid solubility from 47.5 to 52.0 at. pct Au at room temperature.15 The present paper reports the results of an investigation on the general tensile behavior of material in single crystal form. Some dislocation configurations characteristic of the deformed state are also reported. The results of a detailed study of the slip geometry in AuZn are presented in a separate paper.17 PROCEDURE Alloy preparation, crystal growing techniques, and the procedure followed in selecting specimens of minimum composition variation are reported elsewhere.17 Dumb-bell shaped tensile specimens were prepared by carefully machining single crystals in a jewellers' lathe to a gage length of 0.80 in. and diam of 0.090 in. Back-reflection Laue X-ray patterns and room temperature tensile tests revealed that machining damage could be eliminated by electrochemically polishing 0.005 in. from the machined surface followed by annealing at 300°C for 1 hr. Specimens were polished in fresh 5 pct KCN solution (40°C, 12 v). Experiments were performed by gripping specimens in a self-aligning pin-chuck and threaded collet system, then straining in a floor model Instron tensile machine. All tests were performed in duplicate. Experimental variables included temperature, composition, and orientation. Unless otherwise stated the strain rate was 2.5 x 10"3 per sec. Liquid testing environments included nitrogen (WOK), nitrogen cooled petroleum ether (133" to 293"K), and silicone oil (293" to 488°K). Resolved shear stress-shear strain curves were electronically computed from autographically recorded load-elongation curves. Stress and strain were resolved on the macroscopic noncrystallographic (hkO) [001] system operative under the specific test conditions of temperature, strain rate, and orientation reported earlier.17 RESULTS The temperature dependence of the work-hardening curves is shown in Fig. 1 for gold-rich crystals of 51.0 at. pct Au oriented near the center of the stereo-graphic triangle. Over the range of intermediate temperatures from -200" to 400°K, they are very similar to those classically observed for fcc metals (reviewed by Nabarro et al.).'' The beginning of deformation is characterized by a region of decreasing hardening rate, stage 0, which is followed by a region of low linear hardening, stage I, and then a region of higher linear hardening, stage 11. At the higher temperatures, stage 111 is observed, a region of decreasing hardening rate. Over the intermediate temperature range, the extent of stage 0 and of the slow transition between stages I and I1 decreases with increasing temperature. Total ductility is large, often greater than 300 pct shear. As the temperature is either increased or decreased, the extent of stage I is decreased, giving rise to parabolic type flow and reduced ductility. Similar temperature effects have been reported for bcc ~r~stals.~~-~~ Below -14O°K, hardening is terminated in brittle fracture while above -400°K. initial hardening is followed first by work-softening and then by chisel-edge type ductile fracture. Stoichiometric (50.0 at. pct Au) and Zn-rich (51.0 at. pct Zn) crystals were also tested from 77" to -500°K. The effect of composition on the flow behavior is illus-

Jan 1, 1970

By E. S. Bartlett, D. N. Williams

QUANTITATIVE values for the oxidation rate of unalloyed molybdenum in air at temperatures above the melting point (1460°F) of the characteristic oxide are contained in the literature as a result of previous investigations. Lustman' reported values corresponding to 0.36 in. penetration per day (IPD) at 1500 and 1600°F in still air, noting essentially no variation in rate with temperature. Jones, Spretnak, and Speiser' reported values corresponding to 0.14 and 0.13 IPD at 1500 and 1800°F, respectively, in still air, attributing the decreased oxidation rate at higher temperatures to a lesser accumulation of the corrosive molten oxide on the surface at the higher temperature as a result of increased volatilization rate. Harwood3 ecently summarized work in the field, presenting generalized data corresponding to 0.48 to 0.96 IPD at 1800°F and 0.55 to 0.83 IPD at 1700°F in slowly flowing air. In a recent program at Battelle, it became desirable to know more about the characteristic oxidation behavior of molybdenum under varying conditions of temperature and atmosphere. Using oxidation-test apparatus designed for dynamic, continuous recording of weight change during testing,' values for the oxidation rate of molybdenum were obtained at temperatures from 1400 to 2150°F. In addition the effect of air flow on the oxidation rate was studied briefly at temperatures of 1600, 1800, and 2000°F. Exhaust of the contaminated atmosphere from the oxidation chamber was effected by an impeller pump attached to a 3/16-in.-diam opening in the oxidation chamber. The volumetric exhaust rate (cubic feet per hour) was normally maintained slightly in excess of the input rate to avoid condensation of MOO,,' on the sample suspension rod. The entering atmosphere was preheated prior to admission to the oxidation chamber by a 1 1/2-in.-diam cup packed with shredded asbestos. The experimental data are presented in Table I. Comparing conditions 2 and 3 (taking into account the temperature difference) and conditions 8 and 9. shows that in the absence of forced exhaust an atmosphere of moving air results in greater oxidation rate than a stagnant atmosphere. The use of forced exhaust, as shown by comparing conditions 3 and 4 and conditions 14 and 15: resulted in an even greater increase in oxidation rate. By virtue of the size of the atmosphere input and exhaust openings, it was calculated that the exhaust velocity was about 60 times that of the input velocity for essentially equal volumetric flow rates. Because of the proximity (about 3/4 in.) of the exhaust port to the specimen, it is logical to assume that cleansing of the atmosphere immediately surrounding the specimen was accomplished much more efficiently by the exhaust flow than by the input flow at a constant-volumetric flow rate. Also, it can be seen by comparing conditions 4 through 7 and conditions 11 through 13 that increasing the rate of atmosphere flow (by increasing input velocity with a proportional increase in exhaust velocity) above some optimum value has little, if any, further effect on the oxidation rate. These results suggest that there is a maximum oxidation rate for molydenum at a given temperature which is obtained when conditions are maintained such that the partial pressure of MOO3 in the atmosphere surrounding the specimen is at a low value. By controlling the partial pressure of MOO, surrounding the sample, it is possible to control the rate of volatilization of MOO:, from the surface. This, in turn, affects the rate of oxidation, since the thickness of the MOO3 layer determines the amount of oxygen which will be able to reach the reaction surface.' When the liquid oxide layer is less than some critical thickness, i.e., when the volatilization rate is high, enough oxygen is transported to the active surface to permit oxidation to proceed at the maximum rate allowed by the kinetics of the oxidation reaction. However, if the volatilization of MOO,, is suppressed, the thickness of the layer of MOO3 on the surface increases, and the diffusion of oxygen through the oxide layer becomes the rate-controlling step in the oxidation process. The lack of agreement between the present results and those of previous investigators is presumed to be due to differences in removal of the oxidation product (Moo,) from the immediate vicinity of the sample. By comparing conditions 1, 5, 10, 12 and 14, it is seen that when forced exhaust was used the oxidation rate of molybdenum increased with increasing temperature. A rapid increase was observed between 1400 and 1600°F, attributable to the effects

Jan 1, 1959

By A. J. Phillips, C. H. Mathewson

BERYLLIUM, magnesium, zinc and cadmium, together with mercury, constitute a coherent sub-group of the periodic system and these metals, excepting mercury, have been studied in sufficient detail by the new X-ray diffraction methods to prove their common adherence to the hexagonal close-packed type of crystal structure with a progressive increase in axial ratio as we pass through the group from beryllium to cadmium. The first four columns of Table 1 summarize the data on crystal structure of these metals reported in the International Critical Tables.1 The last two columns are based on results obtained in the present investigation. [ ] Twinning has often been observed in zinc and cadmium. The general aspects of this twinning are abundantly illustrated by photomicrographs, diagrams, etc., in the papers by Romig, and Mathewson and Phillips reported to this Institute in 1927.2 A determination of the composition

Jan 1, 1928