Search Documents

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By George Rice

WHEN miners in the interior coal fields of the United States began the practice of blasting the coal without undercutting, or what is known as "shooting off the solid," many explosions resulted, some of them of great extent and 'violence, and attended with large loss of life. One of the means adopted for preventing this large loss of life, though not preventive of explosions, was to employ shot firers to discharge the shots when all the other employees had gone out of the mine at the end of the day's shift. This system still prevails in most of the Central and Southwestern mines. Following the disaster at Winter Quarters mine, Utah, May 1, 1900, in which 200 lives were lost, a system of firing shots electrically from outside and when the men were out of the mine was adopted at the mines of the Utah Fuel Co.1 This system has also been used in France in certain mines that are subject to instantaneous outbursts of carbonic acid gas. These outbursts generally occurred at shot-firing time, on account of the blasts releasing the gas held in crevices under high pressure. The system was also adopted at a number of other mines in Utah, at the Cokedale mine, Colorado, at the Dawson mines, New Mexico, and in some mines of the Tennessee Coal, Iron & Railroad Co. in the Birmingham Ala. district; and more recently in certain mines in Iowa and Kansas. At first there was considerable trouble from misfires, and in a few instances from premature firing, while men were in the mine, through the shot-firing lines becoming crossed with power lines. Fortunately, however, no loss of life resulted from such premature firing within the knowledge of the writers, and latterly this danger has been reduced to a minimum by certain measures of precaution. The proportion of misfires, or failures of individual shots to fire, has also been reduced to a very small

Jan 10, 1914

By H. P. Greenwald

THIs paper brings forward a discussion that was prepared for the meeting of the Coal Division in Chicago in 1938.1 War in Europe less than a year after that meeting, followed by our defense preparations and entry into the conflict, caused general cessation of large-scale experimentation on the subject, and it is best to confine this paper to events in the United States during the five-year period since the preceding paper was written. The views of members of the Coal Division's Committee2 on Rock-dust-ing for 1943 were obtained before this paper was written and the manuscript was reviewed by them. Extent of Rock-dusting Statistics on the use of rock dust in the United States during the years 1930-1933, appearing on page 97 of Volume 139 of the Transactions are extended in Table I herein through the year 1941. The results through 1933 did not appear encouraging, but there has been improve-ment since that date. It has always been true that the larger operations were the ones that used rock dust. In 1941 only 10 per cent of the mines in the country used rock dust, but they produced 57 per cent of the coal, employed just under 50 per cent of the miners, and accounted for 52 per cent of the man-hours. Unfortunately, collection and compilation of these statistics are slow procedures, and figures dealing with the tremendous war expansion of the industry are not likely to be available for a year or more. In 1941 the five leading states in regard to percentage of man-hours worked in mines using rock dust were: Utah, 92.1; Wyoming, 79.3; Alabama, 77.4; New Mexico, 72.5; West Virginia, 65.3. The first four states were the same as in 1933, but West Virginia displaced Washington in fifth place. On the basis of pounds of rock dust used per ton of coal, the five leading states in

Jan 1, 1944

By H. P. Greenwald

THIs paper brings forward a discussion that was prepared for the meeting of the Coal Division in Chicago in 1938.1 War in Europe less than a year after that meeting, followed by our defense preparations and entry into the conflict, caused general cessation of large-scale experimentation on the subject, and it is best to confine this paper to events in the United States during the five-year period since the preceding paper was written. The views of members of the Coal Division's Committee2 on Rock-dust-ing for 1943 were obtained before this paper was written and the manuscript was reviewed by them. Extent of Rock-dusting Statistics on the use of rock dust in the United States during the years 1930-1933, appearing on page 97 of Volume 139 of the Transactions are extended in Table I herein through the year 1941. The results through 1933 did not appear encouraging, but there has been improve-ment since that date. It has always been true that the larger operations were the ones that used rock dust. In 1941 only 10 per cent of the mines in the country used rock dust, but they produced 57 per cent of the coal, employed just under 50 per cent of the miners, and accounted for 52 per cent of the man-hours. Unfortunately, collection and compilation of these statistics are slow procedures, and figures dealing with the tremendous war expansion of the industry are not likely to be available for a year or more. In 1941 the five leading states in regard to percentage of man-hours worked in mines using rock dust were: Utah, 92.1; Wyoming, 79.3; Alabama, 77.4; New Mexico, 72.5; West Virginia, 65.3. The first four states were the same as in 1933, but West Virginia displaced Washington in fifth place. On the basis of pounds of rock dust used per ton of coal, the five leading states in

Jan 1, 1944

By Robert P. Roberts

In order to obtain data on the thermal effect of the blast-furnace jacket and on the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times. The method used was as follows: The overflow from the jacket to be tested was arranged to discharge at will into a barrel, mounted upon platform scales. The discharge temperature was read just before turning the water into the barrel, and just before turning it back to the sluice; if the test lasted more than a minute, additional temperature readings were taken at 1-min. intervals from start to finish. The elapsed time of running the water into the barrel was determined with a stop-watch, and this figure, combined with the in-

Jan 1, 1914

By Walter Kauenhowen

Germany's crude oil production during 1935 totaled 3,007,711 bbl., an increase of 36.6 per cent over the 2,202,214 bbl. produced in 1934. The Nienhagen-Haenigsen field furnished 77 per cent of the total 1935 production. Cumulative production figures for Germany's two most important oil fields, Wietze and Nienhagen, show that during the period from 1872 to the close of 1935 the Wietze field produced 13,325,536 bbl. and the Nienhagen field 9,340,870 bbl. Table 1 gives statistics of German production since 1928, arranged both by fields and by oil provinces. Fig. 1 demonstrates the production of the various German fields since 1890. New Fields Discovered During 1935 five new fields came into production. The first of these, the Moelme-Hoheneggelsen field near Hanover, was opened up in April. This region has been sporadically drilled for oil since 1882, but not until 1935 was production on a commercial scale obtained. The oil comes from Mesozoic sandstones on the flanks of a shallow salt plug. Also during April, oil was found in commercial quantities in the Rhine valley at Forst, near Bruchsal. Tertiary and Mesozoic sandstones cut by faults of the Rhine Graben form the reservoir structures in this area. In July a wildcat well drilled on the Fallstein structure, a broad Triassic anticline near Halberstadt, came in as a producer from Permian (Zechstein) dolomite. In September commercial oil mas found at Gifhorn, near Braunschweig, in Wealden sandstones associated with a shallow, geophysically discovered salt plug. During the same month production was obtained at Heide, in Holstein, from the Permian Rotlie-gendes formation, in a structural high on which oil seepages have been known for years. Drilling Activities Published information indicates that during 1935 drilling totaled 574,000 ft., as compared with 436,000 ft. in 1934; 233,000 ft. in 1933 and 151,000 ft. in 1932. The German Government is subsidizing wildcat

Jan 1, 1936

By Arthur C. Simmons

The Pennsylvania-grade oil industry suffered a serious decline in 1938, which can be largely accounted for by the decrease in the use of lubricating oil. Production was considerably lower than in previous years and prices were very much lower. Operating profits undoubtedly were lower than the year 1933, for the average price of Bradford crude in 1938 was $1.898 as compared with $1.86 in 1933, and the difference in average price of $0.04 per barrel was more than offset by increased operating costs and taxes. Bradford Field Production in the Bradford field in the state of Pennsylvania averaged 36,759 bbl. per day in 1938 as compared with 41,300 bbl. in 1937. The decline in average daily production of 4541 bbl. can be attributed to low market price and pipe-line proration rather than to the actual physical capacity of the field. Pipe-line proration was in effect for the last eight months of the year and the daily average production per month fluctuated between a maximum of 41,852 bbl. per day in March 1938 and a minimum of 33,649 bbl. per day in November. Production figures for Bradford field have been corrected to include only the parts of the Bradford field that arc within the state of Pennsylvania, but the well-completion data for the Bradford field cannot be segregated and include those of the entire Bradford field, part of which is in Sew York state. Production from the Bradford field was obtained almost wholly by water-flooding and no radically new methods or practices occurred. Intensive research work was carried on both by individuals and companies and as a cpooperative enterprise, and minor improvements are gradually occurring in spacing, shooting, application of pressure and water conditions. Drilling Central and Southen Pennsylvania.—Pennsylvania production in central and southern Pennsylvania was obtained largely by air and gas repressuring together with the usual amount of natural production, and the repressuring operations in other than the Bradford field have not

Jan 1, 1939

By Walter Kauenhowen

Germany's crude oil production during 1935 totaled 3,007,711 bbl., an increase of 36.6 per cent over the 2,202,214 bbl. produced in 1934. The Nienhagen-Haenigsen field furnished 77 per cent of the total 1935 production. Cumulative production figures for Germany's two most important oil fields, Wietze and Nienhagen, show that during the period from 1872 to the close of 1935 the Wietze field produced 13,325,536 bbl. and the Nienhagen field 9,340,870 bbl. Table 1 gives statistics of German production since 1928, arranged both by fields and by oil provinces. Fig. 1 demonstrates the production of the various German fields since 1890. New Fields Discovered During 1935 five new fields came into production. The first of these, the Moelme-Hoheneggelsen field near Hanover, was opened up in April. This region has been sporadically drilled for oil since 1882, but not until 1935 was production on a commercial scale obtained. The oil comes from Mesozoic sandstones on the flanks of a shallow salt plug. Also during April, oil was found in commercial quantities in the Rhine valley at Forst, near Bruchsal. Tertiary and Mesozoic sandstones cut by faults of the Rhine Graben form the reservoir structures in this area. In July a wildcat well drilled on the Fallstein structure, a broad Triassic anticline near Halberstadt, came in as a producer from Permian (Zechstein) dolomite. In September commercial oil mas found at Gifhorn, near Braunschweig, in Wealden sandstones associated with a shallow, geophysically discovered salt plug. During the same month production was obtained at Heide, in Holstein, from the Permian Rotlie-gendes formation, in a structural high on which oil seepages have been known for years. Drilling Activities Published information indicates that during 1935 drilling totaled 574,000 ft., as compared with 436,000 ft. in 1934; 233,000 ft. in 1933 and 151,000 ft. in 1932. The German Government is subsidizing wildcat

Jan 1, 1936

By Arthur C. Simmons

The Pennsylvania-grade oil industry suffered a serious decline in 1938, which can be largely accounted for by the decrease in the use of lubricating oil. Production was considerably lower than in previous years and prices were very much lower. Operating profits undoubtedly were lower than the year 1933, for the average price of Bradford crude in 1938 was $1.898 as compared with $1.86 in 1933, and the difference in average price of $0.04 per barrel was more than offset by increased operating costs and taxes. Bradford Field Production in the Bradford field in the state of Pennsylvania averaged 36,759 bbl. per day in 1938 as compared with 41,300 bbl. in 1937. The decline in average daily production of 4541 bbl. can be attributed to low market price and pipe-line proration rather than to the actual physical capacity of the field. Pipe-line proration was in effect for the last eight months of the year and the daily average production per month fluctuated between a maximum of 41,852 bbl. per day in March 1938 and a minimum of 33,649 bbl. per day in November. Production figures for Bradford field have been corrected to include only the parts of the Bradford field that arc within the state of Pennsylvania, but the well-completion data for the Bradford field cannot be segregated and include those of the entire Bradford field, part of which is in Sew York state. Production from the Bradford field was obtained almost wholly by water-flooding and no radically new methods or practices occurred. Intensive research work was carried on both by individuals and companies and as a cpooperative enterprise, and minor improvements are gradually occurring in spacing, shooting, application of pressure and water conditions. Drilling Central and Southen Pennsylvania.—Pennsylvania production in central and southern Pennsylvania was obtained largely by air and gas repressuring together with the usual amount of natural production, and the repressuring operations in other than the Bradford field have not

Jan 1, 1939

By Dale E. Walker

The Captain mine came into being under the following circumstances: 1) Commonwealth Edison had need for fuel for the generation of electricity in their Chicago service area. 2) Southwestern Illinois Coal Corp. had an ample supply of coal in the Illinois No. 6 and No. 5 seams. 3) The Gulf, Mobile & Ohio R.R. had a one-line transportation system with the capability of transporting coal from the Captain mine to Commonwealth Edison. These fortuitous conditions permitted an effective three-way partner- ship to develop. Commonwealth Edison had built a new generating station at Joliet, Ill., across the Illinois River from the existing station, to supplement their power-generating capacity for the Chicago area (Fig. 1). The annual requirement of the Joliet station is approximately 4.5 million tons of coal. From large reserves of coal in the No. 6 and No. 5 seams, Southwestern Illinois Coal Corp. contracted to supply Commonwealth Edison with approximately 6 million tons annually from its Captain mine. The logical carrier was Gulf, Mobile & Ohio, whose mainline travels through this coal field and also passes by the Joliet station on its way to Chicago. This railroad has been moving Southwestern's coal from the Streamline mine for more than 30 years. The basic ingredients of timing, scheduling, moving, and handling were adopted by the three parties, the precise details being worked out jointly. To do this, each group had to know its requirements exactly. The initial schedule was drawn up and tentatively approved, with each party taking a hard look at its own requirements and commitments to make certain that the schedule could be met on a normal daily basis. With only minor changes, the final schedule was adopted, each participant feeling that it had a sufficient factor of safety to maintain steady operation. Each party agreed to help the other in time of emergency. When a delay occurs in any part of the operation, the other

Jan 1, 1969

By Eugene A. Stephenson, Leon J. Pepperberg

The natural gas industry is essentially a byproduct of the oil industry. When first discovered the gas was usually regarded as a nuisance, and even when found immediately associated with oil, or suspected to be so, it was customary to blow it freely into the air, in the hope that gas would shortly be replaced by a flow of oil. The early methods of production,' transportation, and utilization were neither economical nor efficient; the chief value of gas was based on its use as a fuel, with no regard to (1) its effect. upon the oil with which it was associated, (2) its importance as a lifting agent, or (3) to its possibilities for the manufacture of byproducts. The spread of scientific research among major gas and oil companies, manufacturers, and academic groups, has gradually brought recognition of the fact that many of the technical problems bearing on production, transportation and utilization are common to both the gas and the oil industry. A few of the problems that have received serious study, and from which highly gratifying results have been obtained, are: (1) gas measurement, (2) oil well and gas well capacity tests, (3) elimination of field waste, (4) design of pipe lines and compressor stations, (5) extraction of constituents which might interfere with the normal flow of gas through the line, (6) control of reservoir pressure, (7) estimation of reserves of both oil and gas, (8) control of water encroachment, (9) measurement of factors which influence fluid movement through sands, (10) solubility of gases in oils, (11) effect of dissolved gases upon the properties of the solution. These investigations have demonstrated that almost every problem relating to oil production also involves some phase of natural gas engineering. During the past 15 years the use of experimental methods for the discovery and measurement of obscure, influencing factors, which cannot be determined purely by hydrodynamic or thermodynamic analyses, have contributed much towards the progress made in solving the problems of the oil and gas industries. Most of the experimental work on

Jan 1, 1934

By E. Buehler, E. Berry

HE magnetic properties of dilute palladium alloys are of fundamental interest.''' Neutron diffraction studies3 have indicated that a better understanding of the behavior of these alloys could be realized with the availability of high-purity single crystals of palladium. Crucible melts of 99.999 pct pure palladium were found inadequate for such research. In a successful effort to fill this need, floating zone refining of palladium was undertaken. In this note the results of the initial experiments are reported. Zoning was accomplished in an argon atmosphere using 450 kc rf generator for an energy source. Samples 5 to 6 mm in diam were suspended in a gastight quartz envelope which could be moved vertically through the rf coil. A nominal upward traverse rate of 1.5 mm per min was maintained during a pass. Close coupling was found to be essential for stable retention of the liquid in the zone. Single crystals averaging 3.5 cm in length were obtained. Laue photography showed them to be continuous single crystals without gross imperfections. Several criteria were used for evaluation of the purity of the zoned material: magnetic behavior, low-temperature specific heat and residual resistivity ratios. Table I shows the residual resistance ratios obtained for two samples, one subjected to a single pass, the other zoned four times. It is appilrent that palladium can be zone refined with the electrically active impurities being transported toward the tail end. A decrease in susceptibility for zone-melted specimens over any previously measured material from 1.5" to 80'~ has been obserted by H. J. Williams and R. C. Sherwood4 substantiating the residual resistance data. The specific heat measurements are currently being made3 and will be published at some later date. Discussions with J. H. Wernick and S. C. Abrahams are acknowledged. We also wish to thank G. F. Brennert for the residual resistance measure ments.

Jan 1, 1962

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc, may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, to¬gether with the names of its president and its secretary, may be published in MINING AND METALLURGY or the DIRECTORY of the Institute. The members of such a society will not be named individually on the membership list of the Institute, but may at any time be proposed for election as associates or junior associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied by suitable testimony as to character and qualifications, will have special weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership. The Affiliated Student Societies receive the following privileges: 1 A copy of MINING AND METALLURGY free; 2. The use of Employment Service; 3. The use of MINING AND METALLURGY for publicity purposes, such as printing notices of their activities, etc ; 4. Assistance in obtaining speakers for their meetings, lists of moving-picture films, etc. To retain the privileges of the Affiliated Student Society, its officers must keep in touch with the Secretary of the Institute and advise him of its activities. The foregoing plan is not confined to students in mining engi¬neering or metallurgy. Any undergraduate society of engineers may avail itself of the privileges offered. Societies desiring to be recognized as Affiliated Student Societies are requested to make application to the Secretary of the Institute, giving particulars as to their nature, membership and officers. The accompanying list gives the names of the Affiliated Student Societies as of April 15, 1927, and their presidents and secretaries, in so far as they have been reported to the Secretary of the Insti¬tute.

Jan 1, 1923

By Frederic Laist

IN the spring of 1931 an experiment was made at Anaconda with a small reverberatory furnace, with which was combined a roasting shaft. The arrangement is shown in the accompanying drawing (Fig. 1) and requires but little explanation. The general idea was to roast .flotation concentrates, mixed with the proper fluxing materials, by dropping them down a heated shaft, from which the calcines would enter the smelting zone of the reverberatory furnace through an opening in the roof. The hearth of the reverberatory was 3 ft. wide by 21 ft. long. The roasting shaft was 3 ft. square inside and had an effective height of about 20 ft. . The reverberatory furnace was arranged so that it could be charged either directly through the roof with regular hot calcines, in the usual manner, or by means of the shaft, at the top of which were a feed-ing arrangement by which cold flotation concentrates, suitably fluxed, could be fed continuously and a pipe through which cold air was blown in. Means were provided for distributing the feed over the cross-section of the roasting shaft. At first a mechanical arrangement was used but later it was found that a simple cone served the purpose equally well and gave less operating trouble. On account of the small size of the equipment, it was realized that absolute capacity and fuel consumption figures would mean but little. It was not to be expected that ratios comparable to those obtained in large furnaces could be gotten, and the only way in which any idea could be obtained as to the possibilities of the combination furnace was to run it in parallel with the reverberatory furnace charged in the usual manner and operating without the shaft. The results of such parallel runs are given in Table 1. The amount of oil burned in the reverberatory was purposely maintained at substantially the same rate during both runs in order that the benefits resulting from the shaft might be gaged.

Jan 1, 1933

By Peter B. Scotland

The mines of the Arizona Copper Co. are situated in the Morenci-Metcalf copper district in southeastern Arizona. This copper-bearing district covers a triangular mountainous area of about 3 square miles, rising abruptly from the gravel plateau of the surrounding country. In this area, an immense intrusion of porphyry lias displaced, shattered, and engulfed the shales, limestones, and quartzites formerly bedded on the basal granite. Outcrops of oxide ore were discovered in 1873, and these surface ores were found to connect in depth with large bodies of high-grade oxide ores in the limestones and shales. The mining of these high-grade ores continued until about 1893, when their rapid exhaustion led to the discovery and exploitation of the low-grade sulphide ores in the adjoining porphyry. Methods of concentration were then devised and the low-grade ores finally rendered profitable. The Arizona Copper Co. and the Detroit Copper Mining Co., operating in the same district, were the pioneers in the successful development of the low-grade "porphyry" properties of to-day. The largest mines of the Arizona Copper Co. are the Humboldt and Clay at Morenci, and the Coronado, Metcalf, and King at Metcalf. These mines produce about 4,000 tons daily of concentrating ore containing from 2.5 to 2.8 per cent. copper. The topography of the country is very rugged and mining operations are conducted principally through adit levels. A few of the mines are opened by shafts, the deepest being 1,100 ft., in the Coronado mine. Ore Occurrence The low-grade sulphide ore occurs as: (1) disseminated deposits in the main stock of quartz porphyry; (2) lode deposits in fault fissures in granite. The high-grade oxide ores were found as tabular deposits in limestone and shale close to contacts with porphyry dikes. Low-grade oxide ore formed the outcrop of some of the sulphide orebodies; the majority of the outcrops, however, were barren.

Jan 1, 1915

By A. D. McMaster, M. L. Gimpl, N. Fuschillo

There is interest in the use of rhenium metal films as resistive elements in thin-film circcits, and already some zvork has been done using er)aporated rhenium films. It has been found that rheniim films protected from the atmosphere by an evaporated layer of silicon monoxide show excellent electrical stability. Unprotected films, however, are subject to aging- effects, notably the increase in electrical resistivity as a function of time. This phenomenon can be understood as primarily one of oxidation of the thin films. This paper is concerned with the study of the oxidation and crystallization behavior of such unprotected films. It has been found that the oxidation rates are a function of the substrate temperatures used during the deposition of Lhe metal films. The strictures observed in the films are correlated with the film resistivities and some data are presented to establish the existence of the various types of oxides of rhenium. ThERE is some interest in the use of thin films of rhenium metal as resistive elements in monolithic, thin-film integrated circuits. Some work has been done using evaporated films and it has been found that such films, if protected from the atmosphere by an evaporated layer of silicon monoxide, show excellent electrical stability up to temperatures of 500"." Rhenium films unprotected from the atmosphere tend to age and the electrical resistivity of the films increases as a function of time. Rhenium films, of the order of <100A thick, prepared by electron-beam evaporation techniques are found to oxidize very readily when exposed to dry air at room temperature. It would seem, therefore, that this aging phenomenon could be attributed to the oxidation of the metal films. In this investigation, the oxidation and crystallization behavior of thin films of rhenium evaporated onto silicon monoxide substrates were studied as a function of the substrate temperatures used during the evaporation. The films were examined using electron-microscopy and electron-diffraction techniques. EXPERIMENTAL RESULTS Rhenium metal was evaporated onto suitable prepared substrates which were heated to various temperatures. The evaporations were performed in a vacuum of approximately 5 x 1CT5 torr. The evaporation was carried out at a rate of approximately 10A per omin. The final film thickness was approximately lOOA and the resistance ranged from 5000 to 10,000 ohms per square. The substrates used for supporting the metal films were made by evaporating 75A of silicon monoxide onto freshly cleaved mica. The silicon monoxide film was then floated off the mica by immersing the composite in water. The film could then be picked up on a clean nickel grid. Silicon monoxide substrates were chosen because of their similarity to quartz and glass substrates commonly used for making thin-film resistors. Fuschillo, Gimpl, and McMas-ter have also shown that silicon monoxide films have only minor structural changes at temperatures up to 800°C. This fact simplified the interpretation of any changes observed in the electron micrographs or electron-diffraction patterns obtained from the deposited rhenium films. After the evaporations were completed, the substrates were cooled to room temperature, except where noted differently, before the coated substrates were removed from the vacuum system. All aging of the deposited films was done in a desiccator. The evaporated films were examined in an electron microscope equipped with a hot stage that would permit continuous observations of the samples up to temperatures of 1000°C. RESULTS A series of electron micrographs of the rhenium films deposited on the silicon monoxide substrates are shown to Figs. 1 to 3. In all cases, the metal films are approximately 100A thick and the micrographs were taken 1 hr after the deposition was completed. here was no apparent structure in the films deposited on the substrates held at the higher temperatures. The

Jan 1, 1967

By J. Washburn

Two simple types of dislocation distribution were introduced into zinc crystal specimens and the effect of each on the stress-strain curve was investigated. Quantitative results were obtained for simple edge dislocation arrays and for an array of screw dislocations lying in the slip plane. A CCORDING to present knowledge, the disloca-tions present in large annealed metal crystals can be divided into two somewhat arbitrary groups: 1—single dislocation lines distributed more or less at random or forming elements of a three-dimensional network in which the distance between adjacent dislocations is of the order of 10 2 to lo-&apos; cm and 2— widely separated planar arrays of edge dislocations forming dislocation walls or small angle boundaries within which adjacent dislocation lines are spaced at much smaller distances (lo-&apos; to 10- hm). The former can be considered as a dislocation interpretation of the mosaic crystal proposed by Darwin and Ewaldl, &apos; 40 years ago to account for anomalously high integrated intensities of X-ray diffraction maxima. Small angle boundaries, although now known to be present in most single crystals used for mechanical testing, were not generally recognized by the early workers. This was partly due to the fact that only recently have improved X-ray and metal-lographic techniques been available for checking the macroscopic perfection of crystals."" It has long been known that changes in growth conditions and in annealing procedure, which might logically be expected to cause variations in the structural details of both the dislocation network and of dislocation boundaries, produce marked variations in some mechanical properties such as yield strength." However, no quantitative experimental correlations between changes in dislocation distribution and changes in mechanical properties have yet been made. Such a correlation has been difficult to obtain because, even when great care is exercised to keep the histories of a number of single crystal specimens identical, it usually has not been possible to avoid considerable variation in macroscopic per- fection.&apos; The number and orientation of dislocation boundaries vary from specimen to specimen. This has probably been an important contributing factor to the large scatter in the results of most mechanical measurements on pure single crystals. Some recent experiments"% ith single crystals of zinc have shown that the presence of dislocation boundaries in a specimen can increase its resistance to deformation by slip. With polycrystalline aluminum and nickel, there is also evidence that dislocation boundaries within the individual grains of the aggregate can increase the resistance of the material to plastic deformation, either as measured by tension tests at room temperature or by creep tests at higher temperatures.&apos;" " Although the foregoing observations seem to have established the fact that substructure can have a strengthening effect, the test conditions were too complex to give much information concerning the mechanism. In the foregoing cases, a network of intersecting boundaries having various orientations and boundary angles were present. Before their apparent strengthening effect can be understood, it will be necessary to isolate and study separately the effect of a number of variables: 1—boundary angle, 2—boundary orientation with respect to the active slip direction, 3—number of boundaries, 4—intersections of boundaries, 5—detailed structure of the boundaries, and 6—interaction of impurity atoms with dislocations in boundaries. The object of the present work was to study the effect of dislocation boundaries on flow stress under the following simple experimental conditions: 1— substantially pure shear deformation and 2—boundaries of controlled angle, orientation, and number. In this way, it might be possible to distinguish the important variables from the relatively unimportant ones. Experimental Procedure Stress-strain curves of hexagonal metals are generally nearly linear even out to very large strains."

Jan 1, 1956

By F. W. Jessen, N. Lamont

The effect of an existing fracture or joint plane, which may exist in a rock, on the extension of a hydraulically induced fracture through the rock has been investigated in the laboratory. By use of a series of models made from various outcrop rocks, the width and orientation of existing fractures do not alter the extension or direction of the hydraulic fracture. The results, which conform quite well with the Grifith theory of failure, are illustrated by a series of photographs of the various models. INTRODUCTION The process of hydraulic fracturing has been widely used in the oil industry since its introduction in 1948 and has made possible the production of many reservoirs which would have been uneconomical prior to this process. Numerous studies of the mechanics of the process2-h nd of the effects of oriented fractures on recovery&apos;.&apos; have appeared in the literature. The increased recoveries led to attempts to predict the orientation of hydraulic fractures at the wellbore and to the development of methods to control this orientation. Field tests have been devised"." which indicate the validity of theoretical predictions of fracture orientation at the borehole. The direction of extension of hydraulic fractures from the borehole has not received much attention since most studies have predicted, at least implicitly, that a fracture will continue in the same plane unless a change of state of stress in the rock occurs. Since such predictions are based on the assumption of rock homogeneity, the effects of rock heterogeneities are left unknown. Most sedimentary rocks are composed of layers which reflect the changing depositional conditions of geological time. In addition, the more competent rocks frequently are fractured and jointed as the result of structural deformations or tectonic movements. Evidence of such joint systems exists in many surface outcrops, and it can be assumed that similar systems occur in many subsurface rocks, although the individual joints may be rather tightly closed due to overburden forces. This paper investigates the effect that an existing fracture in a rock would have on the direction or orientation of an extending or advancing hydraulic fracture when it intersects the existing fracture. The study was conducted on small rock models under triaxial stress conditions. The results indicate that an existing fracture will have little effect on the hydraulic fracture. THE MODEL STUDY The rock model represents an elemental portion of the earth containing an existing fracture which is located at some distance from a borehole from which hydraulic fracture is being extended. A generalized view of a model is presented in Fig. 1. The models were constructed from cement blocks and natural rocks. The various materials tested and some of the physical properties are listed in Table 1. The rocks were cut into rectangular blocks with dimensions of 11/2 X3Y2 X4 to 8 in. An initial slot was cut into the end face of each block along the longitudinal axis normal to the top face. The slot was filled with plastic aluminum along its outer edge to a depth of 1/16 in. A hole of 3/8-in. diameter was drilled into the sealed slot at the center of the end face to serve as an entry port for the fracturing fluid. Existing fractures of various types were simulated in the models. A "hairline" fracture with essentially zero width was created by cutting the model into two parts with a diamond saw and replacing the two parts together along the cut. A finite-width fracture was created by placing a layer of sand grains between the two faces of the cut just described (see Fig. 12). A large open fracture (similar, perhaps, to a vug) was created by cutting the model in two parts and removing a portion of the downstream block to a depth of % in. See Fig. 13. For a fourth

By J. T. Norton, N. J. Grant, A. M. Gervais

An investigation of the creep deformation of coarse grained specimens of high purity aluminum in the temperature range 800&apos; to 1150°F, permitted the formulation of a theory explaining the formation of kink bands. The X-ray Laue back-reflection technique was used in conjunction with metallographic studies to determine the crystallographic elements involved in kinking and to measure the rotations of the bands. THAT metals deform by the formation of kink bands was first shown by Orowan1 in 1942. He manually compressed cadmium single-crystal wires, the basal planes of which were parallel to the wire axis and to the direction of compression. He found that kink bands formed quite suddenly. Similar experiments were performed by Hess and Barrett2 on zinc with a hydraulic testing machine to permit slower more careful compression. They observed that kink bands formed progressively with increasing compression. Recently Washburn and Parker3 observed the formation of kink bands in zinc single-crystal specimens during tension creep experiments. Each of these authors observed the formation of kink bands but did not make a complete analyses of the crystallographic relationships. In addition to these studies on hexagonal metals, extensive investigations of kink bands formed during deformation of aluminum in tension at room temperature have been reported. Two types of deformation bands have been observed during the deformation of aluminum at room temperature. These are: 1—kink bands: these exhibit a sharp curvature of the lattice along certain surfaces, and 2—bands formed by secondary slip along certain regions. As has already been shown by Honeycombe,4 it is important to point out the difference characterizing the two types of deformation bands. In the first case. for moderate deformation, only one system of slip planes normally is active; in the second case, however, two slip systems are active in the deformation bands. The latter have a rumpled surface because of the action of the two slip systems. In the present work only the first type of band was studied and to avoid any confusion the term kink band will be used exclusively in the discussion which follows. Honeycombe&apos; observed that very narrow kink bands (width, 0.01 mm) formed along the (110) planes during the deformation of high purity aluminum at room temperature. He observed narrower ones in commercially pure aluminum and found also that their width decreased with decreasing temperatures. Chen and Mathewson5 reported the formation of kink bands during tensile testing of single crystals of high purity aluminum at room temperature and pointed out that some rotation occurred about a [211] direction. The influence of the bending moment on the formation of kink bands was illustrated by the experiments of Rohm and Kochendorferl0 who used a Polanyi apparatus to obtain pure shear during tensile testing of high purity aluminum single crystals. Under such conditions only one slip system was active and no kink bands were observed; consequently, no noticeable asterism was detected after deformation. The influence of the bending moment will be discussed later. Calnan8 gave a detailed account of the work performed on kink bands obtained during deformation of aluminum at room temperature. Because no explanation of the process of kink band formation in creep was given in the previous investigations and because some of the above observations are vital to the following discussion the brief review of the literature has been given. It is proposed in the present work to provide an explanation of kink band formation during creep deformation at elevated temperatures. Results and Discussion Kink bands were observed to form during tensile creep testing of high purity (99.995 pct) aluminum specimens, having a very large grain size, in the temperature range 800" to 1150°F. These observations were made in grains which occupied the whole cross section of the specimen. The specimens were originally round (diameter, 0.187 in.; gage length, 1 in.) and had parallel flats milled to permit easier metallographic and X-ray observations. The final

Jan 1, 1954

By P. Chiotti, J. T. Mason

Thermal, X-ray, metallographic, and resistivity data were obtained to establish the phase diagram for the Yb-Zn system. Six intermetallic compounds and five eutectics have been identified. The compounds position at 695°C. No evidence for the compound YbZn,, was observed. Whether this compound is stabilized or inhibited by small amounts of impurities is uncertain. SEVERAL aspects of the Yb-Zn system have been reported in the literature. Much of this work deals with the crystallographic identification of some of the compounds. The YbZn compound has been reported by Iandelli and palenzonal and the YbZn, structure and thermal data for the composition range between YbZn and Yb3Znll have been reported by Michel et al. A compound of uncertain stoichiometry in the range 60 to 68 wt pct Zn with a cubic structure has been reported by Kuz&apos;ma et aL4 The YbzZn17, YbZn,,, and YbZn13 compounds have been reported by both Kuz&apos;ma et a1 and Iandelli and Palenzona.&apos; YbnZn17 has also been identified by Laube. This investigation was undertaken to establish the phase diagram of this system. Ytterbium in many respects behaves as an alkaline earth rather than a rare earth metal6 and it is of interest to note the resemblance between the Yb-Zn system, the Ca-Zn,&apos; and typical rare earth-zinc systems.g&apos;10 MATERIALS AND EXPERIMENTAL PROCEDURES The materials used in this investigation were Ames Laboratory ytterbium and Bunker-Hill slab zinc, 99.99 pct pure. Analyses of the ytterbium showed 38 ppm Ta, 82 ppm 0, and 15 ppm N with Ca, Cu, C, Mg, Al, Si, Cr, Fe, Ni, Sc, Y, Er, Tm, and Lu all less than 50 ppm. The ytterbium was dehydrogenated by heating in tantalum under vacuum for 8 hr at 900°C. The metal was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys in the composition range between ytterbium and Yb2Zn17. With higher zinc concentrations the tantalum was penetrated by the alloy and failed after several days at temperatures of 600" to 700°C. Approximately 20 g of zinc and ytterbium metal were sealed under argon in *-in.-diam tantalum cruci- bles equipped with thermocouple wells. The crucibles were in turn sealed in stainless-steel jackets. The alloys were equilibrated in an oscillating furnace and given various heat treatments in a soaking furnace. The steel jackets were removed and differential thermal analysis data were obtained under an atmosphere of argon. The thermal analysis apparatus was calibrated against the melting points of pure zinc, aluminum, silver, and copper and found to give thermal arrests within 1°C of the accepted melting temperatures for these elements. The thermal analysis apparatus has been described in an earlier paper.g Alloys were further heat-treated as necessary and subjected to metallographic examination and X-ray diffraction analysis. Most alloys were etched with Nital (0.5 to 10 pct nitric acid in alcohol). EXPERIMENTAL RESULTS The results of the thermal analysis are summarized by the points on the phase diagram, Fig. 1. Six compounds and five eutectics were observed. The eutectic temperature and compositions in weight percent zinc are 491°C and 12 pct, 645°C and 32 pct, 687°C and 54 pct, 742°C and 67 pct, and 750°C and 77 pct. The compounds YbZn, YbZn2, Yb2Zng, Yb2Zn17, and YbZnll melt congruently at 650°, 751°, 75Z°, 754", and 755"C, respectively. The compound Yb3Znll undergoes a peritectic decomposition at 695°C. The transformation and melting temperatures for the ytterbium were observed to be 797" and 817°C. re-

Jan 1, 1969