Search Documents

By Kay JR

In 1984 a new Regional Geological Mapping Program (RGMP) was commenced by the Geological Survey of Queensland (GSQ); the new program was in response to the withdrawal of the Bureau of Mineral Resources from regional mapping. Areas for mapping were selected in northern and south-eastern Queensland on the basis of potential for mineral discoveries, level of company interest, inaccuracies in the first edition mapping and interests of other organisations (government and universities) in joint projects.Geological provinces of particular interest in northern Queensland are the Hodgkinson Basin, parts of the Georgetown Inlier not covered by earlier BMR-GSQ mapping, Broken River Embayment, Burdekin Basin, Lolworth-Ravenswood Block, Campwyn Block and Anakie Inlier. The 1:250,000 sheets covering these areas of interest are shown in Figure 1 including those already completed, those in progress and those planned for future investigation.A flow chart showing the various phases for RGMP projects is shown in Figure 2. Data collection has two facets: (i) field recording and (ii) office work including air photo interpretation, study of company reports, literature research, petrography and various laboratory studies. Two main strands of information collected are represented by a data base and compilation sheets. Compilation sheets are generally at 1:25,000 scale and are available for purchase. The current data base is very fragmentary and can be accessed only by direct contact with the relevant geologist or via written reports. A more accessible field data base is in the process of being introduced this year; this field data base (REGMAP) is based on standardised data recording and computer storage.

Jan 1, 1986

By Laxaminarayan Holla

Significant coal reserves in New South Wales lie underneath major bodies of natural and stored surface waters. In order that mining can occur safely and without any adverse effect on the surface, various statutory provisions and administrative guidelines have been framed for regulating the surface and sub-surface strata disturbance. There are particular bases for the existing guidelines and the assumptions which were made in their choice. Evaluation of the guidelines in the light of the knowledge gained during the last ten years indicates that they are conservative in some cases and can be made less restrictive without lowering the safety standards. The suggested changes include reduced width for pillars in both bord and pillar first workings and panel and pillar workings, and increased level of extraction for a given degree of subsidence. Changes, if implemented, would lead to increased coal recovery.

Jan 1, 1987

By C Smith, J Cilliers, K Hadler

Unstable flotation froths, that burst before they overflow, produce no concentrate. Increasing the froth stability to improve recovery is therefore an obvious control strategy. Froth stability can be measured readily as the fraction of air entering the flotation cell that overflows as froth, rather than bursting on the surface; the ‘air recovery.’ Air rate is one of the most significant variables affecting froth stability. It is interesting that froth stability (air recovery) is maximised at a specific air rate, above or below which it decreases. It is important for metallurgists to realise that this maximum froth stability also produces the maximum mineral recovery, without compromising concentrate grade. Flotation cells must be operated at the air rate that produces the highest air recovery. The peak air recovery (PAR) to maximum mineral recovery relationship was first demonstrated by Hadler and Cilliers in 2009. Since then, the relationship between PAR and flotation performance has been widely explored; varying air rate, froth depth and particle size. Industrially, reducing the flotation bank air rate to achieve PAR yielded better mineral recoveries than other down-the-bank air rate profiles. In this paper, we present an overview of these key developments and findings in flotation optimisation based on PAR. Furthermore, using new industrial data, we show that PAR is not just applicable to rougher-scavenger cells, but also to flotation columns. Finally, we consider the future application of such an optimising control concept. CITATION:Smith, C, Hadler, K and Cilliers, J, 2018. Flotation control using froth stability: past, present and future, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 441–454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A M. Mueller

St Helena tunnel is the centrepiece of the Pacific Highway upgrade from Tintenbar to Ewingsdale, abbreviated and commonly known as T2E. At the deepest point the twin tunnels run 45 m below the ridge line of St Helena Hill, located about 5 km west of Byron Bay. The tunnel breakthrough was achieved early in 2014 and the works for permanent lining will be completed in early 2015.Once the project will be handed over to the public in 2015, T2E will deliver a safer highway and uninterrupted traffic flow between New South Wales and Queensland. The design speed in the project area has been set to 110 km/h by the client Roads and Maritime Services (RMS), which will reduce the travel times between Brisbane and Ballina to just over two hours.The two tubes of the tunnel have been designed to accommodate three lanes in each direction with shoulders and walkways on either side of the carriageway. These requirements result in a huge cross-section of about 20 m width and an excavated area of about 210 m2.With the tunnel alignment being situated in basaltic rock, St Helena tunnel is conventionally driven. The selected excavation method was predominantly drill-and-blast with temporary support being installed immediately after the excavation. Despite the wide span of the tunnel, the geology allowed the tunnel perimeter to be supported by only rock bolts and a layer of shotcrete over the majority of its length.Due to environmental reasons one of the approval criteria of the project was that the tunnel must not have a detrimental long-term impact on the groundwater system within St Helena Hill. Consequently the tunnel has been designed as a fully tanked structure with a waterproofing sheet membrane installed on the temporary shotcrete.The permanent structure of the tunnel has to meet a 100-year design life and it is designed as a cast in situ concrete lining. Considering the water pressure on the lining the concrete is reinforced with a significant amount of bar reinforcement.The presented paper provides a more detailed explanation of the geology and the consequential temporary and permanent support measures together with the waterproofing system.CITATION:Mueller, A M, 2014. Pacific Highway upgrade from Tintenbar to Ewingsdale (T2E), St Helena Tunnel, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 419–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By E P. O’Dwyer

Segment and gasket lining in tunnel boring machine (TBM) tunnels; and sheet membrane lining systems in driven tunnels are robust waterproofing systems each with a proven history of performance in Australia and further afield. Where an interface between these two systems occurs, the potential for costly failures is vastly increased and additional attention to detail is required in design, planning and construction. TBM cross-passages represent the most common occurrence of this interface, with steel compression flanges and neoprene gaskets being the typical means of connecting the waterproofing systems. There is a large variance in both detailing these flanges and associated outcomes, which makes this an area where there is room for improvement within the industry.The paper will look to tease out the various issues associated with this interface and how they can be dealt with efficiently with appropriate design measures, robust planning and carefully controlled construction methods.The paper will also look to review the new technologies and systems currently being put forward as potential alternatives, including an epoxy tape system, which has recently been successfully trialled on a project in Europe under high-pressure head.CITATION:O’Dwyer, E P, 2014. The challenge of waterproofing cross passages in segmentally lined tunnel boring machine tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Magnetic separation using particle rotation in a continuously rotating magnetic field offers very low to insignificant non-magnetic particle entrapment, and precise magnetic fractions. The precision of rotating magnetic field separations makes the method ideal for dry laboratory magnetic analysis work, where conventional laboratory magnetic separators can give misleading or uncertain data. The very low entrapment characteristics make the method ideal for entrapment-critical separations within the diamond exploration industry or in gold recovery. A single wet rotating magnetic field (RMF) unit is able to achieve a cleaner separation (at similar or better recovery rates) than a three-stage separation using conventional wet drum separators. The RMF separator is able to work effectively at particle sizes below 50 ¦m, and RMF separation could, at least in theory, be used down to single domain particle sizes. Rotating magnetic field (RMF) separation is carried out by magnetically spinning the particles at frequencies up to 300 Hz. The particle rotation itself may be used to roll the particles out of the separator. At angular velocities of 100 Hz, magnetic flocs are unable to form, and any entrapped particles are energetically expelled. In an RMF separator, the outer drum can be stationary while the inner magnet rotor rotates, allowing, for example, the injection of cleaning water underneath the separating magnetics to help remove small suspended non-magnetic particles.

Jan 1, 2000

By Heidecks C

Sub-level stoping with consolidated rockfill is the main method for mining steep dipping baryte and fluorite veins in Germany. Drifting is fully mechanised using drill jumbos, LHD units and shotcrete support. Stopes have heights up to 50 m with sub-level distances up to 15 m. Winning of the pillars between sub-levels is done by longhole blasting in slices of 3-5 m length on strike. Mucking is done on the lowermost level by LHD units. After each blast rockfill with binder (cement and/or fly ash) is dumped into the scope from the uppermost level. Economic success depends on both geological and technical parameters and factors, eg vein thickness and dip, ore grade, size and distance of sub-level drifts. Of particular influence are ore loss in pillar winning and dilution both in drifting on vein and in pillar mining. A comprehensive computer program has been developed for calculating the total cost per tonne run-of-mine ore respectively per tonne of concentrate for a single stope. The cost model includes development, longhole blasting, mucking and haulage to the mill, milling and ventilation. All costs (labour, energy, supplies, maintenance, depreciation and capital cost) are taken into account. Dilution and recovery are both considered. The program can be used to estimate the cost of mining a particular stope. It can also be used to investigate the influence of relevant parameters and factors on the economic result. By this way it should be possible to optimise the technical design of a stope.

Jan 1, 1995

By Gillies A. D S, Lee A. H

Water is an integral component of a mining operation. To-date water management has received a low profile in the overall management of mining operations. To cost effectively meet the requirements of government environmental legislation the man

Jan 1, 1994

By Roberts T, Firth B. A

A series of flotation experiments was carried out to study the interaction between the parameters of pulp density (mass per cent of solids in feed slurry) and frother addition (on the basis of solid mass feed rate). It was found that certain combinations of pulp density and frother additions caused large losses in yield. The interactive effect of these parameters can be primarily attributed to the total amount of frother added per unit of water. Consequently it is suggested that frother additions be made on the basis of water flow rate. As frother addition increased, in terms of the amount of frother per unit of water, yield increased rapidly but above an addition rate of about 10 g/tone it reached a plateau. Such results correlated well with qualitative visual observations of changes in bubble size and dispersion, with increasing levels of frother addition.

Jan 1, 1984

By T Ross, S Cameron

The requirement to use explosives in ground temperatures exceeding 50¦C is becoming more common as mines work to maximise the recovery of their resources. Orica Explosives was requested to assist in the development and implementation of æhot blastingÆ safe working procedures at Liddell Coal Open Cut in the Hunter Valley. The mine operator, Hunter Valley Earthmoving (HVE), had to contend not only with elevated temperatures in their overburden resulting from burning coal beneath, but also old underground workings which tended to exacerbate the problem. The paper discusses the following issues:the consultative process that was used to develop the procedures employed to ensure the process could be carried out safely; the technical issues surrounding blasting in hot ground, including temperature monitoring, product selection, application and design to ensure safety and performance were maintained; the need for confidence and trust in the team that was working together in a potentially hazardous environment, the emotive issues that were encountered and how they were addressed; the value of a regular review process combined with open and honest communication to ensure the procedures represented best practice and that all stakeholders understood the process; and the value delivered to Liddell Coal when sterilised areas of coal became accessible with little disruption to the mining process. The paper also discusses the challenges that were encountered in the Reservoir Block where proximity to major power lines and rail infrastructure meant that hot blasting procedures had to also consider vibration limits and the need for Energy Australia to disconnect the power.

Jan 1, 2001

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal. Investigations are in progress to develop a computer based scheduling tool capable of simulating the complex operating environment. A review of computer scheduling packages currently available within the State Electricity Commission of Victoria has found limitations making most unsuitable for the task. The type of package found to be most suited is a knowledge based system ('Expert System')capable of operating within a set of rules defined by the user. Work is proceeding on the development of a knowledge base to test the effectiveness of Personal Computer based `Expert Systems'.

Jan 1, 1989

By Mathew P. J

The CSIRO Division of Mineral and Process Engineering in Melbourne has been developing on-stream analysis sensors based on neutron and gamma radiation for better control of quality and process operations. This has resulted in the development of Ironscan, an on-stream analyser that measures the iron content of both lump and fine iron ore on conveyor belts. It can be mounted under existing conveyors with minimal modifications to the conveyor structure and can cope with steel cables in the belt. An interface gauge and an on-stream coal ash analyser have also been developed, both based on measurement of natural radioactivity. The interface gauge monitors the interface between liquor and mud in thickeners and washers, provided the natural radioactivity of the mud is sufficiently high to detect it above background. The natural-gamma ash gauge is a valuable addition to the Coalscan range of ash gauges. It is applicable to heavily laden coal conveyors or bins where the coal bed thickness exceeds 30 cm, and also to lightly laden conveyors, provided the coal is profiled on the conveyor.

Jan 1, 1991

By T Y. Ko, Y S. Kang, S J. Park, J H. Hwang

The lunar subsurface, particularly the lava tubes formed by ancient volcanic activity, presents a promising environment for establishing safe and sustainable human habitats on the Moon. Tunnel Boring Machines (TBMs), widely used for excavating tunnels on Earth, offer a potential solution for developing these subsurface spaces. However, the unique lunar conditions, including extreme temperatures, high vacuum, radiation, and the extraordinary strength and abrasiveness of lunar rocks, necessitate significant adaptations to existing TBM technology. This study investigates the feasibility of utilising TBMs for lunar subsurface exploration and base construction, addressing the challenges posed by the harsh lunar environment. We review previous conceptual designs for lunar TBMs, highlighting their strengths and limitations in addressing these challenges. Additionally, we explore innovative excavation methods, such as microwave-assisted rock weakening and undercutting techniques, to enhance the efficiency and effectiveness of lunar TBM operations. By evaluating the geological characteristics of the lunar crust and analysing the potential of lava tubes as launching points for TBM operations, this study provides a comprehensive assessment of the technical requirements and operational considerations for lunar TBM implementation. The findings of this research contribute to the growing body of knowledge on lunar base development and pave the way for future human exploration and utilisation of the Moon’s subsurface resources.

Sep 1, 2024

The difficulty in creating and obtaining a competitive edge in the mineral industry is rapidly increasing. The Kiruna Iron Ore Mine in the far north of Sweden is currently thriving on the world market through firm managerial strategy. LKAB believes in upgrading its raw material to produce a high quality iron ore product for sale to steelworks throughout the world. It is vital that this product is also of uniform quality and quantity to provide quality assurance to customers. The first link in meeting these product requirements starts in the underground workings. Mining methods and operations are of large-scale. Automation and continuous production streamline operations and reduce operating costs. These factors have built Kiruna Iron Ore Mine into the world's biggest, most modern, underground iron ore mine. To remain competitive on the world market, LKAB relies heavily on research and development. The mine is currently in a phase of upgrading its operations. A 25-tonne Toro electric loader is being tested to improve the rate of output of ore from the mine. Long hole drills are being improved to increase accuracy and efficiency. An electronic detonating system will improve detonator delay precision. Projects are underway to better understand ore flow mechanisms from a caving orebody. Benefits include improved ore recovery along with better rock quality control at the caving front. The continued updating of mining operations at Kiruna will enable LKAB to continue to maintain its competitive advantage on the world market in the production of high quality iron ore products.

Jan 1, 1997

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989.Previous drilling indicated over 100 million cubic metres of gravels with some 90% of the gold in the bottom 7 metres.The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below.Metallurgical studies and exploration were initiated when the project commenced; Leasing and environmental considerations were investigated and action taken.While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990

By Knight J. L, Baker G

The Wonthaggi coalfield is in South Gippsland, about 90 miles southeast of Melbourne. It is situated on the down-faulted block of the South Gippsland highlands that lies south of the Kongwak fault, between the Powlett River and the sea (Fig. 1). The coal, which is of Jurassic age, occurs in two small, and intensely faulted, limnic basins, that lie on either side of a concealed ridge of Silurian sediments. The coal was first found as thin seams outc1'opping in the cliffs at Cape Paterson, but the seams that are worked at Wonthaggi are concealed beneath a veneer of Cainozoic sands that covers the Jurassic strata, and were found by boring.The c9al seams are worked by the State Coal Mine, which was opened in 1909 to ensure a supply of coal for the Victorian railways, following a prolonged strike in the Newcastle field of New South Wales. The total production from 1910 to June, 1943, amounts to 13,918,800 long tons of coal. The coal seams are faulted to a degree unknown in most coal...

Jan 1, 1944

By R N. Humphries

The aim of this paper is to question the need to develop bespoke monitoring and assessment methodologies and criteria, thereby ‘reinventing the wheel’, when designing and assessing the success of important natural habitat and ecosystem restoration schemes at mine sites in the UK and Australia. It draws attention to the existence and applicability of the Phase I Habitat, National Vegetation Classification (NVC) and Condition Monitoring methods in the UK and similar approaches used in Australia. These are long accepted established methodologies and have published accounts for describing, assessing and managing natural vegetation communities, habitats and ecosystems. They are often used at the environmental impact stage, but seemingly rarely, if at all, in restoration design and management at mine closure. Their application to mine restoration and closure is illustrated and discussed by reference to a surface coalmine in South Wales, UK.It is concluded that the application of a combination of the Phase I Habitat, NVC and Condition Monitoring methods is highly relevant to the expectations of the Convention on Biological Diversity (CBD) and its implementation in the UK, and probably in Australia too. The methodology and criteria described could be incorporated into the guidance and specified in the mining permits so that there is clarity as to the expectations and requirements for monitoring and assessment for bond release. Their use could be of wider application where there is a requirement to assess the success of restored CBD assets and ecosystems.CITATION:Humphries, R N, 2014. Why reinvent the wheel when there are established methodologies to aid the design and assessment of restored natural ecosystems on mined land?, in Proceedings Life-of-Mine 2014 , pp 675–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Amusin BZ

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

By Gray N. B

The need to improve existing metallurgical processes and to develop new processes to meet the economic challenges that lie ahead requires the application of the tools of process analysis viz. mathematical models, physical models, pilot plants, laboratory measurements and plant tests. Examples of the application of these techniques to processes are described in this paper. Several of these techniques, combined with basic knowledge, are necessary to make improvements and for existing processes this always involves plant measurements. Also because metallurgical processes include extraction, refining, alloying, casting, mechanical working and heat treatment, an interdisciplinary approach to research and development is essential. This paper argues that metallurgical engineering is a discipline that is uniquely able to encompass the broad spectrum of chemical- and physical-metallurgy processes and is therefore essential to the health of the metallurgical industry.Regrettably many metallurgical engineering departments are not offering courses on process analysis, control, optimization, etc so necessary to meet modern industrial challenges.

Jan 1, 1985

By R Chinamatira

Several technical and economic factors have to be taken into consideration in developing an optimal mining method. This paper describes some of the important factors learnt during the evolution of the sublevel cave mining method at Trojan Nickel Mine, part of the Bindura Nickel Corporation (BNC) in Zimbabwe. Sublevel caving (SLC) has been successfully implemented at Trojan mine since its introduction in 1994. The method has evolved over the past six years into a system that has brought about improvements in efficiencies and productivity. Although the original design parameters used were sound and provided a solid foundation for the system, they needed to be optimised to get the best out of the mining method. Improvements and changes have been made in areas such as the drilling process, charging and blasting techniques, ring pattern design, development size and shape, and the draw control system. This has enabled the mine to develop an SLC operation that is efficient and innovative. Experience gained, together with the theory available has given us a much better understanding of the system. This knowledge will be used in the future to enhance the system further. Given the low grades of the BNC Mines, management recognises that only through technical excellence and efficient mining can the mines reduce mining costs and maintain profitability and competitiveness on the world market. In the Zimbabwe mining industry reaction to technological change, mechanisation and advancement have been relatively slow, due to isolation and economic constraints, compared to the rest of the world. Economic difficulties prevail, with high inflation levels, a poor exchange rate, lack of foreign currency and other associated problems. Despite these constraints, the bold steps taken have transformed Trojan mine into a more efficient and competitive operation, presenting itself as the leading mine in the BNC group. Appendices give data to illustrate the benefits obtained.

Jan 1, 2000