Search Documents

By Yambu J, Titus K

Geotechnical investictations and monitoring have been integral to development of the Porgera Gold Mine. The steep, unstable terrain has required a program for monitoring of slopes and foundations which includes survey stations, borehole inclinometers and piezometers. Case studies of the Maip Pass landslide, Yakatabari land-slide, Anawe Plant Site CIP pond excavation and batter, and a load test study for mine waste dumps are presented.Monitoring is needed to ensure that geotechnical risk is kept to a minimum. A vigilant program will be required for the life of the mine.

Jan 1, 1994

By G R. Hancock, M J. Saynor, J B. C Lowry, T J. Coulthard

Landform evolution models (LEMs) can assess the effectiveness of landform designs applied to a rehabilitated landform by predicting where erosion may occur. Here, we compare erosion predictions produced by the CAESAR-Lisflood LEM with field observations from the rehabilitated Pit 1 landform of the Ranger uranium mine, based in the Northern Territory, Australia (Figure 1). The ability to predict long-term erosion at a catchment scale is important, as the final rehabilitated Ranger landform is required to physically isolate buried tailings material for at least 10 000 years. CAESAR-Lisflood has been extensively tested and calibrated using data collected from erosion plots (0.09 ha) on the Ranger trial landform (TLF) for multiple years (Lowry et al, 2020; Saynor, Lowry and Boyden, 2019). However, until recently, it was impossible to compare model predictions with field observations for areas larger than the TLF erosion plots. We can now compare model predictions of Life of Mine Conference 2023 | Brisbane, Australia | 2–4 August 2023 116 gully development with field observations from the newly rehabilitated, 40 ha surface of Pit 1 over two contiguous one-year periods: 2020–2021 and 2021–2022. The aim of this study was to assess whether the CAESAR-Lisflood model can successfully predict gully erosion at a larger spatial scale.

Aug 2, 2023

By J Gould, T Elkington

Mine operation strategies are commonly optimised with a net present value (NPV) maximisation objective. There are well known properties of a typical mining project optimised for NPV, including high production rates and declining cut-off grade schedules. In practice, however, frequently there are operations that diverge from such NPV-maximising properties. Although a range of reasons for this can be at play, one possible explanation is that operators intuitively adjust their strategies to compensate for the flaws inherent to NPV maximisation. In particular, NPV analysis does not reflect the benefits of managerial flexibility inherent in a mining plan. Real options valuation (ROV) is an alternative approach that addresses this issue. We compare the properties of NPV and ROV optimisation solutions generated for the same scenario. Our simple case study demonstrates that the presence of real operating options in the optimisation model not only entails increased project value as expected, but also tends to encourage lower processing capacity (with lower associated capital cost), higher cut-off grades and greater use of stockpiles.CITATION:Elkington, T and Gould, J, 2012. Real option value optimisation, in Proceedings Project Evaluation 2012 , pp 35-40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

The discovery of nickel sulphide deposits at Kambalda in 1966 heralded the development of ò an industry with a capital value of over $1.5 billion producing about 10% of the western world's nickel. ò an unprecedented exploration boom in which over $200 mil- lion was expended in 10 years in the search for nickel deposits. ò a major new class of nickel deposits stimulating exploration for similar deposits overseas. and rapidly propelled a struggling small mining and exploration company to become one of Australia's corporate giants, provid- ing a much-needed stimulus to economic activity in a region suffering from a severe downturn in its principal industry, gold mining. Production of nickel in Western Australia commenced at Kam- balda in 1967 and grew rapidly to a rate of over 30,000 t of con- tained nickel per annum in 1970, 40,000 t in 1973 and 50,000 t in 1975. Early production was aided by a shortage of nickel on the world market due to disruption of supply from the major Canadian producers, resulting in high free market prices for the metal. Since these early years, the industry has experienced a number of cycles of indifferent health due principally to market developments overseas, although the level of production of nickel in Western Australia remained fairly consistent. The two most serious of these, in 1977-8 and 1985-6, forced the closure of a number of mines. Current nickel prices are allowing remaining producers to enjoy a measure of relative prosperity, although there is little general speculation that this will be long-lived. Nickel deposits discovered in the exploration boom were almost exclusively related to ultramafic rocks. Volcanic peridotite (komatiite)-associated deposits, exemplified by the Kambalda ore- bodies, were the targets of initial exploration which was concen- trated on ultramafic sequences near lower stratigraphic contacts with underlying mafic rocks. Subsequently, discoveries made in coarse-grained dunites in interpreted intrusive settings broadened the search parameters.

Jan 1, 1988

By N L. Turner, K Ehrig, V Liebezeit, D J. Robinson, L L. Kuhar, N Francis

Conventional industry tests used to determine leach recoveries are often fully monitored and may be time-consuming and expensive. Such tests may be limiting in geometallurgical applications where large numbers of samples are required to be processed for characterisation of an ore deposit. BHP Billiton currently use a fully instrumented leach test for characterisation of Olympic Dam uranium-rich samples. Researchers at the Commonwealth Scientific Research and Industrial Organisation (CSIRO) were approached to develop an alternative to these full-scale leach tests that could allow for the ranking of samples in terms of their leachability. The novel geometallurgical test was required to use samples of small mass and be affordable and rapid.Three leach test protocols were pursued in developing the small-scale tests. Kinetic leach tests were performed using mild conditions at higher pH, low temperature and low oxidation reduction potential, moderate conditions at intermediate pH, temperature and oxidation reduction potential and aggressive conditions at lower pH, higher temperature and higher reduction potential.This paper presents results from 44 leach tests on 11 samples with varying uranium mineralogy. The developed small-scale tests correlate well with data from the more costly conventional industry laboratory tests, indicating the possibility of using this alternative test as a geometallurgical leach proxy. Simple regression analysis confirmed the importance of pH, reduction potential and temperature on uranium extraction. Experimental data were fitted to published leach models to predict uranium leach extraction for a range of operating conditions.The ultimate aim of the test work is to combine a limited number of large-scale calibration tests, a large number of small-scale geometallurgical tests and leach models for geometallurgical sample characterisation and evaluation of a wide range of scenarios or processing options.CITATION:Turner, N L, Kuhar, L L, Francis, N, Liebezeit, V, Ehrig, K and Robinson, D J, 2013. Development and testing of a small-scale uranium leach for geometallurgical applications, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 345-350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Peck J. P, Kennedy D

Drill performance monitoring studies were recently completed at the Fording River mine, British Columbia. Microprocessor-based instrumen- tation and data analysis techniques were developed with the objective to improve short and long term mine planning. Data analysis permitted the identification of thicknesses and interfaces between soft/hard zones at depth based upon the recorded responses of the drill. Data clearly con- trast the soft coal seams and harder waste rock units based on variations in recorded drill rotary speed and torque, hydraulic downpressure, bail- ing air pressure and instantaneous rate of penetration. These parameters were monitored and recorded at 10 cm sampling intervals. Processed drill data was correlated with gamma logs, an existing means for locating coal seams and distinguishing between waste units. Current development of a pattern recognition module aims towards automated interpretation of drill data, identifying micro-and macro-geological and geomechanical rock mass characteristics. Delay between acquiring, processing and interpret- ing the drill data for practical use by mine personnel should be minimized. Integration of this technology with the mine's current main-frame based Mine Engineering Application System software will enable more accurate and timely annlication of the nrocessed drill data.

Jan 1, 1989

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

By Pietrobon M. C, Ralston J, Smart St C R

In an on-going study of the chemistry of base metal sulphide flotation, the effect of the inclusion of cyanide in the reagents suite has been studied, with special reference to ore from Pasminco Mining's Elura mine. Cyanide has been variously described as an iron sulphide depressant, a preventor of sphalerite activation and as an activator of galena. In the case described here, the cyanide appeared to act as an enhancer of the galena flotation performance, raising the lead recoveries by 25 per cent but leaving the sphalerite and pyrite responses unaffected. The lead rougher flotation performance with and without cyanide was investigated over a wide range of redox potentials (0 mV to 400 mV SHE). In all cases, the inclusion of the cyanide brought about an increase in the galena recovery and was responsible for a faster rate of galena flotation during the initial stages of the beneficiation. A surface characterisation study (XPS) of the lead flotation stage, with and without cyanide, indicated that the reagent interacted specifically with the galena and pyrite minerals. It was possible to correlate the surface absorption of the cyanide on the lead and iron sulphides with improvements to the flotation performance using the combination of surface spectroscopy and laboratory flotation Testwork.

Jan 1, 1991

By Flierman GA, Van Toor CH

Investigations were carried out of burden distribution using a full scale model of the furnace top. Various charging sequences were used and large differences were found between ore charged as sinter-pellets and as pellets-sinter. These were attributed to the differences in the angle of repose between the two materials. Permeability index was defined which was independent of the driving rate from which a furnace resistance index was obtained for use in weekly reports. Results are summarised as a single expression between blast rates and pressures and the values of Qbl and Qmax are continuously measured to aid the operators in controlling the wind rate in the safe AP region. Results also indicate a reserve in capacity of No. 7 BF.

Jan 1, 1975

By M A. Tuck

Atmospheric air on a moisture free volume basis consists of approximately 21 per cent oxygen. The current minimum threshold for oxygen in Australia is 19.5 per cent. Atmospheric air generally will also contain water vapour and will also pick up further moisture as it flows around a mine ventilation network. This paper details the results of a study to determine how much oxygen depletion can occur due to the sole impact of increasing the moisture content of air and the potential impacts of this on ventilation system design. The study shows that the moisture content can have a significant impact on the oxygen concentration in mine air. The main factors controlling the impact are the barometric pressure, dry bulb temperature and relative humidity of the air.CITATION:Tuck, M A, 2015. What is the oxygen depletion potential of ?water vapour?, in Proceedings The Australian Mine Ventilation Conference, pp 173–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Soma T

Pyrite and Cu-concentrate were roasted in vertically suspended state in an externally heated tube. Tubes of three different lengths of reaction zone were used for three different reaction times. Roasted ores were submitted to chemical analysis and the extent of roasting reactions was determined. In case of pyrite, extent of roasting reactions was not affected much by reactor length and heating temperature (above 500¦C), but was considerably by ore/air ratio. Micro- scopic and XMA examinations led to the conclus- ion that pyrite particles decomposed to pyrrho- tite and then pyrrhotite was oxidized to give Fe-S-0 melt, magnetite and hematite. The extent of reaction was not uniform in all particles but had a wide distribution from unreacted pyrite to completely oxidized particles. Combustion of Cu-concentrate from Kuroko complex sulfide ore ) was unstable under a uniform wall temperature of 450¦C, but proceed- ed rapidly at temperatures above 500¦C. Sticking of roasted ores to the wall of the reaction tube induced choking of the tube, caused by melting of roasted ores, at tempera- tures above 950¦C. Enrichment of oxygen exterted less influence on reaction rate than heating temperature of the tube. Particle size of ore had a big effect on reaction rate.

Jan 1, 1980

By K L. Olzard

At the WMC Resources Phosphate Hill operation, monitoring the quality of the ore delivered by the mine to the beneficiation plant is of prime importance to ensure the fertilizer is produced cost-effectively through the various stages of production and meets customer quality requirements. P2O5 and Fe2O3 are among the critical-to-quality elements. Fe2O3 is a key performance driver as it is an impurity that adversely impacts some of the chemical processes. The ore is supplied to the plant on a conveyor belt that is equipped with an automatic sampler. Increments are taken off the flowing ore stream at regular time intervals. A variographic experiment was conducted to investigate sampling strategies capable of estimating ore properties over a 12-hour shift to a nominated level of precision. The combination of individual increments into a shift composite was included among the strategies that were assessed. The experiment involved collecting data at regular time intervals and preparing variograms to characterise the feed-grade variability on the conveyor belt. Duplicates were also collected to assist in quantifying the precision of the subsampling stages of the sampling protocol and assay accuracy was monitored with matrix-matched standards. Various sampling schemes were evaluated by combining geostatistical techniques and the sampling theory of Pierre Gy. The following parameters were varied: the number of increments, the increment-size reduction leading to the composite, the masses of the subsequent sampling stages and the number of analytical determinations. This paper describes the planning of the variogram experiment, the various phases of data collection and the methodology used to process the data. It discusses the development of some of the sampling schemes that were considered.

Jan 1, 2005

By Nott M. C

The oxidation of xanthate collectors to xanthate/dixanthogen results in a higher hydrophobicity of sulphide minerals surfaces due to the action of dixanthogen. This higher hydrophobicity can be proved on a fundamental level by examining the st

Jan 1, 1994

By E R. Ramanaidou, M Wells

The aim of this paper is to summarise all known Phanerozoic ooidal ironstone deposits worldwide, including Australian deposits such as the well-known channel iron deposits (CID). Nearly 400 occurrences have been catalogued based on stratigraphy, geographical coordinates, facies, grade, tonnage and iron bearing ore minerals. The description also includes details on the geochemistry, genetic models and main references. Brief statistical analysis provides an overview of the variation between these deposits. This compilation offers a basis for better understanding of the ooidal ironstone deposits and a global evaluation of this important resource worldwide.

Jan 1, 2009

By F Hungerford

"In-seam drilling has been undertaken for the past 30 years for gas drainage to reduce the risk ofoutburst and lower the concentrations of seam gas in the underground ventilation. The drillingpractices have reflected the standards of the times and have evolved with the development oftechnology and equipment and the needs to provide a safe environment underground. Earlypractice was to adapt equipment from other fields, but with changing emphasis, research anddevelopment by the coal industry has created specifi c equipment, technology and practices toaccurately place in-seam boreholes to provide efficient and effective gas drainage."

Jun 1, 2012

By F J. van Zyl, C A. S Thomson

"Anglo American Thermal Coal conducted a high level study of all of its underground collieriesto determine if there were electrical power saving opportunities at the main fan stations.A systems approach to electrical power savings was used to identify potential savings in the various components of a primary ventilation system. Furthermore, only technological interventions were considered to obtain electrical power savings. From generic technological driven electrical power saving strategies four energy savings strategies were identifi ed, namely potential overall reduction in ventilation volume, improved underground air utilisation, optimisation of fan-set effi ciency and potential fan drift design optimisation. The study indicated the colliery (say Colliery D, Shaft A) that showed most potential in the four technology driven energy savings strategies. A detail study was undertaken at Colliery D, Shaft A to increase the confi dence level and the study confi rmed that up to 45 per cent of the main fan absorbed power can be saved (475 kW) with an estimated capital payback period of 18 months. The study clearly showed that an integrated approach to optimise the entire mine ventilation system has great potential for power saving, and that a clear, well -defi ned methodology will be applicable to similar underground collieries. This paper discusses the background to the study and the process followed to implement the energy savings initiative at Colliery D, Shaft A."

Jun 1, 2012

By E Bouchard March, F Lavoie, B Legare, K Bourassa

Quebec Iron Ore (QIO), a subsidiary of Champion Iron Limited (Champion), completed the restart of the Bloom Lake iron ore mine located in the heart of the Labrador Trough region of Northern Quebec, Canada in February 2018. Prior to its restart, the concentrator flow sheet underwent major upgrades which brought the iron recovery to the highest of all Labrador Trough operations. After two profitable years of production, QIO, supported by Soutex, started to look at technologies to improve its current performance and integrate into its expansion project flow sheet. From the lessons learned while optimising Phase 1, the addition of a scavenger-cleaner processing stage was identified as an improvement opportunity to increase recovery, produce a higher-grade product, and further improve the stability of concentrate quality. In 2019, the NI-43101 feasibility study for the Phase 2 expansion, aiming to double the production of high-grade iron ore concentrate, was published. Based on the metallurgical test work, the hydraulic classifier was selected to perform the scavenger-cleaning duty for its well-established performance and known behaviour at the cleaning step in the Phase 1 plant. To validate laboratory results, a pilot scavenger-cleaning hydraulic classifier was installed in Phase 1. Although the hydraulic classifier was selected for the feasibility study, metallurgical test work performed with the REFLUX® classifier showed interesting potential. It was thus decided to also install a pilot RC300 Reflux classifier at the scavenger-cleaning stage in Phase 1. Despite their apparent great similarities, the metallurgical performance was significantly different, and many dozens of sampling campaigns highlighted the different performance of both pieces of equipment considering the feed material particle size. This article presents the pilot plant results in terms of recovery, selectivity and stability for both the Reflux classifier and the hydraulic classifier operated in a scavenger-cleaner stage at the Bloom Lake iron ore concentrator.

Nov 8, 2021

By J Krnmmelbein, T Raab

In Lusatia, lignite mining causes major disturbances on the landscape scale. Reclamation procedures are applied to recover the reconstructed landscape for different land use options. In this study we investigate soil physical properties of an agricultural reclamation/recultivation site directly after site restoration and the development of selected parameters within the first years after site restoration depending on varying recultivation strategies.The sandy substrates used for recultivation stem from depths of several meters. They are unstructured, free of recent organic matter and have high contents of calcium carbonate. During reconstruction and most of all during surface levelling with heavy crawlers, the substrate?undergoes high mechanical stresses. This leads to partly severe soil or substrate compaction, depending amongst others on substrate water content and mechanical stresses during site construction. We investigate the effect of different organic soil amendments, different crop rotations and partly subsoiling on the development of soil structure. We compare results of laboratory measurements directly after site construction before any reclamation measures had been applied to results we gained after three and four years of recultivation. The results show that after the earthworks are completed, the site is strongly heterogeneous in relation to mechanical stability, permeability for air and water, pore volume and bulk density. The results after three and four years show that the heterogeneity of soil physical parameters decreases. The selection of suitable crop rotations superimposes the affects of other reclamation measures, eg varying organic fertilisers or deep loosening.CITATION:Krnmmelbein, J and Raab, T, 2012. Reclaimed lignite mining areas A73 in Lusatia - Development of soil physical parameters of an agricultural site within the first years after site reconstruction, in Proceedings Life-of-Mine 2012 , pp 117-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Howarth W. J, Sowerby B. D, Watt J. S

On-line analysis systems have found widespread application in the metalliferous mineral and coal industries. The continuous analysis and rapid response of these systems has led to improved control of mining, processing and blending operations, with increased recovery of valuable minerals and coal combustibles.The paper reviews developments in on-line analysis by CSIRO and Mineral Control Instrumentation Ltd which led to the award of the Australia Prize 1992. These commercialised systems analyse mineral and coal slurries; determine the ash and moisture contents of coal on conveyors, and the moisture content of coke on conveyors; and determine the carbon content of fly ash. These gauges are estimated to have resulted in productivity increases valued at $50 million per year to Australia.

Jan 1, 1993