Search Documents

By Little T. N

The Western Australian School of Mines is continuing to investigate the blasting techniques and mining strategies that are used for ore/waste separation (or high grade/low grade ore separation) or to prevent ore and waste mixing. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and undergoes no mixing of the various identified ore and waste blocks and is fully recovered at the minimum overall operating cost. The current study includes the use of computerised Knowledge Based Systems (KBS) technology to assist the user with the blast technique selection and blast design process. These aspects are highly dependent on the geology. (geometry, rock mass properties, grade distribution), explosive performance and the expectations of the mining company in terms of production rates and equipment utilisation. Most of these factors are not well defined and nor are they easy to quantify. However, a large amount of knowledge does exist and is available in the following forms: rules of thumb, empirical formulae, engineering judgement and past experience. KBS techniques are well adapted to handle such"forms of knowledge. The primary objective of this paper is to illustrate an approach for the use of Knowledge Based Systems during the analysis and interpretation stages of the blast design process. In particular, the components and methodology of the developed system are described for selective open pit gold mining. The Knowledge Based System developed was written using the declarative programming language PROLOG.

Jan 1, 1990

By J J. Cilliers

The aim of this paper is to give an overview of the FrothSim flotation simulator and to demonstrate its ability to predict the performance of real flotation circuits. Example simulations are presented in which the feed rate to the circuit is varied, followed by simulations in which a cleaner section and recycle loop are added to the rougher bank.The simulator is able to predict both the recovery and the grade produced by the cells at all locations in a circuit and the simulator is shown to produce plausible grade recovery curves. It also demonstrated that the performance of banks of cells improve as the feed rate to the bank increased (improved grade for a given recovery), but that more cells are required to give the same overall recovery.

Jan 1, 2005

The Mt Leyshon Volcanic Complex lies 24 kilometres south-west of Charters Towers and is part of a major continental volcano-plutonic province of Permo-Carboniferous age in north-east Queensland.The volcanic complex is located on the contact between Cape River Beds of Cambrian age and the Ordovician Ravenswood Granodiorite Complex. The emplacement of the complex appears to have been structurally controlled and is at the intersection of major north-east and minor north-west trending lineaments. The gold mineralisation occurs in the form of cavity coatings, matrix replacement, disseminations, and vein and fracture fillings containing quartz, chlorite, carbonate, pyrite, sphalerite, chalcopyrite and galena in various volcanic breccias and rhyolitic intrusives. The current published mineable ore reserves, calculated by Noranda Australia Limited, are 6.3 million tonnes of 1.8 grams per tonne gold and 4.8 grams per tonne silver. The orebody is open at depth, and in all directions except north where it abuts the granodiorite.

Jan 1, 1986

By Lunt D

Arsenic is classified chemically as a metalloid. That is, it has properties intermediate between those of metals and non-metals. Like non-metals, it combines with many metals to form arsenides (eg arsenopyrite FeAsS, niccolite NiAs, sperrylite PtAs2), but like metals it forms sulphides and oxides (eg realgar AsS, arsenolite As203). Arsenic is distributed widely in the Earth's crust at an average concentration of 1.5 mg/kg and is present in more than 150 minerals.

Jan 1, 1991

By Kametani H

Since pyrite is a semiconductor, the relationship between the leaching rate and the semiconducting properties is of interest. In order to investigate this relationship, a pyrite concentrate (95% FeS2) was oxidized at 90¦C (363 K) in an acid solution containing 100 g/dm3 H2SO4 and 1.0 to 25.1 g/dm3 total Fe. The suspension potential (Pt vs. SCE) was maintained at the desired values, within the range 0.40 to 0.70 V, by controlled additions of a KMn04 solution during leaching. The results were analyzed using a simplified kinetic expression. The rate constant was independent of the Fe concentration, while it increased with suspension potential. Partly oxidized samples were then prepared at varying fractions of reaction. After removing the elemental sulphur formed, they underwent thermoelectric power measurements using a packed bed lying in a temperature gradient. The value of thermo- electric power increased from about 0 to 30 pV/K in the early stages of oxidation. The results obtained are compared with those for chalco- pyrite reported in a previous paper.

Jan 1, 1987

The discovery of bauxite in 1955 at Weipa on the NW coast of Queensland's Cape York Pen- insula enabled Australia to join the Caribbean and West Africa as one of the major world sources of bauxite. Weipa, today, is the largest bauxite mining operation in the world and holds a significant position on the world bauxite scene as the operation 1. supplies 15 per cent of the Western World's metallurgical grade bauxite requirements, Z. produces 50 per cent of the world's demand for abrasive grade calcined bauxite, and 3. is the world's largest bauxite shipp ing port.

Jan 1, 1978

By Hodkinson I, Teale GS

Mount Leyshon is an open cut-heap leaching operation that commenced production in early 1987. Open pit reserves are 6.3 m.t. grading 1.8 g/t Au and 4.8 g/t Ag and expected annual production is 68,000 oz. of gold. Gold mineralisation is hosted in breccias, porphyry plugs and basement rocks interpreted as the roots of a multi-phase Permian phreatomagmatic breccia complex. Mineralisation has the form of veins, cavity fillings and disseminations and is localised by late stage trachytic dikes and sills and dike-like bodies of milled breccia in the northwest corner of the complex. The sequence of mineralisation includes: I quartz-chalcopyrite-molybdenite stockwork veins and pyrite-gold veins with potassic alteration II quartz-chlorite-carbonate-basemetal sulphide-gold veins and cavity fillings with sericitic alteration III quartz-basemetal sulphide-bismuth-sulphide -electrum veins, veinlets and dissemin- ations with sericitic alteration. Mineralisation is interpreted to have formed at 500-300¦C from a predominantly magmatic hydrothermal system related to the porphyry intrusive bodies. Mount Leyshon is a phreatomagmatic breccia with a very different origin to the Kidston magmatic hydrothermal breccia. However the mineralisation style and origin is quite similar.

Jan 1, 1987

By Z Li, D Chalmers, J M. Tenney

This paper presents the findings and analysis of the investigation of effectiveness of thin spray-on liners (TSLs) as a gas management tool in underground coalmines. The project involves spraying TSL on the area surrounding gas drainage holes whereby the TSL acts as a thin membrane decreasing the permeability of the coal. This restricts air migrating through the coal seam and diluting gas from the drainage holes. There are a number of potential benefits from this technique but key points are that gas drainage holes produce gas with higher concentrations of methane. The design and execution of a field trial to investigate the effectiveness of a TSL on purity of in situ methane from gas drainage holes is presented in this report. For eight drainage holes, the results show an average increase in methane purity by 9.14 per cent and a reduction in air contamination by an average 7.93 per cent. Overall methane flow rate decreased by 27.6 L/s; however, flow rates were unreliable due to poor measuring equipment. For most holes, methane purity was not changed significantly; however, certain boreholes were responsible for most of the variation in methane purity. The boreholes showing a dramatic improvement in methane purity were likely those with intersecting cleats covered by the TSL. If the TSL was sprayed over more area, specifically in areas where the cleats are intersecting with holes, it is likely that purity of methane in the drainage holes will increase.CITATION:Tenney, J M, Chalmers, D and Li, Z, 2015. Thin spray-on liners potential in reducing dilution of in situ gas in underground coalmines, in Proceedings The Australian Mine Ventilation Conference, pp 323–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

lbis new concept in geology is introduced by a reinteipretation of the Archaean stratigraphy of the greenstone belts of the Yilgarn Craton of Western Australia. Evidence is presented to show that the recorded Archaean succession of the Eastern Goldfields Province is composed of two distinct groups of mafic/ultrarnafic and felsic igneous rocks which, together with sediments, form alternating sequences represented by Cycles 1 to 4; Cycle 5 consists entirely of sediments. Recorded stratigraphy for the Murchison and corre1atives of the Southern Cross Subprovinces conform to this pattern. The five basic components are referred to as Unit 1 to Unit 5. A major erosional unconformity between Units 3 and 4 extending across the Craton is identified as a locus of potential major gold occurrence, including fossil placers, where suitable structural situations exist; Units 1 and 3 are identified as potential hosts of gold and nickel deposits; Units 2 and 4 for gold and base metals.

Jan 1, 1994

This paper presents a resume of the likely profitable mining areas in New Zealand. It covers the main "minerals" - gold, coal, oil and gas, ironsands, silica sands, clays, lump silica, perlite, sulphur and limestone.The potential mining projects are depicted on a map of New Zealand together with the associated works involved in hydro-electric and geothermal power development requirement for industries such as aluminium, nickel ferro-silicon or silicon carbide production.The political need for mining development to relieve unemployment and reverse emigration is stressed. A case is made for exploration and development assistance by government in labour re-training, energy supply and transportation, if the tremendous losses through lack of use of human and industrial resources are to be rapidly reduced. These losses are currently estimated at $10,000,000,000 per year.The need for protection of the sanctity of contract and security of tenure of all mining operations is touched on briefly as is the need for a reasonably balanced view on conservation. However as both of these are more properly covered in papers on the legal and environmental aspects of the mining climate they are presented here only as they affect the economy of the mining operation.Finally there is a brief comment on the mining climate in New Zealand relative to Australia and South Pacific mining operations.

Jan 1, 1990

By S J. Clarke, G Sieders

Double corrosion protection (DCP) rock bolts have evolved to become complicated assemblies comprising numerous components. This complexity is mainly associated with durability considerations including potential exposure to adverse groundwater conditions and ensuring separation of dissimilar metals within the bolt assembly itself.Recent progress in the construction of glass-fibre reinforced polymer (GRP) rock bolts have the potential to provide a viable alternative to conventional steel rock bolts in civil tunnelling applications. The durability of the material results in a much simpler bolt detail and permits the use of resin rather than solely cement based grouts.This paper presents the findings of the comparative structural testing of GRP bolts with conventional DCP steel bolts. The axial load performance, including stiffness, ultimate capacity and ductility of bolts are compared. Shear behaviour of bolts is considered, including durability issues associated with damage to the plastic sleeve used in DCP bolts.The paper also considers other issues which are relevant to the design of temporary and permanent rock bolts used in tunnel support, such as initial tensioning and grouting. Long-term performance, including durability and creep are also reviewed.CITATION:Clarke, S J and Sieders, G, 2014. Comparison of glass-fibre reinforced polymer rock bolts with double corrosion protection steel rock bolts for use in tunnel applications, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 237–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Moxon N. T, Berndt J. R

BHP-Utah Coal Limited's Peak Downs Mine is located in Cen- tral Queensland, approximately 200 km south west of Mackay. The annual raw coal production of the mine is over 8 million tpa, requiring the removal of about 40 million cubic metres of prime overburden. This is achieved through the use of five large draglines. The large depths of overburden (up to 55 metres) encountered over half the strike length of the mine enables cast blasting to be carried out in conjunction with draglines employ- ing the chopping method of digging. The objective of cast blast- ing is to use explosive energy to move as much material directly into spoil as possible. The additional costs of drilling and blast- ing are offset by reducing dragline rehandle. Two factors which are of primary importance to the design of cast blasts are initiation control and material velocity. High speed motion picture photography is a powerful diagnostic tool to quantify these aspects of blasting (Winzer, Montenyohl and Ritter, 1979; Chiappetta et al., 1983; Anon., 1983). The objec- tives of such analysis are to: 1. Determine the burden velocity, 2. Determine the time to initial movement (that is, the inter- val between a face hole firing and the initial movement of the burden), 3. Check the accuracy of the initiation sequence. BHP Central Research Laboratories (CRL) and Peak Downs Mine monitored a cast blast in the mine's Winchester Pit on 18 August, 1988. The objectives of this exercise were to: 1. Quantify current cast blast performance, providing a base case for comparison with modified blast design. 2. Compare two orientations of angled holes within the blast. 3. Assess the effectiveness of cast blasting utilising an air-deck. 4. Check blast timing with respect to burden movement times.

Jan 1, 1989

By A J. Daniels

Macraes Mine is a large-scale open-cut and underground gold mine located in Central Otago, on the South Island of New Zealand. This paper presents the role of geological mapping in the grade control process at Macraes Open Pit as a case study, and demonstrates how systematic geological mapping can add significant value to the mining cycle. Geological mapping has proved to be a valuable foundation for orebody interpretation and analysis.Practical applications and lessons learnt are summarised, including predictive control of the orebody, improvement of geotechnical modelling, and identification of further exploration targets.

Aug 22, 2011

The purpose of this paper is to discuss briefly the problems encountered in designing and sinking No 7 shaft, and to present the methods employed in the operation.The illustrations accompanying the paper show the details of the construction of the equipment used in completing No 7 shaft, consequently the descriptions appearing in the text are brief outlines only. Mineral leases Nos 7 and 8, held by the Broken Hill South Limited, comprise an area of 69.5 acres. The length of the holding is approximately 2500 ft.The western orebodies, which are the main producing masses, enter the property at the northern bonndary. Generally, the dip of the orebody is to the west, and the pitch to the south, but local variations occur and even a reversal of pitch has been noticed. The angle of dip is approximately 70 degrees and the angle of pitch 45 degrees.

Jan 1, 1932

FOR some time past keen interest has been shown in both America and South Africa in the mining drill-steel problem. This interest has extended to Australian mining fields, and Australian drill users, ever desirous of increasing efficiency, are vigorously attacking the problem. The writer has recently been engaged in the investigation of the problem on two of ,the biggest mining fields in Australia, and has formed very definite conclusions concerning the causes of many drill-steel casualties. He puts these views forward in the hope that they may be of interest to, both drill manufacturers and drill users. The subject is here dealt with mainly from the aspect of the properties of the steel and the modifications of these properties whensubjected to various manipulations. It is generally admitted that the drilling machine has greatly increased in power and efficiency during recent years, and the consequence is that the machine is demanding better service from the steel. This is being impressed on the drill users by an increase in steel casualties. This fact has led many mining people to the view that the machine has developed so rapidly that the steel maker has not been able to keep pace, and that consequently the steel isfailing by fatigue 0:1; so-called crystallization. This view is rather depressing. The writer, on the other hand, is inclined to discountenance fatigue as a serious factor under good normal working conditions where the steel is carefully manufactured and supplied to the user under suitable structural and sound conditions, and has subsequently received kind treatment at the hands of the drill sharpener and the drill user.It is not reasonable to attribute failures to fatigue until it has definitely been proved that the steel is fundamentally sound and is in the best structural condition to resist the stresses it is called upon to withstand, and, this being so, that all fundamental principles of...

Jan 1, 1923

Coal is a very versatile resource, having variable characteristics and having potential for a wide variety of mar- kets. Australia has extensive deposits of black coal, although they are concentrated mainly in Eastern Australia. Assessments of the currently known reserves are related to the qualities of these reserves. Markets available to black coal fall into the broad groupings of metallurgical, fuel, conversion and miscellaneous markets and the requirements of these markets are related to coal characteristics. Market trends in Australia and on the export market are discussed and projected forward. By the end of this century Australian consumption of black coal could well be 100 million tonnes per annum, and, in the absence of any export restriction, a similar amount is likely to be exported. Currently defined black coal resources in Australia will last at least 600 years at these projected rates of consumption. Although the position appears satisfactory in considering the projected life of the black coal resources, there is a serious lack of detailed information on reserves, mining and preparation yields, quality and possible environmental restrictions. Action is required on three parallel courses: (1) a consistent, systematic and extensive survey of current coal resources in Australia, (2) accelerated exploration activity to define poorly prospected and potential areas, and (3) regular updating and extension of the knowledge of Australia's coal resources. This information would be of tremendous assistance for the formulation of a national energy policy on coal.

Jan 1, 1975

Up to 80 per cent of the copper in a bornite ore can be quickly leached with percolating acidified ferric sulphate solutions. The upper limit for rapid copper extraction is set by the conversion of bornite to slowly dissolving chalcopyrite. The dissolution occurs in two stages: a rapid linear initial stage, followed by a slow, non-linear stage. The initial step is largely controlled by the rate of oxidant supply (Fe2(S04)3); temperature is not an important variable during the initial reaction. The second leaching stage is controlled by chemical and physical factors and is temperature dependent. The initial copper leaching rates are insensitive to both the concentration of the ferrous sulphate reaction product, and the sulphuric acid concentration.

Jan 1, 1973

By C Armstrong, B Wentzinger

Upstream embankment raises often represent the lowest cost option for increasing the capacity of tailings storage facilities (TSF), but also pose the highest stability risk due to constructing on top of previously deposited tailings.This paper presents an overview of key aspects in the geotechnical investigation and design of upstream raises and some recent lessons learnt from experience across a number of TSFs in Australia. A summary of recommended field investigation and laboratory testing methods is provided with a focus on collecting quality information for design purposes. A strong focus is given in developing an accurate assessment of pore water pressures, which, if not correctly understood can have disastrous consequences on tailings strength parameter interpretation and wall stability assessment in static and post-seismic conditions.The assessment of the contractive or dilative shearing behaviour of the tailings material and rigorous interpretation of design characteristic values are presented. Some comments on stability analysis options and proposed methodology are also provided.CITATION:Wentzinger, B and Armstrong, C, 2018. Lessons learnt in geotechnical investigation and stability analysis for upstream tailings storage facility raise design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 333–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Thomas G. A

THE irregularity of the Mount Morgan (Queensland) ore body presents problems other than those only of mining. For irregularity of outline is coupled with irregularity of grade, and the ore varies so rapidly from profitable to non-profitable, and fromhighly siliceous to highly pyritic, that the task of estimating quantities and values of ore reserves is manifestly rendered a difficult one, while the actual disposal of the broken ore demands constant supervision.Four classes of ore are handled. The oxidized ore, cheaply mined and cheaply treated, is obtained by quarrying from the top of the mountain. Below the 315-ft. mine level (measured from the original summit) sulphide ore comes in, and this is divided into siliceous sulphide ore (too siliceous for economic smelting), sulphide ore suitable for smelting, and ore too poor either to be smelted or to be treated by wet process with the siliceous ore. It is with these three latter descriptions of ore that this paper principally deals.Although the output from many stopes in the mine may usually be presumed beforehand to be either smelting or wet-treatment ore, yet it is never safe to take this for granted, and constant assaying is necessary. At the same time the ore merges from one class into...

Jan 1, 1911

By Colston M. B, Johnson I. D

The importance which matters of social welfare and environmental quality have assumed recently is the underlying theme of this paper. Demands for infrastructure reflect the change in emphasis from economic and technological development to those issues which affect the total well-being of the community. To put the importance of social change in perspective, examples are cited and a theme is developed which underlines the relevance of changes in public attitude and in government policies on mineral exploitation and related development and on the regimen of associated infrastructure sought. Planning on a long term or strategic basis and on a broad scale is put forward as an effective means of identifying changing social attitudes for the purpose of framing government and corporate policies. As a prelude to a section in which a description is given of a novel 'services baseline' concept and its use in the assessment of the current backlog of services

Jan 1, 1977