Search Documents

Mount Read is 'situated in the county of Montagu, on 'the west coast of Tasmania, about 20 miles inland from. Remine in an easterly direction, 15 miles northerly from Mount. Lyell, and 30 miles south-east from Mount Bischoff, and is one of the mountains forming the west coast range; it rises to a height of 3890 ft. above sea level.About eleven years ago the first mineral section was taken up on Mount Read by a Hobart company, known as the Mount Reid Silver Mining Company, consisting of 25,000 shares its holding consisted of one section of 80 acres, held under mineral lease. Prospecting was carried on for some months under great disadvantages, as all supplies had to be carried up the mount from Dundas, a distance of nine miles, on men's backs, until a pack track for horses was made.The track rises 2500 ft. in the first five miles, and then falls 200 ft. from that point to the mines, which are at an altitude of 3000 ft. above sea level, and at a point about two miles westward from the summit of the mountain, approximately midway between Mounts Read and Dundas.

Jan 1, 1901

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962

By Blaisdell J. L, MacPherson G

The present communication records the results of a research investigation conducted in the Porcupine Gold Mines in Timmins, Onto. Soon after silicosis became a compansable disease in Ontario under the Workmen's Compensation Act in 1926, the attention of mine operators and physicians was drawn sharply to the prevalence and importance of this condition in the mining industry. A number of examining centres were established in Northern Ontario by the Workmen's Compensation Board, and the yearly X-ray examination of miners was made compulsory.Although working conditions were soon improved, the mining industry realized that they were confronted by a problem demanding basic research for its final solution. The late Sir Frederick Banting had, for a number of years, been interested in silicosis, and it was upon his suggestion that an experimental investigation was undertaken at the McIntyre-Porcupine Mines Ltd., Schumacher, Ont., in November, 1932. A preliminary report of this investigation was published in 1937 by Denny, Robson and Irwin and a further report by the same authors in 1939.Accepting the theory that silica exerts its injurious effect upon animal tissue through a slow transformation into silicic acid in the presence of body fluids; these authors assumed that if the solubility of the silicious material retained in the lung could be sufficiently reduced, the usual fibrotic response would be modified or would not occur. A search was therefore undertaken for some non-toxic compound that would fulfil this purpose. After investigating ma:qy substances, Denny and Robson discovered in 1936 that the presence of small amounts of aluminum powder almost completely inhibited the solubility of silicious material in vitro. An intensive study of the mechanism involved later showed that the reduction in solubility was due chiefly to a coating of the silica particle with a thin film of a gelatinous hydrated alumina which on drying formed the crystalline alpha aluminum monohydrate boehmite (AI203.H20). The presence of this absorbed layer on the surface of the quartz was indicated by -staining it with aurin (ammonium salt of aurin tricarboxylic acid) and proved by Germer and Storks by means of electron diffraction patterns.Inhalation experiments with animals were at once begun, using pure quartz dust with and without aluminum powder. (See original communications.) These observers showed that while typical silicosis was produced in about 5 months in the control animals receiving silica dust alone, the...

Jan 1, 1945

Study on Separation Technology for Copper-Molybdenum Collective Concentrate

Sep 13, 2010

By Pullen G, Rose M

Continuing Professional Development (CPD) is not just a catch-cry. It is an essential component of every-day life in many professions, including accountancy, law and public administration. Without realising it, many other professions are undertaking CPD activities in an un-structured way, including mining, metallurgy and geology. Examples include Annual and technical conferences of The Institute, Branch-level technical meetings and in-company training and development programmes and technical exchanges. Whilst approaches to date have undoubtedly helped keep the Australian mining industry at the forefront of mining technology, one cannot presume that technological development will stand still. To meet this challenge, human resource development must keep pace, not only to optimize utilization of technological developments, but more importantly to develop firm bases from which new products, processes and technologies can be developed within Australia.

Jan 1, 1989

Six years ago it was my responsibility to give the presidential address, and now that privilege has come my way again. On that occasion we were gathered atWhyalla and I took the opportunity of putting before members some observations on the problems we then faced in Australia, and some gains we had been able to chalk up during those early postwar years. You may recall that we were then just beginning to emerge from the difficulties of postwar reconstructions - of fuel and power shortages, and a grossly inadequate manpower for the tasks facing us. The expansion of manufacturing industry in Australia greatly stimulated by wartime activities, and by the postwar developments of many institutions - ran ahead of the supporting services and of the supply of labour to do thejobs. For many industries this unfortunate state of affairs had meant operating at rates well below their installed capacities and therefore levels of output insufficient for Australia's rapidly growing needs. When I last spoke to you these problems were still with us, though their intensity was beginning to lessen as a result of vigorous efforts by industry and governments to reduce them. But I must confess that my thoughts on that occasion were full of those problems and of the effect they were having on the iron and steel industry of this country-of the coal shortage, the labour shortage, and the many other difficulties we were then faced with - and all at a time when the stepping up of our postwar expansion programme was of vital concern to all of us.What a different picture it is six years later! How greatly has the scene changed for the better. In 1951 Australia's postwar immigration programme was only in...

Jan 1, 1957

With the employment of a system of ore pillars to support the hanging wall during the mining operations at the North Mine, it was found that, when the stopes were worked out and the pillars remained intact, the main footwall drives developed an undulating longitudinal section due to the shrinkage of the filling in the worked out stopes.These depressions collected water, which made the footwall drives very wet under foot, and everitually worked its way into the pillar workings and the levels below.Water was also finding its way into the shafts because of the silting-up of the level drainage systems and, as both the shafts are down-cast, this tended to increase the humidity of the air entering the mine.To overcome these troubles it was decided to try a system of siphons as a method of subsidiary drainage.SYSTEM AT PRESENT IN USE.All drainage water is collected as near to its source as possible, run into a sump in an adjacent low lying part of the level, and continuously removed from these sumps by a siphon system.Each level has its own system. Water is collected from the sumps by a 1-in. pipe and delivered to a pipe running the length of the level along the back of the footwall drive. At the shaft the pipe is increased to...

Jan 1, 1938

The Beginnings of Mineral Processing Research in Canada - A Short Account

Sep 13, 2010

A pilot steel ladle injection facility designed to assist in the production of high quality steels suitable for use in pipelines has been built and commissioned at the Basic Oxygen Steelmaking (BOS) plant at Port Kembla Works.The plant design and the injection procedure are described.The performance of the unit and some metallurgical results are discussed in terms of the addition to the steel ladle of various quantities of calcium silicide and a lime based material. The effects of these additions on sulphur content and inclusion morphology and hence on steel ductility are also presented. The influence of ladle lining on desulphurisation is illustrated.On the basis of the experience gathered in the pilot plant a permanent and more sophisticated injection facility has been designed.

Jan 1, 1983

By W B. Edgar, I M. Platten, C A. J Towsey, B W. Cuffley

The evaluation of historical goldfields has been common over the past 15 years, reflecting changing economic conditions, improvements in knowledge and technology and lack of greenfield sites. Many goldfields comprise narrow gold-quartz veins, which are structurally complex with an irregular distribution of gold, have variable geometry and architecture and display late deformational effects. The study of historical mine records can be an important tool during early and advanced project evaluation, since it contributes to understanding the orebody, exploration target size and setting expectations. Mine records include documents such as plans, sections, reports, news cuttings, production tabulations, etc. A major advantage for the modern explorer is the capability of computer modelling to display this data in 3D. Historical records can give the explorer substantial information on various deposit characteristics, not least grade and geological continuity, geometry and architecture, mineralogy, metallurgical properties, bulk density and ground conditions. From an evaluation perspective, historical records can be used to support a Mineral Resource estimate, though its application will depend upon the quality and quantity of the data and judgement of the Competent Person. Effectively used, historical records can reduce geological uncertainty and focus evaluation efforts û thus reducing project risk.

Jan 1, 2009

When the mining and milling of 1100 copper orebody commenced at Mount Isa a satisfactory grade of copper concentrate was difficult to produce. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in inherently flotable fine pyrite and siliceous particles.The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1971

An extensive series of tests was carried out on a ball mill-rake classifier circuit in the New Broken Hill Consolidated Ltd. concentrator. The data were used to develop a mathematical model of the operation of a rake classifier and this model has been used in the simulation of the performance of a ball mill-rake classifier circuit on a digital computer. As a result of this simulation it has been possible to develop a technique for the optimization and control of a circuit which includes these units.

Jan 1, 1967

A process was developed, on a laboratory scale, for the removal of iron oxides from Weipa pisolitic bauxite. The technique involves the chemical reduction ofthe iron oxides by carbon, followed by selective removal of the iron species by acid leaching or chlorination.To remove more than 90 per cent of the iron it is necessary to reduce the iron oxides substantially to iron metal by heating the bauxite, pre-calcined at 650-800°C, with reactive carbon at 1040-1100°C. Reduction proceeds via the intermediate formation of hercynite (FeO.Al2O3) and difficulties have been encountered in reducing hercynite formed under less favourable reduction conditions.Following reduction, efficient selective removal of iron species is readily effected by acid leaching using dilute hydrochloric acid at 100°C, or chlorination at 500-750°C using Cl2, Cl2/N2, or Cl2/N2/CO mixtures.After removal of unreacted carbon, the final products contain 0·5-1.0 per cent Fe203 and 87-92 per cent Al203.

Jan 1, 1971

By Goldney L. H

The authors review the literature and discuss the application of methods to the design of thickeners for ilocculated metallurgical pulps. The use and evaluation of flocculents is described. Experimental data show that design based upon laboratory settlingdata is acceptable. The economic aspect of design is also discussed.INTRODUCTIONFor many years there has been little change in the methods for the design of thickener installations. While modifications have been made in the method of applying the data all methods have been based on the observee settling rate of the solids. The development of a theoretical approach based on physical data would involve so many variables which affect the settling rate that the more practical approach of direct observation seems unlikely to be replaced as the basis of design.The advent of synthetic fiocculents has introduced a modification in operation which affects design and should be considered. The authors review the subject and attempt to bring it up to date with present day procedure. Until recently the original work of Coe and Clevenger (1916) remained the basis of thickener design. They described their observation of the different zones encountered in settling, namely clarification, feed, transition, and compression or thickening- zones. The solids pass through the transition zone in settling from feed density to some higher density where settling ceases and ·some compression or compaction effect controls. the density obtained. The point at which the settling zone ceases to exist is known as the critical point.

Jan 1, 1959

By Orr C. W

In previous papers (1, 2), the influence on the creep resistance of elements normally found in commercial lead has been recorded. The results in the present paper refer to the influence of calcium, an element which is not found naturally in lead, but which has been used commercially in the form of alloys. It was realised that calcium would act as a deoxidising agent for lead-and in fact it was with this feature in view that both calcium and magnesium were used as additions. Subsequent work (including the results given in the present paper) has tended to diminish the importance which at first seemed to be associated with the presence of oxygen in lead. The structure of the dilute calcium lead alloys has been worked out in detail (S) and the phase diagram shows the existence of limited solid solubility and a compound CaPbs.

Jan 1, 1938

During the course of the major research in the Metallurgy Department of the University of Melbourne into the creep characteristics of lead and .its dilute alloys, it has been the practice to prepare the majority of test specimens from rolled strip. From time to time during the progress of the work, certain variables involved in. the rolling of the experimental ingots have been investigated. It is proposed to collect together in this paper the results of these experiments. Some general features relating to the type of deformation produced have been discussed in a previous paper.While it is admitted that the conditions prevailing through this work differ' in some respects from those of industrial rolling practice, it is felt that many of the factors investigated have an important practical significance. Some of the work described forms a continuation of the researches of R. S. Russell (2) , (3) , (4), into the recrystallization of various pure leads after deformation by rolling.MATERIALS USEDIn this work, a variety of "pure" leads and certain dilute alloys made from the purest of the basis leads have been studied. The compositions of the basis leads and the corres...

Jan 1, 1940

In, one stage of the purification sequence of the zinc sulphate electrolyte used at Risdon, cobalt is, precipitated as cobalt nitroso-,B-naphtholate, which is separated from the solution by filtration. Owing to the method of conducting the purification the filter cake contains much gypsum, unconsumed calcium hydroxide, basic zinc sulphate, and entrained zinc sulphate solution, Small amounts of iron and copper that have escaped previous purification steps are also precipitated with the cobalt as nitroso-,B-naphtholate. Thisprecipitate, normally carrying about 18% cobalt, is the raw material for the production of cobalt oxide, cobalt sulphate and cobalt metal.COBALT OXIDEThe main problem in the preparation of a reasonable grade of cobalt oxide from the filter cake is the economic separation ,of the cobalt nitroso-,B-naphtholate from the gypsum. This was solved by the application of flotation. It was discovered that the cobalt nitroso-,B-naphtholate, under correct conditions, would float without any addition agent, giving a relatively high grade concentrate. A plant, was built and has been in operation since 1936. The filter cake is pulped with water and pumped to one of two mechanically agitated tanks, eath capable of holding one day's output. Sulphuric acid is added until the free acid concentration reaches about 3 gm. per litre. Basic zinc sulphate is dissolved and calcium hydroxide converted to gypsum. The pulp, carrying about 2t lb. of solids per gallon, is pumped at a suitable rate to the first of a series of 10 flotation, boxes.. Each box is 3 ft. by 2 ft. 9 in. by 5 ft. deep, and, all have a common, pulp level, since the...

Jan 1, 1949

By Alvin J. F

Tin in ores containing 0·025 to 1·5 per cent tin can be determined polarographically by the reduction of the chlorostannite ion at the dropping mercury electrode in 2M hydrochloric acid solution containing 15 per cent ammonium chloride. The tin is separated from interfering elements by distillation as the tetrabromide and collected from the distillate by co-precipitation with aluminium hydroxide. The method can detect 0·01 per cent tin in ore.INTRODUCTIONAn iodimetric method, suitable for routine analysis of titrating tin in concentrations down to 1 per cent, has been available for some years (Low, Weinig, and Schoder, 1939).As concentrations fall below 1 per cent tin, there is increasing difficulty in obtaining a distinct end point due to large amounts of iron and silica normally present after fusion of the ore. Since concentrations of tin down to 0·02 per cent are significant in ore dressing products it was necessary to examine methods to determine such low concentrations, and to adapt these to tin ores containing a wide variety of other minerals.EXPERIMENTALDigestion and separationCassiterite, the principal tin mineral, is refractory but readily attacked by a sodium peroxide flux to yield soluble sodium stannate. In a recognized procedure, a sample of ore is mixed with up to 15 g of sodium peroxide in an iron crucible and swirled over the full heat of a Meker burner for 7 min. The fusion is leached with water and acidified.This solution then contains tin, silica, and other soluble...

Jan 1, 1962

The production of sulphuric acid at Port Pirie by the contact process began in March 1924 with the commissioning of the Electrolytic Zinc Co.'s roasting and acid plant. This plant, operated by B.H.A.S. Pty. Ltd. on behalf of the E.Z. Co., continued to produce sulphuric acid from the gases evolved when roasting Broken Hill zinc concentrate in mechanically rabbled furnaces until September 1954, when the plant was closed down.In this peri9d of approximately 30 years some 600,000 mono tons of 98·5 per cent sulphuric acid was produced, most of which was used for fertilizer production at Wallaroo and Port Adelaide. During World War II 14,400 mono tons of the above was produced in the form of 20 per cent Oleum and railed to the Salisbury Munitions Factory for use in the production of nitro-glycerine, gun-cotton and T.N.T.In the early post-war period various ways of converting at least some of the sulphur in the gases' discharged to atmosphere from the lead sintering plant were considered until, in 1949, it was decided to erect a modern contact acid plant. Much work remained to be done on the roasting plant to produce a gas of suitable grade for the contact process and also on the design of a purification section suitable for the treatment of D.L. gases.The acid section itself, however, was largely of conventional design and it was therefore decided that this would be erected first. To it was then attached a sulphur-burning section to allow it to operate as a "hot gas" brimstone acid plant until the roasting and gas purification plants had been designed and erected. In this way the urgent need for sulphuric acid in the fertilizer industry would be relieved, to some extent at least, as soon as, possible.

Jan 1, 1956

At the Orieco mine quartz veins carrying sulphides were localized in parts of an extensive fault zone in the Mathinna Beds during late Middle Palaeozoic mineralization.These deposits were subsequently exposed, and oxidation of the sulphides by percolating groundwaters resulted in the formation of gossans at the surface, and replacement close to the permanent water table of the more soluble sulphides by copper sulphides (chalcocite, coveIlite). A restricted zone containing copper oxides (cuprite, tenorite), copper carbonates (malachite, azurite), iron arsenates (scorodite, pharmacosiderite) and possibly rare copper sulphates occurred above the water table.The renewed oxidation of these deposits following mine development has been facilitated by the ready circulation of air and water combined with the formation of large free surfaces ideal for evaporation of aqueous solutions. Under these new conditions of high initial sulphate concentration, low pH, and relatively high Eh, the previously formed mineral assemblage is unstable and numerous Cu (Fe,Zn)-sulphates and Fe (Cu,Pb)-arsenates are presently forming in fractures in the fault zone and on the adit and stope surfaces for some considerable distance from the Sulphide-rich ore shoots. The observed spatial sequence of the major sulphates with respect to the sulphide-rich zones (Le. chalcanthite-antleritebrochantite and langite) is consistent with decreasing sulphate concentration and increasing pH away from the oxidizing sulphides.

Jan 1, 1970