Search Documents

By G Ferguson a, P Carrasco, P P. A Dowd

International codes of practice offer broad definitions with respect to the classification of resources in terms of risk. Specific guidelines and protocols, to analyse sample data, carry out geostatistical appraisals, develop geological models and finally estimate and classify resources, are not addressed. Neither are detailed requirements for engineering mineable reserves from estimated resources. In addition, international codes of practice fail to distinguish between types of deposit, other than in broad terms, as for example, The AusIMM JORC Code (JORC, 1999) which makes reference to diamond and coal deposits. The objective of this paper is therefore to set in motion the process of specifying detailed protocols, acceptable to the international community, for the assessment, reduction and management of risk associated with the development and extraction of mineral deposits. Ordinarily, the main risks and issues encountered during the process of estimating resources and subsequent conversion to reserves, encompass:failure to understand relevant geological controls of mineralisation; validation of grade interpolation; optimism in geotechnical appraisals of dilution and stability and the consequent selection of inappropriate mining methods; metallurgical modelling of minerals and contaminants reporting to concentrates; appraising the hydraulics of heap leaching and the numerous factors that can affect recovery; difficulty of managing metal price cycles and changes in regulations within the constraints of long-term mining plans; and development of better evaluation techniques for mining ventures. Uncertainty is inherent in estimation and engineering work, and its identification, reduction and management should be a fundamental goal of all involved in the mining industry (Figure 1). Variability may be reduced by:following internationally accepted practices for the collection, manipulation and analysis of geoscientific data; and verifying that the procedures actually performed meet the associated standards. Increasing amounts of data will also reduce uncertainty, but only if the procedures used to collect and appraise such data follow the relevant procedures. It is thus the aim of a series of papers in preparation, Beniscelli et al (in prep), to put forward detailed guidelines, for:project sponsors û to provide a global view of the work and documentation needed to support requests for funding various phases of project development and budget approvals; geologists û to indicate a checklist of the requirements and standards for the exploration and estimation of resources; and engineers and economic analysists û the protocols for characterising, modelling, engineering and evaluating the extraction of reserves. It is therefore hoped to encourage the development of consistent standards for declaring reserves within the mining industry. Data from projects and operations will be utilised to illustrate the benefits of adopting a rigorous approach to estimating resources and engineering reserves, Beniscelli et al (in prep).

Jan 1, 2000

By Schmidt LC

The method of supporting excavated roofs in underground coal mines by conventional roof bolting systems is challenged due to its shortcomings of being time-consuming and leading to possible unsafe installation. Though a few alternatives have been considered, the ultimate and most efficient bolting method has often been conceived as one using a self-drilling roof bolt, or a Rapid Face Bolting System (RFBS). The on-going Rapid Face Bolting Project undertaken by the University of Wollongong includes a special tubular bolt design.The tubular bolt designed for the RFBS is a "single-pass" bolt equipped with cutting tips used to drill a bolthole to accommodate the bolt. Different from that of the coring bit employed in geological site investigations, the principal design consideration for the tubular bolt is low cost associated with a small working life for the cutting tip.

Jan 1, 1991

By D M R Stone

Failings di,posal presents many challenges at metal mines in Peru where the extreme relief yields very little useable land area. These challenges are amplified by other hazards such as the high seismic environment, high rainfall, and frequent debris torrents down the steep hillsides. As a result many mining operations have resorted to in-river disposal of mill tailings. This paper presents a case history of one underground metal mine located in the high Andes mountains of Peru where in-river disposal of tailings has been used for some 30 years. The paper outlines a comprehensive engineering study that was aimed at increasing the utilisation of tailings disposal underground. The scope of this study included modifications to the grinding and flotation circuits to produce a high sulphide and low sulphide tailings for underground and surface disposal respectively: mapping and cataloguing of abandoned stopes for hackfilling: modifications to the existing backfill system to improve icliahility and throughput, and a preliminary evaluation of alternatives Such as silicated and paste fills.

Jan 1, 1998

In a previous study, various pyrite depressants were examined to improve the flotation performance of a copper-sulfide ore. Optimal results from this study were used to examine the effect of elevation on recovery and grade. Tests were conducted at elevations of 3350, 1735, 610 and -760 metres, consisted of five repetitive experiments for statistical analysis, and were performed both with and without airflow control. Tests were also performed in a glove box at Montana Tech to mimic the pressure conditions. Results indicate that both recovery and grade are dependent on pressure via bubble size and airflow suggesting that pressurised flotation cells should be considered for operations, particularly those at high elevation. Economics are extremely favourable for implementation because ensuing capital expenses are inconsequential with minimal time for return-on-investment.

Jan 1, 2005

By Seib W

In cut-and-break rock excavation use is made of the fact that breaking rock in tension towards a free face requires a specific energy of excavation which is small in comparison with that required for rock excavation using conventional tools operating by a process of indentation of the rock.The process of cut-and-break excavation comprises firstly a cutting step in which a groove is cut into the rock surface, followed by a breaking phase in which a tool is inserted into the cut in order to break the rock adjacent to the cut.

Jan 1, 1992

The information age has arrived. In every aspect of life, at the end of the second millennium, computers and information technology have made significant inroads. In mining there has been huge growth in the use of digitally controlled systems. From resource evaluation to mine planning to daily operations, information is being acquired, analysed, modeled and presented, using state-of-the-art information technology. Explosives, too, have moved into the information age. Computer controlled trucks and manufacturing plants have been developed and are now a regular feature on many mine benches. The next challenge for the explosives industry as a whole is to integrate blast initiation with information technology. The benefits are there, both to the supplier and to the end-user. Much has been written in the past about the potential for blast improvement but there are other significant advantages to a digital initiation system. These include security from unauthorised use, stock control and minimisation, reliability through testability and ease of use to name a few. So why is it taking so long? Surely the complexity of an electronic initiation system is far less than that of mobile phones that have been around for a long time. The answer, it seems, lies in the level of new technologies that need to be developed. There are enormous technological hurdles to be overcome in order to put into the market a cost-effective, reliable, user-friendly electronic initiation system. The most significant of these are:Safely and reliably initiating an explosive from an electronic device powered by a small capacitor. Prior to the development of electronic detonators primary initiation of explosives was by shock tube spit or by passing large currents and voltages down a pair of wires. Electronic detonators do not have that luxury. For example the energy stored in a æBeethovenÆ exploder is more than 500 times greater than that available to an electronic detonator. Communicating to a multitude of devices over very long cables installed by miners in harsh conditions. The deployment of an electronic detonator system has been likened to building a large telephone exchange in the rain and getting it to work perfectly first time! New communications protocols needed to be developed and tested. Wiring and connection systems have to be designed to survive the mining environment. In spite of these technological hurdles most of the major explosives manufacturers have persisted with electronic initiation systems and we are now, in 1999, starting to see the results of these multi-million dollar efforts. At SMI we are often asked many questions about this technology. The remainder of this paper seeks to answer those most often asked. As with any business linked to information technology todayÆs breaking news is tomorrowÆs archive and we expect the rate of development and understanding to accelerate as these technologies become accepted by the global mining industry.

Jan 1, 1999

By Noakes MJ, Willsteed TV

In the past few years an elevated gold price has resulted in the evaluation of many small scale surface gold deposits in Australia typically containing about 2-3 g/t Au. Operators have tended to assume that at the lower end of the grade spectrum only heap leaching is economically possible whereas above some assumed "cut-off" grade, carbon-in-pulp or similar techniques can be considered to have economic advantages.Studies made on a number of these prospects has indicated that this rather arbitary choice of treatment method can be mis-leading.A case study has been prepared assuming a "typical" situation and is presented. The deposit contains three million tonnes of ore assaying 3 g/t Au and is amenable to open pit mining methods. The mine site is remote but accessable and existing infrastructure is minimal. There are no unusual environmental constraints.

Jan 1, 1984

By Lewis RW, Tullemans FJ, Gallo JB

Gold mineralization at Kidston occurs in a semicontinuous zone near the margin of a large, late Palaeozoic breccia pipe. The pipe is ovoid in plan, funnel-shaped in cross section and straddles a contact between Proterozoic metamorphic and granitoid rocks which are intruded by a swarm of late Palaeozoic acid dykes. Rock fragments within the breccia pipe reflect the enclosing country rocks and mix in various proportions to form gradational lithological domains. Most of the gold is free and is located in the breccia matrix and in a set of inwardly dipping sheeted quartz veins which kink around the pipe margin. Sulphide minerals, dominantly pyrite, occur as disseminations in the breccia matrix and as aggregates in the cores of quartz veins. Hydrothermal altLration is pervasive within the breccia and is most intense in areas with the highest percentage of acid dyke fragments. Sericite and carbonate are the main alteration minerals. An empirically developed genetic theory for the formation of the breccia pipe and attendant mineralization involves magmatic and post-magmatic processes associated with the intrusion of a granitoid body to a shallow level in the crust. Economic evaluation of the deposit relied heavily on the results of diamond drilling. Both polygonal and geostatistical reserves were calculated and found to be in close agreement. Geostatistical reserves are considered to more closely reflect the tonnes and grade achievable during mining. Daily geological mine routine is strongly biased towards grade control allied with the practical aspects of open-pit mining. Tonnage/ grade correlations between ore blocks geostat- istically generated from exploration diamond core results and ore blocks generated from high

Jan 1, 1986

By J Hadjigeorgiou, T R. Stacey

A ground support system is a combination of individual reinforcement and surface support elements that work together to retain and contain the rock mass. The various elements are subjected to external loads and to interactive loading between individual ground support system components. This paper focuses on the challenges in determining the capacity and behaviour of mesh, recognizing that installed mesh can be subjected to several loading mechanisms. Field observations from underground hard rock mines demonstrate that there are multiple types of damage and modes of failure of mesh. However, these are difficult to reproduce in a laboratory environment. A critical review has shown that existing mesh laboratory testing rigs reproduce very limited loading conditions that may not be representative of underground conditions. This has significant implications in quantifying and extrapolating the performance of mesh to ground conditions. CITATION:Hadjigeorgiou, J and Stacey, T R, 2018. Challenges in determining the capacity of mesh, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 280–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Wauchope AMH

Arsenic residues from BHAS Refinery operations are currently treated to form a calcium arsenic compound and stored in lined dams on site. Laboratory and large scale work on these residues has resulted in the development of a hydrometallurgical process for production of arsenic trioxide. The process also recovers the material from the storage dams. The residues are hot water leached to produce an alkaline arsenic liquor. This liquor is mixed with material from the storage dams and lime to form a calcium arsenic precipitate. The precipitate is then reacted with sulphuric acid to form gypsum for return to the main plant, and an acidic arsenical solution. Metallurgical gas containing 3-6% sulphur dioxide is bubbled through the solution and on cooling arsenic trioxide is precipitated. The product contains in excess of 95% arsenic trioxide. Installation of a plant at Port Pirie based on this process is being evaluated by BRAS.

Jan 1, 1984

Oceana Gold CorporationÆs (OGC) Frasers underground (FRUG) transitioned into production in early 2008. The mine uses a relatively unique yielding pillars mining method that takes its lessons from empirical coal mining practices more so than hard rock techniques. Being a low-grade, flat-dipping resource hosted in the highly structured relatively weak Otago schist in central South Island in New Zealand, meant a number of iterations were undertaken to find the right mix of mining cost and resource extraction. Mining is on the down dip extension of the active Frasers open pit at the Macraes site (that extracts the full shear zone package at a head grade of 1.5 g/t). The challenges for the FRUG feasibility study team was to deliver an net present value (NPV) positive operation that would exist as a coproduct with OGCÆs other New Zealand operations, allowing it to make use of the high throughput low cost refractory ore treatment facility.Key factors in the successful project design were: Net capital costs kept to less than NZ$30 M by realising significant gold revenues from mine development from month four onwards. Virtually eliminating waste development by putting all key capital infrastructure in the low-grade ore adjacent to panels and maintaining the option of extracting this resource on retreat from the mine. Targeting a specific higher grade halo ore package within the entire mineralised shear zone. Applying a mining method that accepted a higher degree of dilution, ore loss and resource loss (in yielding and non-yielding pillars) to the flat-dipping resource. Thus providing an acceptable margin per tonne and resource tonnes mix, as the resource could not support a conventional low-cost caving operation, nor a higher cost room and pillar or open stope and backfill operation. 2008 has seen increasing tonnes and grade performance with a corresponding decrease in cost per tonne and cost per ounce as the mine has reached nominal capacity and is producing an operating surplus. The challenge will be to maintain and improve.

Jan 1, 2009

By B J. Andrew, M R. Daley

Mount Isa Copper Mines is a world-class mining operation producing approximately six million tonnes of ore per annum. With over 50 years of mining history and over 76 million tonnes of underground resource remaining there are many challenges facing the mine technical team today and into the future. The mine consists of nine distinct areas: the Hangingwall Lens, Footwall Lens, 1100, 1900, N1100, N1900, 3000, 3500 and N3500 orebodies. Each of these areas have different characteristics, requiring varying methods of mine design and ground control for safe and efficient orebody extraction. Each of the areas operate with an independent sequence whilst interacting with the entire underground operation. Within the first five years after graduating mining engineers tend to orient their careers in either a technical or operations direction. Engineers working towards a specialised technical career will often be working as mine planning engineers, whilst others more focused in the operations stream occupy roles such as operations or project engineers. At this stage of a mining engineerÆs career they are not yet categorised into one stream or another, but career decisions made now can generally focus their ultimate career path in one direction or the other. Due to the size of the Mount Isa operations there are many opportunities for engineers pursuing both career path and plenty of room for growth forthose as yet unsure.

Jan 1, 2005

By S D. Golding

The current study integrates hydrogeochemical and stable isotope results to investigate the sources and evolution of acid mine drainage at the historic Mount Morgan gold mine in Queensland, including the controlling factors and mechanisms of sulfate formation. The open pit and seepage sumps contain acid-sulfate waters and show elevated Al, Cu, Fe, Mn, Pb and Zn values. Samples collected from the Dee River bordering the mine site are less acidic, with lower concentrations of dissolved metals that gradually attenuate downstream from the mine. Concentrated acid mine waters has lead to formation of efflorescences consisting mainly of hydrous Fe-sulfates. The results of the ongoing isotope analyses on water samples show distinctive grouping of the data. The range of the sulfur isotope values for dissolved sulfate in samples from the open pit and sumps (d34S = 2.1 to 3.0 per mil) are similar to those of sulfides in the Main Pipe mineralisation (d34S = - 0.2 to 2.8 per mil). The lack of fractionation between sulfides and sulfate indicates that intermediate oxidation states of sulfur are not significant and makes this technique a useful tracer to identify the sources of sulfate. The Dee River samples, on the other hand, have heavier sulfur isotopes (d34S = 2.8 to 5.0 per mil). These samples may contain dissolved sulfate from æinternal sourcesÆ in the river basin, show local bacterial reduction or indicate a simple mixing trend. Further isotope analyses including oxygen isotopes of dissolved sulfates will enhance the interpretations.

Jan 1, 2003

By Grouhel P

Blasting performance is directly related to the characteristics and efficiency of the explosives used. The selection of the correct explosive for particular blast conditions and objectives depends on the ability to characterise the performance of individual explosive products. Techniques have been developed by the JKMRC to measure explosive performance and assess the impact of explosive performance on blast results. Studies conducted at a number of mine sites have shown that different types of explosives perform quite differently and that the performance of any particular explosive can vary significantly. The principal causes of these variations have been identified and detailed blast monitoring techniques, including the analysis of muckpile fragmentation and shape, have been used to quantify the effects of explosive performance on blast Results.

Jan 1, 1990

The energy input requirement to produce the molten slag associated with iron production to the modern Australian blast furnace, is estimated to be 2.OMJ/kg. In converting blast furnace slag to products of higher commercial value, advantage should be taken of this energy content by transporting molten slag from the furnace for beneficiation and processing in the molten state at an "off furnace site". The refined slag melt may then be converted into a variety of products for use in the building and construction industries, e.g. slag cement, slag sand and slag aggregates, insulation wool and various slag ceramic products. Some results of studies into slag melt beneficiation and conversion processes involving both molten and cold granular slag raw material, are presented.

Jan 1, 1979

By Sullivan T. D, Lohe E. M

Geological structure is one of the main controls on ground conditions within mining. It has a significant impact on the mining conditions and productivity of coal mines within the Sydney - Bowen Basin. The three main types of faults common to this region, normal, reverse and strike-slip systems, each present distinct challenges to mining. These systems effect a wide range of geotechnical and mining conditions within the mines. These include coal quality, strata stability, goat and caving behaviour, productivity and maintenance schedules of mining equipment, mine design and mine-site stress fields. A better understanding of the regional, local and mine-scale structural setting, timing relationships of structural events and the mechanisms of fault formation will greatly aid industry's push for greater productivity and competitiveness.

Jan 1, 1991

A series of physical tests have been conducted to determine the actual performance of bunton to shaft side wall connections typically used in new shaft construction in South Africa. The test set-up is described, together with the applied loading, which incorporates a cyclical load component and a quasi-static load component, in an attempt to simulate actual conditions in the shaft. The test results are given and it is shown that generally the performance is adequate, provided double-slotted holes are not used. Generally the fatigue performance is found to be good, with the only exception being cases where the bottom of the bunton is lower than the seating level for the bunton to side wall connection. Arising from the tests, typical design values of connection stiffness, strength and fatigue life are proposed and a design procedure including these three key aspects of connections is described.

Jan 1, 2005

The major technological advances of the last 30 years have profoundly reshaped mining practices. Machines keep getting bigger while productivity continues to increase and manning levels drop. These trends will continue and the introduction of breakthrough technologies will continue to accelerate, driven by a continued focus on lowering the cost of production, improving the productivity of workers and machines, and ensuring safer working environments. At the same time, global consolidation of mining companies has impacted on technology development in a range of ways. There are many potential technologies being proposed, some already operating in Australian mines. The automation of underground load-haul-dump (LHD) trucks for example, continues the process of removing workers from the most dangerous operating environments. Global positioning systems fitted to draglines, fibre optic communication channels, and 400 tonne trucks are only some examples of what lies ahead. However, where we need to return focus is to the technology of management û which is also one of the two key interrelated themes of this keynote address. Have we, as an industry, adequately been able to keep up with technological advances? Are our management systems as competent as the machinery we employ? The other key theme is the processes of globalisation and consolidation. What are the impacts on our industry? What are the implications of these processes, particularly for the ways in which we manage our people? My paper is divided into several components:some comments on the coal industry and the dramatic restructuring we have seen in recent years; in the context of this restructuring, an overview of my company and its evolution; my views on the role of contractors; some comments on the consolidation also occurring in the mining machinery and equipment, technology and services sectors; some observations on two major areas of technology û drill and blast; and trucks, shovels and excavators; the implications of consolidation and new technology for our employees and management; and finally some comments on research programs.

Jan 1, 2001

The aquifer at Phosphate Hill, north-west Queensland, presents special management challenges. The site contains a phosphate rock mine, fertilizer plant and camp. All of the site water is provided by the Duchess Embayment Aquifer, located within the Burke River Outlier of the Georgina Basin. The Duchess Embayment is a triangular shaped, Cambrian marine sedimentary basin consisting of siliceous and calcareous phosphorites, shales, siltstones and sandstones. It is fault-bounded on all sides and has a regional dip of 5¦E. The aquifer is largely confined to the siliceous facies of the Beetle Creek Formation. It has a very flat potentiometric surface and an average thickness of 45 m with confining beds above and below. The siliceous facies derives from weathering of the calcareous phase and is highly transmissive while the calcareous zone itself contains less water and is dependent upon interconnecting fractures for its permeability. Recharge appears to occur where the siliceous facies crops out around the edges of, and within, the Embayment. Aquifer management issues revolve around two points: successful dewatering of the orebody for mining; and efficient management to maintain water quality and ensure supply over the predicted 30-year life of the project. Current operations are extracting water at levels much below that originally estimated. This is having a detrimental effect on mine dewatering with the SWL lowering at a rate slower than anticipated. As a result, ore parcels are now beginning to intersect the water table, providing a major constraint to the mining plan. The aquifer drawdown cone is extensive and very flat so to keep the water table at an appropriate level for mining the management plan will include more aggressive dewatering to lower the level of the entire aquifer. The additional water will either be disposed of downstream or stored in a holding dam or via the use of artificial storage and recharge. Water resource management will also need to maintain the current quality. About 37 per cent of the water currently extracted forms the low chloride supply required by the ammonia plant and the power station. This ratio is expected to remain applicable under any future operating conditions but the low chloride resource is restricted so will require prudent management to enable the supply to continue. At current usage rates aquifer recharge versus use will need careful monitoring to ensure that the resource remains viable in the long-term.

Jan 1, 2003

By Blackwood R. L, Crichton G. P

In recent years, the value to Australia of the introduction of a system of resource rent taxation on the mining industry has been frequently debated. The forms that this rate of return based tax could take, and the impli- cations on government revenue and mining com- pany profitability have been discussed at some length. Further, the selective application of this taxation scheme to certain mining industry sectors has received considerable attention. This study takes the form of a survey of the taxation history of one significant Australian mining venture, the Mount Lyell Mining and Railway Company. The conditions faced by this company during its history are used as a base for the imposition of rent taxation schemes. Comparisons are drawn between the historical taxation liability of the company and that which would have been incurred if a resource rent form of taxation had been in existence. From the results of the study, it can be concluded that while the company can be con- sidered to have been a successful enterprise during most of its history, it has not achieved a level of profitability which would warrant the collection of any form of excess profits Tax.

Jan 1, 1979