Search Documents

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By D Osborne

Current mineral extraction and valorisation activities still have a strong focus on the ‘delivered product(s)’ which might be a bulk commodity such as metallurgical coal, hematite, bauxite, etc., and mineral concentrates such as metal sulphides, oxides, and carbonates; precious metals, such as gold, silver and PGMs, REEs or battery metals; halogen salt forming elements; or industrial minerals, which are non-metals including crushed rock, sand, and gravel etc. With the current focus on tailings disposal the pushback has been to seek alternatives to the currently ‘conventional’ disposal method via increasingly higher risk tailings settling facilities (TSFs) with a changing focus towards ‘dry disposal’. Whichever option is selected, the alarming trend is the increasing cost and ESG impacts. An emerging approach is to pose a focusing question ‘Is there anything else passing into the tailings stream and/or disposable waste streams which could be recovered and pass into the product revenue stream? All of the above ‘primary’ process streams offer opportunities for increasing recovery and offsetting some of the disposal costs. Some secondary opportunities are already being pursued, such as REEs and battery metals from base metals deposits, but other opportunities are still being overlooked, such as building materials and soil conditioning pellets. These potential ‘new’ product streams can also utilise other mining and domestic wastes such as smelting slags, glass waste, plastic waste etc. This paper will address these opportunities and provide examples including process approach, economics and some of the current barriers that exist, which are holding back progress on such initiatives.

Sep 1, 2024

By M A. Noppé

"Mining is an inherently risky business: from the technical, environmental, social and economic uncertainties associated with advancing an exploration concept to a viable project; to the risks associated with the operating, market, and safety risks and uncertainties attached to a developed mine; and the final mine closure process.Investors and other stakeholders assessing the risk, opportunity and relative value associated with a resource project need to appreciate the project in its correct context. Errors, omissions, biased reporting or conflicting information in reporting may result in a misinterpretation of technical and financial results, leading to biased estimates or assumptions on project value (Noppé, 2016).Simplistically, a project can be assessed on three key areas for positioning the project in its correct relative context, namely: the project development stage the confidence in the estimated quantities and qualities of the resource, reserve and/or product the level of accuracy, precision and confidence in the technical and economic studies supporting the project.In the latter case, the ‘technical and economic’ information includes assessing the necessary social, environmental and commercial/legal/governmental approvals for the project.Responsible management of a resource project through its full life cycle relies on competent and dependable control and direction being effectively provided by the technical, business and board leadership of the organisation. In turn, the project information must be effectively communicated between various disciplines, these disciplines and the company, and the company and its stakeholders.CITATION:Noppé, M A, 2016. Responsible management and transparent reporting across the project life cycle, in Proceedings Life-of-Mine 2016 Conference, pp 5–7 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By M Ma, W J. Bruckard, C Gontijo, R Holmes

Vale is the largest iron ore producer in the world. Since the 1970s, Vale has been using reverse cationic flotation to remove siliceous impurities from its iron ores. Whilst this flotation process has operated effectively for many years, it suffers from the problems of high reagent costs and high metal loss.In 2010, CSIRO investigated the use of a reverse anionic flotation process for Vale iron ore. Batch laboratory flotation studies conducted on Vale samples showed significantly reduced reagent costs and improved recovery of iron. In this work, the flotation behaviour of the different impurities in the Vale iron ore sample using reverse cationic and reverse anionic flotation processes is compared. Detailed flotation responses are presented and the merits of the two different flotation schemes are discussed.CITATION:Ma, M, Bruckard, W J, Holmes, R and Gontijo, C, 2013. Impurity removal in the reverse flotation of iron ore, in Proceedings Iron Ore 2013 , pp 427-430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By B Dold

"Mining has still today high potential for improvement in the exploitation efficiency. Especially low-grade ores have very low recoveries. In Cu bioleaching operations from porphyry copper deposits extraction of only five and 15 per cent with maximum of 40 per cent are reached. This means that 60–95 per cent of the resource is not exploited. Consequently, any metal not extracted will end up in the waste material, therefore increasing the risk of environmental pollution. This inefficiency is mainly due to the use of element concentrations for decision-making on the daily basis of a mining operation (eg cut-off ore grade, acid-base accounting – ABA). If, instead, quantitative mineralogical and geochemical data together with information on the bioleaching behaviour of the ore assemblage (the biogeometallurgical approach), is used for decision-making right from the beginning of the exploitation, higher recoveries and less environmental impact can be achieved, ie an increase in sustainability can be reached.CITATION:Dold, D, 2016. The Biogeometallurgical Approach – the Information We Need to Increase the Sustainability of Mining, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 169–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Process mineralogy is an inter-discipline in the fields of mineralogy and mineral processing. As a predicting and trouble-shooting tool, process mineralogy helps address all mineralogical issues and problems related to mineral processing. It provides useful information on process design and optimisation, flow sheet development and cost reduction. As more and more complex and refractory ores are being discovered and processed, it is believed that process mineralogy will gain more attention and play a more important role in process design and optimisation. This paper will first discuss the scope of process mineralogy and mineralogical factors that may affect mineral processing of various ores, and then focuses on the application of process mineralogy in process design and optimisation through case studies.

Jan 1, 2008

By A Satyanaga, H Rahardjo, K G. Mercer

The soil-water characteristic curve (SWCC) is one of the most essential soil properties in unsaturated soil mechanics. The water flow and storage characteristics of an unsaturated soil are closely related to the amount of water contained in the pores and the negative pore-water pressure in the soil. These are both in turn, related to the particle-size distribution and the plasticity of the soil. The SWCC is obtained by laboratory testing which is difficult to perform, costly and time consuming. There is a significant advantage in establishing typical SWCC envelopes for different soil types from a geotechnical design and analysis viewpoint. This paper presents some of the research work undertaken by UWA and NTU to develop SWCC envelopes for soil types classified in terms of the ASTM D2487 Unified Soil Classification System (USCS). This was done by establishing a large database of soils from across the world, classifying them according to ASTM D2487 and undertaking SWCC testing for each soil. This paper presents the SWCC test results from a selection of three of the most common soil classifications encountered in geotechnical engineering practise.CITATION:Mercer, K G, Rahardjo, H and Satyanaga, A, 2018. The development of soil water characteristic curves for soil types classified according to the USCS, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 263–273 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By G Reynolds, N A. Ware, L Lu

Queensland Pacific Metals (QPM) is progressing its Townsville Energy Chemicals Hub (TECH) project to produce nickel and cobalt sulfates for advanced battery materials. Apart from the nickel and cobalt sulfates, the process also generates a hematite by-product (~640 ktpa). The hematite byproduct precipitated from the process, hereafter ‘hematite precipitate’, is high in Fe and particularly low in impurities. However, it is a fine <20 μm crystalline, hydrometallurgical precipitate and is produced as a filter cake containing a high moisture content of about 15 per cent. This is considerably different from natural hematite ore and is expected to change its performance during sintering. In the present study, laboratory scale sintering tests were undertaken to evaluate the potential impacts of substitution of the hematite precipitate for traditional magnetite concentrates and further for Australian hematite-goethite ores in a simulated industry base blend. Substitution of hematite precipitate for magnetite concentrates was found to slightly increase the sintering temperature required to achieve the strength of laboratory sinters. However, further substitution of hematite precipitate for Australian hematite-goethite ores slightly reduced the sintering temperature required to achieve the laboratory sinter strength. These results reflect the reduction in Al2O3 contents of the blends and are consistent with the trend observed in industry and pilot scale facilities. The reduction in sintering temperature generally correlates to a reduction in fuel rate in the larger scale sintering process. The pore structure of selected laboratory sinters was further examined and discussed in conjunction with sinter strength. The pore structure images highlighted the relative difference between the blends with the most obvious difference being seen at 1290°C which correlates well with the laboratory tumble index (TI). The laboratory sinter samples showed an increase in porosity and irregularity of pore shape, as hematite substitution increased demonstrating the correlation between a more porous structure and a lower TI.

Sep 18, 2023

Rio Tinto Iron Ore is currently working towards finalising comprehensive Native Title land access agreements, which cover all of the current eleven mines and infrastructure owned and operated by the company in Western Australia&apos;s Pilbara region. Critically, the agreements represent a mutual commitment to a long-term relationship and address many areas of concern by promoting indigenous enterprise, well-being and regional development opportunities. Our objectives in the process are to obtain the informed consent of the traditional owners for our Pilbara expansions while providing benefits to them in a way which provides lasting and substantial improvements to health, education, housing and real jobs in the mainstream economy. &nbsp; To facilitate the agreement negotiations, Rio Tinto Iron Ore (RTIO) proceeded in 2005 to research and design a specific strategy around Aboriginal relations and local community engagement in the Pilbara. Wherever we operate, Rio Tinto follows a fairly simple formula in working with communities, which is comprehensively aligned to local context. &nbsp; This presentation provides an overview of Rio Tinto Iron Ore&apos;s community engagement strategy in Western Australia&apos;s Pilbara region. It will also explore the establishment of regional standards on employment, business development and contracting that have been developed to ensure Indigenous people are engaged in the development of their region and are able to contribute to supporting the growth and development of mining in the area with the expectation that there is prosperity for all. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

By C Wu, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The Halasu porphyry copper belt, located in the East Junggar basin bounded by Chinese Altay to the north and the Tianshan mountains to the south in the Central Asian Orogenic Belt, is one of the major porphyry copper belts in Xinjiang province, north-west China. Combined with previous studies in this area, the magmatism can be divided into three periods: pre-mineralisation activity of 390 Ma syn-mineralisation activity of 380–370 Ma post-mineralisation activity of 360–330 Ma.Through the comparison of zircon chemistry from ore-bearing and barren syn-mineralisation intrusions, negative correlation was identified between Ti-in-zircon temperatures and oxygen fugacity, corresponding to the fact that late-stage syn-mineralisation granitoids contain high water content, high oxygen fugacity and low temperatures with higher mineralisation potential. In addition, the relative low initial 87Sr/86Sr ratios, high eHf(t) and eNd(t) values and mantle Pb isotope characteristics in this study support that the magma forming these intrusions was probably derived from juvenile crust generated during subduction-accretionary processes.CITATION:Wu, C and Chen, H, 2015. Zircon trace elements and Sr-Nd-Pb-Hf isotope systematic of the Halasu porphyry Cu belt, north-east Xinjiang, China, in Proceedings PACRIM 2015 Congress, pp 637–640 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By G Reynolds, L Lu

Queensland Pacific Metals (QPM) is developing its flagship Townsville Energy Chemicals Hub (TECH) facility to produce nickel and cobalt sulfates from imported high-grade nickel laterite ore for nickel-cobalt-aluminium and nickel-cobalt-manganese Li-ion batteries. The TECH facility is expected to use a patented leaching, recovery and recycling process called the DNi Process™. It uses the nitric acid leaching process for extracting nickel, cobalt and other valuable metals from laterite ore. Apart from the nickel and cobalt sulfates, the TECH Project will also produce high purity alumina, hematite (~640 ktpa) and other by-products. The hematite by-product precipitated from the DNi Process™ (hematite precipitate hereafter), is high in Fe and particularly low in impurities. QPM is working to identify potential applications for these high-purity by-products to generate additional revenue and to achieve its zero-waste ambition. As such, QPM has engaged CSIRO to evaluate various agglomeration options to produce low-cost, hematitic products suitable as ironmaking feed materials. This paper will first reveal the unique characteristics of the hematite precipitate arising from the TECH Project and then examine the sintering and pelletising processes for preparing the hematite precipitate as an ironmaking feed.

Sep 18, 2023

By S Sullivan

The key skills for a competent geologist are observation, documentation, analytical thought and the ability to communicate. These attributes have served the geological world for the past two centuries since the field of geology was separated out from natural philosophy. The understanding of the structural setting, lithologies, alteration and 3D distribution of the target mineral species are essential precursors to resource evaluation and potential economic extraction. The advent of artificial intelligence and machine learning has matured to the point where observation by dedicated sensors and analysis by customised AI algorithms can replace manual processes and deliver credible results. In combination with analytical data such as assays, various sensors now collect physical properties of rocks which are used as proxies for mineral identification and rock mass classification. These sensors include X-ray and infra-red spectra, magnetic susceptibility, gravity/density, EH/pH measurements, conductivity, colourimetric readings, porosity, fracturing and fracture intensity. Analysis using machine learning techniques trained using known data sets can determine rock type classification, rock density, quantification of grade/quality attributes, mineral alteration, weathering and geotechnical attributes such as rock quality. This type of data relies on calibration and quality control of a variety of different types of electronic hardware. The resulting data is non-additive, has error ranges and will be suitable for consumption by fast AI methods providing probabilistic analysis. A second stage could include geometallurgical constraints to provide an ‘extractability index’, which is of more interest to miners than pure geotyping. Using resultant interpreted geological criteria, 3D domain models with spatial attributes will be built.

Sep 1, 2024

By C Sylvestre

For the last 50 years, traditional safety management has improved safety performance by: • Fixing the environment (eliminating the hazard). • Improving the system (more/less rules, procedures etc). • Making safety more conscious (more/better interactions about the importance of safety). Although these approaches certainly have merit, and may be part of an overall solution, they are not enough to prevent many modern-day incidents. Today, these three approaches are used more than before, and are used better than ever before. Yet, workplace fatalities in Australia have stagnated from 2013 to 2019, as have the number of incidents, even serious ones. In the USA, workplace fatalities have increased by 15 per cent in the same period.

May 5, 2022

By S Jeon, K Haga, A Shibayama, L Godirilwe, C B. Tabelin, I Park, A Buronov

Open pit/underground mining and mineral processing can generate large amounts of waste that contains sulfide-type minerals such as pyrite (FeS2), and it can produce acid mine drainage (AMD) when exposed to oxygen and water. This highly acidic wastewater contains heavy metals and this is one of the most serious environmental issues after mining operations taking several decades to completely remediate with high costs. For green mining, the present study focused on the development of a recovery technique for gold from an eco-friendly solvent, thiosulfate, by utilising mine wastes, tailings. First, gold recovery experiments in ammonium thiosulfate system were carried out using model samples representatively present in tailings (ie SiO2, Al2O3, FeS2, Fe2O3, and Fe3O4). The results showed that gold recoveries were negligible when using Al2O3, SiO2, Fe2O3, and Fe3O4 while pyrite shows a recovery efficiency three-fold as high as the maximum recovery efficiency when using others. Subsequently, the study also addressed the identification of the recovery mechanisms and post-recover process. The results indicate that tailings can be sufficiently utilised for gold recovery in the hydrometallurgy process and a further sustainable process can be established.

Sep 1, 2024

The purpose of this study was to investigate the effectiveness of froth fl otation for the recovery of gold from the gravity tailing stream of the former Lihir Gold Limited (LGL) operation in Ballarat. The P80 of the tailings was determined by screen analysis as 1 mm, with test work conducted on as received material along with samples ground to P80 sizes of 47, 78 and 134 microns. Laboratory scale batch flotation tests were conducted at both natural and elevated pH to investigate the impact of pyrite depression on gold recovery. Results indicated that although an increase in grade from approximately 0.7 g/t to 3 g/t was achievable at a natural pH and a P80 of 134 micron, gold recovery was low at just 35 per cent. Finer grind sizes were found to have an adverse effect on both grade and recovery. Future efforts will be focused on the sub 310 micron size fraction of the tailings, which was revealed to contain approximately 85 per cent of the available gold and may be amenable to cyanidation or ultra-fine gravity treatment.

Aug 1, 2010

By Fazakerley VW

The Murrin Murrin deposit is located about 210 km NNE of Kalgoorlie and 50 km E of Leonora in the North Eastern Goldfields region of Western Australia at latitude 28¦ 50&apos;S. longitude 121¦ 54&apos;E on the Laverton (SH 51-2) 1:250 000 map sheet. The tenements are held by Anaconda Nickel NL. Geological investigations between 1994 and 1996 resulted in resource calculations being completed for the ten lateritic nickel cobalt deposits shown in Figure 1. At a 0.8 per cent nickel cut-off the resources at May 1996 for the nine deposits are 116.8 Mt at 1.10 per cent nickel and 0.082 per cent cobalt. The nickel-cobalt mineralisation is contained in a laterite profile developed over Archaean serpentinised peridotites. A bankable feasibility study has been completed and the project is scheduled to be in production by the beginning of 1998.

Jan 1, 1996

By F F. Pitard

Observation from attending many conferences around the world reveals that many people are constantly shifting from the word ‘error’ to the word ‘uncertainty’ without a clear vision of what the subtle difference is. The same applies to a large swath of the scientific literature, in which these two concepts are unfortunately often used synonymously, which is a scientific flaw of the first order. In practice, as demonstrated in the Theory of Sampling (TOS), there are both sampling errors and sampling uncertainties. Sampling errors can easily be preventively minimised, while sampling uncertainty for a preselected sampling protocol is inevitable. P M Gy’s work, supported by G Matheron’s critical reviews, demonstrates beyond any possible doubt that sampling uncertainty cannot be achieved if sampling errors are not preventively minimised by applying very stringent rules that are too often ignored by sampling practitioners. A clarification, in line with the TOS, is presented to mitigate the confusion created by circles favouring the use of uncertainty versus the use of the word error. Both words are very different in nature and scope and they are both necessary in their due place and time.CITATION:Pitard, F F, 2017. From errors to uncertainty – a clarification for proper use by the Theory of Sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 355–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By D Stacey, J Matthews

Hunter Valley Operations in partnership with Orica Explosives designed a process to optimise coal extraction at depths greater than 65 m below the Hunter River in a safe and cost effective manner. The process involved a team approach to investigate the relationship between geology, mining sequence, vibration and blasting methods adopted. From this an optimum method for uncovering the coal was developed.

Jan 1, 2001

By R deMoraes, A Bobet

The last decade has seen a resurgence of interest in lunar exploration and the emergence of countries like China and India as space fairing nations. In 2004, the US announced a new Vision for Space Exploration, whose objectives focused on human missions to the Moon and then Mars. The near future is likely to see the emergence of a worldwide drive to revisit the Moon as the first step in investigating the Solar System. To date, the Apollo missions provide our only experience of human operations on the Moon or anywhere else beyond Low Earth Orbit. Much was learned from these missions. However, their short duration means that many of the environmental effects that will be important for longer-duration missions could not be quantified. In addition, long-duration missions and infrastructure on the Moon require new technologies and capabilities, which must operate successfully and reliably in this lunar environment. Developing these technologies poses significant challenges for the exploration program. The paper discusses the risks associated with the construction of lunar surface and underground structures and the challenges to adopting the standards and rock mass classification systems developed on Earth and their applicability to the Moon. Moreover, an exchange of views to explore near-surface geologic and geotechnical profiles of the Moon is emphasized and implications of the lack of knowledge on rock mass characterisation of the Moonrock mass, the lack of theoretical/empirical experience on the use of rock mass systems outside Earth, and uncertainties.

Nov 29, 2022

By A Mackay

As a result of the explosion in the 512 panel at the Moura No 2 mine in 1994 the role of the ventilation officer (VO) to submit sealing plans (on behalf of the operator/underground mine manager) has become one of the key duties of the VO of an underground coal mine in Australia. The intent of a sealing plan is to document the controls used to manage the build up of flammable concentrations of gases, and for these controls to be reviewed by the industry regulators. These sealing plans have brought a large amount of focus onto the sealing process and served the industry well. The legislation does not define sealing, or when it begins, but throughout the industry typically sealing plans are submitted 30 days prior to the last seal being constructed. This practice appears to have originated from the Moura 512 panel being a standing bord and pillar panel and where the explosive gas mixture could only occur after it was sealed. However, since the Moura disaster the industry has become dominated by goafing style longwall mining. Goafing panels differ from standing bord and pillar panels in that they typically have an unventilated goaf that can potentially contain an explosive mixture from start-up. This was recently highlighted by the explosion and fire on Longwall No 1 Tailgate at the Blakefield South Mine in 2011. The author ponders whether the industry should revisit sealing plans to focus on the core hazard and define that sealing begins when flammable concentrations of gases are created. Although defining when mine sealing begins is the key outcome of this paper, the main point is that VOs and industry regulators need to clearly understand what can occur in the atmosphere of underground coal mines. CITATION:Mackay, A, 2013. A case for change - Defining mine sealing and understanding flammable mixtures during sealing, in Proceedings The Australian Mine Ventilation Conference , pp 307-310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013