Search Documents

Cable bolts have been used extensively in the development of the footwall of the Mt Whaleback Mine as a part of the ground improvement program since 1986. High tensile seven wire stress relieved steel strand similar to that used in pre-stressed concrete and grouted in place with sulphate resistant cement have been employed for rock-mass reinforcement.Most of the footwall is developed in Mt McRae Shale which contains a 20 m thick pyritic shale layer 14 m below the ore/waste contact. Due to extensive folding of the footwall rocks, the pyritic shale layer regularly occurs on, or close to the pit slope. Rain water run-off seeping through pyritic shale becomes acidic to the extent where its pH value can be as low as 1.5.

Jan 1, 1992

The authors are looking at the behaviour of the mineral processing circuits by means of the simulators operating under random disturbance. The present paper deals with the fuzzy control systems in comparison with PID controllers. A series of tests are conducted on simplified prototype processes with (1) dead time plus first-order lag model and (2) diffusive model. In the next series of tests the self-sustained process model was introduced to improve control against dead time. In both cases fuzzy and PID controllers are optimised by EVOP method. Particular attention is paid to the effect of observation noise to analyse for the problems which can be fatal to practical applications in mineral processing. Finally the methods developed are applied to a closed-circuit wet grinding system simulator operating under random disturbance.

Jan 1, 1993

The Amacan Copper Project was constructed in the Philippines by a Finnish-Filipino Consortium during the years 1979 - 1982. The project involved a turnkey contract for a mine and a concentrator to process 25 000 tonne per day of porphy- ritic copper ore at a grade of 0.45% Cu. The orebody is located on Mindanao, the southernmost island of the Philippines, in rugged, mountainous terrain approximately 1 000 m above sea level. The adopted design principle was based on an efficient, straightforward installation utilising a minimum number of items of equipment each with high unit capacities. The consortium faced many problems which resulted in lengthy delays in construction and finally led to the client taking over responsibility for the completion of the project. The concentrator was successfully commissioned in July 1982.

Jan 1, 1986

Gallery Stoping, an old but little used stoping method, has been reintroduced to workings at the Paringa South Shaft.Orebodies which are amenable to such a method are being mined in this manner with considerable advantages and savings.The advantages of gallery stoping as used at Paringa, compared with traditional mining methods are:1. constant cash flow2. low set up cost and initial stope development3. nearly 1005 recovery 4. no access problems 5. quicker tonnagesAs compared with highly mechanized mining methods, it has been found to be slower but requires less development, gives improved grade control, has less impact on the surrounding rock and fragmentation is much better, reducing secondary blasting costs.This paper examines the mining method and illustrates the advantages of gallery stoping at Paringa.

Jan 1, 1985

By Mercer J. K

Shaft guide reaetions in No. 2 Ore Shaft, Mount Isa Mines Limited, have been reduced to a low order of magnitude by the use of self aligning slippers and spring loaded guide rollers. Before commissioning the new 4500 h.p. winder at No. 2 Ore Shaft in January, 1958, it was realised that the increase in hoisting speed from 1800 to 2650 ft/min. would cause high shaft guide reactions which would be increased further when the elongated 12 ton skips replaced the existing 7 ton skips.The Cambridge accelerometer was used to measure the shaft guide reactions and to confirm that progressive skip modifications were resulting in reduced reactions. The skip modifications were completed in 4 weeks.INTRODUCTIONIn 1956 an expansion programme was initiated to increase production from 5000 to 11000 tons per mining day. At No. 2 Ore Shaft the 1500 h.p. winder operated at 1800 ft./min. and hoisted a 7 ton capacity skip. The new 4500 h.p. winder operates at 2650 ft./min. and hoists a 12 ton capacity skip. No. 2 Ore shaft is equipped with two 5 ft. by 5 ft. hoisting compartments (Fig. 1) and any increase in skip capacity meant an abnormally long skip. This feature, coupled with the increase in hoisting speed, could have caused very high shaft guide reactions. Before commissioning the 4500 h.p. winder, a Cambridge accelerometer was borrowed from the University of Adelaide and was used to measure the shaft guide reactions. Rather than carry out an extensive shaft timbering programme, the skips were modified by fitting cushioned guide shoes and spring loaded guide rollers (Fig. 1). Testing commenced in February, 1958, and was completed in March, 1958.

Jan 1, 1961

By K Buda, W Staunton, M Hill, V Tjandrawan

One of the challenges facing the gold industry in the 21st century is the continuing need to identify new reserves of economically treatable ores. Discoveries of large, metallurgically simple orebodies are becoming increasingly rarer, forcing companies to investigate options for the processing of ores which may present recovery, economic and/or environmental issues, requiring innovative approaches to their treatment. Ores which contain naturally occurring carbonaceous material (æpreg-robbing oresÆ) are an example of one such ore type. NewmontÆs Jundee operation contains zones of carbonaceous ore within the oxidised orebody. A program consisting of detailed laboratory work and extensive plant trials has been undertaken to assess the options of the processing of this material. Laboratory tests demonstrated the advantage of carbon-in-leach (CIL) over direct cyanide leaching and carbon-in-pulp (CIP) for treatment of these ores. The laboratory program identified several factors which would enhance overall gold recoveries where preg-robbing ore was being processed, including: keeping preg-robbing ore separate from non-graphitic ore; maximising gravity recovery; and ensuring the plant operates in æpureÆ CIL mode, ie no leaching prior to first adsorption tank. Several plant trials were undertaken to assess the economic sustainability of treating moderate preg-robbing ores through a modified gravity/leach/adsorption circuit. Results indicated that where good operational control of the circuit was maintained to ensure high gravity recovery, minimal leaching prior to carbon contact, and maintenance of good, active carbon inventory, then acceptable and sustainable overall gold recoveries could be obtained. Using these relatively simple plant modifications potentially allows a plant to treat ores with preg-robbing index (PRI) values up to one. When PRI values rise to 1.3 - 1.6, leach recoveries can drop from >85 per cent to

Jan 1, 2007

By J Player

Big Bell Mine started experiencing relatively large mining related seismic events, and accompanying rockbursts, from February 1999. Twelve rockbursts damaged access development from February 1999 to June 2000, with severe damage extending for up to 100 m along footwall drives. Five seismic events associated with the rockbursts were recorded by the AGSO, measuring 1.9, 2.2, 1.7, 2.4 and 2.2 on the Richter scale. These events affected 485 and 460 footwall drives in August and November 1999 and 535 footwall drive in June 2000 (drive level nomenclature is equivalent to the depth below surface and RL). After the third event (July 1999) it was apparent that the seismicity was not a once-off phenomenon. This (sudden) onset of seismicity required management to implement a series of precautionary measures:to ensure the safety of the workforce, to maintain continuity of production, and to reduce rockburst damage rehabilitation. The measures included extended re-entry periods and exclusion zones in high-risk areas, improved rockburst resistant support systems in areas prone to damaging seismic activity and improved support systems in areas prone to shakedown damage. A full-scale minewide ISS seismic system was ordered in October 1999 and commissioned in February 2000. A portable eight-channel CSIR-Miningtek system was installed at short notice as an interim measure in August 1999. This CSIR system covered the northern producing stopes, where the majority of the rockbursts had occurred. The objective of the seismic monitoring was to monitor relative activity and to determine trends with regards to time and location. MAP3D numerical modelling was used to investigate the relationship between seismicity and various combinations of stress components to assess the relative seismic risk in both current and proposed working areas. This information is used to determine where and at what stage in the mining cycle the rockburst resistant support is required. Analysis of the seismicity has determined two distinct modes of seismicity û small-scale localised, high frequency events in high stress areas and larger events related to shear along previously intact foliation surfaces. This paper includes a summary of the seismic history, seismic data analysis, support system design, mine design adjustments and management action to minimise the effects of seismic activity at Big Bell Mine.

Jan 1, 2000

Segregation studies in ternary systems of glass ballotini, iron ore and coke particles (with size range of 1-8 mm in each) in filling and emptying a laboratory size Paul Wurth hopper are described. In-bin segregation is shown to be a function of the position in the hopper, the nature of the material and the feed composition. The in-bin results are correlated by the equation C = C0k, where C and C0 are the size compositions (wt per cent) in the hopper and feed respectively, and k is an experimentally obtained segregation constant. The results of now pallern measurements show that material discharges from the hopper according to the sequence; core now - wall now - scaffold now, where the latter represents stagnant material at the hopper wall that discharges last. Size segregation in the discharge stream from the hopper is shown to be a function of in-bin segregation and hopper now pallern. A method of predicting discharge segregation from these two sets of data is suggested. The results of the model studies are also compared with industrial data and these show satisfactory agreement. Discussion of the hitherto ignored effect of size segregation on hopper now rates, stoppages and other operating problems is also included.

Jan 1, 1985

THE object of this paper is to offer some suggestions to assist metallurgists to supervise the operations of flotation plants. We do not yet thoroughly understand what "flotation" is or "why minerals float" and all attempts that have been made to explain the phenomena have been based on theory or imagination, and have not been capable of substantiation by practical demonstration, or even by laboratory tests; but it is wellknown that particular minerals will float in a liquid under certain specified conditions, and that some other minerals will not float under those conditions, and that, if a mixture of the two classes of minerals be subjected to those conditions, there will be separation of the minerals, of which one class will float and the other will remain unfloated as a residue. The duty of the flotation expert is to so control the operations and the conditions of the liquor as to obtain the best commercial result from the ore he is treating. The chief controlling factors in a flotation plant appear to fall under the following eight headings, all of which are important:1. Crushing.2. Rate and regularity of feed.3. Density of pulp.4. Temperature.5. Addition agents.6. Condition of circuit liquor.7. Agitation.8. Aeration.

Jan 1, 1920

By Dobos K

The Clermont Goldfield, from which about 300,000 oz of bullion have been extracted, was one of the major gold producers in Queensland. This paper is derived from a systematic study of the mineralogy, geochemistry, and stable isotope geochemistry of the deposit, based on detailed field work and logging of 57 reverse-circulation percussion drilling holes at the Black Ridge Gold Deposit (Fig 1), aimed at addressing the long debated question of gold-ore genesis at Clermont, i.e., whether it is of fossil placer or hydrothermal origin.Detailed petrologic and mineralogical studies indicate the hydrothermal alteration at Black Ridge is dominated by extensive siderite (+rhodochrosite-ankerite) veinlets and stockworks, which are concentrated along the deformed unconformity between the Anakie Metamorphics and basal conglomerates of the early Permian Blair Athol Coal Measures. Siderite alteration is also moderately developed in all other rock units represented at Black Ridge, including the Tertiary basalt. Weak to moderate phyllosilicate alteration is common throughout the deposit, including chlorite-sericite along the shear zone of the unconformity, and sericite-clay in the conglomerates. A sulphide-oxides zonation also has occurred, including pyrite below the unconformity, (pyrite)-chalcopyrite-marcasite-(hematite) along the deformed unconformity, and marcasite (hematite, pyrite) in the conglomerates.

Jan 1, 1990

By J Leppinen, B Johanson, R Kalapudas, G McMahon

The Suurikuusikko gold deposit was discovered in 1987 in western Finnish Lapland, 54 km NNE from the town centre of KittilS in the volcanic belt of Central Lapland. It is hosted by tholeiitic basalts in a graphite-bearing albitite breccia. The ore is located in subvertical shear zones characterised by strong albitisation, carbonatisation and sulfidisation. The ore minerals consist of arsenopyrite, pyrite, chalcopyrite, sphalerite, tetrahedrite, bournonite and rutile. Small amounts of pyrrhotite, gersdorffite, jamesonite, bornite, gudmundite, tetrahedrite, stibnite, kermesite, berthierite and native Sb are also present. Gold occurs as invisible and as 1 - 2 ¦m size inclusions in arsenopyrite and pyrite, on their grain boundaries and in fractures. The average amount of gold leached by cyanide is 2.93 per cent. The æinvisibleÆ gold contents were studied in pyrite and arsenopyrite by electron microprobe analysis (EPMA) and secondary ion mass spectrometry (SIMS) at CANMET/ MTL. Gold element distribution images show zoned patterns both in pyrite and arsenopyrite. SIMS analyses range from 343 to 55 ppm Au in arsenopyrite and from 217 ppm down to 0.32 ppm (detection limit 478 ppb) Au in pyrite. EPMA results range from 939 to below the detection limit 24 ppm Au in arsenopyrite and from 267 ppm to below 22 ppm Au in pyrite. Recovery of the refractory gold ore was studied using grinding, flotation, bio-oxidation and cyanidation tests. A sulfide bulk concentrate containing 40 ppm Au was obtained by flotation at 90 per cent recovery (As content 5.5 per cent, S content 22 per cent, and mass recovery 15 per cent). The grinding fineness in flotation was P80 -100 to 120 ¦m. At the original fineness the cyanidation recovery from the concentrate was lower than ten per cent, after ultra-fine grinding P80 -10 to 2 ¦m the Au recovery was less than 17 per cent. After bio- oxidation, Au recovery of 95 per cent was obtained in carbon-in-leach (CIL). The bio-oxidation time was two weeks in laboratory test, but after regrinding the oxidation rate was faster and recovery of Au higher. However, the selected method for the mining to be started in summer 2008 is open pit mining and mineral processing methods sulfide flotation and pressure oxidation in an autoclave. The ore reserves were estimated 31 December 2007 as: Probable 18.2 Mt with 5.1 g/t Au, Indicated 5.4 Mt with 3.0 g/t Au and Inferred 10.8 Mt with 3.4 g/t Au. The production capacity will be 3000 t/day.

Jan 1, 2008

Sample preparation for gold samples, where the distribution and size of gold particles is often irregular, usually demands that a relatively large sample weight is taken to produce a representative sample for analysis. Traditional sample preparation of gold samples incorporated multiple stages of coarse particle size reduction followed by subdivision of the sample prior to final fine pulverising. This technique developed because of the limited equipment options available to laboratories. As a result significant errors are introduced and the final sample size being pulverised is a small fraction of the original sample weight. Three significant developments have occurred in the last 25 years to significantly improve sample preparation of gold samples: 1.  large capacity fine pulverising,2.  fine jaw crushing, and3.  whole sample coarse pulverising. In the mid-1980s an Australian manufacturer developed large capacity pulverising bowls which had the ability to reduce samples with a mass of 1.5 - 3.5 kg to a nominal 0.075 mm product in approximately three to five minutes. Laboratories were able to produce a large homogeneous pulverised sample which significantly reduced the error in sampling. However, exploration and mine samples are usually 7 to 10 kg and the sample requires a subdivision stage following crushing to produce the 3.5 kg for the pulverising step, thus introducing potential for significant error. The development of fine jaw crushing allowed particle size reduction to -2 mm which reduced the subdivision error of the bulk sample prior to fine pulverising. Subdivision of the crushed sample at -2 mm still results in potential sampling errors, where the gold particles are not sufficiently liberated to be representatively sampled. Clearly the best option would be to reduce the particle size small enough to ensure a representative sample prior to final pulverising. Continuous mills offer a partial solution but are relatively slow and subject the sample to differential pulverising prior to subdivision. Clearly this does not provide the best solution for routine laboratory applications where high volumes of samples are to be processed. The recent development of a large capacity coarse pulverising system allows samples of up to 10 kg to be reduced to -0.25 mm prior to subdivision, and fine pulverised to -0.075 mm. Laboratories now have the necessary equipment to perform reliable large capacity sample preparation of gold samples. The exact choice of a sample preparation scheme may still depend on particular ore types but the need for multiple crushing and subdivision stages is redundant.

Jan 1, 2008

THIS instrument, depends on the principle that, over a short period, the surfaee of a porous substance from which a liquid is evaporating receives the same amount of heat by conduction, convection, and radiation as it loses in the latent heat of the evaporating liquid. If, then, the amount of heat being received by a surface can be measured, the rate of evaporation can also be obtained. The Kata thermometer is also based on this principle differently applied.The instrument, as shown in Fig. 1, consists essentially of a thermometer with a sliding which is divided by three pointers into two equal parts which may be spaced so as to cover a distance of, for example, 5° of the thermometer scale. The instrument is calibrated so that the amount of heat required per unit area of the bulb to raise the menissus is known. The method of using the instrument is as follows:The slide is first set so that thc central pointer is at the temperature of the evaporating surface.The thermometer is cooled by any convenient means so that the meniscus is several below the lowest pointer. The thermometer is then placed near the evaporating surface, when the Ineniscus begins to rise and the time taken for it to rise from the lowest to the top pointer is measured. From this and the calibration results the amount of heat retained per unit area of the bulb at the mean temperature...

Jan 1, 1928

Natural gas was introduced to the Melbourne reticulation system in April 1969 and since that date sales to industrial consumers in the Gas & Fuel Corporation of Victoria area of supply, have increased by over 50% This increase has occurred despite the fact that the areas in which the new fuel is available have been dependent on the progress of the conversion operation from manufactured gas. The half way mark for conversion was reached in May 1970. The reason for the adoption of natural gas by industrial users is usually the result of objective financial analysis leading to the conclusion that the new fuel will give the lowest overall production cost. Many factors are involved in such an analysis of which the price of the fuel is only one. Amongst other important elements in the cost calculation are:- -ò òò -(1) The effect of fuel on product quality (2) Maintenance and handling costs for alternative fuel. In addition to economic gains for the individual user, the use of natural gas should benefit the whole community through its effect on such things as, air pollution and overseas balance of payments.

Jan 1, 1970

By Firkin GR, Allen RJ

Sulphide Corporation Pty. Limited has roasted a number of different zinc sulphide concentrates on its sinter machine which pro- duces zinc-lead sinter for an Imperial Smelting Furnace, and results have varied widely. The differences are considered to be functions of !concentrate particle size and reactivity. Amdel have used differential thermal analysis to examine these concentrates and two major effects have been found. Firstly, in concentrates 1containing small quantities of pyrite and chal- L [copyrite, heat is liberated at 400¦C to 650¦C [by oxidation of these two sulphides. Secondly, as particle size decreases, heat release from the oxidation of zinc sulphide commences at flower temperatures and rate of heat release In a sinter bed, the presence of some rite and chalcopyrite would help to heat the cc sulphide to ignition temperature in a orter time, while a finer concentrate would sult in roasting being completed more ickly. Both of these effects result in a arper flame front and minimise the chance heat and combustion fronts being mismatched. is theory is supported by sintering results tained by Sulphide Corporation. As a result

Jan 1, 1975

Average annual growth in consumption of primary energy in Australia over the past 10 years has been 5·5 per cent compared to a world average of 4·1 per cent.Over the next 10 years growth rate is expected to increase to 6 per cent per annum due largely to the rapid development in the mineral processing industry.By the end of the 19705 natural gas is expected to supply more than 9 per cent of Australia's primary energy market. Coal will supply 40 per cent and petroleum products 47 per cent. Nuclear energy will make its appearance but will make only a small contribution in the period.Australia has adequate reserves of natural gas and coal to supply its needs in the 1970s and beyond. However the newly developed reserves of crude oil, while supplying 60-70 per cent of requirements in the initialyears, will need regular and sizable additions if they are to keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated that new discoveries will need to approximate ten times the volume of recoverable reserves found in Australia to date.

Jan 1, 1971

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

By Borsaru M

The production of high-grade calcined bauxite is very dependent on the moisture content of the final product. Existing procedures rely on the ignition of small samples to monitor the effectiveness of the calcination process. The results obtained by this gravimetric technique are several hours behind production and do not permit regular adjustment of the furnace to optimize the control of the chemically bound water content (LOI).To provide rapid and hence more relevant results, a neutron moderation technique has been developed for measuring the LOI of bulk samples of calcined bauxite while they are still hot. The method uses fast neutrons from an 241 Am-Be neutron source to irradiate the samples, and the backscattered thermal neutrons detected are a measure of bound moisture content.The rms deviation between neutron and conventional determinations of LOI, in 15 calcined bauxite samples, was 0.08 per cent LOI over the range 0.1 to 0.9 per cent LOI. When allowance is made for the rms error in the ignition method, the error in the neutron method is found to be 0.07 per cent LOI.

Jan 1, 1985

By J E. Everett

Ore selection is generally a highly subjective task, with emphasis on producing product with a consistent target grade matching a perceived market requirement. A composite selection criterion ‘Comp’ (a linear function of the grade vector) can be used to maximise ore tonnage at a specified target grade (in Fe and contaminants) extractable from a block model. The blocks correspond to the selective mining units, with grades interpolated from diamond drill hole data. An iterative procedure has been developed to identify the coefficients and cut-off value for the composite function ‘Comp’, maximising potential ore tonnage at target grade.Commonly, target grade is predetermined by marketing; however, there is no guarantee that maximising ore tonnage at a specified target grade maximises the potential value of the mine. If the value of ore could be expressed as a linear function of the grade components, then these coefficients would be appropriate for the selection criterion ‘Comp’. The cut-off value for ‘Comp’ would correspond to the marginal cost of production; all blocks with a ‘Comp’ score above the cut-off would be classified as ore; and the cumulative grade of these ore blocks would be the average product grade over the life of the mine.Unfortunately, no such value function for iron ore is generally available. Methods for estimating the value function are discussed, using the spot price and sensitivities based either upon operational tolerances for Fe and the contaminants or upon published price differentials. This approach has been applied to an anonymous Pilbara deposit with about one million blocks averaging 1.1 kt. It is shown how the optimal target grade, cut-off grade and maximum tonnage can all be explored as a function of marginal cost and iron ore price. Alternatively, given marginal cost and an iron ore price, the effects of changing the tolerances (and therefore the relative costs of the contaminants) can also be explored.It is suggested this procedure can enable informed decision-making for an iron ore mine. Rather than setting final policy for the entire life-of-mine, the method enables target grades and tonnage estimates to be revised by re-computation as the mine life proceeds to recognise changes in market conditions and knowledge about the resource.It should be emphasised that this paper is concerned with ore selection rather than ore sequencing. Appropriate ore selection is a necessary but not sufficient condition for maximising value. Having identified the set of blocks that potentially maximise value, the sequence in which they are mined will present a trade-off between producing at constant grade and extracting high value ore early. The sequencing issue is not considered here. It is shown that optimum ore selection for an open pit mine is independent of any consideration of discount rates, although ore sequencing will depend upon the time value of money if the product grade is to vary across time.CITATION:Everett, J E, 2015. Ore selection to maximise value, in Proceedings Iron Ore 2015, pp 443–448 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By T P. Tafirenyika, K C. Corin, C T. O’Connor

There is a growing demand for copper driven by its applications in renewable energy and electric vehicles. Sulfide ores are an important source of copper. Flotation is a critical front-end process used to remove gangue minerals and concentrate the copper minerals. The electrochemical activity of sulfide minerals contributes to their overall activity in the flotation pulp. The mineral rest potential dictates how collectors interact with the mineral surface, and hence ultimately on the flotation response. Dissolved oxygen, (DO), pH, redox potential (Eh) and water composition and ionic strength are also significant in controlling flotation performance. The aim of this investigation was to determine the influence of the electrochemical environment both during milling and flotation on the flotation behaviour of bornite and chalcocite. For this investigation, the interactions of collector with bornite and chalcocite were studied using synthetic plant water (SPW1) and deionised water (DIW) at 5 different pH levels. Sodium isobutyl xanthate (SIBX) was used both in microflotation, collector adsorption and zeta potential tests.

Aug 24, 2022