Search Documents

Computer simulation of the control systems for the heavy media coal washing process have been presented in this paper. The simulation model applies the Simulink module of the Matlab 5.1 software package and allows monitoring of variations of a

Jan 1, 1998

Mispah form (FAO: Lithosol) soil contaminated with >380 000 mg kg-1 creosote was co-composted with sewage sludge and poultry manure for a period of 19 months. The soil was mixed in a ratio of 1:1 (v/v) with wood chips to improve aeration. The soil-wood chips mixture was then mixed in a ratio of four soil-wood chips mixture: one compost material (sewage sludge or poultry manure). Compost heaps were set up in triplicate on wood palettes overlaid with double layers of nylon straw bags. Control experiments, which contained the contaminated soil-wood chips mixture without sewage sludge or poultry manure were set up in triplicate. Moisture, temperature, pH, ash content, C:N ratio of the compost and the creosote concentration of the soil was monitored monthly. The concentration of selected creosote components in the soil was also determined at the end of the incubation period. Temperature was observed to rise to about 60¦C in the poultry manure and about 58¦C in the sewage sludge within two months of incubation, while temperature in the control fluctuated between 15¦C and 35¦C throughout the incubation period. Creosote concentration in the control was reduced by 17 per cent at the end of the incubation period while concentration of creosote in the sewage sludge and poultry manure compost was reduced by about 99 per cent. The percentage rate of creosote reduction in the poultry manure compost was initially lower than observed in the sewage sludge compost. However, the reduction rate became similar towards the end of the treatment period. The concentrations of selected creosote components were reduced by about 100 per cent within the same period. Respiration of compost microorganisms and counts of microbial populations showed that microbial activity correlated with reduction in creosote concentration.

Jan 1, 2004

By Brenchley R

Partitioning behaviour studies for -particles in the 250 to 1,000 micron size range at. the Curragh coal preparation plant are presented. Plant surveys were conducted to compare the partitioning efficiencies of dense medium cyclones and froth flotation. The aim was to assess the potential for improving yield of coal by directing more of the top size of flotation feed material to dense medium cyclones. ovel mass balancing and model fitting NI procedures were used. While flotation offers high yield of low ash particles smaller than 500 microns, dense medium cyclone rejection .of high ash particles larger than 250 microns is superior. These strengths of the two processes are turned to good advantage by the use or desliming sieve bends which tend to perform some density separation on the'size fractions of interest, directing lower ash material to froth flotation than to the dense medium cyclones.

Jan 1, 1987

By D G. Miljak, J Khachan, B K. Schwitter

The performance of prototype magnetic resonance sensors suited to mineral measurement in conveyor, slurry or portable applications is described. The sensors can be positioned around conveyors and modified slurry pipes, providing deep penetration of the sensing field, relative insensitivity to ore surface conditions and high mineral discrimination. Measurements on slurry, concentrates and ores sourced from mine operations are presented for two applications. Firstly, the quantitative measurement of chalcopyrite in slurry was demonstrated in laboratory measurements. In a calibration test, a standard error of 0.1 wt per cent and detection limit of 0.3 wt per cent was obtained. Secondly, results were obtained for the discrimination of iron ore texture. Signals were readily observed using measurement integration times of seconds to several minutes, depending on ore material. The results demonstrate the feasibility of online quantitative analysis of selected minerals in processing applications using magnetic resonance.

Jan 1, 2008

By D M. Weedon

This paper introduces a novel roll crusher design, which incorporates non-cylindrical crushing rolls. The use of non-cylindrical rolls enables the crusher to achieve a greater reduction ratio than is possible with conventional roll crushers. Referred to as the NCRC (non-cylindrical roll crusher), the new crusher incorporates two rolls comprised of an alternating arrangement of plane and convex or concave surfaces. The two rolls are complementary and arranged so that when they rotate the convex and concave surfaces of each roll are substantially opposed. With the rolls rotating in opposite directions at the same speed, this arrangement produces a gap between the rolls that remains approximately constant. Discontinuities on the roll surfaces provide improved angles of nip, which increase the probability of larger particles being drawn into the crusher. Initial tests on a scale prototype of the NCRC have indicated that reduction ratios exceeding 10:1 are achievable.

Jan 1, 2000

By Thomas E. G

In the economic evaluation of any Australian mining project, changes in taxation can significantly affect viability. Australian tax laws, particularly in the period since early 1973, have undergone many changes which have led to shifts in the profitability of mining companies. This paper examines the sensitivity of a selected, broadly based sample of Australian mining companies to the changes that have occurred, or are reasonably likely to occur, in taxation legislation. In the past, tax systems have been altered for a variety of reasons, such as 1. reduction'in the impact of inflation 2. neutralization of incidence between different sections of the economy 3. as an incentive to encourage expansion and growth in a particular industry or area, and 4. increase in the real "take" of government. In this paper, conventional rate of return analyses are applied in a study of how profitability is affected under various taxation systems.

Jan 1, 1977

By Rivers CJ

The Brolga deposit is a Ni-Co enriched laterite, formed over intensly serpentinised peridotites of the Marlborough Block. Basement lithologies at Brolga consist predominantly of serpentinised dunite, with lesser massive serpentinite shear, gabbro and harzburgite. Investigation of the deposit has defined 17 different varieties of saprolite, ferralite (limonite), and ferricrete. Different combinations of these varieties form three distinct lateritic associations, the Hard, Soft and Dyke Associations. Recognition of key textural and mineralogical features in each association, an understanding of basement geology, and an awareness of current climatic conditions, suggest that: 1. both the Hard and Soft Associations have formed under relatively dry climatic conditions; 2. the Soft Association reflects much poorer groundwater drainage than the Hard Association; and 3. the Dyke Association has formed from a gabbroic basement, and has also been affected by restricted groundwater drainage, caused by poorly permeable marginal serpentinite shears.

Jan 1, 1996

Ventilation characteristics of a three h -nc longwall development panel in a 1/100th tale hydraulic model using dispersion mechanics are the first applications of its Find in ventilation. Dispersion mechanics gives additional and important ventilation parameters such as degree of mixing, bypassing, -ecirculation etc. These are not obtainable the traditional pressure-volume methods. Experimentally, the model work investigates entilation characteristics of different stopping layouts, including leaky stopping,, cut-throughs and return roadway, brattice tyre ventilation and the effects of flow rate reduction on air distribution in the headings. Additionally, a model of methane generation at the face provides results used to calculate the dispersion characteristics in the return airways. It is concluded that the model resui,s -trongly suggest that dispersion mechanics could be applied to mine ventilation surveys to provide quantitative flow pattern data and details of effective dispersion '?_C!,r riro ò `b' eritilat.ing air.

Jan 1, 1983

By Pollard D. M

The BHAS copper-lead matte leach process, developed in Port Pirie, South Australia, has been in operation on a commercial scale since 1984. This process is one of many developed in the past decade to recover copper via the hydrometallurgical route. In essence, the process involves a single stage agitative leach of 100% -75um matte in an acid chloride-sulphate lixiviant with gaseous oxygen as oxidant. The leach temperature is controlled at 85¦C to assist with reaction kinetics. After leaching, divalent copper is recovered from solution via a conventional solvent extraction/electrowinning circuit to yield cathode copper for sale The BHAS matte leach process has several unique characteristics cf. other commercial oxidative acid leach processes. These include i) the use of gaseous 02 as oxidant ii) H2SO4 addition as make up acid iii) Relatively low chloride ion addition (30 g/1) For this reason, extensive work was carried out into the optimization of leaching by Meadows (1985). Variables investigated included ò Oxygen flow-rate ò Agitation intensity ò Leach temperature ò Free acidity ò Chloride ion concentration ò Matte particle size The current work was conducted to determine the effect of cooling rate, and hence mineralogy, on the leaching characteristics.

Jan 1, 1989

By Sneddon NW

Aberdare North Colliery is situated on the eastern boundary of the City of Cessnock in the Hunter Valley, New South Wales. Although the area is now noted for its wines and vineyards, the district has a long history based on coal mining. The richest coal seam in the Cessnock district is the Greta Seam, a low ash, high volatile steaming or gas making coal. The seam, up to 10 metres thick, extends over a large area surrounding the city of Cessnock and neighbouring townships such as Bellbird, Aber- dare, Kearsley, Neath, Ellalong, Kurri Kurri and Stanford Merthyr. The Aberdare Colliery, leases, which extend under Aberdare and Cessnock townships, were first worked in 1905 and continued developing pillar panels until the mine closed on 11 Nov- ember, 1960. Coal mining to this time consisted mainly of developing pillars to the 2.4 metre parting and, in some areas, dropping the top coal to the 6 metre parting, thus leaving the pillars intact, the top 1.8 metr-es of coal be- ing left untouched due to the high sulphur content. Aberdare North Colliery was opened in 1956 in order to recover and extract the pillar coal and tops left standing for over 40 years. During the pillar extraction phase the occurr

Jan 1, 1981

By Li YQ, Yoon RH

The photoresponse of natural mineral pyrite and galena electrodes has been studied in aqueous solutions on freshly fractured surfaces (some fractured in situ) using moderate overvoltages. When fractured in situ, the electrode potential of both minerals instantly drops several tenths of a volt. Pyrite exhibits a spontaneous anodic photocurrent at fracture, which indicates upward band bending (depletion layer) on the n-type electrodes. The negative surface charge responsible for the depletion layer is believed to arise from a surface state that is intrinsic to pyrite surfaces, possibly modified by hydroxide ion adsorption. The flat band potential, Vty, of pyrite is at approximately -1.0 V (SCE) at pH 9.2 but to reach V(b, pyrite has to be cathodically decomposed. In contrast, galena assumes the flat band potential at fracture. Subsequent polarisation of galena at potentials positive of Vth produces an anodic photocurrent (upward band bending) and polarisation negative of Vro a cathodic photocurrent. Most of the galena electrodes studied were degenerate n-type and at potentials negative of Vtb, no cathodic photocurrents are observed, indicating the bands cannot be bent downward, consistent with the Fermi level at the surface merging with the conduction band edge near Vn,. Several were close to intrinsic, with the photocurrent changing sign near Vn,.

Jan 1, 1993

By M Darby, B Burdett, F Lovell

The results of the process control improvement project aimed at improving the quality of Australian Bulk MineralsÆ (ABM) iron ore pellets produced by four vertical shaft furnaces are very positive. These results are achieved through process stabilisation and optimisation, improvement in process monitoring and taking early corrective actions when operating variables were outside the target ranges. A number of benefits are obtained from this project. These benefits include: More consistent and improved pellet quality. The average cold compression strength (CCS) value of pellets produced during the eight-month trial is 260 kg/pellet, which is 16 kg/pellet higher than that produced during the 12 months prior to the trial (244 kg/pellet). Reduction in the heat input by eight per cent, from 727 MJ/tonne to 668 MJ/tonne. Reduction in bentonite rate by six per cent, from 7.1 kg/tonne to 6.7 kg/tonne. Increase in the furnace throughput rate by four per cent and additional production of 10 000 tonnes per annum through process stabilisation. Better understanding of the process behaviour. This knowledge is valuable not only for setting the target operating conditions but also for developing the ABM expert system to control the process.

Jan 1, 2005

Flue gases from electrical power station boilers, roasting, metallurgical and chemical plants could be treated by flotation using conventional flotation machines. The flue gases are introduced into the pulp instead of the air. The flotation media is a suspension of Ca(OH)2 or CaCO3 or a solution of NH4OH etc containing Na oleate as collector and frother. The SO2 and dust content of the initial flue gases were experimentally reduced by 100 to 1000 times in one flotation operation. The velocity of the flue gases through flotation machines could reach approximatively 0.4 to 0.5 m/s and more against 1.5 m/s reached in scrubber absorbers used for this purpose, but the quality of purification is expected to be better for flotation, which is essential for the cases of heavy polluted metallurgical and chemical flue gases. For some chemical plants the flue gases flotation media may be different and more suitable as compared to the above mentioned media. The proposed flotation method could be used for separation of dry grinded ores in the form of aerosols, with a realisation of flotation from a closed space (gas bubble in the pulp) onto the interface liquid-air where the particles are attached inside the bubbles.

Jan 1, 1993

Marketing of mineral products has not yet succumbed to the degree of pre- dictability and exactitude that is fam- iliar to the engineer or metallurgist in pursuing their profession. Whilst the Great Market of the world economy dic- tates circumstances for the sale of min- eral products, there are more than just buyers and sellers in the determination of the revenue received by the producer. For the engineer or metallurgist he will be required to gain an understanding of these participants and of the peculiar languages of the market place. This will be only one of his tasks in learn- ing to communicate with society, as his responsibilities increase as he climbs the ladder of success. There is un- doubtedly a need for better statistical information so that producers and sell- ers can make an appropriate and earlier response to market conditions. There is in addition, a need for more aggressive concern by raw material producers for the development and promotion of better end use of their products. Undoubtedly the marketing of mineral products will be more influenced by the direct involv- ment of government agencies than has been the case in the past. Whilst that 1. Director - Marketing & Finance, North Broken Hill Limited.

Jan 1, 1975

By Andrew R. L

The Kintyre uranium deposit was discovered in 1985 in the course of following up radio- metric anomalies generated in an earlier air- borne survey. The latter survey was conducted primarily to acquire aeromagnetic data for diamond exploration and the uranium discovery was made during a subsequent campaign of base- metal exploration. CRAE commitment to the Rudall area for a range of commodities over a period of 13 years made a significant contrib- ution to the discovery of Kintyre. Other con- tributing factors included CRAE's multicommod- ity approach to exploration, management support and continuity in the geological team. The Kintyre uranium deposit (Fig. 1) is located on the northern margin of the Rudall Metamorphic Complex, 60 kilometres south of Telfer and 260 kilometres north northeast of Newman, in the Paterson Province of northern Western Australia. It is 700 metres inside the northern boundary of the Rudall River National Park (15695 sq. km) and lies between the Great Sandy Desert and the Little Sandy Desert (Beard, 1969). Intense weathering since the Permian has produced a subdued landscape around the deposit. Resistant rock types still retain an older plateau surface but it is incised by more recent streams. Other Proterozoic and Permian rocks form low, sometimes rocky, areas largely covered by aeolian sand.

Jan 1, 1988

Australia today is one of the leading countries in the fields associated with the mineral industry, an industry which accounts for over 50% of overseas income and revenue to government. This is no accident. In order to be competitive in what was recog- nised very early in the country's history as a highly profitable busi- ness, the Australian mineral industry (mining, extractive and refining metallurgy) has traditionally been very innovation con- scious, a characteristic which has been evident from the begin- ning of the industry or very nearly so: Australia's geographic isolation and the dispersion of the mineral industry over wide distances made an exchange of ideas difficult and often impossible. One needs only to look at the inaugural address given by Sir Henry Ayers, the first president of the then Australasian Insti- tute of Mining Engineers, in Adelaide on 4th April, 1892 (1) "There is probably no other pursuit which depends more on its productive development and profitable results than in the extent and application of the scientific and mechanical knowledge possessed and exercised by its manager." and "Having in view the value of the mining industry of Austral- asians, they should be urged to apply their best skill with all the scientific and mechanical knowledge obtainable to its future development."

Jan 1, 1988

The granitoid rocks in Burma can be subdivided into three main belts viz. (1) Eastern Granitoid Belt, (2) W-Sn related, Central Granitoid Belt and (3) Porphyry Cu (Au)-related, Western Granitoid Belt. The W-Sn related, central belt Granitoids were interpreted to have generated during the continent-arc collision and the Porphyry Cu(Au)-related, western grantioid belt was emplaced in a magmatic-volcanic arc above an east-dipping subduction zone. INTRODUCTION Major tectonic domains of Burma Burma region can be subdivided into N-S trending (6) major tectonic domains from west to east (1) Arakan Coastal Strip as ensimatic Foredeep (2) Indo-Burman Ranges as Outer Arc or Fore Arc (3) Western Inner-Burman Tertiary Basin as Inter-Arc Basin (4) Central Volcanic Belt (Central Volcanic Line) as Inner Magmatic-volcanic Arc (5) Eastern Inner-Burman Tertiary Basin as Back-Arc Basin and (6) Shan-Tennasserim Massif as ensialic, Sino-Burman Ranges (Bender, 1983). The Sagaing (transform) Fault and Shan Boundary Fault form as a tectonically significant boundary between Eastern-Burman Basin (Back-Arc Basin) and continental,

Jan 1, 1987

The introduction of cement into underground backfilling at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines to improve mining efficiencies gave rise to several major problems, the magnitude of which had not been anticipated. These problems were 1. A loss of recovery in the milling circuit due to the presence of cement 2. The presence of cement-rich slime layers on the surface of the fills 3. The introduction of a safety hazard due to the slippery nature of the surface of cemented fills 4. The deposition of cemented slimes on the levels and in underground sumps and dams. The loss of revenue due to decreased metal recoveries considerably offset the gains from increased stoping efficiencies and the use of cement was substantially reduced while, (a) the Metallurgical. Department attempted to identify the chemical nature of the problem and overcome it, and (b) the Mining Department investigated methods of reducing cement contamination of the ore stream. As a part of this investigation the Mining Department added polymeric flocculants to the cemented fill pulp. Testwork was carried out in the following steps 1. The available Alfloc polymers were screened to determine which was the most effective and what was its optimum dosage rate. 2. This polymer was used in the laboratory to determine the reduction of surface slime, clarity of water, and effects on strength and percolation of fill. 3. Fills were placed underground to substan- tiate the laboratory work. /+. The polymer was then added to all cemented fills going underground to study its effect over a long term. The use of flocculants not only improved the distribution of cement in the body of the fill, but also the distribution of the fines fraction of the filling material, practically eliminated slippery surfaces and improved the clarity of the drainage water. Flocculant is now added to all cemented fills and restrictions on the use of cement are gradually being lifted.

Jan 1, 1973

By P R. G Milne

A risk-based approach to optimising pit wall slope angles was trialled in the design of a 60m deep open pit in extremely weathered and distinctly weathered materials in the Kalgoorlie area. The pit used for this approach was Stage 1 of a three-stage open pit project. The Stage 3 pit will require long term stability, as it will contain the portal for a long life underground project. Information from failures induced by steeper wall angles used in the Stage 1 pit would be valuable in predicting and preventing long-term stability issues in Stage 3. In this approach, the pit wall slopes are based not on the normal factors of safety, but on the assessment of the probability of failure and the direct and indirect costs of dealing with the failure when it occurs. In this example, the benefits and risks of adopting steeper wall angles were compared in a series of graphs. These charted the increasing probability of failure and simultaneous decreasing factors of safety with increasing pit wall slope, and the range in the possible volumes of circular failures for increasing wall angles. These were brought together in a graph showing the potential excavation savings (in BCM) and the probable cost of a failure (probability of failure times the probable volume of the failure). The resulting pit design was based on the project Mining EngineerÆs semi-quantitative assessment of where and when a higher risk of failure was acceptable and where it was not acceptable as it may have unduly affected the integrity of haul roads or production. The design incorporated wider than normal berm widths to accommodate anticipated failures and to enable modification of the wall configuration if required. Several re-designs were required during the life of the project in response to aggressively induced failures. It is considered that this risk-based approach provides a practical route to optimal pit design and operation but it requires an experienced, dedicated and efficient mining team for it to be implemented with benefit.

Jan 1, 2003

By E A. Agorhom, P N. Aabulleh

The bulk of the worldÆs production of iron ore is processed into steel. The needs of the steel industry therefore demand a high exploration and exploitation of iron ore. One trend within the industry has been a great increase in the demand of iron ore and this is reflected in an increase in world steel production from 1955 to date. In addition to the high demand for steel, is ChinaÆs high appetite to feed its steel industry. It is therefore important that the iron ore potential of Ghana is showcased for eventual exploitation by potential investors to meet this enormous demand for the commodity in the industry globally. Ghana has three main iron deposits of potential industrial and commercial importance. They are: Shieni sedimentary iron ore (reserves: 1.270 X 106 metric tonnes), Pudo titaniferous-magnetiferous iron ore and the Opon-Mansi lateritic iron ore deposits. The Opon-Mansi iron ore deposit occurs in the Western region of Ghana. The ore deposits are located on top of the range of 15 hills, which extend over a distance of 24 km from Opon-valley, south of the Western region to Dunkwa. The area has an estimated 147 Mt of iron deposit, with Fe content of 52.5 per cent. This paper looks at the iron ore potential of Ghana and how it is capable of attracting potential investors to exploit this valuable mineral for global consumption.

Jan 1, 2007