Search Documents

By M J. Schultz, R L. Rude, D M. Tomko

The US Mine Safety and Health Administration (MSHA) conducted compliance assistance diesel particulate matter (DPM) sampling throughout the underground metal and non-metal mining industry. Based on that sampling, MSHA identified mines that were having difficulty meeting the DPM limit. To provide further assistance, MSHA then visited approximately 60 of the mines that were experiencing difficulty complying with the DPM standard. As part of these visits, DPM exposures were measured and control technologies for DPM were observed and assessed. Controls consisted of ventilation, clean engines, environmental cabs, alternative fuels, diesel particulate filters (DPF) and work practices. The focus of the follow-up compliance assistance visits was to assess control effectiveness and to make recommendations to mines experiencing difficulty in meeting the DPM standard. At each mine visited, the ventilation controls were evaluated, engine emissions were determined for equipment in use, environmental cabs were examined, and operational practices were noted. Additionally, control technologies, including alternative fuels and DPF were evaluated in several mines. A comparison was made of mine and section airflow to equipment particulate indices. Based on engine emissions, horsepower and operating time, the contribution of individual engine emissions to total emissions was made. Environmental cab integrity, positive pressure and air filtration systems were checked and operational practices relating to DPM exposure were assessed. This paper summarises the preference and magnitudes of controls that were typically used or needed for successful control of DPM. Additionally, results of the assessments of alternative fuels (including bio-diesel and water emulsion fuels) and DPF are presented.

Jan 1, 2005

By T R. Stacey

South Africa has a long history of rockbursts, some 100 years. During this time much research and many developments have taken place in the country to limit the occurrence of rockbursts, and to mitigate their effects. In this paper I shall present a personal view of what I consider to be important achievements, and contributions made. Some of these are: planning of stope layouts, and the use of strike barrier pillars; recognition of energy as a key factor, the use of the energy release rate ERR as a layout planning criterion, and development of MINSIM for calculation of ERR and stope planning; sequential grid stope layouts; use of backfill for stope support; and, development yielding support elements, and dynamic testing of stope and tunnel supports. The record shows the establishment of a rock engineering research powerhouse over a 40 to 50 year period and, unfortunately, the complete breakdown of this capability in the subsequent 10 years. CITATION:Stacey, T R, 2018. A personal review of South African rockburst research, experience and lessons learnt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 5–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

By Fullagar P. K

In resource definition and mine development, major capital expenditures are committed on the basis of sparse information and even in production surprises such as bad ground are not uncommon. Drill holes constitute the principal source of information about the orebody and its environment and optimisation of drilling implies maximising the yield of useful information per dollar expended. Geophysical borehole logging provides new flexibility for optimising the drilling budget. Economic benefits can flow from geophysical logging at all stages of the mining cycle. The most commonly cited benefit is substitution of diamond delineation drilling with cheaper percussion or reverse circulation drilling in cases where geophysical logs can substitute for core. This approach can deliver an attractive direct saving in drilling costs (and time) if drill meterage is unchanged, or a potentially greater indirect benefit from better ore control if more holes are drilled within the original drilling budget. More ore contact intercepts per dollar can translate into lower dilution and enhanced ore recovery, thereby increasing revenue as well as reducing mining costs. Substitution of diamond drilling with percussion drilling is not always feasible. However, geophysical logging of diamond holes is often highly advantageous in its own right, both for geotechnical characterisation as well as ore delineation. Operational advantages of logging include data objectivity, speed of interpretation and reduced core handling and analysis costs. Geophysical logging assists mining engineers by providing a continuous measure of in situ rock strength, even over intervals with poor core recovery. The additional expense of geophysical logging in blast holes can be justified in terms of more accurate ore boundary delineation and rock strength evaluation. Precise ore boundary delineation permits refinement of charge placement, to minimise dilution and maximise recovery. Detailed knowledge of rock strength can enable optimisation of blast design. Rock strength can be evaluated in real-time via analysis of drill performance data recorded with measurement-while-drilling (MWD) technology. To successfully apply geophysical logging in mines, its technical, operational and economic viability must all be established. This entails verification of the existence of appropriate physical property contrasts, investigation of the best way to integrate the geophysical results with the mining method and an objective assessment of the value of the resulting mine performance benefit. Geophysical logging is already well established in many mining operations. The greatest impediments to its wider utilisation at mines are: lack of appreciation of geophysics by most mine geologists, engineers and managers; limited interpretational aids; and the necessity to re-enter completed drill holes. In this paper we endeavour to address these issues by informing mine geologists about potential applications of geophysics, by illustrating automated interpretation of geophysical logs and by highlighting the importance of emerging MWD and logging- while-drilling (LWD) technology.

Jan 1, 1997

By D Stephenson, N R. Steward

“TerraFlowingTM” is a dewatering process that addresses both the value proposition of Tailings as a Resource™, and the safe storage of tailings. “TerraFlowingTM” incorporates two stages of cyclone dewatering followed by centrifugation of the final dilute tailings stream. In this process three dewatered tailings streams are produced; a primary cyclone underflow, a secondary cyclone underflow and a centrifuge pulp. These three streams can be combined, or used, in various configurations to achieve different outcomes. The ability to vary the cyclone and centrifuge operations and configuration enables this process to deal with tailings feed variations in particle size distribution and mineralogy and deliver consistency, or design variations, in particle size distribution, tailings solids concentrations and recoveries. Water recovery can be up to 85% of the total water in the tailings with a stackable final tailings product achieved if the three tailings streams are combined in the maximum solids concentration configuration. The primary cyclone can be operated to deliver a particle size distribution suitable for tailings storage facility embankment construction or alternatives such as concrete structures or shotcrete for support. The secondary cyclone underflow and centrifuge pulp is suitable for beaching deposition within the tailings storage facility.

Jul 1, 2021

By J Beniscelli

Some words to honour Pedro:Pedro was among the few persons with a very high level in geology modelling, resource and reserve estimation, geometallurgy development, sampling theory applications and a deep understanding of the mining industry needs. He had brilliant ideas about new developments on economic geology. He was always looking at the long-term and proposed challenging questions a decade in advance on their solution.The fundamental aim of geometallurgy is to add economic value to the mining of mine resources by timely providing information and knowledge about the relevant metallurgical variables represented by their space models. In this manner, geometallurgy allows obtaining the optimal design of a project, mitigating processing risks, optimising and supporting production plans and identifying and assessing mining business opportunities.This paper describes the conceptual framework and geometallurgical definitions and some of Codelco’s experience during the last 15 years.

Sep 5, 2011

By S D. Dessureault

In large coal strip mines, there are many different processes at work: stripping, overburden removal using trucks/shovels, cast blasting, slot dozer pushing, more fragmentation and further truck/shovel benches. A key component to each of these steps is the use of machines. In modern operations, most machine costs are tracked within Enterprise systems that transact costs and repair work order management. Similarly, in contemporary mines most machines are tracked using technology that provides precise performance measures for each key process. Such technologies include productivity monitors on draglines, dozers and drills and fleet management systems for trucks and shovels. Linking these two sources of seemingly disparate data û costs and performance by machine û would allow for the precise calculation of unit costs by specific machine. This is similar to an activity-based costing system, except in this machine-based system, calculations are made at an even finer granular level. There are many uses for such an integrated information system in mine planning and performance management, both in real-time and through historical analysis.A real-time fleet costs (FLC) measurement process was developed as part of a larger blending-related, multi-million dollar project centred on a centralised remote control room developed at the University of ArizonaÆs Mining Information Systems and Operations Management Mine Control Center. The FLC component of the overall blending system would allow a mine controller to manage the equipment fleet by viewing its cost in real time and, when mixed with other revenue-related components, the exact profit. For example, a mine controller may show high utilisation while still maintaining a production surplus. This could occur, for example, if the equipment is driven long distances. This might appear in traditional performance metrics as æhigh production performanceÆ, but in reality may prove less profitable. This paper discusses the technical development of the FLC, its deployment and its impact on controller performance, and compares mine profitability before and after its application.

Sep 26, 2011

By C Robertson, J Campos

The South African mining industry first experienced en-masse use of electronic detonators in the Narrow Reef environment using AELÆs ElectrodetÖ pre-set delay system. In recent years, programmable systems such as AELÆs SmartdetÖ have also established their position, and within both AEL and the mines there has been important learning around the strengths and weaknesses of these systems. In general, the fixed delay systems tend to be more easily appreciated by less-skilled work teams, and are very well suited to simple layouts, especially long, narrow blasts. However, development of programmable row controllers and series delay inserts has greatly expanded the field of usefulness of these systems while retaining most of the simplicity of use. The programmable systems are immensely flexible and therefore able to function under any condition, but require a higher level of discipline and knowledge. Much has been done to address this issue and make the systems user friendly, so the systems have converged to some extent. These systems are both valuable tools for achieving control over blasting in underground and surface applications. The choice of system is very dependent on the prevailing conditions. Accurate timing with electronic enhancements continues to show an increasing range of benefits to mining operations. There is a strong parallel with non electronic initiation systems which helps to understand the appropriate use of the systems.

Jan 1, 2001

By S Sineva, E Jak, M Shevchenko, D Shishin

This study represents a part of comprehensive research aimed at integrating nickel into a thermodynamic database constantly developed at Pyrosearch. The behaviour of Ni in calcium-ferrite slags is considered. An integrated approach combining experimental and thermodynamic modelling methods has been employed to predict phase equilibria in the NiO-CaO-FeO-Fe2O3 system under oxidising conditions and in equilibrium with the metal FeNi phase. The compositions of liquid slags and coexisting solid solutions have been determined through the analysis of equilibrated and quenched samples by electron probe microanalysis technique (EPMA). The research results are presented in the form of liquidus projections on the corresponding phase diagrams, considering both oxidising and reducing conditions. The solubility of Ni in spinel, dicalcium ferrite and calcium oxide as well as solubility of Fe and Ca in Ni monoxide, have been examined under several atmospheric conditions. Additionally, the compositions of the NiO-FeO monoxide in equilibrium with metal phase have been studied. The experimental data not only support the outcomes of thermodynamic modelling but also validate the parameters of the applied thermodynamic models, thus confirming the reliability and accuracy of the integrated approach.

Aug 21, 2024

By R A. Pax

Operational grinding mills emit significant acoustic emissions which are a consequence of the dynamic environment prevailing inside them. From a technical perspective, the noise presents an opportunity to determine some details of the processes occurring inside the mills. The noise generated is not random and can be attributed to a range of events that occur inside these mills, consequently non-contact acoustic determinations of in-mill behaviour provide powerful insights into the operation of primary comminution tumbling mills. To enable a logically coherent picture to be formed of the processes inside a mill, arrays of microphones have been used. This approach allows a clearer picture of the in-mill behaviour of the charge to be accessed. In contrast to single microphone approaches, usually located near the expected charge toe position, an array of microphones allows much more useful information to be obtained from grinding mill noise.This paper will discuss and present data obtained from microphone arrays positioned at the toe and shoulder locations of a mill, and how this information can then be used for the optimisation of grinding mills in real-time.CITATION:Pax, R A, 2012. Determining mill operational efficiencies using non-contact acoustic emissions from microphone arrays, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 119-126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M Khanal, J Qin, B Shen, Y Duan, X Luo

Gaining confidence in interpreting rock and strata properties of the coalmine roof is necessary for design, maintenance, modelling and optimisation of roadways supports. One of the key causes of roadway instabilities experienced in underground coalmines is an extreme variable nature (thickness, competence, discontinuities etc) of the coalmine roof. Normally, the thickness and strength of the roof are characterised with the geotechnical and geological data gathered from exploration boreholes, which are drilled often at considerable distances apart. This limited data cannot capture localised geological variations in the coalmine roof. With this background, this paper explores feasibility of using measurement while drilling concept to perform geotechnical characterisation of the coalmine roof. The parameters, for example, penetration rate, rotary speed, torque, sound, vibration, obtained during the drilling process can provide valuable insights into geotechnical properties. The paper describes the progress of the experimental work conducted at the laboratory on synthesized concrete samples representing various rock strata using a field-scale drilling machine. The samples with and without interfaces have been tested to replicate various underground roof strata. The signals returned from the drill machine, as the drill bit passes through the layers, have been analysed and interpreted to characterise whether the drill response data can differentiate various strengths associated with the rock layers. The initial laboratory results are promising as they show distinct responses of the various sample blocks in a controlled environment. The drilling data can differentiate the synthesized rock samples and detect ‘signatures’ of the roof strength variability and delineation of lithological interfaces (transitions). The weight and torque on the bit vary and show dependency on the strength of the blocks.

Nov 29, 2022

The philosophy of computer control of grinding and flotation at ZC/NBHC is presented. The performance and reliability of the in- stalled systems are discussed.

Jan 1, 1978

By X S. Li

The modern mechanical excavation machines have enough power for cutting hard rock. The ‘bottle neck’ which limits the use of machines for hard rock excavation is ‘cutting tool’. To cut hard and abrasive rock, CSIRO has been developing Super Material Abrasive Resistant Tools (SMART*CUT). SMART*CUT technology replaces the tungsten carbide (WC) tip of conventional pick with thermally stable diamond composite (TSDC) and attaches the TSDC tip to steel tool body with CSIRO worldwide patented bonding technology. This paper introduces the key features of SMART*CUT, compares its performance with conventional WC tipped tools, discusses the challenges faced by SMART*CUT and the further developments needed for successful application of SMART*CUT to mining industries.

Nov 22, 2011

By L Yao, J Li, C Sammut, B Li

The underground mine environment is inherently complex and hazardous, which necessitates ensuring mining workers’ safety. With the fast development of AI techniques, human activity recognition has become a crucial task to enhance daily life, especially in such challenging settings. This enables automatic monitoring and detection of the mine workers’ activities and operations on a large scale, which leads to better support of workers’ safety and welfare. Existing traditional uni-modal approaches, which use data of one single modality, suffer from low data quality and noise, so they struggle to generalise effectively in such extreme conditions (Li et al, 2022). As underground mines have extreme and complicated environments, such as dust, low light, signal interference, and rugged terrain, uni-modal approaches could not resolve such obstacles and are not suitable for real-world deployment. Multi-modal human activity recognition approaches could use data from multi-modal sources, thus capturing complementary information and producing robust and effective performance in recognising and monitoring mining activities. In this case, designing suitable multi-sensor hardware and AI activity recognition models has become a pivotal task. Producing efficient multi-modal approaches for edge deployment is another problem worth exploring.

Sep 1, 2024

Mining education in Ballarat has a long and proud history dating back to the 1870s. Today the School of Engineering continues this tradition at the University of Ballarat. The recent review of Tertiary Minerals Education by the Minerals Council of Australia has questioned the current situation regarding Minerals tertiary education in Australia and recommendations have been made regarding the future of minerals tertiary education. This paper initially examines the original recommendations made by the Minerals Council of Australia and assesses subsequent changes made to these recommendations. Secondly the paper outlines the future shape of mining education in the light of these recommendations given that they are implemented. Finally the future delivery of mining education is discussed, particularly with respect to the impact of modern technologies.

Jan 1, 2004

By A Turichshev

The synthetic rock mass (SRM) approach for modelling jointed and veined rock has been at the forefront of caving geomechanics research for years. A well-constructed and calibrated SRM model can capture the full rock behaviour at a macroscopic scale. Traditionally, SRM technology employed bonded particle models (BPM) due to their ability to model rock’s response to loading without prior specification of behaviour. The SRM modelling process requires the BPM to simulate intact rock and the subsequent introduction of fractures or veins by changing bonding characteristics between the particles. However, bonded particle materials have difficulty reproducing both the compressive and tensile strengths of intact rock. This and other limitations of BPM have been the driving force in exploring the potential of grain-based (2D) and bonded block (3D) models (BBM).This paper reports on recent work exploring the applicability of both BPMs and BBMs in 3D to the modelling of intact rock. The advantages and limitations of both BPMs and BBMs are addressed based on the results of numerical simulations using the PFC3D and 3DEC distinct element codes. The preliminary results suggest that BBMs are better suited for simulating intact rock behaviour than BPMs. Ongoing work aims to better qualify the applicability of BBMs under different conditions. This has significant implications for our understanding of rock mass behaviour in a caving environment.CITATION:Turichshev, A and Hadjigeorgiou, J, 2016. Simulating intact rock behaviour using bonded particle and bonded block models, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 453–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J Q. Shi, M Karakus, Y Liu

Predicting the spatial distribution of rock mass properties in cave mining is a critical challenge. In this study, we introduce a novel machine learning-based model to advance our comprehension of rock behaviour. This model specifically focuses on the spatial distribution of rock mass and mechanical properties, a crucial aspect of our understanding of rock mechanics. Our model is inspired by the recognition that neighbouring information serves as crucial prior knowledge for predicting the spatial distribution of these properties, wherein closer neighbours are likely to exhibit similar characteristics. To effectively capture and model these neighbour relationships, we design a neural network-based model to map the spatial locations within the data set into a new highdimensional space. Within this transformed space, we utilise Euclidean distance to identify N neighbours. Leveraging these neighbours, we introduce a straightforward yet highly effective approach—label propagation—to construct a graph that illustrates neighbour relationships. This graph not only facilitates the prediction of the spatial distribution of rock mass properties but also offers a measure of uncertainty for these predictions. We validate the proposed method using a real rock data set and showcase its efficacy in capturing intricate relationships and distributions within rock properties, enabling precise predictions across diverse spatial scales. Our results underscore the potential of machine learning-based approaches to revolutionise the field of rock mechanics, providing valuable insights applicable to geotechnical engineering, mining, and other sectors where an accurate understanding of rock properties is paramount. This model has direct practical implications, offering a new tool for geotechnical engineers and mining professionals to enhance their understanding and prediction of rock properties, thereby improving safety and efficiency in their operations.

Sep 1, 2024

Brisbane based and listed on the ASX, Eastern Corp is pursuing the development of coal projects in New Zealand. There are various reasons why New Zealand coals are of interest û substantial resources, stable political/economic environment, close to Asian markets. In just over 12 months, Eastern has secured an operating coal mine (Cascade) and a prospective exploration area (Whareatea West), both on the Denniston plateau region, on the south islandÆs west coast. A key focus of activities is the development of relationships with key stakeholders and the promotion of the local economy.   Certain barriers may exist to the entrance by foreign companies into the New Zealand coal mining sector. These include geological challenges provided by the heavy faulting of the coals, port and rail infrastructure constraints, and the ægreenÆ factor.

Jan 1, 2005

By T C. Hughes, R Hughes

Ausmelt has developed and commercialised high temperature reactor technology that has been applied to waste processing in the form of a catalytic waste converter (CWC). Ausmelt Technology uses a top submerged lance system within a versatile converter containing an oxidised molten siliceous slag. Metals and other valuable products can be extracted from wastes for recycle into the community. Non-valuable components such as toxic organochlorinated compounds are destroyed and prevented from reforming. The slag produced is inert and can be safely used in building and concreting. The CWC can be applied to practically all types of wastes and examples from Ni-Cd batteries to toxic wastes are discussed. Additional benefits can be derived from large-scale operations if the surplus heat generated is exploited to produce steam and electricity.

Jan 1, 2000

By Kubik K

This paper reviews the historical data on relative height changes of landmasses with respect to sea level for Pacific Rim countries.It discusses existing theories of the Greenhouse effect, and the interaction with the vertical movements of the continental plates which leads to different effects for different places. Possible future scenarios are described and directions for future research and measurement programs are given.Relative sea levels are governed not only the increase of water from deglaciation but also by a range of other factors such as variable water storage in lakes and the atmosphere, thermal expansion of the ocean, ocean currents, and the shape of the ocean and the continents. Sea floor spreading, for example, is ultimately more significant than deglaciation in sea level control but is generally much slower.

Jan 1, 1990