Search Documents

By I Taylor, M Nugus, C Gordon

Resource estimation and selective mining of structurally complex, high nugget orebodies presents a major challenge to the Mine Geologist. At the Golden Pig BIF-hosted gold deposit in Western Australia, an estimation method has been developed that replaces an assay-based resource estimate with one based on mineralisation intensity. Subjective coding of the mineralisation intensity has a more robust connection to local grade than drillhole assays. Indicator variograms of the five mineralisation codes are well structured with anisotropy directions similar to observed structural controls. The proportion of each mineralisation code is estimated and a weighted average of the average grade of each code calculated for a block. Initial validation has shown that the model is a good predictor of the mineralisation intensity, and the application of appropriate local average grade for each mineralisation code gives a reliable block grade estimate.

Jan 1, 2003

Many problems result when coal mine shafts are built in complicated geological conditions and serious shaft lining ruptures have often occurred in the eastern part of China since 1987. Grouting is applied as one of the major measurements for shaft lining ruptures. However, as the general location of reinforcement grouting for shaft lining is deep in or near the bottom aquifer, while using cement grout as the grouting material, the grouting mostly belongs to fracturing grouting in deep alluvium. In these conditions, the mechanism and behavior of fracturing grouting has not yet been understood. From these points of view, this paper describes the mechanism of shaft lining rupture and fracturing grouting and then discusses the effect of grout injection on the stability of shaft lining by means of numerical analysis and field data obtained so far.

Dec 6, 2010

By Nagai K, Moriyama K

Toyo smelter has been making s veral efforts to reduce and diversify energy for dealing successfully with such :n:;rgy problems as the first and second oil crises. ::,specially it is one of th:; most important subjects to substitute oil by alternative: energy source, because oil is expensive and unstable with respect to its supply. t _'hercfore i was decided to propel tnC ezhstitution of coal *jr oil. in the first place, the supple- mental fuel oil in the reaction shaft was replaced by oil to coal in 1981, and then th, fuel substitution of pulverized coal was achieved in the steam superheater in 1984. 3y these fuel substitutions about 7u,' of the total fuel energy at 2oyo smelter has been replaced by coal. in this paper the fuel substitu- tions at loyo smelter are described in detail.

Jan 1, 1987

BHP Minerals Ltd operates an open cut iron ore mining operation on Koolan Island, off the coast north of Derby in the Kimberley region of Western Australia. The mine comprises a number of pits, the largest of which is situated adjacent to the coast on the southern side of the island. The lowest bench is currently at RL +2 m, and the mine has planned ultimate depth of RL -82 m. Mining has already extended below the pre-existing water table level, and below mean sea level. In 1984, an extensive program of drilling, geophysics and test pumping was instigated to evaluate the aquifer hydraulic properties and the nature of the groundwater flow regime. With the aid of computer modelling, predictions have been made of the likely dewatering and depressurization requirements, and a conceptual pumping and drainage system has been designed.

Jan 1, 1986

By L Crew, S Jackson

A trial of an Adept Online Ore Sizer (OOS) was undertaken at the WMC Leinster Nickel Operation (LNO) in the first half of 2000. During this time the On Line Ore Sizer has been shown to be a robust and accurate instrument for measuring mill feed ore size. Data collected during the trial indicates significant variation in the F80 of the SAG mill feed. The effects of feed size on milling parameters such as mill weight, mill power draw and mill efficiency appears to be dependent on the ore blend treated. With some ore blends a weak positive correlation was found between ore size and mill weight and milling efficiency but with others no correlation is evident. It is believed that the OOS will become a vital piece of equipment in the future as LNO continues to optimises its milling circuit.

Jan 1, 2000

To explain in any depth the industrial relations of Broken Hill I believe that it is necessary to trace some of the many happenings that created the present industrial climate. While appreciating that our relations with the local industry are relatively good, it must be pointed out that to preserve and improve this present situation a duty is owed to everyone connected with the industry (workers, share- holders, etc.) by management and unions to see that just and reasonable agreements are found for any disputes. If the companies ever take the local position for granted it would soon die, killed by someone who may get some short term benefit, but who would lose something of incalculable worth in the long run. Similar- ly if the unions were to adopt some of the "wild cat" methods adopted in other parts of

Jan 1, 1975

Mining companies around the world are seeking methods to coordinate operations between the mine and the concentrator to achieve an overall improvement in enterprise performance. In several instances very significant increases in productivity (more than 20 per cent) and profitability (more than $US 10M per annum) have resulted from such efforts. The key to realising these large benefits has for the most part arisen from improved communication between mining operations and plant operations personnel and the judicious use of new tools to evaluate alternatives for improvement and to minimise the risk of implementation. This paper presents a systematic approach to mine-to-mill optimisation . The importance of systemic thinking and systems optimisation methodologies is emphasised. New tools for evaluating operational performance are discussed. Recently reported benefits are summarised. Finally current research is discussed and projections for the future are given.

Jan 1, 2000

By Purvis A. H, Greenwood-Smith R, Sowerby B. D

A nuclear technique for the determination of copper and nickel in bulk samples and drill core has been developed at Lucas Heights andfield-tested at Mount Isa. The technique, which is highly specific to the element being measured, utilises the gamma-ray resonance scallering process.A bulk mineral analyser was installed in mid-1976 for the routine assay of copper in bulk samples and drill cores, and remained in operation until late 1981. The operation of the analyser over this five-year period is reviewed with particular emphasis on reliability, accuracy and principal usage.The main application of this analyser was in stope planning and design whereby several thousand drill-core and Wall-chip samples were analysed. It was also used as an aid to underground grade control of stopes where ore dilution by supporting barren backfill was a problem.

Jan 1, 1984

By Chapman G. J

Mining operations require detailed and precise methods and procedures for the optimum selection of ore from waste. A fundamental procedure applied to achieve this selection is accurate sampling. The key parameter to accurate sampling is an understanding of the degree of heterogeneity of the key element contained within a sampling mass. This paper will describe the methods applied for the calculation of the fundamental sampling error and the techniques used to achieve a representative sample in the Fimiston Open Pit, Kalgoorlie.The utilisation of Pierre Gy's sampling theory has optimised the blast hole sample quality and quantity for submission to the assay laboratory. This has resulted in reduced cost and optimised assay reliability in statistical terms. Similarly the analysis of exploration drill holes for resource definition has optimised drilling procedures in terms of the drilling method, sample length and sample quantity.

Jan 1, 1993

Process control computers are finding ever increasing applications within the chemi-cal and mineral processing industries.To purchase a system which fulfils both the immediate and future needs of operating, technical and management groups, requires an appreciation of the capabilities of the system software and the constraints which apply to user development of application software. Early decisions are then required as to who will develop and maintain the software. Rules and conventions must be determined and adhered to if the end result is to be an orderly, well structured and properly documented system. Software development and maintenance represents a substantial, and often hidden, cost. Getting it right the first time will avoid either a major re-work, or having to live with a system which is extremely diffi-cult (at the worst, impossible) to trouble-shoot or modify.

Jan 1, 1985

By Hughes A

Nchanga Division of ZCCM has installed and operated a trolley assist system on part of their truck fleet for some three years. This paper examines how the system came to be chosen and how the many features of construction and operation were dealt with. The economics and productivity of the system are presented as are the personnel aspects of acceptance and training. Zambia Consolidated Copper Mines is a state controlled copper mining company formed by the amalgamation of the former Nchanga Consolidated Copper Mines and Roan Copper Mines. The company operates seven copper mines the largest producer being the Nchanga division, which is scheduled to produce some forty-two percent of Zambia's copper production. The division operates four open pits and an underground mine which produce annually some 192 000 and 96 000 tonnes respectively of copper contained in ore.

Jan 1, 1986

The Geograph is a revolutionary seismic system involving special techniques in combining the use of FIT magnetic tape with shock wave echoes created by a weight dropping system.The idea of- weight dropping as a- source of seismic energy is not a new,.,oxie. Records 'indicate òa pos'sihle use of falling weights as early as .1929. 'Dr. Burton McCollum began his experiments in 1938, but it wasn't until 1951 that the method was first proven useful.The first weight dropping crew began commercial operations in Edwards and Sutton .Counties of West Texas in 1953. By 1962, more than '40 weight drop-ping.crews have come into existence with operations in the United States, Canada, Algeria, Iraq, Argent na,òSpanish West Africa, Tunisia, Qatar, Niger Morocco and Libya by most major oil companies and larger independent oil companies. .

Jan 1, 1962

By B J. Fallon

This study used structural equation modelling (SEM) to develop a series of models to explain the impact of work-life balance on employeesÆ perceptions of job performance, job satisfaction, turnover intentions and absenteeism. The sample comprised 257 participants (108 males and 149 females) from a range of occupations and levels of seniority. In sum, the results clearly demonstrated that successful work-life balance is associated with higher levels of job performance and worker satisfaction and with decreased levels of absenteeism and turnover intentions. The data also lent support to the impact of employeesÆ coping styles, schedule flexibility and supervisor support on employeesÆ abilities to balance work and life. It is concluded that tangible benefits to an employerÆs bottom-line can be anticipated from organisational initiatives to assist employees to better balance their work and personal lives.

Jan 1, 2005

By Morley I. W

Offshore minerals legislation has been introduced to provide jurisdiction over the exploration and recovery of mineral resources, particularly petroleum, from the territorial waters and parts of the continental shelves adjacent to coastal states. Ratificat- ion of the 1958 Geneva Conventions on the Law of the Sea has provided some measure of international agreement amongst signatory powers. Because the relationship of the Australian States to the Commonwealth in their federal system, the Australian offshore petroleum legislation is of particular interest. The customary role of the States in mineral resources management, which has extended to the offshore, is under challenge from recent unilateral Commonwealth Government legislative actions in the fields of mineral resources jurisdiction. Environmental considerations provide an additional issue, as yet unresolved, with the delay in submission of the Report of the Great Barrier Reef Petroleum Drilling Royal Commissions

Jan 1, 1974

By A B. Bell

The health and in some cases survival of mineral exploration and mining companies is, in today's markets, more dependant than ever on the effective use of information technology. The need for speedy collection, organisation, maintenance and distribution of corporate and project information is a phenomenon that will continue to strengthen with market thirst.Geographic Information Systems (GIS) provide a medium for storage, maintenance and retrieval of data, and Internet Mapping adds a technology for effective distribution of that data. Combining these technologies can return benefits both fiscally and technically by reducing costs of ownership in IT infrastructure and increasing the efficiency and effectiveness of both internal and external information delivery.GIS and Internet Mapping technologies have reached a practical stanza in their evolution and will continue to develop as a key business tool in the natural resources sector.

Jan 1, 2002

By Harris RW

Acoustic Emission structural integrity evaluation tests rely on the validity of the detected acoustic emission data and the ability of the practitioner to both analyse and interpret the data to make a correct decision on the future use of the structure tested. Unfortunately with acoustic emission surveillance testing, it is not possible to know that all the available data has been assessed property. The equipment sensitivity, threshold settings, and event capture capacity, when combined with the decision making ability of the operator in real time, make it very difficult to achieve reliable integrity evaluation. The main problem is to interpret the data and so any monitoring system should involve expert systems in conjunction with both acoustic emission and other operational monitoring data to maximise the utilisation of the large amounts of information now available from operating plants, mines and structures.

Jan 1, 1991

The last decade has seen a dramatic change in the. size and complexity of mining and mineral processing projects in Austral- asia. Major projects of today are vastly different from major projects of the 19.50's. This change has in turn resulted in a change in the role-of consultants whose contributions have been increasingly in the provision of specialist services and less in the form of overall project design and construction supervision. It is anticipated that, the specialist function will continue to represent the principle mode for consultant participation in major, projects. However, by means' of international affiliation, the development of comprehensive engineering and project management capabilities and possibly as a result of Government intervention, it is expected ,that local consultants will assume an increasing degree of participation in.the overall project design and supervision Function.

Jan 1, 1975

By Arnold J. J

The design of a coal preparation plant using bore core data cannot be discussed without some reference to the wider considerations of design. A thorough knowledge of coal preparation processes and processors as well as ancillary equipment is essential if the coal properties determined from bore cores, are to be fully utilised. Whilst generalised information of processes is available from a wide range of publications and equipment suppliers for the intending plant designer, local operational experience must be taken into account where there are similarities. However it would be wrong to assume that satisfactory plant design can be achieved merely be repeating previous design parameters. A detailed examination of bore cores used in conjunction with well proven design 'criteria will identify important differences in design parameters without which efficient and economic plant/sectional sizing cannot be achieved.

Jan 1, 1977

A continuous casting machine, of the Concast curved mould design casting billets in four strands, was commissioned at the Newcastle Works of The Broken Hill Proprietary Co. Ltd., in November, 1967. Quality assessment of early casts from this plant indicated that steel cleanliness was sometimes inferior to that of equival- ent ingot cast steel. Extensive trials to develop a modified deoxidation technique were not successful in improving clean- liness to the desired level. A "contra-flow" gas shroud, to cover the steel stream between the tundish and the mould, was developed, and proved successful in achieving the required levels of product cleanliness. The inclusion content of six grades of steel ranging in carbon content from 0.10 to 0.70 per cent is examined, and an attempt is made to explain theoretically some of the results obtained.

Jan 1, 1972

By Gregory O, Winters BI, Garlick C, Rogers H, Ye ZC

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multi- hearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80% metallization) from the rotary kiln and completes the reduction process to produce iron of nominally 3% carbon. As the melter operates at around 1500 ¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995