Search Documents

By Patridge A. C

Hydrocyclones have widespread use as classifiers in applications such as mine fill preparation and coal preparation. A fundamental conflict often exists between recovery of all of the valuable material and maintaining the quality of the product. This conflict is a result of a portion of the feed material passing through the cyclone, effectively without undergoing any classification. This paper describes an investigation, undertaken as an undergraduate project in mining engineering at the University of NSW (Brook, 1994), into aspects of cyclones in which supplementary water injection is used in an attempt to reduce the amount of misplaced fine material reporting to the coarse product and hence improve the overall classification efficiency. In particular, the study concentrated on the effects of different modes of water injection. Two methods of introducing wash water into the cyclone body were investigated. A series of tests were performed on a laboratory hydrocyclone having provision for radial water injection at different levels through small orifices in the wall of the conical section, and a preliminary study was made of the performance of a novel cyclone in which the conical section had walls of a permeable polyethylene, permitting a uniform introduction of wash water over the entire surface.

Jan 1, 1995

By Billington WG

A structural study of northwest Fergusson Island, part of the D'Entrecasteaux Group, was undertaken using colour and monochrome aerial photography and Landsat imagery. The resulting interpretation shows an upstanding, in part, dome-like metamorphic core complex, which is bound on three sides by an en echelon series of low-angle, thrust faults. Faceted gneissic layers occur throughout the complex. These facets are triangular in plan view and range in size from a few tens of metres, to massive composite zones which traverse the entire uplifted zone, The lower surface of each of the facets are, in fact, low-angle decollements which, during uplift, slid one upon the other to accommodate the vertical and extensional movements. As a consequence, deep structural valleys developed which widen towards the zone of maximum uplift. In many places, recognisable topographic features are replicated on both sides of these valleys, and under the stereoscope can be visually reconstructed to their original pre break-up positions. The southern margin of the core complex is less dome-like and falls away, via a series of deeply-entrenched structural valleys, towards a volcano-studded lowland. The lowland appears to belong to a rift or arm, stemming from the more southerly located Goodenough Bay Infrabasin.

Jan 1, 1987

By Brien RT, O&apos

The work reported in this paper extends,-bhsb on the "Heat Hardening of Artificial Magnetite ;Pellets"., which was described at the- International Symposium on Agglomeration ;-sponsored by the American Institute. of Mining, Metallurgical and Petroleum Engineers at Philadelphia; U.S.A. in April, 1961. Whereas- that work was of a.,more basic nature, -serving to illustrate the suitability of artificialòmagnetites with various.admixtures, to the application of heat hardened pellets, on: this occasion the aim-is to illustrate the procedures-which were used-to- establish the dimensions of commercialòrecuperativ strands for Australian raw materials,The nature of the pellet feed, i.e. relatively uniform :spheres of4 3/8 in. - 7/16. in. diameter, makes it possible to use small scale static pots for test work. By the use of a closed system and the measurement of suctions, gas f lows, and temperatures through beds, the speed and heat requirements of the various stages of heat hardening can be measured, so: that for a specified quality of product estimates can be made of the broad design characteristics of a moving grate system. In practice of course it is .usual to correlate the data from this type-of :experimental 'apparatus with . existing production units upon which good operating data, in the statistical sense, are available.

Jan 1, 1963

MR. L. C. BALL, chief government geologist, Queensland, wrote: This paper is intended as a severely mechanical exposition of the means adopted to deal with tremendous inflows of water concurrently with development and exploitation; but incidentally it serves as a splendid exposition of close co-operation maintained between the geological and engineering branches of this large organization.I have been impressed by the completeness of the mine plans of 'Mount Isa Mines Ltd.; but only such a paper as this has brought fully to my understanding the difficulty and complexity of the solid geometry involved in the detection and plotting of the orebodies and their stratigraphic control, including faults and large-scale brecciations, and the managerial foresight that set going the initial investigations.The company's geological branch of course must be given full credit for the results attained, but it gives me pleasure that the Geological Survey of Queensland has been closely associated in much of the study.It is noted that complete drainage was affected, but it would be interesting to learn whether the brecciated zone will again become waterlogged and whether from above or from below, and whether there has been any change in the dissolved mineral content of the water as the work progressed.

Jan 1, 1939

By Salehi M. R

Although inherent mineral matter appears to have no effect of the reflectivity of inertinite in the reflecting light microscope, it has a marked effect on the grey levels resulting from the backscattered electron response in the scanning electron microscope. Inertinite with a high inherent mineral matter content has a high grey level response but not as high as that of mineral matter. The highest grey level response is with inertodetrinite which at times could be mistaken for mineral matter. Fusinite has a higher grey level response than semi-fusinite. The backscattered electron grey level response corresponds to average atomic number and hence approximately to density. If a porous structure develops and becomes filled with mineral matter such as S, Cl, Ca, Si, and Al the grey level will be higher. Micrinite has an unusual response in that it behaves like an exinite maceral in the SEM rather than an inertinite maceral. It either has a low grey level when relatively free of inherent mineral matter, or a low grey level background with high level granules corresponding to Si and Al dominantly. Similar structures have been found in exsudatinite and resinite. It is thought that micrinite results from the migration of hydrocarbons out of exinite giving a porous structure which usually accommodates inorganic matter.

Jan 1, 1991

Trucks are the primary means of bulk material transport in Open Pit hard rock mines worldwide. They are considered to be the most- flexible system available. The large number of trucks used in some mines provides flexibility. Spare units allow for the reduced availability of the single units. Trucks have however very poor energy efficiency. Only 40% of the consumed energy is for transport of the payload, the remaining energy is required to move the dead load of the trucks. With the increase in cost, pressure, mine operators are now looking for alternative methods to make their operation more economical. Energy conservation and increasing haulage distances and uphill haulage are major factors in many well established operations. New methods have already proven themselves as more economical alternatives. Belt conveyors are an alternative means of transport with much higher energy efficiency. They use up to 80% of the consumed energy for transportation of the payload. Energy costs for conveyors are 30% of the energy costs for trucks on level transport and as little as 15% for elevating payloads. Belt conveyors require much fear spare parts and wear components than trucks. A factor of one to two times applies for level transport and ten to twenty times for uphill transport.

Jan 1, 1986

By N J. Beukes, J Gutzmer, C Reinke, M Bau

In this study the light sparse phase search (SPL_Lt) mode on the Mineral Liberation Analyser (MLA) was successfully used to identify and quantify the abundance of rare earth element (REE) phosphates in Precambrian iron formations. Monazite (light REE phosphate) and xenotime (Y and heavy REE phosphate) are identified and data from the MLA combined with the mineral chemistry of the two minerals are used to calculate and model the expected REE concentration and distribution in these two REE phosphates. The REE phosphates account for up to 31 per cent of the REEs in the banded iron formations (BIFs) and excellent correspondence is observed between the modelled REE patterns and the whole rock geochemical data available for the same samples. Except for quantifying the mineral weights, the sparse phase search also allows for the localisation of REE phosphate grains and the observation of their association with other minerals using backscatter electron (BSE) imaging. These observations are used to conclude that the REE phosphates were most likely of diagenetic origin, with REEs and phosphate remobilised from primary chemical precipitates. It is demonstrated that automated mineralogical techniques can be used to qualitatively and quantitatively describe the influence of a rockÆs trace mineralogy on its geochemistry.

Jan 1, 2008

Structure is the most important control on the location of hematite deposits in the Hamersley Province in the Pilbara region of Western Australia. Unravelling the structural history of mineralised areas, however, is complex because the Province underwent three orogenic events, and three regional extension events followed the main episodes of compression. Steeply E to ENE dipping normal faults immediately predated deposition of the Beasley Quartzite of the lower Wyloo Group after the Ophthalmian Orogeny. Steeply NE and SW-S dipping normal faults predated deposition of the McGrath formation of the middle Wyloo Group, following the Panhandle Orogeny. The resulting interpreted rift was subsequently reactivated and tilted during the Capricorn Orogeny. Late NE trending normal faults are confined to the eastern half of the Province. High-grade hematite deposits occur in rocks that range from intensely folded (Mt Whaleback, Giles Mini) to rocks with less, or only little deformation (Paraburdoo, Channar), suggesting that folding had at best limited influence on ore genesis. In contrast, extensional normal faults are always associated with high-grade hematite deposits, and in particular faults that link the underlying dolomites of the Wittenoom Formation with the overlying iron formation, thus providing a pathway for mineralising alkaline fluids.

Jan 1, 2005

By Morandini AF, Occella E, Clerici C, Mancini R

This contribution presents the first results of an experimental research aimed at finding an unified description of the first stages of a rock comminution process. With reference to the case of the jaw crushers and to the specific subject of the comminution law, the tests reviewed and analysed in this contribution have been carried out, at a laboratory scale, on five different materials (limestones, quartzite, serpentinite) at different reduction ratios and feed rates, and accurately recording both total power and idle running power. The analysis of the results has shown that: ò the grain size distribution of the products complies with a modified form of the Rosin-Rammler equation, already found to be well suited to representing the grain size distribution of blasted rock in previous works by the authors; ò observed trends of the consumed power at increasing reduction ratios is steeper than predicted by the classical Rittinger, Kick and Bond laws, Rittinger law representing however a closer approximation of the experimental results; and ò a more accurate description of the experimental results is provided by a modified form of the Rittinger law. Accuracy of the semi-empirical expression has been found to be usually better than ten per cent by comparing actual results with expected Results.

Jan 1, 1993

With the continued drop in export coal prices (as measured in US$) delivered to the Pacific Rim market, and a fixed annual 12 per cent increase in overburden, Usibelli Coal Mine Inc was faced with the need to reduce mining costs substantially or else forfeit its foreign coal contractual commitment which amounted to about half of annual mine output. Management made a difficult and fortuitous decision to proceed with an engineered plan to switch from a two seam, extended bench dragline operation to a two seam, cast blast and spoil side operation. While down-sizing and cut-backs became the rule in all departments of the mine, the drilling and blasting budget was more than doubled. Most will agree that this is contrary to what usually happens when a mine is faced with down sizing. The more common scenario would have management target the drilling and blasting budget for decrease as a first priority to cutting cost, and then later witness a decrease in equipment performance leading to an increase in the production cost per tonne. Although Usibelli Coal Mine more than doubled its annual drilling an blasting budget three years ago, the overall stripping cost has be, reduced by more then 37 per cent.

Jan 1, 1995

By Churchill M

One of the significant changes which has occurred in the flotation sector of the minerals industry, over the last two decades, has been the successful development of the very large flotation machine. The last twenty years has seen the volume of the individual cell, available to the industry, increase by a factor of ten. Today, new mills, and existing mill modernization plans, can consider individual cell volumes as large as 85 m3 with the certainty that the metallurgical performance capability of the large machine is inherently as efficient as the smaller machine. The large flotation cell offers benefits to the user such as reduced floor space, lower total power, process control simplification, and reduced maintenance. However, the flotation machine size selection process, based on overall installation economics, must include such factors as process tonnage, flotation kinetics characteristics, and metallurgical performance objectives. This paper discusses the flotation machine size and circuit arrangement selection based on both metallurgical performance and economic considerations. A computer based flotation kinetic analysis technique, which has proven valuable in quantifying the metallurgical response of flotation circuits having different cell sizes and number, is utilized to illustrate the selection of cell size and arrangement best suited to a client's Requirement.

Jan 1, 1991

By Golding D

The Charters Towers goldfield is located in the centre of a Lower to Mid-Palaeozoic igneous complex where schistose, amphibolite-grade metamorphic rocks were intruded by multiple phases of medium grained granodioritic rocks. Several generations of mafic and felsic dykes also occur. Two distinct mylonites cut all but the youngest granitoids. Gold mineralisation occurs in quartz veins located in brittley reactivated mylonite and in sympathetic fissures in the undeformed granitoids. The gold-quartz veins occur in complex, gouge-filled, 2.5m thick zones, with minor sulfides, surrounded by zoned phyllic and propylitic alteration assemblages. Four main vein systems are each restricted to separate granitoids or contain oreshoots near granitoid contacts. No genetic relationship between the granitoids and the vein systems can be documented. The early mylonitic fabrics and the granitoid contacts played an important role in ground preparation and in the localization of oreshoots. Non mylonitized granitoids also served as favourable hosts for many of the lodes. Whole rock values of 180 of the granitoids range between 6.5 and 7.9 per mil. Hydrothermal vein quartzes have 180 values between 12.2 and 15.7 per mil. Mylonite quartzes have values of 8.4 per mil. Variation in 180 values of quartzes is in part related to granitoid host rock type.

Jan 1, 1987

With more difficult economic conditions and increased competition, the Australian exploration industry is allocating increased resources to developing more effective and efficient exploration technologies. A significant number of new techniques have been developed, and Australian companies are now at the forefront of exploration technology worldwide. These should increase the chances of maintaining Australia's leading position in world mining over the long term.

Jan 1, 1987

By M Revell

The paste fill system at BHP CanningtonÆs underground silver-lead-zinc mine is described. The first of its type in Australia, the paste fill system has been operational since December 1997. Key technical and operational learnings since the first underground stope was filled are presented. Issues addressed include plant performance, pipe wear and failure, automatic control, rheology and in situ performance.

Jan 1, 2000

In recent years a large number of Horizontal Belt Filters have been installed in the Australian mining and chemical industries. This paper deals briefly with the general background and advantages leading to the selection of this type of filter. Several different applications are described and particular reference is given to the simplification of the fines treatment circuit at the South Bulli Coal Washery.

Jan 1, 1989

The different electrowinning cells presently developed for recovery of gold from CIP eluates are compared and contrasted. The efficiency of operation for each cell is,discussed in terms of the electrochemistry of (a) gold deposition, and (b) packed bed electrodes. The advantages and problems associated with each cell design are presented and recommendations are made as to the best method of gold recovery.

Jan 1, 1982

Selective leach analytical techniques applied to surface geochemical samples in the search for deeply buried mineral resources gained popularity in the late 1990s. Several commercial assay laboratories introduced their own selective leach methods, adding to the few established commercial methods at that time. Many of these laboratories promoted their methods with orientation data showing favorable responses to both precious and base metal mineralisation, concealed beneath extensive thicknesses of overburden. However, many explorationists remain confused about the utility of these geochemical methods. This confusion is due primarily to the lack of objective orientation surveys over significant mineralisation, comparing all commercially available selective leach methods and to the lack of a creditable theory explaining the formation of these selective leach anomalies. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. An orientation survey was designed to fill the first void û an objective survey over significant mineralisation. With the help of 17 mining companies and assay laboratories, an orientation survey was conducted over five significant covered gold deposits in Nevada, USA , representing over ten million ounces of gold. Hopefully the results of this survey will help provide fuel for those working on the second void û a theory to adequately explain the formation of these selective leach anomalies.

Jan 1, 2008

By Carter D

The Chairman of this afternoon's session is Dick Carter. This afternoon is the culmination of this conference. We've looked in the first session at regulation; in the second session at valuation techniques and this session we look at valuation in practice. Dick's involvement in the mineral industry has been wide ranging and distinguished. Dick has worked with BHP since 1960, when he joined BHP Steel as a commercial trainee. Dick holds a B.Comm. from the Newcastle University College of the University of New South Wales and was educated at the Australian Administrative Staff College and Harvard Business School Advanced Management Programme. During the past decade, he has headed the minerals group's Aluminium Divison, Resource Planning and Development, Non-Ferrous Metals and Business Development Organisations. Dick currently serves as Executive Director of BHP Gold Mines Limited and Managing Director of Ok Tedi Mining Limited. His experience covers Australian Manganese Company, Mineral Deposits Limited, Northern Rivers Rutile, Tasmanian Electrometallurgical Company Limited, Mount Newman Joint Venture, Worsley Aluminium and Carnilya Hill Joint Venture Operating Committee. His industry associations include the Executive Board of the Gold Producers Association, the Federal Executive of the Australian Goldmining Industry Council as well as the World Gold Council. Ladies and gentlemen, Dick Carter.

Jan 1, 1989

North Flinders Mines Limited (N.F.M.) is an Australian-owned mineral exploration and mining company based in South Australia. In the 1970's it researched the prospectiveness of the Tanami (central western region of the N.T.) for the identification of possible economic gold deposits. Having outlined the potential for such a deposit at The Granites (550 km. N.W. of Alice Springs), it marked out and in 1975 applied for the grant of eleven gold mining leases (G.M.L.'s) under the provisions of the then Mining Ordinance. This application was deferred by the Commonwealth Government during the time of the Aboriginal Land Rights Commission (Woodward), subsequent enactment of legislation and land claims. In 1980, the Walpiri and Kartangarurra-Kurintji land claim encompassing the G.M.L.'s, became Aboriginal land. It therefore became necessary for N.F.M. to negotiate a mining agreement with the Central Land Council (C.L.C.) represent- ing the Traditional Owners, before the G.M.L.'s could be granted. In August 1983, the C.L.C. and N.F.M. concluded an agreement to enable the grant of mining interests necessary for the devel- opment of The Granites Gold Project. In several ways this agreement is unique in That:

Jan 1, 1984

By B Ascott, J Kennedy, A White

At mines with low tonnes per vertical metre, like the Jundee Mine in Western Australia, operated by Newmont Asia Pacific, high development rates across multiple mining areas are critical to achieving the delivery outlined, or promised, in the annual business plan. The challenge is to deliver the short-term requirements while keeping in balance with the long-term strategic direction. Newmont Jundee has developed a system called æMine Planning by QuartersÆ that integrates the planning process with the business process in one end-to-end continuum. Short-, medium- and long-term schedules are reviewed and updated by applying four integrated subprocesses, which capture new information as it becomes available. The four subprocesses are: resource development planning û evaluating mineral resource,reserve development planning û preliminary design for new reserves,mine operating planning û final mine design for reserves, andmine production planning û detailed plans for stoping a proved reserve. Commercial mine planning software is used in these subprocesses to facilitate the flow of information into a central storage æhubÆ for uploading into the rolling business plan. A regular and consistent quarterly review helps to identify and qualify areas of business risk at an early stage, allowing time to plan for contingency and minimise the impact of the risk.

Jan 1, 2008