Search Documents

The Japanese Government promulgated the æLaw Concerning Special Measures Against DioxinsÆ on 16 July 1999 and it was enforced on 15 January 2000. This is a unique law specialised to protect the environment by the control of dioxin emissions from waste incinerators and several industrial processes. In this law, a few metallurgical processes other than waste incinerators are designated as æspecified facilitiesÆ emitting certain dioxins. Thus, emission standards for dioxins to the air were set for electric arc furnaces (EAF) for steelmaking, iron ore sintering, zinc recovery from EAF dust and aluminum recycle processes. In this paper, the inventory of dioxin emissions for Japan and the recent research and development to reduce emissions from those processes are introduced. Further, some details on the formation mechanism of dioxins and future subjects for effective control of their emissions are discussed.

Jan 1, 2002

By M Binks

This paper presents a case study that describes the selection, development, engineering and construction of a process plant for the biological oxidative pre-treatment of a refractory pyrite-arsenopyrite gold ore flotation concentrate. Prefeasibility and feasibility study resource modeling, metallurgical testwork, and environmental and engineering studies are outlined. Options considered for oxidation of the ore, which examine cost, risk, operability, recovery, engineering and environmental aspects are compared, with particular reference to pressure and biological oxidation. The BIOX« biological oxidation process was selected as the preferred oxidation process and the flow sheet for this process is presented. Selection of the BOIX« process resulted in special requirements for the feed preparation circuit, residue treatment and disposal, materials of construction and engineering. Use of a biological process in ore treatment also introduces particular process and engineering risks the management of which are discussed.

Jan 1, 2004

Ore reserve estimates form a basis for strategic mine planning at Argyle Diamonds open pit and alluvial operations. Most ore reserve statements are mainly concerned with resource tonnage and grade. Because diamond deposits are low grade, high value resources, diamond quality ($/carat) is also an important parameter. Relatively large variations in quality and/or grade can occur. These variations must be taken into account before the resource potential can be fully assessed. Computers (HP9000 and PC's) are utilised to compile resource inventories. Resource inventories are then ranked on an economic basis. This paper discusses the methods used to compile resource inventories and explains how these are then used to present ore reserve estimates in terms of resource potential.

Jan 1, 1990

The interfaces between the Broken Hill ore lenses and the enclosing wallrocks are, on a broad scale, parallel to metamorphic layering in the wallrock gneisses and quartzites. In detail, however, the concordant contacts are interrupted by piercement structures, formed by plastic injection of ore into the wallrocks during metamorphism.These discordant bodies vary from minor projections measuring less than I m long, to major ore shoots ("droppers") as much as 60 m long. The intrusive bodies consist of fragmented ore and wallrock in amatrix of recrystallised sulphides. Wallrock fragments have been altered to manganese-rich and calcium-rich mineral assemblages. The injected ore is enriched in sulphides compared with the parent ore, and there has been enrichment in a number of minor elements.Piercement structures formed during the waning phase of high grade metamorphism, when incompetent ore was injected plastically under pressure into the wallrocks, particularly at fold crests. Adjacent to the "droppers", retrograde schists developed as a result of shearing along the ore-wallrock interface.

Jan 1, 1976

By A T. Owen, F A. Benn, J D. Swift, D M. Labbett, A F. Grabsch

The AMIRA P266 æImproving Thickener TechnologyÆ series of projects has sought to provide a firm scientific basis for feedwell and thickener design, a requirement as pressures on water usage in the minerals industry increase. While advanced computational fluid dynamics modelling of feedwell processes has generated the most obvious and successful applications to improving the performance of operating units, such outcomes have drawn heavily on parallel studies into flocculation fundamentals. Central to this has been the development of a linear pipe reactor system that allows the kinetics of flocculated aggregate growth and rupture to be measured for thickener feeds under turbulent pipe flow conditions. This ensures much greater control of the intensity and duration of applied shear than is possible with conventional flocculation test procedures, offering insights into flocculation processes that would be otherwise hidden in time-averaged measurements.

Jan 1, 2009

Natural leaching of minerals has been recorded for some two millenia but surprisingly only in recent years has enough been known of the process for any serious design to be made. Copper has been recovered from natural mine waters since about the 17th century but again little progress was made in de- sign procedures until recently. Natural or dump leaching was started as a recovery process late in the 19th century and in the years up to the classic study of Taylor and Whelan in 1943 a series of impirical optimis- ations made it a valuable process for treating low grade or waste material. The biological nature of Sulphide leaching was proven by Colmer and Hinkle in 1947 and since then a large mass of data has accumulated on the microbiology, biochemistry, and response of ores to this form of attack. In spite of this knowledge and the vast amount of pract- ical experience available there are few recorded attempts to present methods of calculation or design procedures that can be used for setting up a leaching process. A framework is given here on which such procedures can be based and indications given of the inherent advantages and limitations of the process,

Jan 1, 1969

By M P. Sandy

Some Western Australian underground mines are challenged by very high stress gradients. This environment frequently results in poor induced ground conditions and damaging seismic activity. In some cases, rockbursting or squeezing ground has been observed as shallow as 250 m below surface. Very few mines operating at depths greater than 500 m experience no stress-related issues. As a general result of this difficult environment, there are a growing number of mines that are now challenged or have been closed by induced geotechnical problems. Often, the up-front savings or perceived advantage of an inappropriate mine plan may be entirely lost to the real cost of managing the hazards, or a write-down of reserves resulting from access difficulties will diminish the economic position of the mine. From an engineering perspective, it is best if stress-related hazards can be proactively minimised, because reactive measures offer less improvement in risk exposure. In this paper, some examples of sequencing techniques for managing difficult environments are contrasted with examples from mines where developing hazards have adversely affected production or the economic viability of the project.

Jan 1, 2003

Powercoal Pty Ltd operates eight underground coal mines in New South Wales and produces coal for both domestic power stations and the export market. Approximately 40% of total production is from continuous miners. Over the past five years, place change mining methods have been introduced to improve productivity from continuous miners. This has involved utilising the existing coal clearance system from the continuous miner to the ratio feeder using trailing cable shuttle cars.By late 1996 average productivity at Cooranbong Colliery using this system had plateaued at 800 tonnes per eight hour shift. A number of factors were identified to increase average productivity to 1500 tonnes per eight hour shift. An improved coal clearance system was one of the factors identified.

Jan 1, 1998

By Wilson A. F

The use of stable isotopic measurements as a technique for elucidating the origin and history of the water in hydrothermal fluids is relatively new. Recent studies have emphasized the importance of meteoric water in the formation of many hydrothermal ore deposits including many epithermal gold-base metal deposits which occur in faulted volcanic terrane. Other vein-type gold ores are be- lieved to have formed from fluids of magmatic or metamorphic origin and exhibit characteri stic 6180 values. These values also give information regarding temperatures and the degree of equilibrium. Preliminary oxygen data for some important gold deposits of eastern Australia are evaluated in the con- text of styles of mineralization.

Jan 1, 1980

By Semple DG, Leach TM

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as Zone C, is a measured 440,000t @ 17g/t Au and 46g/t Ag with an additional indicated resource of 120,000t @ 16g/t Au. A diatreme breccia localised at an intersection of structures, and a relationship of gold to base metal sulphides, are highly indicative of a porphyry association. Typical epi-thermal features such as crustiform banded quartz and quartz pseudomorphing. platy calcite are also present and locally contain lesser gold mineral-isation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100m strike. A fluid flow model suggests that mineralising fluids were sourced from the diatreme margins and migrated laterally along dilatant structures. Bonanza gold grades are derived through fluid quenching in the flexure between a hanging wall split which hosts much of the Tolukuma Hill resource and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting. Potential for more ore remains within the Gufinis and the 120 veins as well as in the outlying Prospects.

Jan 1, 1994

By C Yates, S Jobling, Z Y. Yang

The current trend in the UK towards the adoption of retreat longwall mining methods and the associated rapid development of the access drivages have exacerbated the environmental conditions experienced within these workings. There is a recognised need to improve the efficiency of the design and operation of mine ventilation systems in order to maintain an adequate environment and climate within these workings. Any improvement achieved in the quality, quantity and control of the delivered ventilation will assist in the provision of improved gas and dust dilution and climatic control. The paper presents an analysis of the psychrometric data recorded during the execution of a series of comprehensive climatic surveys conducted within two representative deep underground UK coal workings. The surveys were performed across two high production retreat longwall districts within UK Coal Ltd collieries. The surveys employed intrinsically safe psychrometric transducers and digital data-loggers to collect a continuous record of the mine climate over designated weekday production and weekend non-production periods. The transducers and data-logging units are capable of simultaneously measuring and digitally recording changes in the dry bulb temperature and the relative humidity at regular time intervals for extended periods of time.

Jan 1, 2005

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976

In 1976, The Zinc Corporation Limited Broken Hill set up a plant to re-process a hill of tailing (Mt. Keast) from the original treatment operations. With the likely disappearance of this source of feed in 1985, an investigation was initiated to determine what other feed sources might be available. This involved searching through old records and photographs as well as a subsequent drilling campaign. The paper briefly covers the history of treatment operations and describes, as a result of the information obtained, the likely future sources of feed.

Jan 1, 1983

By Chitombo GP

The proposed guidelines on vibration limits that have been circulated by the Australian Environmental Council, demonstrate the need for an extensive data collection and evaluation program to avoid the enacting of abritrary and costly legislation. The operational or practical influence of blast design and overall economic implications of legislation which further reduces permissible levels of ground vibration are discussed. In a typical blasting operation, blast sizes could become smaller and blasting correspondingly more frequent to meet pro- duction demands. Blasthole diameters and charge lengths could be reduced, increasing drilling costs and associated labour costs. Blast size however, is frequently controlled by factors associated with machinery, grade control, pit control, stope size, production contract levels and other factors which cannot be readily changed for operating mines. Blasthole diameters are frequently deter- mined by existing drilling equipment, length of holes (depth of ore or stope size), geological structure and other factors which are not easily changeable. Typical large scale open stoping and strip mining opera- tions are analysed as case studies. The effects of extreme leg- islative limits and the corresponding operational changes with respect to variations in production costs are discussed.

Jan 1, 1987

By Skaviniak M

Some better perspectives applying to the exploitation and dressing of polymetallic ores in the Banskfa. gtiavnica-Hod- rusea Ore District are supposed to be achieved after a suc- cessful investigation and proving there the existence of deep-seated mineralization as well as due to increasing de- mand for non-ferrous metals and consequently to higher mar- ket prices of those recently noticed. With respect to the present situation in mining and to the further technical development as well, a several times higher exploitation may be in this region expected, especially in the deeper .eated parts of the deposit. When solving the tasks of a complex economic exploitation over the whole region, consi- derable attention is paid to regional relations and impact studies (due to expected exploitation and ore dressing but also to very difficult problems of dewatering (drainage pro- blems-). It will be first of all necessary to find there an equilibrium between the consequences resulting from the re- naissance of mining industry and environmental requests un- dispensable for the city of Banska 9tiavnica and the other neighbouring towns in the vicinity of mining plants.

Jan 1, 1988

By Yoshii Y

Many kinds of shield machines are being driven in the soft ground of Tokyo metropolitan area. Tunnel alignments for underground power transmission lines are generally planned to pass under public roads where facilities, especially life-line facilities, are densely located. Therefore, it is frequently required to drive the shield machines along very sharply curving routes. This paper reports on the performance of the new shield machine - the Sharp Curve Excavation Shield Machine - developed by Tokyo Electric Power Co., Inc., which can freely drive along a much sharper curve than conventional machines. Some of features of the developed devices of this machine are, maximum flexing angle of 6.5 degree in all deirection at the middle of shield body, maximum bending angle of 3.5 degree in all direction at the cutter disc, and so on. This shield machine can there- fore drive along curve of minimum radius 15m. The machine was confidently applied to the const- ruction of tunnel in soft clay strata at N values 2 to 5. Outer diameter 3.7m. Length 202m. Horizontal curve; radius 15m, length 20m x 2. Vertical curve; radius 30 m, inclined driven up 29%. The behaviors of the shield machine, segments and surrounding ground were monitored during construction for safety and efficiency check of this machine.

Jan 1, 1987

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

By D Yuen, J A. D Connolly, T V. Gerya

Recent works suggest that dehydration of subducting slab and consequent hydration and partial melting influences the dynamics of mantle wedge. Plums originating form the subducting slab due to Rayleigh-Taylor instability are responsible for heterogeneous composition of the mantle wedge. Also, occurrence of partial melt in the mantle wedge can trigger dynamic processes like exhumation of UHP rocks in intra-oceanic settings or can influence characteristics of the subduction tectonic regime. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Dr David Dekker discussed the importance of a multidisciplinary approach to automation, the infrastructure required to support automation, and selecting the equipment for automation. Dekker stressed that automation involves a number of technologies. The mining industry is currently about part-way through the evolutionary process of achieving a fully integrated automation system. He pointed out that the final stages require parallel development of infrastructure such as mine communications. Technologies required for automation Automation systems consist of three parts: the gathering of information, the processing of that information, and taking action.

Jan 1, 1997

By Sun Yubo

A basic method for designing reasonable jig cycles for movable-screen jigs is presented in this paper. The reliability and effectiveness of the designed jig cycle was verified with tests performed on an artificial mixed material. An iron ore (12 - 100 mm) from Huashugo Iron Mine, Jiuquan Iron and Steel Company, was treated in the TJD-75 movable-screen jig using the designed jig cycle. A good result was achieved. The procedure presented here should provide a reliable technique for the design of a commercial movable-screen jig.

Jan 1, 1993