Search Documents

By the 1990's Australia could be the largest coal exporter in the world and one of the few industrialised countries potentially able to supply the shortfall in its domestic oil requirements by utilizing its oil shale and coal resources to manufacture synthetic oil. The major challenge to both industry and government in implementing the new role for Australia will be to ensure that their actions and policies enable the timely mobilization of resources needed to meet the potential demand for energy, both domestic and overseas. Australia's potential for coal production and exports and for the production of oil from shale and coal are discussed and the potential constraints to development Examined.

Jan 1, 1981

By Quinn P, Robertson G, Agar GE

The replacement of diphenylguanidine (DPG) for separating INCO Bessemer matte with a water soluble collector requires a frother since most collectors do not have frothing properties. The objective of this study was to identify a non persistent frother which produced a deep froth and collapsed rapidly, while maintaining acceptable metallurgical separation. Incremental rougher flotation tests failed to differentiate any metallurgical benefit through the use of a specific frother, so other tests were employed to identify the candidate frother. The equilibrium froth height and rate of froth collapse (froth stability) of several commercial frothers were evaluated as a function of frother concentration using a 'frothmeter' apparatus. Frothers evaluated were methyl isobutyl carbinol (MIBC), Pine Oil, triethoxy butane, Dowfroth SA1263, Dowfroth 250C, Dowfroth 200 and Allied Colloids CRNI-1002. Dowfroth SA1263 produced the largest froth height, and TEB had the greatest rate of froth collapse. Frothers with properties similar to Dowfroth SA1263 and Dowfroth 250 were rejected due to their persistent froths. TEB was rejected because it has a low flash point and Pine Oil could be a nuisance to add to a flotation column. Therefore, the preferred frothers were declared to be Dowfroth 200 or Allied Colloids CRNl-1002.

Jan 1, 1993

By Madgwick J. C

Bacterial leaching of museum grade chalcopyrite and chalcopyrite concentrates at low sorptive relative humidities (55-91 per cent rH) was demonstrated. Optimum release rates were 13 and 27 mg/gram/100 days copper (Cu++) at 91 per cent and 80 per cent rH and 12 and 33 mg/gram/100 days iron (Fe++) at 80 per cent and 73 per cent rH for concentrate and "pure" chalcopyrite respectively. The optimum copper release rates occurred between 73 per cent - 86 per cent rH and 30-40 mM acid concentrations. Bacterial copper leaching rates were some twenty times slower for emersed copper concentrates, at low relative humidity, compared with submerged cultures. Bacterial copper solubilization was almost quantitatively inhibited above 150 mM acid levels (< pHO.8).

Jan 1, 1984

This paper compares and evaluates the impact of income tax and value-added tax on the decision to explore for minerals or to develop a mine in four countries: Australia, Papua New Guinea, Argentina and Indonesia. Three aspects are considered in depth:- domestic tax rules applicable to mining projects;- taxation of foreign mining investment and foreign providers of expertise;- taxation of project finance (other than equity) from foreign sources.Specific tax issues discussed include tax deductibility of various costs, treatment of tax losses, special tax incentives, comparative treatment of various corporate structures, non-resident withholding taxes, and tax costs of various forms of project finance. The paper also illustrates the comparative impact of income tax on rates of return by means of a simulation of a mining project in each of the four countries. The simulation demonstrates why the highest rate of return may be obtained in Argentina and the lowest in Australia.Relevant features of the income tax systems in each country (at 15 February 1990) are summarized and compared in several tables annexed to the naner.

Jan 1, 1990

By Singleton T

Increasing world competition puts pressure on sales volumes and prices. This in turn reduces potential profit margins. This in turn increases the focus on costs.Increasing demands on quality and service puts pressure on delivery performance - the right product at the right time. This in turn reduces the scope for errors and delays - and this in turn increases focus on equipment reliability. In the mining industry, both costs and equipment reliability have one significant thing in common - they are driven substantially by maintenance.

Jan 1, 1998

By Craw D

The Southern Alps in the South Island of New Zealand are currently rising rapidly as a consequence of continental collision along the Pacific-Australian plate boundary. Rapid uplift has resulted in a major thermal anomaly in the shallow crust beneath the alps. Alpine topography and associated intense precipitation, coupled with the thermal anomaly are responsible for vigorous combined topographic/convective circulation of water through the shallow crust.

Jan 1, 1995

By M Magee, D Way

The Mount Isa Copper Concentrator was commissioned in 1973. In 1991, two autogenous grinding mills were installed replacing two stages of crushing, one stage of rod milling and one stage of primary ball milling. The cyclone overflow P80 of the secondary ball milling circuit was reduced to 120 microns due to the increased operating power in the AG/SAG mill circuits. A study of the mineralogy of the milled products and the plant flotation recovery indicated that the installed secondary grinding energy was more than what was required for adequate liberation of the chalcopyrite and half of it had potential for more effective use elsewhere. Halving the secondary grinding energy meant only one of the two secondary ball mills would be needed. The predicted saving in operating cost of one less ball mill was more than two million dollars per annum. This paper summarises various plant trials that were conducted in the Copper Concentrator to decommission one of the two secondary ball mills.

Jan 1, 2004

Where tunnel rounds are based on the burn cut, faster advance could often be achieved by increasing blasthole diameter from (the conventional)

Jan 1, 1981

By S McKnight, S Hall

Much of the research regarding the use of bacteria for the oxidation of sulfide minerals has been conducted using pure bacterial strains or synthetic minerals, often under ideal conditions, which does not reflect the conditions commonly encountered in commercially operating plants. This has also led to much conjecture as to the exact mechanism by which bacteria are able to enhance sulfide oxidation and as to which species of bacterial microflora are the most dominant. Recent advances in 16S rNA sequencing has confirmed that many of the bacterial species once thought to dominate commercial oxidation circuits were simply more willing to grow under the culturing conditions used and may only play a minor role in the oxidation process (Rawlings, 2002). Consequently this research will look at bacterial oxidation under conditions more reflective of commercial operations, focusing on the presence of organic carbonaceous material within a refractory sulfide orebody to be sourced from the Fosterville deposit of Perseverance Corporation Limited.

Jan 1, 2004

By J H. Baker, P G. Beadle, J P. O&apos, Brien

In 1974 a preliminary study of the refractories industry in theRepublic of Indonesia was completed by Crown Lynn Consultants, a subsidiary of Cerarnco Ltd., on behalf of the Indonesian and New Zealand Governments. As a result of recommendations arising from that study the two Governments commissioned, in 1976, as a Bilateral Assistance project, an investigation into the potential of the refractories industry in Indonesia. Ceramco Ltd., was retained to carry out the study on behalf of the New Zealand Government. The Directorate-General of Chemical Industries, Directorate of Silicate Industries administered the project on behalf of the Indonesian Government. Indonesian counterparts to the New Zealand study team were provided by the Directorate of Silicate Industries.

Jan 1, 1978

Consideration was given to the.applicab on of a solvent extraction circuit to be'included in the process'for the-recovery of a high grade product from.:-the Rum Jungle Creek.South uranium ore body.The economics of two alternative processes, firstly the Eluex process which uses an ion exchange process followed by solvent extraction.-of a.high grade sulphuric acid eluate, and secondly a process using direct solvent' extractioh of pregnant leach liquor, were studied. There was a small cost advantage favouring the Eluex process but when other factors were considered, the installation of a direct solvent extraction process appeared the better long term investment. A solvent extraction plant was installed at Rum Jungle in 1962.

Jan 1, 1963

George Fisher Mine, near Mount Isa in northwest Queensland, has been producing Pb-Zn-Ag ore since the late 1980s. It consists of two separate underground deposits, George Fisher South and George Fisher North. These two deposits are drilled and modelled separately but are crushed and hoisted as a single stream. The Pb-Zn concentrator in Mount Isa processes ore from George Fisher Mine and Black Star Open Cut, with production also from the Isa Lead Mine until January 2006. This paper outlines the steps involved in setting up a robust reconciliation system for George Fisher Mine, in conjunction with requirements of the Pb-Zn concentrator, Black Star Open Cut Mine and the Mount Isa Lead Mine. Good quality input data and commitment to training have contributed to establishing a robust and effective reconciliation system. Reconciliation data has highlighted several other continuous improvement opportunities.

Jan 1, 2006

By Dight P. M, Dugan K. J

Design approaches for the artificial support of open pit walls have been reviewed and the main factors affecting support performance have been identified. An example of passive support in a potentially unstable pit wall has been used to demonstrate the importance of slope displacement as part of the support design process.

Jan 1, 1989

Looking back 25 years, the role of the drill and blast engineer in an Australian mine seemed relatively simple, with the primary focal points being scheduling of the drill rigs, oversize control, and budget control with respect to consumption of both explosives and drill consumables. The choice of explosive selection was relatively simple, though many mines were becoming involved in trials of slurry explosives, emulsion blends, and low density ANFO blends. Guidelines to assist the engineer towards specific fragmentation targets were scarce, environmental constraints were light, and computers were rarely found on the desks of any mining engineers. Wall control blasting was in its infancy, with the bulk of attention being given to appropriate slope design and little real attention given to factors such as explosive distribution, and optimum delay timing and sequencing. Quantitative measurement of blasting performance was rare. The science of blasting, for fragmentation control, wall control, and environmental impact control was about to be born, and was heralded in those years by intense efforts by the explosive manufacturers and a proliferation of research centres throughout the world. Since the early 1980s, the role of the Australian drill and blast engineer has gone through a major metamorphosis, and currently requires a greater depth of scientific understanding than any other specialisation within mining engineering.

Jan 1, 2004

By McMullen P. H

Mining of copper ore at Mount Lyell has been continuous since 1893. The operation has always been marginal and the depressed copper Market over the last decade has seen mining continue on the basis of a series of short term plans. In 1985 it was determined that the mine would close in 1989 on completion of the 40 Series mining block. Significant changes in the value of the Australian dollar in 1986 and the subsequent effect on profitability dictated a review of the Company's operations. Lower level ore reserves, mining methods and ore handling systems were re-examined and a plan proposed for mining of the 50 and 60 Series mining blocks. The improved economics of this plan, together with workforce and State Government initiatives resulted in an extension of mine life to 1994.

Jan 1, 1988

By R Balusu, P Humphries

In combination with detailed field studies and goaf gas characterisation, computational fluid dynamics (CFD) models have been used to develop optimum and effective strategies for inertisation during longwall sealing operations to achieve goaf inertisation within a few hours of panel seal-off operation. This study has combined detailed analysis of the performance of various inertisation field trials together with CFD modelling results of different inertisation operations in order to develop the optimum inertisation strategies. A number of parametric studies were conducted on the base case CFD models that had been calibrated and validated based on the information obtained from previous inertisation studies and goaf gas monitoring. These studies included changes in inert gas injection locations, inert gas flow rates, seam gradients, and different inertisation strategies to investigate their effect on goaf inertisation. Studies indicate that the strategy of inert gas injection through the MG seal was not as effective as the alternative strategy of inert gas injection at 200 m behind the face. Innovative inertisation strategies have been developed and subsequently implemented at an underground coal mine in Australia. Further investigations have been carried out in the development and demonstration of proactive inertisation strategies with the objective to suppress the occurrence of spontaneous heatings in active longwall faces, in particular under unexpected scenarios such as during slow retreat/face stoppage due to difficult geological conditions. Initial trials at two Australian longwall panels have demonstrated the great potential of this practice to contain the onset of heatings in the goaf.

Jan 1, 2005

By Sparrow G. J

In a recently completed AMIRA project, 20 samples were searched for gold mineralisation using the automated location facility (ALF) for rare phases on a scanning electron microscope in the CSIRO Division of Mineral Products, Melbourne. The samples were submitted by mining companies in Australia, and Papua New Guinea, and included crushed ore samples, cyclone overflow and underflow products, a flotation concentrate, and 12 tailing samples. Their gold contents ranged from 600 to 0.2 g/t An. Native gold and gold minerals including a gold telluride, gold-silver tellurides, and a gold bismuth mineral, were located in the samples as free grains and associated with other minerals such as pyrite, magnetite, hematite, ankerite, copper sulphides, silicate minerals, and quartz. In the highest grade samples, both micron sized and 200 ¦m grains of gold were found with ALF. It would be difficult to locate such d wide size range of gold in a manual search. Gold mineralisation was located in the tailing samples assaying 0.4 g/t An and higher. In several tailing samples coarse grains of native gold over 40 p.m in size were located. One grain was estimated to have contributed 40 per cent of the gold in the sample. As well as locating gold mineralisation, the ALF examination resulted in the identification of uranium, mercury, and bismuth minerals in the samples. Knowledge of the distribution of these minerals in processing streams could be important in the operation of a concentrator.

Jan 1, 1992

By King ND

This paper presents an economic study comparing two gold recovery processes, zinc precipitation (Merrill-Crowe) and carbon-in-pulp (CIP). Capital, operating, and gold losses costs from an actual CIP plant study are compared to costs developed from a hypothetical Merrill-Crowe process flowsheet. ' Results indicate an overall economic advantage to CIP over Merrill-Crowe for plants processing slurries within the range of the five gold solution grades selected for this study.

Jan 1, 1982

From a personal view that encompasses both research and assessment of major projects the author outlines the two competitive pressures that will force more rather than less metallurgy viz the increasing difficulty in purchasing the latest overseas developments and environmental concerns. This paper then goes on to argue that Australian metallurgy or more precisely process engineering may be in a unique position to deliver the required results.

Jan 1, 1993

By Scott A

This paper summarises some of the results of the ACARP-JKMRC project 'Optimisation of Dozer Operations in Open Cut Mines'. The work has involved an industry review, design and conduct of field trials of coal seam preparation using dozers, nume

Jan 1, 1998