Search Documents

By Menne DM

The carbon-in-pulp (CIp)process has become well accepted and firmly established in the gold industry of South Africa and, at this stage, six large CIP plants are treating close to I million metric tons of material per month. Many small operators are also using CIP and additional large plants are either nearing completion, are on the drawing boards,. or are being considered. The programme of testwork that preceded the acceptance of the CIP process in South Africa was conducted over some eight years and has been previously described'-7. With the start-up of the President Brand CIP plant on 'calcine' in July 1980 and that of the Western Areas CIP plant on repulped filter residues in September 1980, the emphasis on the CIP process switched from pilot plants to these large plants - and has largely remained there. As it has started up, each new CIP plant benefited from the experience gained and the developments made, on earlier plants but, since so few plants have so far been established in South Africa, each new plant and each new design has revealed a further set of conditions to be met and problems to be overcome. However, in the highly collaborative atmosphere of the South African gold-mining industry, the results and observations from the operation of these first plants were shared by all mining groups. This paper will attempt to describe typical developments on, and results obtained from, these new large plants, and will incorporate significant results from the earlier laboratory and pilot-plant investigations.,

Jan 1, 1982

By Amelunxen R, Finch JA

Flotation columns represent an important addition to flotation practice. Columns have largely replaced. conventional machines in molybdenum cleaning in Canada. Columns have been successfully tested on bulk copper/molybdenum cleaning at Gibraltar Mines Ltd. A rougher cleaner/scavenger cleanercombination was shown to be capable of giving higher grades and recoveries compared with three stages of conventional cleaning. A control strategy for the columns has been developed. An interaction between gas hgldup and wash water rate has been exploited to control performance.

Jan 1, 1985

By Sheng X. L

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts. collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger..

Jan 1, 1992

By Sorokin M. L, Komkov A. A

Flash smelting of nickel sulphide concentrate has been practiced at WMC's Kalgoorlie Nickel Smelter for 20 years. The mineralogy of the concentrate from the original mines was particularly suited to this process. However, taking a strategic view, potential new processing routes should be fully evaluated as possible replacements for the current technology. The Vanyukov process has been under development in Russia for the past 40 years and has been successfully applied on a large scale to the smelting of copper concentrates, at two locations - Norilsk and Balkhash. The potential for the application of the Vanyukov process to the smelting of nickel concentrates offers a number of processing advantages, including smaller reactor and decreased dependence on fuel oil. This paper reports on preliminary investigations into the application of the Vanyukov process to the smelting of nickel concentrates. At this stage the investigations are limited to semi-quantitative comparisons and modelling studies.

Jan 1, 1992

A portable surface impedance meter has been tested extensively over a wide variety of geological formations both in Australia and elsewhere. It has proved a useful geophysical too] for relatively shallow mapping (i.e less than 100 metres depth) of faults, intrusions, dykes and conductive ore veins and can be used as a depth probe for overburden and glacial ice. Case studies involving coal seam mapping at Collide (Qld. Australia), galena ore vein location at Zeehan (Tas. Australia) and glacial ice probing on the Brewster Glacier (South Island, New Zealand) are detailed. The first results of a similar unit using a lower frequency with consequential increase in depth of penetration will be presented. The application of VLF measurements to monitor blasting in mines and in the location of earthquake epicentres will also he introduced.

Jan 1, 1987

By Yang RL, Bailey ML

During overburden blasting operations in dragline pits, coal edge losses along the lowwall edge of the new pit are often experienced. In tonnage terms, losses can be significant. With the thick seams at Callide Mine, 20,000 tonnes of coal can be lost along a 600 metre pit. In addition to the immediate dollar value of the coal, replacement of this coal (from which overburden has been removed) will be from higher ratio and higher cost pits in the future. Unit costs of production for the remainder of the coal uncovered in the current pit increase. Experiments involving variation of blasthole inclination and/or amount of standoff on the front row of blastholes have given no significant improvement in the coal edge loss control.

Jan 1, 1988

Production scale experiment study was carried out in a limestone open-pit for testing the theory and method proposed by the author(Zou, 1987). The results of experiments indicate that the mathematical model and computer programs, which include the consideration of both the three dimentional distributions of the weak planes and the energy densities of explosion stress waves, reflect the physical process of rock bench blasting quite well. The predicted fragment distributions coincide well with the practical fragment distributions measured with the photo-image analysis method proposed by the author(Zou,1989). The paper "A Three Dimensional Mathematical Model for Calculating the Rock Fragmentation by Bench Blasting in the Open-pit"(Zou,1987), which was published in some conferences and journals, has interested some scholors and researchers. In order to test and improve the model, a group of production scale experiments were carried out in a limestone open-pit during 1986-1987. The procedure and results of the experiments are illustrated in this paper.

Jan 1, 1990

By Wang QP, Quan YH

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

By Grady PO

The longwall panels at Clarence Colliery have experienced intermittent sudden weightings on the face that have caused some production delays. These weightings have typically been more severe on the wider faces. A program of surface subsidence and extensometer monitoring was undertaken above Longwalls 4 and 5 to investigate the behaviour of the overburden strata during longwall extraction on two faces of different widths.The monitoring indicated that a dome shaped zone of large downward movement extends up into the overburden strata to a height equal to about the panel width.

Jan 1, 1998

An increase in the silver to gold ratio with increase in depth in the main ore shoot of the Crown- Crescent lode in the Emperor gold mine, Fiji, was found to be due mainly to vertical zoning of gold-silver tellurides. The zoning resulted from

Jan 1, 1980

By Turner T. M, Jorgensen F. R A

The tendency of the concentrate to ignite was studied using four techniques, namely, laminar flow furnace, fluid bed, thermal analysis and boat-in-furnace. Exothermic activity occurred at two temperatures: minor activity in the vicinity of 200¦C, major activity at 330-350¦C. The low temperature reaction was due to the ignition of a small amount of free sulphur while the major activity was associated with the ignition of the sulphide minerals, notably pyrite. To avoid ignition of the sulphide minerals, the gas temperature should not exceed 300¦C and the oxygen content of the gas phase should be as low as possible. It was shown that little of the arsenic in the concentrate entered the gas phase during drying.

Jan 1, 1987

By Fisher AEJ

On Sunday morning 7th November, 1976, at approximately 2-25 a.m., smoke was discovered issuing from the 1912 m long belt drift at Appin Colliery. A Clouth steel cord rubber belt approximately 940 mm in width had been installed in the drift in 1963 on the basis that no fire resistant steel cord belt was then available to operate on a single lift at the load and on the 160 gradient of the drift. Investigation showed that the belt drift was on fire and the usually downcasting drift was upcasting. Immediate fire fighting and rescue operations were instituted and the drift was sealed off. High expansion foam was pushed into the drift from the surface and the fire was brought under control. Recovery work resulted in the fire being put out and the drift open for walking traffic by, S-P0 am., on Wednesday 10th November, 1976. lie experience gained during the fire fighting and recovery operations led to recommendations in regard to future use of high expansion foam.

Jan 1, 1981

The control of industrial grinding circuits in Australian concentrators has been practised for many years in one form or another. Some have established simple feedback loops in areas such as fine ore bin feeders (tonnage control), mill pump sump levels (flow control) and water additions (density control). There are also some sophisticated systems which infer circuit product size using complex measurements of mass flaws and water additions in the circuit and attempts are made to control those flaws to produce a constant circuit product size. The inferred size method in Australian concentrators has become firmly entrenched in the last ten years and control techniques involving the use of direct size measurements with reliable on-stream sizers have been Ignored.

Jan 1, 1983

In the Illawarra District of New South Wales, Mines were traditionally developed from the seabord. The advantages were close access to the working faces and a minimal depth of cover. Travelling times to the working faces have become prohibitive in many cases due to progressive westward development of the mines. As a result, additional vent- ilation shafts were sunk to service existing mines and new mines were established west of the Illawarra escarpment. Mining operations west of the escarpment are now being conducted at an increasing depth of cover and can be effected by gas related problems such as high seam gas emission rates and gas outbursts.

Jan 1, 1983

By Johnstone RD, Rattenbury MS

RACE Quartz-calcite veins containing Au, As, W, Cu, Pb, Zn and Fe cross-cut Alpine Fault- related structures in the Alpine Schist of South Island, New Zealand. These veins, and some other related veins have been deposited by metamorphic fluids at 250¦C to >320¦C at pressures of a few hundred bars. The fluids were very variable in composition, with 0 to 50 mole % CO2 and 2 to 18 wt. % NaCl equivalent. Penetration of hot metamorphic fluids to shallow levels in the crust was facilitated by rapid uplift of hot rocks at a compressive plate margin. Fluid immiscibility at shallow levels caused concentration of salts and metals into the aqueous phase. Gold precipitation was caused by reduction by pelitic country rock and/nr dluILion by other aqueous fluids.

Jan 1, 1987

By Hefter G. T, Singh P

The use of sulphur dioxide (SO2) as an anode depolarizer in place of traditional oxygen evolution reduces the energy costs of copper electrowinning. This paper reports the effect of various metal ion impurities, which are usually present in th

Jan 1, 1998

By Russo S

Metals Refining Operations Pty Ltd (MRO) began refining gold in PNG in 1991 and has undergone continuing growth since then in servicing an everchanging and growing market. MRO's ownership combines PNG Government interests and Golden West Refining Corporation Limited as operator.Features include a very diverse range of suppliers, a full range of technical methods and challenges and the financing and marketing responses unique to a developing country. These areas are examined and documented with special emphasis upon the service needs for the gold industry and future trends and challenges are discussed.

Jan 1, 1997

By Floyd JM

Pilot plant trials showed the effective ness of the submerged lance SIROSMELT technology for altering the composition of iron blast furnace slags as a preliminary step to produc- tion of formed materials. Mixtures of oil and air were injected into a bath of liquid slag to provide the heat required for melting the additives and to provide very turbulent conditions which resulted in complete dissol- ution of added fluorspar within one minute and almost complete dissolution of silica in two minutes. Sulphur lost during injection was readily made up by addition of pyrite or pyrrhotite. A stable foam could be readily made and broken down and the foamed slag appeared suitable for extrusion or forming into shapes.

Jan 1, 1979

By Showers JAF

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988

This paper presents a summary of the technical achievements of the Port Pirie Smelter in 100 years of lead smelting and refining. It also aims to give where possible the reasons or circumstances that led to the achievements. The major achievements took place in the areas of sintering, blast furnace, copper drossing, copper recovery, lead refining and slag fuming.

Jan 1, 1989