Search Documents

By Rodney R. Koch

The phys ica l properties of gold should faci li tate its detection. However, the average concentration of gold in the ea rth's cru st precl udes the ability of geophys ical methods to detect the metal directly. In order to effectively pursue geophys ical detection and location of gold mineralization there must also be geological input - i.e. a model. This will lead to the selection of the appropriate geophy ical techn ique(s) in the fo llow-up programs. Interpretation of the fie ld survey data is of con iderable importance in expl oration geophys ics. Analytical techniques such as cont inuation, fi ltering, and spectral analys is, are now routinely empl oyed in the analys is of survey data to aid the interpretation process. The uccessful application of geophysical methods and the use processing techniques is demonstrated by two recent Saskatchewan discoveries. The first, the Star Lake 21 Zone, with reserves of 230,000 tons grading bener than 17.14 git Au associated with a disseminated sulphide quartz-bearing shear zone yielded geophysical anomalies that were distinctive, obvious, and would have lead directly to its discovery. The econd , the Laurel Lake Prospect, with ore grade intersections of 28.0I git Au and 52 .46 git Ag· over 5.49 m, resulted in numerous geophysical anomalies. However, none of these anomalies demonstrated association with the mineralization until processed results indicated that structural features crosscuning regional trends were important cont rol mechanisms for the mineral ization.

Jan 1, 1986

By Karina Forster

Rock mass characterisation is a critical component of effective stope design. Unexpected excessive stope dilution or uneconomic stope sizes can be the result of rock mass characterisation that is not representative of actual stope conditions. Comprehensive characterisation of the rock forming the stope hanging wall, back, ends and footwall is best done by a rock mechanics or ground control expert, however, this is time consuming and is often limited by available access. There are two general approaches for characterising a stope hanging wall for dilution estimating. Detailed classification and mapping data can be collected in local areas where good exposure is available. Personnel, exposure and time are usually not available to do a thorough analysis for all stopes. The stope hanging walls are then broken into lenses or domains and similar conditions are assumed for each area. The second approach consists of using readily available data such as RQD. Other rock mass properties which influence hanging wall behaviour are estimated based on back analysing a few case histories. Stope design is then based on the variability of the one parameter, such as RQD, that is consistently measured for the rock mass surrounding the ore body. This paper presents a third approach which looks, in depth, at the interpretation of geological core logging data for rock mass characterisation. Several rock mass properties that influence stope design, such as joint alteration, rock mass strength, joint spacing and orientations, have been linked to data collected by the mine geologists. This drill hole logging data was calibrated against underground mapping and used to back analyse the dilution prediction for mined-out stopes.

May 1, 2006

By J. G. Bennett

Coal consumption has increased globally by 57% over the last ten years. Underground mining typically provides coal of the highest calorific value and accounts for the greatest proportion of production. Despite a negative environmental image and indeed impact, this industry appears likely to thrive on the global scale for many years to come. Such mining consumes large amounts of electricity with implications for carbon dioxide emission at power plants and emits substantial quantities of the powerful greenhouse gas methane. In response to this significant carbon footprint, the European Union has funded research to examine the potential for a range of improvement technologies in a project entitled Low Carbon Mine Site Energy Initiatives (LOWCARB). Coal properties related to seams and mines, together with longwall characteristics, provide the basis for research into modelling optimally efficient methane drainage with a view to assisting mining as well as maximising electricity generation at surface and hence oxidation of the methane. Possible systems for the oxidation of very low concentration methane in ventilation air, which contributes the greatest greenhouse gas impact due to the volumes emitted, have been studied and modelled. Simulation and investigation of intelligent optimisation of electricity demand patterns provide the basis for reducing the demand peaks at mines and hence the cost and ultimately the carbon footprint of a mine, while specific investigations have been undertaken into ventilation efficiency at an unusually challenging mine and simulation of mine water pumping in order to develop an innovative method to monitor pumping systems efficiency. For post-mining use, the potential of disused shafts for compressed air energy storage to improve the operation of future electricity grids with high renewable energy penetration by reducing peak generation capacity requirements has been studied. While underground coal mining will always by definition be related to a significant carbon footprint, this paper provides an overview of a set of initiatives that can make a positive environmental impact while controlling costs across a huge global industry.

Aug 1, 2013

By Glenn K. Nolan

"Today, more than any other time in recent history, aboriginal communities are looking for ways to be understood as more resource development companies continue to explore and develop Canada's vast resource potential.Recent Supreme Court rulings have affirmed the need to engage aboriginal communities early on in resource development projects. There are many conflicting ideas on how, who, and when to engage. Given the large number of communities and varied cultures, each resource development company must equip itself with a better understanding of the people they are planning to work with.The lecture will begin with a basic historical perspective on treaties and the various societies across Canada. We will also explore the current situation many communities find themselves in today. Building a meaningful relationship with a community is the foundation for a lasting partnership. Every community is unique and every approach to engage communities must be just as unique. The lecture will outline some basic steps that can lead to a better relationship building process between the communities and companies."

Jan 1, 2008

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

By Júlio C. Lúcio

Consider the case of a mining company with N investment opportunities in projects of different commodities. The problem is: since the company has limitation of capital, equipments, technical staffs, etc, what is the best portfolio of production projects in order to maximize expectations from shareholders? In the no-longer past, the traditional method for the selection of portfolio of projects was the rank-an-cut method. But, this does not properly account for the risk to which the company is exposed. The Markowitz?s Mean-Variance is an advance because the risk of the NPV can be estimated at the level of the company or even division of the corporation. The final product of the Markowitz?s model is the efficient frontier, in which, the manager can clearly understand the maximum return from existing assets and the associated risk level - but this model does not recommend which one is the best portfolio. In this paper we present a model to select the best portfolio considering not only economic indicators, but also requirements of production, constraint in investments, etc. We show that if investors are diversified, managers should select projects with highest return, regardless of risk. However, in practice, if bonuses of managers are tied to their performance, the choice for portfolio with lower return and risk can happen. Numerical application considering typical portfolio of large mining company is used as example.

May 1, 2009

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By A. W. Stradling, M. J. Fairweather

"The selective flotation of lead, zinc and iron sulphide minerals is key to the economic performance of concentrators treating zinc-lead ores. Diagnostic metallurgy is a tool to quantify mineral behaviour as a function of particle size and liberation. The result of such analysis may be used to select preferred strategies to improve metallurgical performance. The zinc flotation circuits at three Teck Cominco operations: Sullivan, Polaris and Red Dog are compared here. This paper analyses operating data from each of these circuits. The effects of mineralogy and performance by particle size are emphasized. Metallurgical performance at these three concentrators varies substantially. Liberation size is the major factor in determining metallurgical performance. Complex mineralogy requires a fine grind to achieve effective liberation. Fine grinding results in offsetting decreases in concentrate grade through entrainment. The economic treatment of complex fine-grained deposits requires optimisation of regrind size for liberation without unduly compromising concentrate grade through gangue entrainment.INTRODUCTIONUntil recently Teck Cominco Metals Ltd. operated three mines treating zinc-lead ore. In order of increasing mineralogical complexity they are: the Polaris Mine on Little Cornwallis Island in Nunavut in the eastern Arctic, the Sullivan Mine in southeastern British Columbia and the Red Dog Mine in northwestern Alaska. Both the Polaris and Sullivan Mines have recently ceased to operate due to depletion of ore reserves.The ore type and associated gangue, mineralogy and iron solid solution vary significantly between these deposits. Table 1 summarizes some of the important differences"

Jan 1, 2003

By A. L. Mular

"IntroductionThe mining industry has made slow but steady progress toward the automation of mineral processing plants over the last 35 years. The stimulus to automate is associated with important economic and hidden benefits, so that today, the latest in instrumentation and technology is being employed.This chapter assesses the status of instrumentation justified economically, defines levels of control and certain fundamentals of feedback control loops, describes typical sensors employed in concentrator circuits, summarizes control strategies employed therein, and briefly highlights trends in integrated plant control.Current Status of AutomationAs early as 1948, the mining industry began to show interest in automation, probably because of its close association with the petroleum industry. By 1958, some regulatory control had been achieved in various sections of a concentrator, particularly in crushing circuits. Successes were attributed primarily to the reliability of sensors employed in the corresponding control scheme. By 1961, computers had appeared on the scene, initially, for data logging purposes.From 1958 to 1965, very few new control strategies had been implemented. Guidelines in vogue at this time appeared to be:- Install proven automation, unless a good instrumentation department exists at the concentrator.- Do not bite off too much instrumentation at one time.- Do not purchase on price alone; instrumentation must function in the concentrator environment.- Do not purchase automatic control equipment to be fashionable.Such guidelines were employed1 because of a lack of: (a) quantitative process knowledge, (b) reliable primary sensors, (c) initiative to try something new, (d) trained personnel, and (e) understanding that older concentrators could justify automation in many situations."

Jan 1, 1989

By H. P. Jacobi

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 65 miles east of Hay River, N.W.T. on the south shore of Great Slave Lake.The milling operation started in the fall of 1965 with a capacity of 5,000 tpd. An addition was put into operation late in 1968 to bring the nominal capacity up to 8,000 tpd. The present milling rate is 11,000 tpd.With a feed grade of approximately 2.9% Pb and 6.0% Zn the annual concentrate production amounts to roughly 130,000 SDT of lead concentrate and 370,000 SDT of zinc concentrate for a total of 1/2 million tons of product.This tonnage is moved by railroad. Pine Point is served by the Great Slave Lake Division (G.S.L.) of the Canadian National Railways which connects to the Northern Alberta Railway System (N.A.R.) at Roma Junction, at Peace River, Alberta. The system in turn connects to the CNR and the CPR in Edmonton, Alberta. From here the concentrates move inland chiefly to Trail, B.C., with some shipment to other Canadian and U.S. smelters, and to the port facilities of Pacific Coast Terminals at New Westminster, B.C. for offshore export.This paper will focus on the problems associated with the movement of lead and zinc concentrates from Pine Point to port facilities on the west coast."

Jan 1, 1975

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

By Pravin Kumar

Goldcorp Inc.?s Red Lake Mine (RLM) is situated in the Red Lake Mining District, a history rich North Western Ontario mining community. Red Lake Mine formerly known as the Dickenson Mine has experienced various degree and type of bursting since the 1960?s. During the 1960?s burst were common in shrinkage stope box hole pillars. After discovering the High Grade Zone (HGZ) between its 30th and 39th levels, the mine has changed its mining method to mechanized cut and fill with cemented paste fill. The rock mass at RLM is mainly massive basalt-ultramafic and behaves in a manner consistent with massive brittle rock. This paper presents the use of empirical and numerical design techniques. The use of the Span versus RMR graph to determine critical stope spans at RLM and the use of numerical design techniques to determine the stability of the sills and post pillars. Selecting of a sill pillar dimension is illustrated using four different failure criteria?s. The four failure criteria are m & s failure criteria, the Pillar Stability Graph, deviatoric stress ???-?3), and induced stress level criteria ?1 /UCS, which are calibrated to RLM?s ground conditions. A wide range of case histories has been studied ranging from stable to highly burst prone ground conditions in order to calibrate the failure criteria to observed conditions and quantified to local micro seismic system.

May 1, 2002

By Denis Thibodeau

his paper describes a study of an altered mining extraction and the resulting Rockmass response at VALE?s Creighton Mine. Typically, the deep mining zones have strict stope extraction guidelines to ensure safety and productivity; however, these guidelines offer low flexibility or few options for stope sequencing. The 402 O. B. being in a good rock mass, at moderate depth and stress regime at Creighton, offered an opportunity to drive a more flexible mining sequence with stopes and a pillar. A three-phased approach was used to mitigate risk of the mining plan: 1- Numerical modelling to fully anticipate rock mass response to the proposed mining sequences. 2- In situ seismic monitoring to collect stress and seismic activity data. 3- Analysis of the in situ data to correlate to the modelling results. The creation and the extraction of a pillar in the 402 O. B. was successfully completed. The recorded seismic activity agrees well with the numerical modelling since most of the seismic activity is localised in the hangingwall where the deviatoric stress corresponds to an early damage process. The moderate levels of deviatoric stress cause localised failure with low level of seismic activity.

May 1, 2013

By Victor R. Eyzaguirre

Cerro Verde is one of several large porphyry-type copper deposits in Southern Peru. The copper occurs as primary sulphides, with a significant oxide capping. The exploitation of the deposit has been correspondingly divided into two stages, the first consisting of copper production from oxides, and the second from sulphides. Minero Peru successfully started the Stage I plant in June of 1977 with the first production of electrowon copper cathodes. This paper is essentially devoted to a description of the Stage I process, which can be summarized as follows: Ore is trucked to the primary crusher, where it is crushed to 225 mm and conveyed to a coarse ore stockpile. Ore withdrawn from the stockpile is secondary crushed to 65 mm, conveyed to a truck loadout bin, loaded into trucks and driven to the leaching pads. Ore is placed on the pads in lifts and sprayed with sulphuric acid solution to dissolve the copper. Copper-bearing solution forms a pond behind a dam at the lower end of each pad and is pumped from there to the solvent extraction plant. Copper is extracted from the leach solution into an organic phase and is then stripped from the organic phase to form a purified concentrated copper solution suitable for feed to electrowinning. In electrowinning, the copper is finally recovered as cathodes suitable for sale as refined copper.

Jan 1, 1978

By R. Matusewicz

The key drivers for the copper smelting industry are a complex mix of economic and "human" factors which combine to drive technology in new directions and can provide a strong indication of future industry trends. Recent examples have been the drive to achieve increased scale of production and resultant cost efficiencies by using a single furnace high intensity smelting vessel, and the broad acceptance of Top Submerged Lancing (TSL) technology for this duty. The development and adoption of continuous converting processes to counter the increased pressures faced by the Peirce Smith converting process is another example of the need for innovation. This paper discusses the merits of the continuous converting process, describes how the Ausmelt TSL batch converting process has been adapted to the new Ausmelt Continuous Copper Converting (C3) process in response to these industry trends and examines the Ausmelt continuous converting flowsheet options available to the end user.

Jan 1, 2007

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992

What is the BC AMTA? ?What is an ASEP? ?Who are the partners? ?Critical Success Factors ?Questions/Answers Aboriginal Skills and Employment Program (ASEP) ?A collaborative partnership of industry, employers, post secondary, First Nations and government ?Working together to plan and implement training and education programs ?Demand-driven: targeted JOBS for participants

May 1, 2010

By J. W. Austin

"Introduction The Brenda dust collection system was originally designed to handle air at the 5000 ft. elevation with less than 1 grain of dust per cubic feet of air handled. The temperature variation is from 32°C in the summer to -20°C in the winter.DUST COLLECTIONOriginal Equipment 1. Primary Crusher 2 compartment baghouse, shaker type design capacity - 17,000 cfm2. Primary Screening 3 compartment baghouse, shaker type design capacity - 30,000 cfm3. Secondary Crusher 4 compartment baghouse, shaker type design capacity - 45,000 cfm4. Secondary Screening 4 compartment baghouse, shaker typedesign capacity - 60,000 cfmThe original dust collecting equipment was designed using a napped terylene fabric at an air to cloth ratio of 5:1. The ducting was designed to handle the dust laden air at 3200 ft. per minute with all elbows and blast gate sections rubber lined. The hoods and the pickup velocities were designed to handle the anticipated low dust counts."

Jan 1, 1976

By Yongbao Zhu

The Ag2O-mediated reactions of cycloaurated compounds with a general formula Au(L)Cl2 (L = bi-dentate C?N ligand) with thiosalicylic acid, N-acetyl cysteine or 1,2-benzenedithiol in DMF proceeds via ligand substitution of the Au?Cl bonds to afford the S-O and S?S adducts all in good yields. The reactivity of the dichloro, S-O and S-S adducts towards thiols were examined by reacting with cysteine in an aqueous medium, revealing that all of Au-Cl, Au-O and Au-N are labile for thiol displacement. The measurement of the inhibitive activities of these compounds against human cathepsins B and K showed that the dichloro and S-O adducts are effective inhibitors with IC50 values ranging from 0.1 to 2.6 -M, and that the S-S adducts are inactive.

Oct 1, 2003