Search Documents

By Jacques Nantel

"The molybdenite property of Brynnor Mines Limited, Boss Mountain Division (wholly-owned subsidiary of Noranda Mines Limited), is situated approximately 360 miles northeast of Vancouver on the east slope of Takom-kane mountain in British Columbia's Cariboo District. Orebodies at the deposit fall into two categories; quartz breccia, and veins and stringers. The development of the breccia ore zone was started in June, 1964. The bulk of the ore is being mined from the stringer ore zone. The ore-body has been divided into 100-foot stopes and pillars. A sub-level blasthole method is used and the broken ore is handled in drawpoints and scram drifts. The development, drilling, blasting and handling of the ore are reviewed. The future pillar recovery operation is also analysed. The paper is also concerned with a scheduled shaft sinking program."

Jan 1, 1970

By S. Kelebek, U. Demir, T. C. H. Richards, E. Koss

"Laboratory-scale tests were carried out to investigate the response of a high-grade (~143 g/tonne) well-liberated gold ore to flotation using two collector types. Octyl and amyl xanthates, representing conventional types of collectors, were tested against an n-octanoic and hexanoic acids under moderate and high redox potential conditions. The latter was based upon a suggestion in literature that monocarboxylic acids are able to adsorb onto the surface of gold at redox potentials near 600 mV (SCE). This investigation did not demonstrate that these carboxylic acids could function as collectors for gold in real ores. In fact, they appear to have slightly depressed gold. However, the results demonstrated that octyl and amyl xanthates acted as highly effective gold collectors for this ore and that an increase in the collector dosage led to an increase in recovery for all mean particle sizes. In some tests, gold recoveries of around 95% were attainable in concentrates with grades around 6 kg/tonne, indicating that xanthate flotation remains a viable means of concentrating gold even at coarse grain sizes. Various aspects of the process such as grade-recovery performance and recovery by size are discussed.INTRODUCTION Three methods are used for the recovery of gold in mineral processing, either alone or in combination: gravity concentration, cyanidation and flotation. Gold occurs as a by-product in some ores together with platinum group metals and as the primary metal in other ores in the form of native gold and electrum, which are alloys of gold, silver and minor amounts of copper. Flotation is a viable method for recovering liberated gold where the gold is visible under an optical microscope (greater than 1 µm in size) and where the attachment of gold grains is not prevented due to bubble loading by competing minerals. It is generally known that grains finer than 150 µm in size will float with most collectors."

Jan 1, 2017

By Côme Carbonneau

The ten -year case history of La Société Québécoise d'Exploration Minière (SOQUEM) is reviewed under the headings of the company's raison d'être, objectives, policies, structure and final goal. A brief analysis of its past operations is presented: aborted efforts, findings and developments. A projection is made of the future earnings, in terms of estimated present value, of its three main discoveries - Louvem , Niobec and Selim.

Jan 1, 1978

By J. Kan

In order to determine the recovery functions in an oil sand circuit it is necessary to have more than a minimal determination the mass flows in the network. This over-determination is essential in order to allow for measurements within the flow matrix "to flex" according to an error function. It is then possible to identify the flows and composition at all points with maximum likelihood. These so-called full mappings are not easily obtained. However, in order to obtain an unequivocal determination of all the unit operations recoveries such a balance is needed. When databases are constructed exclusively with coherently balanced sets of data it is possible to obtain a maximally accurate process model by maximizing the probability of correctly identifying the process causality. Indeed, it is doubtful in cases of normal complexity that any sense can be made of data that is not so balanced. Coherent mass energy balancing is a tool developed by mineral processing scientists and engineers. Its rigorous application to oil sands is the subject of this paper. The additional element associated with hydrocarbon requires special considerations. It is shown that at least one currently available mineral processing tool will solve the full-mapping problem for an oil sand operation. Experimental design constraints are discussed in this paper relating to the development of databases for the development of effective process models.

May 1, 2004

By K. G. Chipman

IN 1936, the Department of Mines and Resources was formed by the amalgamation of the former Departments of Mines, Interior, Indian Affairs, and Immigration. In the amalgamation, the Geological Survey and the Topographical Survey became the major divisions of the Bureau of Geology and Topography, which is a part of the Mines and Geology Branch which, in turn, is a part of the Department of Mines and Resources. The Topographical Survey was formed by combining the former Topographical Division of the Geological Survey and the air and ground mapping sections of the former Topographical and Air Survey Bureau of the Department of the Interior. The latter organization, previous to 1933, had been known as the Topographical Surveys Branch of the Department of the Interior. The amalgamation of 1936 definitely placed on the Topographical Survey the responsibility for the original mapping required for the development of our natural resources. The war has brought upon us the situation where all work has had to be in the furtherance of the war effort. With decreased staff and limited appropriations, the mapping on those scales which are directly concerned with the natural resources has been confined to the search for oil and strategic minerals. The reconstruction period will produce a different situation, with different problems. The past is behind us and it is necessary to prepare for the future. First, we should consider briefly a few general principles in the making and using of maps, then take stock of what we have, see what the needs are, and consider how we are to meet these needs.

Jan 1, 1944

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By William W. Shilts

"In carrying out a geotechnical survey of a proposed gas pipeline route from the Arctic Islands south to Longlac, Ontario, the Polar Gas Consortium contracted the drilling of several hundred 2- to 2D-m-deep boreholes in drift and bedrock. Samples from these holes were made available to the Geological Survey of Canada, where they were subjected to stratigraphic and trace-element geochemical analyses. The geochemical characteristics of the clay and sand-sized heavy mineral fractions of till samples from these boreholes have been summarized in a series of geochemical profiles.From the proposed pipeline terminus at Longlac northward to the vicinity of God's River in Manitoba, tills contain significant amounts of Paleozoic carbonate rocks and Proterozoic sedimentary rocks derived from the Hudson Bay basin and lowlands. Within this section, two sites were enriched in base metals, indicating the possibility of local mineralization of possible economic interest.From God's River northward to Seal River, Manitoba, no evidence of local mineralization was noted. The heavy mineral fractions of the tills are universally enriched in Mn-rich siderite thought to originate on or in the Paleozoic section of the Hudson Bay lowlands.From Seal River northward to Thelon River, near Baker Lake, tills contain only components originating west of the Hudson Bay sedimentary basin. Near the Keewatin-Manitoba border, all till is enriched in uranium, which probably originates in the ""young"" porphyritic granites underlying much of the region, and produces a distinctive airborne radiometric anomaly.At the Thelon River, multiple till sections are variously enriched in Cr, Ni, U, Cu and Mo in the vicinity of a distinctive aeromagnetic anomaly.From Thelon River northward, several coincident zones of chromium and uranium enrichment are found where the line of boreholes crosses east-west-striking belts of volcanic, ultramafic and sedimentary rocks of the Prince Albert Group.The results of this study indicate that till tends to have characteristic element associations or concentrations over each of several broad regions along the pipeline route. These are related both to large-scale bedrock associations and to largescale effects of glacial dispersal. In addition, the samples, collected more or less at random with respect to local bedrock geology, have intersected several small-scale geochemical anomalies that appear to be related to zones of mineralization of possible economic interest."

Jan 1, 1980

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By B. Tonn, F. Kröger

"The continued development in engine technology is leading to an augmentation in power density which steadily elevates the requirements for thermally and thermo-mechanically highly loaded components such as cylinder heads and pistons. Due to these high performance requirements conventionally applied Al-Si alloys have reached their application limits, since their mechanical properties deteriorate quickly under the influence of heat. Improved applicability is given by Al-Cu-based casting alloys which have a superior high-temperature strength than Al-Si alloys. Since Al-Cu alloys exhibit insufficient casting characteristics, especially regarding hot tearing susceptibility and increased tendency for porosity, it is currently not possible to cast geometrically complex components in robust permanent mold casting processes. The further development of Al-Cu alloys is aimed at finding an optimum between improved castability while high-temperature strength and thermal conductivity are not deteriorated. It is known that a high amount of eutectic reduces the hot tearing susceptibility of an alloy, but it reduces thermal conductivity at the same time. In this paper it will be presented how the conflicting objectives – improved high-temperature strength, good thermal conductivity and reduced hot tearing susceptibility – can be brought together to develop an optimized Al-Cu alloy for application in permanent mold casting.INTRODUCTION At the beginning of the 21st century car, engine blocks were primarily made of gray cast iron (GJL). Less than half a decade later, the choice of material had shifted towards lightweight materials. Ever since, the car engine manufacturing is dominated by aluminum-based alloys. The weight of car engine blocks could thus be reduced by around 50% due to the lower specific weight of aluminum alloys compared to gray cast iron. Furthermore, the high thermal conductivity of aluminum alloys allowed a reduction of complex cooling channel systems and thereby promoted the advancement of this material group. The further development in engine technology leads to an augmentation in power density which elevates the requirements for thermally and thermo-mechanically highly loaded components. For example, in diesel-powered car engines the upper required limits can reach an ignition pressure as high as 230 bar and gas temperatures of up to 1000°C. Thereby, thermal loads can cause high alternating thermal stresses (Grzincic, 2003) which can effectively be reduced by providing high thermal conductivity."

Jan 1, 2017

By T. Banerjee, Y. Dumais, R. Lemire

"Agnico Eagle LaRonde produces over 300,000 ounces of gold annually, along with silver, zinc and copper by-products. The LaRonde plant consists of a conventional SAG and Ball mill circuit, followed by flotation. Load management is imperative for maintaining stability in grind size and ensuring consistency of the flotation feed. In flotation, the mass pull profiles of the cells and reagent dosage rates need to be managed to maximize recovery, while maintaining product quality. This is achieved by controlling the air, level and reagent addition set-points across the circuit. However, disturbances such as feed size distribution, ore hardness and mineralogy make it challenging to maintain efficient control using traditional control techniques. LaRonde therefore worked to develop a progressive control strategy, targeting stability and optimization. This started with a year-long instrumentation upgrade campaign, focusing on optimizing the performance and reliability of plant-wide instrumentation. The process was then optimized, leveraging AwaRE advanced controllers running in closed loop with PARC modules embedded within the PLC. The installation of 8 PFC cameras in flotation changed the flotation operation from a level and air control based strategy, to one that controls mass pull. This new control philosophy has allowed the plant to effectively manage mill load, improving grind size and providing increased throughput with better flotation performance.INTRODUCTION Background Since 2015, Agnico Eagle LaRonde has been conducting an optimization campaign to maximise the performance of plant assets leveraging instrumentation and control. The grinding and copper flotation circuits were identified as the areas having the greatest opportunities and value proposition for advanced control. A disciplined approach was followed to design and implement a progressive control solution to achieve operational excellence."

Jan 1, 2018

By J. C. Gathje

Newmont&apos;s Phoenix Project is located near Battle Mountain, Nevada and is scheduled to produce copper concentrates containing high precious metal values. High temperature pressure oxidation (PDX) of the concentrates was considered as a treatment option during process development. The metals content in Phoenix concentrates range from: 15-25% for Cu, 1-10% for Zn, 0-2% for Pb and ?27% Fe. The precious metals content of the Phoenix concentrates can range up to ?300 g/t Au and >3,000 g/t Ag. As a consequence it was necessary that any process for consideration should have the capability of recovering both the copper and precious metal values. Typically, gold can easily be leached from the autoclave discharge solids, but silver is chemically bound with the jarosite formed and cannot be directly leached. Laboratory investigations led to the development of a patented PDX process that minimizes the formation of jarosite so that the silver can be leached easily along with the gold. The process was confirmed with extensive pilot plant testing. Excellent solution extraction of copper and zinc was achieved, and both iron and lead were precipitated in the PDX residue. The process produces clean PDX discharge liquors with very low iron concentrations. As an example, conventional PDX techniques resulted in pregnant liquors containing ?5 g/L Fe. However, the Newmont process, which controls the iron and sulfate species, achieved high iron precipitation in the PDX solids and pregnant liquors containing <0.5 g/L Fe. High gold and silver recoveries were achieved by direct cyanidation of the PDX solids. This process has the added benefit of producing PDX solids that demonstrate superior settling and filtration characteristics.

Jan 1, 2006

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019

By A. G. Spencer

"The horsepower required to drive large grinding mills has increased dramatically during the past ten years. Limitations on the amount of power which may be transmitted by a single gear and pinion have resulted in the application of multimotor drives, with consequent loadsharing problems. It has also sparked the development of some entirely new drive concepts. In addition, the severe demands made upon the electrical system during the acceleration period have required that the selection of motors and electrical system design be closely coordinated. Moreover, the installation of such large process units results in downtime being very costly. The equipment selected and the plant maintenance philosophy must therefore be such as to minimize the risk of unscheduled downtime."

Jan 1, 1972

By Karl J. C. Harries

"11.1. INTRODUCTIONA royalty is the most common form of interest retained by an owner who is disposing of his property or by a joint venturer who ceases, voluntarily or otherwise, to participate in the joint venture.1 Rarely does a non-participating party have a direct interest in the property and/or assets of a project, except during the period when a non-participating joint venturer may be having his interest diluted.2 In fact, it is most unwise to permit a non-participating party to have such an interest. It may give rise to significant problems that could prevent or substantially delay the development of an orebody and require a considerable amount of time, effort, and money to correct.3In negotiating a royalty, it is important to be aware that there is no law or convention that says, “You just don’t do that in a royalty agreement.” As with any agreement, inventiveness and flexibility on the part of the negotiator are not just assets, but virtual necessities. It is also for this reason that it is essential to read the royalty provisions, particularly the definitions, fully and carefully, especially if you are the recipient. On the other hand, if your inventiveness and flexibility cause your accountant to question the advisability of one of your ideas, pay close attention to him.4 He will, no doubt, have had experience with many royalties, and no competent professional adviser disparages a client’s ideas without good reason. Besides, he will probably be the person who will be determining the royalty or certifying the determination of it. At the very least, he will be auditing your general financial statements, which must, of course, reflect the royalty determination. Heeding his advice not only may make the determination easier but also will probably save you money in professional fees later on. Nevertheless, do not simply accept his comments or recommendations without understanding what they mean, why they have been made with respect to your royalty agreement (sometimes professionals have comments that they make as a matter of course and, even though they may be valid, you should require them to be justified to you), and how they will affect your royalty determination.It is surprising how many corporate payors insist that their standard royalty provisions5 be used as a matter of policy, thereby effectively tying the negotiator’s hands. It is even more surprising, and to professional advisers frightening, how many of the senior employees who insist that such a policy be adhered to, virtually without variation, do not know what is in the standard provisions and would be hard-pressed to explain them to a property owner. If standard provisions are appropriate, by all means use them, but do allow experienced and sensible negotiators some flexibility and make sure that everyone within the corporation who may have to use such provisions – negotiator and supervisor alike – knows what they contain and why they are as they are. For example, there are often good and convincing reasons to describe a deduction in a certain way or to include a certain specific type of deduction. On the other hand, quite often the answer to the question “why?” is that “it has always been there”; this is, or should be, an unacceptable answer. In any event, if you, as the negotiator, appear to know what you are talking about, are familiar and comfortable with your royalty provisions, and are backed up by your boss with the same words or reasoning, a property owner cannot help but be satisfied that you are knowledgeable, even if he still does not agree with your provisions. Finally, if you do use standard provisions, make sure that they are reviewed and updated regularly."

Jan 1, 2003

By Carlos Rebolledo, Nelson Parra

Arsenic is an unresolved problem in the mining industry considering the fact that most of the new copper deposits have high arsenic contents; stricter environmental restrictions for handling, transporting and processing complex materials are expected and stable abatement of arsenic is not extensively applied. In 2018 Chile produced 24.5% of the total copper from concentrates and in the future copper production in Chile is expected to increase, mainly associated with production of concentrates that will also contain more arsenic. China has set an import benchmark of maximum 0.5% for arsenic content in copper concentrates and this value is expected to be more restrictive in the future. On the first day of 2018 China banned the importation of scrap. Blending practice has been a business option, but it is not sustainable in the future, as “normal” copper concentrates become less and less clean. By the end of 2018, Chile formulated new regulations, increasing the capture of SO2 and arsenic to 95%. In order to comply with these regulations Chilean smelters had to make large invest large amounts of money. Disposing of arsenic as a stable residue is a pending issue. EcoMetales is a 100% subsidiary of Codelco and provides the mining industry with environmental solutions. It has a plant near Calama in Chile that treats flue dust from smelters, refinery effluents and acid solutions from acid plants. EcoMetales is fully committed to contributing to the solution to the arsenic problem. Currently we are developing four main projects: 1) Concentrates treatment. A PLCC project considering the treatment of 200 ktpy of copper concentrates with arsenic from the northern district of Codelco; 2) EPAS DET project considering the treatment of 700 m3/d of weak acid solution with arsenic from the of El Teniente devision of the Codelco acid plant; 3) Borras project, considering the recovery of valuable metals (Cu, Ag, Ge, Pb) from the flue dust leaching plant; 4) Tailings project, considering the recovery of metal values from tailings. The purpose of this work is to present the trends and treatment processes for arsenic handling in the copper mining industry with a focus on the scorodite process. INTRODUCTION Between 2000 and 2015 the global copper concentrates production has grown from approximately eleven to fifteen million metric tons per year. Chile produced 26.5% of the total copper from concentrates and in the future copper production in Chile is expected to increase, mainly as a result of the production of concentrates (Figure 1)

Jan 1, 2019

By Jonathan Ruiz Lizardo, Met-Chem Canada Inc., Flavio Ccuno, Constante Umipig, Ewald Pengel, José Ruiz

"Cerro de Maimón is located in the Dominican Republic on the island of Hispaniola approximately 75 kilometers northwest of the capital city, Santo Domingo. The processing facility consisted of two separate processing plants for oxide and sulphide ores. The oxide plant processed oxide ore bearing gold and silver ore using cyanide leaching and Merrill Crowe processes, while the sulphide plant produced a copper concentrate using conventional flotation. Cormidom is a commendatory example how mineral processing facilities can co-exist in balance with the environment. In 2014, natural occurring copper oxide contamination with finer grained copper-zinc sulphide mineralisation was expected to dominate the sulphide ore body. In anticipation Cormidom contacted the original plant designer Met-Chem to assist in overcoming this challenge. Test work indicated that increased flotation time and subsequent very fine grinding were required. Met-Chem provided the detailed engineering and Cormidom proceeded with the expansion project internally. Currently Cormidom has processed the sulphide ore successfully by implementing flotation modifications. This paper describes the history of Cormidom, test work on the “new” ore body, modification in process design in the Cu-Zn sulphide flotation circuit, construction and implementation.INTRODUCTIONCorporación Minera Dominicana (CORMIDOM) was a wholly owned subsidiary of GlobeStar Mining Corporation (a Canadian based minerals exploration company) with extensive exploration of base and precious metals in the Dominican Republic. In 2007-2008 CORMIDOM constructed the Cerro de Maimom project. The company was subsequently sold and purchased by Perilya Limited from Australia in 2013. Cerro de Maimón is located in the Dominican Republic on the island of Hispaniola approximately 75 kilometers northwest of the capital city, Santo Domingo. It is near the town of Maimón in Monsenor, Nouel Province (see Figure 1)."

Jan 1, 2016

By D. H. Stonehouse

Of the f ive Canadian cement producing regions- Atlantic, Quebec, Ontario, Prairie and Pacific-Ontario has the greatest capacity and normally produces the most cement. However, during the last 5 years the greatest activity within the industry in Canada has been in the Prairie and Pacific regions where major capacity increases have taken place. Most Canadian cement companies produce normal Portland, high-earlystrength Portland and sulphate resisting Portland cements. Some companies also manufacture moderate Portland cement, and low-heat-of-hydration Portland cement. Escalating energy costs highlight the need for technology research into more energy-efficient equipment for the energy-intensive cement industry. The industry is well integrated and plants are well situated to support construction in Canada. Expansion into the United States has become common during the past decade.

Jan 1, 1984

By Y. P. Malhotra, JE. C. Carter

"Syncrude&apos;s overburden removal requirement ranges from 20 million to 30 million bank cubic metres per year to meet tarsand demands for the production of 129,000 barrels of synthetic crude oil per day. The economic tar-sand lies beneath a variable thickness of overburden materials, composed of silts, clays, some sands of lacustrine origin, wind-deposited sand dunes, and out-wash sands and gravels.For the removal of overburden, Syncrude commissioned its own mobile equipment fleet in January 1981. This fleet consists of two Demag 241 hydraulic shovels, ten Titan 33-15B trucks and support equipment. Prior to this, all overburden removal was being carried out by contractors.This paper presents an overview of overburden removal at Syncrude, with particular reference to the performance of its own fleet.IntroductionThe Syncrude Tar Sands Plant was officially opened on September 15, 1978. After an expenditure of approximately $2.26 billion, the second and the largest commercial tarsands plant was on stream toward a permit production rate of 129,400 barrels of synthetic crude oil per day. The Syncrude Plant, a joint venture of six oil companies, the federal government and the Alberta government, is a major step forward toward the goal of Canadian energy self-sufficiency.The Mildred Lake operation of Syncrude Canada Ltd. Is located 40 km north of Fort McMurray and 480 km northeast of Edmonton in the Province o f Alberta.Synthetic crude oil leaving the plant is a blend of two-third s gas oil and one-third naphtha. The two streams combine in a pipeline and flow to Edmonton. The product takes six days to make the journey, arriving at four locations in the city Imperial&apos;s Strathcona Refinery, Gulf&apos;s Edmonton Refinery, the Interprovincial pipeline terminal and the Trans-Mountain pipeline terminal. Each Syncrude owner receives a share of oil equal; to its percentage of ownership in the project. At the present time, the oil is being utilized by Canadian refineries from Vancouver to Montreal."

Jan 1, 1983

By Hatch, A. Reple, W Valery

The mining industry is facing declining feed grades which require the mining and processing of larger volumes of material per tonne of product. Pre-concentration aims to remove barren material at as coarse a particle size and as early in the process as possible to reduce processing costs, energy consumption, water losses, and greenhouse gas emissions while increasing production and profitability. This may be achieved using bulk ore sorting—the separation of barren gangue from a fully loaded conveyor belt based on the grade as measured or inferred from a sensor. This paper evaluates the technical and economic viability of bulk ore sorting for the PanAust Phu Kham copper deposit in Lao PDR. Bulk ore sorting technology is described briefly along with discussion of appropriate sensor and diversion systems for the Phu Kham operation. To evaluate the economic implications, the actual mined material and costs from 2014 were used as the base-case. Sampling data was not available; therefore, the ore grade variability that would feed a bulk ore sorter was estimated using geo-statistical tools based on mine grade control data. The sorter performance when treating this material was simulated considering the accuracy of the sensor measurement and errors associated with material diversion. The impact on inferred cash flow was estimated for several different scenarios considering the additional costs for sorter operation and reject handling. The evaluation demonstrated that bulk ore sorting at Phu Kham has the potential to increase the amount of metal in product and/or reduce processing plant throughput (and costs) to improve the annual inferred cash flow for the conditions investigated. The sorter is the gatekeeper – only material above the cut-off grade (value-adding) reports to the processing plant; no waste dilutes the feed. Likewise, above cutoff grade material is not lost to waste; preventing lost revenue.

Jan 1, 2016

By H. L. Snyder

This paper outlines the approach to the underground construction work involved in the Churchill Falls Power Project. It is the first in a series of papers which CIM Bulletin plans to publish as the different 11hases of this large-scale operation evolve.

Jan 1, 1968